scholarly journals Competitive adsorption and mechanism of hexahydroxy metallic system by aminated solution-blown polyacrylonitrile micro/nanofibers

2021 ◽  
Author(s):  
Huiqing Lou ◽  
Siyu Li ◽  
Xiangwei Feng ◽  
Xianzhong Cao
Keyword(s):  
Heavy Metal ◽  
Metal Ions ◽  
Adsorption Capacity ◽  
Metal Ion ◽  
Metal Removal ◽  
Interactive Effect ◽  
Maximum Adsorption Capacity ◽  
Coupling Mechanism ◽  
Metal System ◽  
Metallic System

Abstract Adsorptive properties for Cd(II), Cr(III), Cu(II), Ni(II), Pb(II) and Zn(II) onto an amidoxime-functionalized polyacrylonitrile (APAN) micro/nanofibers were systematically investigated in hexahydroxy metallic solution system using batch experiments. The interactive effect of multi-metal ions in multi- metal systems was antagonistic in nature, and the adsorption capacity in multi-metal system was lower than that in single-metal system. The Langmuir isotherm model could explain respectively the isotherm and kinetic experimental data for hexahydroxy metallic system with much satisfaction. The maximum adsorption capacity in hexahydroxy metallic for Cd(II), Cr(III), Cu(II), Ni(II), Pb(II) and Zn(II) was calculated to be 98 mg/L, 158 mg/L, 80 mg/L, 76, 312 and 58 mg/L individually. The APAN micro/nanofibers possessed good selectivity toward Pb(II) and Cr(III), over Cd(II), Cu(II), Ni(II), and Zn(II), having the highest selectivity coefficients at 17.52 and 6.07 in the test range. The five adsorption-desorption cycle experiments exhibited that APAN micro/nanofibers adsorbent are readily reusable, and have potential for heavy metal removal from wastewater. The adsorption behavior in multi-metal systems was shown to be complex, including surface complexation, antagonistic competition and displacement reactions. The diversity and selectivity in metal ion adsorption onto the micro/nanofibers relate mainly to the stability constants, and the microscopic coupling mechanism between the heavy metal ions and the functional groups on the fiber surface. This interaction mechanism between the favorable component and other metal ions could contribute significantly to the direct displacement impact illustrated schematically.

Potential of Agricultural Waste Material (Ananas cosmos) as Biosorbent for Heavy Metal Removal in Polluted Water

2020 ◽  
Vol 1010 ◽  
pp. 489-494
Author(s):  
Abdul Hafidz Yusoff ◽  
Rosmawani Mohammad ◽  
Mardawani Mohamad ◽  
Ahmad Ziad Sulaiman ◽  
Nurul Akmar Che Zaudin ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Adsorption Capacity ◽  
Metal Removal ◽  
Low Cost ◽  
Agricultural Waste ◽  
Heavy Metal Removal ◽  
Polluted Water ◽  
Maximum Adsorption Capacity ◽  
Pineapple Peel

Conventional methods to remove heavy metals from polluted water are expensive and not environmentally friendly. Therefore, this study was carried out to investigate the potential of agricultural waste such as pineapple peel (Ananas Cosmos) as low-cost absorbent to remove heavy metals from synthetic polluted water. The results showed that Cd, Cr and Pb were effectively removed by the biosorbent at 12g of pineapple peels in 100 mL solution. The optimum contact time for maximum adsorption was found to be 90 minutes, while the optimum pH for the heavy metal’s adsorption was 9. It was demonstrated that with the increase of adsorbent dosage, the percent of heavy metals removal was also increased due to the increasing adsorption capacity of the adsorbent. In addition, Langmuir model show maximum adsorption capacity of Cd is 1.91 mg/g. As conclusions, our findings show that pineapple peel has potential to remove heavy metal from polluted water.

scholarly journals Removal of Selective Metal Ions from Water with Hydroxy Propyl Cellulose Hydrogel

2019 ◽  
Vol 31 (3) ◽  
pp. 602-606
Author(s):  
Ch. Shanti Devi ◽  
S. Manimukta Devi ◽  
N. Shubhaschandra Singh
Keyword(s):  
Metal Ions ◽  
Adsorption Capacity ◽  
Metal Ion ◽  
Vinyl Pyrrolidone ◽  
Poly Vinyl Alcohol ◽  
Maximum Adsorption Capacity ◽  
Cellulose Hydrogel ◽  
Potential Applications ◽  
Removal Of Metal ◽  
Poly Vinyl Pyrrolidone

In this study, environmentally friendly hydrogels prepared from hydroxy propyl cellulose hydrogels blended with poly(vinyl alcohol) (PVA) and poly(vinyl pyrrolidone) (PVP) were employed to absorb selected metal ions of Cu and Fe to find potential applications in removal of metal ion from water or in wastewater treatment. Highest adsorption capacity of hydroxy propyl cellulose hydrogels blended with PVA or PVP is shown at 0.04 % (w/v) of the metal ion solutions. Hydroxy propyl cellulose hydrogel when blended PVA has shown greater adsorption of Fe(III) ion than Cu(II) ion at higher pH. Hydroxy propyl cellulose hydrogel when blended with PVP also showed maximum adsorption capacity rather than PVA blended hydrogel.

scholarly journals Plant-Based Tacca leontopetaloides Biopolymer Flocculant (TBPF) Produced High Removal of Heavy Metal Ions at Low Dosage

Processes ◽  
2020 ◽  
Vol 9 (1) ◽  
pp. 37
Author(s):  
Nurul Shuhada Mohd Makhtar ◽  
Juferi Idris ◽  
Mohibah Musa ◽  
Yoshito Andou ◽  
Ku Halim Ku Hamid ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Metal Ions ◽  
Metal Ion ◽  
Metal Removal ◽  
Test Procedure ◽  
Synthetic Wastewater ◽  
Leachate Treatment ◽  
Low Concentration ◽  
Removal Of Heavy Metals

High removal of heavy metals using plant-based bioflocculant under low concentration is required due to its low cost, abundant source, and nontoxicity for improved wastewater management and utilization in the water industry. This paper presents a treatment of synthetic wastewater using plant-based Tacca leontopetaloides biopolymer flocculant (TBPF) without modification on its structural polymer chains. It produced a high removal of heavy metals (Zn, Pb, Ni, and Cd) at a low concentration of TBPF dosage. In our previous report, TBPF was characterized and successfully reduced the turbidity, total suspended solids, and color for leachate treatment; however, its effectiveness for heavy metal removal has not been reported. The removal of these heavy metals was performed using a standard jar test procedure at different pH values of synthetic wastewater and TBPF dosages. The effects of hydroxide ion, pH, initial TBPF concentration, initial metal ion concentration, and TBPF dosage were examined using one factorial at the time (OFAT). The results show that the highest removal for Zn, Pb, Ni, and Cd metal ions were 98.4–98.5%, 79–80%, 97–98%, and 92–93%, respectively, using 120 mg/L dosage from the initial concentration of 10% TBPF at pH 10. The final concentrations for Zn, Pb, Ni, and Cd metal ions were 0.043–0.044, 0.41–0.43, 0.037–0.054, and 0.11–0.13 mg/L, respectively, which are below the Standard B discharge limit set by the Department of Environment (DOE), Malaysia. The results show that TBPF has a high potential for the removal of heavy metals, particularly Zn, Pb, Ni, and Cd, in real wastewater treatment.

scholarly journals Heavy Metal Removal from Aqueous Solution Using Biosurfactants Produced by Pseudomonas aeruginosa with Corn Oil as Substrate

2018 ◽  
Vol 18 (3) ◽  
pp. 472
Author(s):  
Venty Suryanti ◽  
Sri Hastuti ◽  
Tutik Dwi Wahyuningsih ◽  
Mudasir Mudasir ◽  
Dian Kresnadipayana ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Heavy Metal ◽  
Metal Ions ◽  
Contact Time ◽  
Metal Ion ◽  
Metal Removal ◽  
Corn Oil ◽  
Metal Ion Removal ◽  
Ion Removal ◽  
Removal Capacity

The batch removal of Cu(II), Cd(II) and Pb(II) from individual heavy metal ion aqueous synthetic solution using biosurfactants produced by Pseudomonas aeruginosa with corn oil as substrate was investigated. The metal ion removal process of crude preparation biosurfactants (CPB) was established to be dependent on the initial pH and contact time. The optimum metal removal was observed at pH 6.0 of the initial metal solution and 10 min of contact time. The affinity sequence for metal ion removal was Pb(II)>Cd(II)>Cu(II). The removal capacity value of biosurfactant for Cu(II), Cd(II) and Pb(II) from single metal ions solution were 0.169, 0.276 and 0.323 mg/g, respectively. The removal capacity value of biosurfactant for Cu(II), Cd(II) and Pb(II) from multi metal ions solution were 0.064, 0.215 and 0.275 mg/g, respectively. The removal capacity of individual metal ion was diminished by the presence of other metal ions in multi metal ions from synthetic aqueous solution. The removal capacity value of biosurfactant for Cu(II), Cd(II) and Pb(II) from silver industry wastewater were 0.027, 0.055 and 0.291 mg/g, respectively. The results indicated that biosurfactants have potential to be used in the remediation of heavy metals in industrial wastewater.

scholarly journals Insights into the Recent Use of Modified Adsorbents in Removing Heavy Metal Ions from Aqueous Solution

2021 ◽  
Vol 12 (2) ◽  
pp. 1884-1898
Keyword(s):  
Aqueous Solution ◽  
Heavy Metal ◽  
Metal Ions ◽  
Metal Ion ◽  
Heavy Metal Ions ◽  
Metal Removal ◽  
Low Cost ◽  
Ion Concentration ◽  
Future Research ◽  
Batch Tests

Natural water gets contaminated with heavy metal ions because of industrial effluents' discharge into the aquatic environment. As these heavy metal ions cause various health hazards, they should be removed from the aqueous solution. Heavy metal ion concentration in the aqueous solution is very less, so conventional metal removal and recovery processes cannot be applied here. The adsorption method is a great alternative to all these processes as it is a cost-effective and easy method. The use of natural, low-cost materials as adsorbents is eco-friendly also. However, metal uptake capacity of low-cost materials is very less. So, modification is required for low-cost materials to increase their efficiency. In the present review, different modification procedures adopted by different researchers have been discussed. Different low-cost materials used are sawdust, fruit and vegetable wastes, soil, minerals, etc. The modifying agents are heat, acids, bases, and other chemicals. Nevertheless, most of the studies are limited to batch tests only. Future research should be carried out on the extension of batch tests to column study for the large-scale treatment of contaminated water, and the cost of modification procedures and their impact on the environment should also be assessed.

scholarly journals Efficient Removal of Heavy Metal Ions in Wastewater by Using a Novel Alginate-EDTA Hybrid Aerogel

2019 ◽  
Vol 9 (3) ◽  
pp. 547 ◽  
Author(s):  
Min Wang ◽  
Zhuqing Wang ◽  
Xiaohong Zhou ◽  
Shikun Li
Keyword(s):  
Heavy Metal ◽  
Metal Ions ◽  
Adsorption Capacity ◽  
Heavy Metal Ions ◽  
Maximum Adsorption Capacity ◽  
Adsorbent Regeneration ◽  
Acid Washing ◽  
Washing Process ◽  
Repeated Use ◽  
Hybrid Aerogel

In this study, we prepared a novel calcium alginate-disodium ethylenediaminetetraacetate dihydrate hybrid aerogel (Alg-EDTA) by chemical grafting and vacuum-freeze-drying to remove heavy metal ions from wastewater. Experimental results show that the as-prepared Alg-EDTA adsorbent has a high affinity for heavy metal ions, such as Cd2+, Pb2+, Cu2+, Cr3+, and Co2+, and can adsorb >85% of metal ions from the corresponding solution. Alg-EDTA also exhibits high selectivity toward Cd2+, and the maximum adsorption capacity for Cd2+ reached 177.3 mg/g, which exceeds the adsorption capacity of most reported Cd2+-adsorbents. Adsorbent regeneration can be achieved by a simple acid-washing process, and adsorption performance of Alg-EDTA remains stable after repeated use. All these findings indicate that Alg-EDTA has a promising prospect in the treatment of heavy metal ions wastewater.

scholarly journals Highly Selective Copper Ion Imprinted Clay/Polymer Nanocomposites Prepared by Visible Light Initiated Radical Photopolymerization

Polymers ◽  
2019 ◽  
Vol 11 (2) ◽  
pp. 286 ◽  
Author(s):  
Radhia Msaadi ◽  
Gorkem Yilmaz ◽  
Andrit Allushi ◽  
Sena Hamadi ◽  
Salah Ammar ◽  
...  
Keyword(s):  
Visible Light ◽  
Metal Ions ◽  
Adsorption Capacity ◽  
Polymer Nanocomposites ◽  
Metal Ion ◽  
Copper Ions ◽  
Maximum Adsorption Capacity ◽  
Imprinted Polymer ◽  
Ion Imprinted ◽  
Ion Imprinting

There is an urgent demand worldwide for the development of highly selective adsorbents and sensors of heavy metal ions and other organic pollutants. Within these environmental and public health frameworks, we are combining the salient features of clays and chelatant polymers to design selective metal ion adsorbents. Towards this end, the ion imprinting approach has been used to develop a novel nanohybrid material for the selective separation of Cu2+ ions in an aqueous solution. The Cu2+-imprinted polymer/montmorillonite (IIP/Mt) and non-imprinted polymer/montmorillonite (NIP/Mt) nanocomposites were prepared by a radical photopolymerization process in visible light. The ion imprinting step was indeed important as the recognition of copper ions by IIP/Mt was significantly superior to that of NIP/Mt, i.e., the reference nanocomposite synthesized in the same way but in the absence of Cu2+ ions. The adsorption process as batch study was investigated under the experimental condition affecting same parameters such as contact time, concentration of metal ions, and pH. The adsorption capacity of Cu2+ ions is maximized at pH 5. Removal of Cu2+ ion achieved equilibrium within 15 min; the results obtained were found to be fitted by the pseudo-second-order kinetics model. The equilibrium process was well described by the Langmuir isothermal model and the maximum adsorption capacity was found to be 23.6 mg/g. This is the first report on the design of imprinted polymer nanocomposites using Type II radical initiators under visible light in the presence of clay intercalated with hydrogen donor diazonium. The method is original, simple and efficient; it opens up new horizons in the general domain of clay/polymer nanocomposites.

A Mesoporous Chelating Polymer-Carbon Composite for the Hyper-Efficient Separation of Heavy Metal Ions

2020 ◽  
Vol 20 (5) ◽  
pp. 3042-3046 ◽  
Author(s):  
Jukyoung Kang ◽  
Tack-Jin Kim ◽  
Jong Won Park ◽  
Kyo-Young Lee ◽  
Doh Hee Park ◽  
...  
Keyword(s):  
Heavy Metal ◽  
Metal Ions ◽  
Adsorption Capacity ◽  
Mesoporous Carbon ◽  
Heavy Metal Ions ◽  
Carbon Composite ◽  
Maximum Adsorption Capacity ◽  
Absorption Data ◽  
Public Health Perspective ◽  
Chelating Polymer

The removal of heavy-metal ions from wastewater is an important objective from a public-health perspective, and chelating agents can be used to achieve this aim. Herein, we report the synthesis of mesoporous carbon as a chelating polymer host using nanoarchitectonics approach. Carboxymethylated polyethyleneimine, a chelating polymer, was incorporated into the mesopore walls of mesoporous carbon to create a polymer-mesoporous-carbon composite. Nitrogen adsorption– desorption experiments and scanning electron microscopy (SEM) were used to illustrate the structural advantages of the composite. Co2+ adsorption by the composite material was examined using cobalt nitrate solutions at pH 3. The study revealed that the Co2+-absorption data are most closely modeled by the Langmuir isotherm. The maximum adsorption capacity, calculated by linear regression, was determined to be about 40 mg-Co/g-composite at pH 3. The composite exhibited about a six-times higher adsorption capacity toward a dilute Co solution (12.5 ppm) than that of the pristine mesoporous carbon. In addition, the composite showed a substantially higher distribution coefficient (Kd = 1.54×105) compared to that (Kd = 2.05×102) of the mesoporous carbon. Overall, we expect that the mesoporous composite, with its large mesopores (~20 nm), will be in high demand for adsorption applications.

scholarly journals Hg selective adsorption on polypropylene-based hollow fiber grafted with polyacrylamide

2017 ◽  
Vol 36 (1-2) ◽  
pp. 287-299 ◽  
Author(s):  
Changkun Liu ◽  
Jizhen Jia ◽  
Ji’an Liu ◽  
Xiaoyan Liang
Keyword(s):  
Heavy Metal ◽  
Metal Ions ◽  
Adsorption Capacity ◽  
Hollow Fiber ◽  
Heavy Metal Ions ◽  
Hollow Fiber Membrane ◽  
Selective Adsorption ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Fiber Membrane

A novel polypropylene hollow fiber membrane with a new function of selective adsorption of mercury ions in aqueous solutions was successfully prepared. The surface of the polypropylene hollow fiber membrane was initially modified with polydopamine by surface polymerization, and subsequently grafted with polyacrylamide (PAM) polymer brush via the surface initiated atom transfer radical polymerization (SI-ATRP) technique (thereafter named as PP-PAM). This study investigated the adsorption performance of Hg(II) ions by PP-PAM and the effect of various influencing factors on Hg(II) ion adsorption. The experiment indicated that the Hg(II) adsorption capacity of the PP-PAM increased with the increase of the pH, and the Hg(II) adsorption kinetics was consistent with the pseudo-second-order kinetic model. The adsorption isotherm followed the Langmuir model, with the maximum adsorption capacity calculated to be 0.854 mmol/g for Hg(II) ions. The adsorption study in multi-component system indicated that PP-PAM preferentially adsorbs Hg(II) over Pb(II) ions, with significant adsorption capacity difference of the two heavy metal ions. This study provided an efficient method for the preparation of the adsorptive polypropylene hollow fiber membrane, which expands its application for the selective removal of heavy metal ions.

scholarly journals Heavy Metal Ion Adsorption Properties of Methacrylamidocysteine-Containing Porous Poly(Hydroxyethyl Methacrylate) Chelating Beads

2002 ◽  
Vol 20 (7) ◽  
pp. 607-617 ◽  
Author(s):  
Adil Denizli ◽  
Bora Garipcan ◽  
Sibel Emir ◽  
Süleyman Patir ◽  
Ridvan Say
Keyword(s):  
Heavy Metal ◽  
Metal Ions ◽  
Metal Ion ◽  
Heavy Metal Ions ◽  
Metal Removal ◽  
Ph Value ◽  
Heavy Metal Removal ◽  
Ion Concentration ◽  
Heavy Metal Ion ◽  
Adsorption Capacities

Details of the adsorption performance of poly(2-hydroxyethylmethacrylate–methacrylamidocysteine) [p(HEMA–MAC)] beads towards the removal of heavy metal ions from aqueous solution were studied. The metal-complexing ligand and/or co-monomer MAC was newly synthesized from methylacrylochloride and cysteine. Spherical beads of average size 150–200 mm were obtained by the radical suspension polymerization of MAC and HEMA conducted in an aqueous dispersion. The p(HEMA–MAC) beads obtained had a specific surface area of 18.9 m2/g. p(HEMA–MAC) beads were characterized by swelling studies, FT-IR spectroscopy and elemental analysis. Such beads with a swelling ratio of 72%, and containing 3.9 mmol MAC/g, were used for heavy metal removal studies. The adsorption capacities of the beads for selected metal ions, i.e. CdII, AsIII, CrIII, HgII and PbII, were investigated in aqueous media containing different amounts of these ions (10–750 mg/l) and at different pH values (3.0–7.0). The adsorption rate was fast in all cases. The maximum adsorption capacities of the p(HEMA–MAC) beads were 1058.2 mg/g for CdII, 123.4 mg/g for AsIII, 199.6 mg/g for CrIII, 639.1 mg/g for PbII and 1018.6 mg/g for HgII. On a molar basis, the following affinity order was observed: CdII > HgII > CrIII > PbII >AsIII. The adsorption capacity of the MAC-incorporated beads was affected significantly by the pH value of the aqueous medium. The adsorption of heavy metal ions from artificial wastewater was also studied. In this case, the adsorption capacities were 52.2 mg/g for CdII, 23.1 mg/g for CrIII, 83.4 mg/g for HgII, 62.6 mg/g for PbII and 11.1 mg/g for AsIII at an initial metal ion concentration of 0.5 mmol/l. The chelating beads could be regenerated easily with a higher effectiveness by 0.1 M HNO3. These features make p(HEMA–MAC) beads potential candidates for heavy metal ion removal at high capacity.

Sign in / Sign up

Export Citation Format

Share Document