scholarly journals Effective removal of heavy metal ions from aqueous solutions using a new chelating resin poly [2,5-(1,3,4-thiadiazole)-benzalimine]: kinetic and thermodynamic study

2015 ◽  
Vol 6 (2) ◽  
pp. 310-324 ◽  
Author(s):  
Selvaraj Dinesh Kirupha ◽  
Selvaraj Kalaivani ◽  
Thangaraj Vidhyadevi ◽  
Periyaraman Premkumar ◽  
Palanithamy Baskaralingam ◽  
...  
Keyword(s):  
Metal Ions ◽  
Metal Ion ◽  
Ph Value ◽  
Thermo Gravimetric Analysis ◽  
Kinetic Studies ◽  
Ion Concentration ◽  
Chelating Resin ◽  
Gravimetric Analysis ◽  
Equilibrium Data ◽  
Experimental Values

A novel poly [2,5-(1,3,4-thiadiazole)-benzalimine] abbreviated as TDPI adsorbent was synthesized using simple polycondensation technique. The synthetic route involves the preparation of 2,5-diamino-1,3,4-thiadiazole from 2,5-dithiourea and subsequent condensation with terephthalaldehyde. The resin was chemically characterized using Fourier transform infrared (FT-IR), 1H-NMR, and 13C-NMR spectroscopic analysis. Surface morphology and thermal stability were analyzed using scanning electron microscopy (SEM) and thermo-gravimetric analysis (TGA). The effect of the pH value of solution, contact time, adsorbent dose, and initial metal ion concentration were investigated by batch equilibrium adsorption experiments. Kinetic studies show that the adsorption of metal ions onto the resin proceeds according to the pseudo-second-order model and the equilibrium data were best interpreted by the Redlich–Peterson isotherm. The experimental values of the adsorption capacities of Pb2+, Cu2+, Ni2+, and Cd2+ on to TDPI could reach up to 437.2, 491.6, 493.7, and 481.9 mg.g−1 respectively. The exothermic nature of the process, the affinity of the adsorbent towards the metal ions and the feasibility of the process are explained in the thermodynamic parameters. The resin stability and re-usability studies suggest that the resin is chemically stable (0.3 N HCl and H2SO4) and could be regenerated without any serious decline in performance.

Application of radiation grafted waste polypropylene fabric for the effective removal of Cu (II) and Cr (III) ions

2022 ◽  
Vol 0 (0) ◽  
Author(s):  
Md. Nabul Sardar ◽  
Nazia Rahman ◽  
Shahnaz Sultana ◽  
Nirmal Chandra Dafader
Keyword(s):  
Adsorption Capacity ◽  
Metal Ion ◽  
Aqueous Media ◽  
Thermo Gravimetric Analysis ◽  
Ion Concentration ◽  
Gravimetric Analysis ◽  
Order Kinetic ◽  
Polypropylene Fabric ◽  
Alternative Material ◽  
Waste Polypropylene

Abstract This study focuses on the adsorption of hazardous Cr (III) and Cu (II) ions from aqueous solution by applying modified waste polypropylene (PP) fabric as an adsorbent. Pre-irradiation technique was performed for grafting of sodium styrene sulfonate (SSS) and acrylic acid (AAc) onto the PP fabric. The monomer containing 8% SSS and 16% AAc in water was used. Graft yield at 30 kGy radiation dose was 390% when 4% NaCl was added as additive. The prepared adsorbent was characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), thermo-gravimetric analysis (TGA) and dynamic mechanical analyzer (DMA). The influences of different parameters including pH, contact time, temperature and initial metal ion concentration were also investigated. The equilibrium adsorption data were better fitted to the Langmuir isotherm model with maximum monolayer adsorption capacity 384.62 mg/g for Cr (III) and 188.68 mg/g for Cu (II) ions. The kinetic data were better explained by pseudo first-order kinetic model having good matching between the experimental and theoretical adsorption capacity. The adsorption process was spontaneous, endothermic and thermodynamically feasible. Furthermore, investigation of desorption of metal ions and reuse of the adsorbent suggesting that the adsorbent is an efficient and alternative material in the removal of Cr (III) and Cu (II) from aqueous media.

scholarly journals Comparative Study on the Adsorption Kinetics and Thermodynamics of Metal Ions onto Acid Activated Low Cost Pandanus Carbon

2007 ◽  
Vol 4 (2) ◽  
pp. 238-254 ◽  
Author(s):  
R. Sudha ◽  
K. Kalpana ◽  
T. Rajachandrasekar ◽  
S. Arivoli
Keyword(s):  
Metal Ions ◽  
Metal Ion ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Kinetic Studies ◽  
Ion Concentration ◽  
Effect Of Temperature ◽  
Ferrous Ions ◽  
Sem Images ◽  
Operating Variables

Batch experiments were carried out for the sorption of Copper and Ferrous ions onto acid activated carbon prepared. The operating variables studied were initial metal ion concentration, pH, and temperature and contact time. The equilibrium data were fitted to the Langmuir and Freundlich isotherm equations. From this adsorption efficiency, adsorption energy, adsorption capacity, intensity of adsorption and dimensionless separation factor were calculated. From the kinetic studies the rate constant values for the adsorption process was calculated. From the effect of temperature thermodynamic parameters like ΔG°, ΔH°, and ΔS° were calculated. The mechanism of adsorption for metal ions onto carbon was investigated by using the experimental results and confirmed by FT- IR, XRD and SEM images.

scholarly journals Heavy Metal Ion Adsorption Properties of Methacrylamidocysteine-Containing Porous Poly(Hydroxyethyl Methacrylate) Chelating Beads

2002 ◽  
Vol 20 (7) ◽  
pp. 607-617 ◽  
Author(s):  
Adil Denizli ◽  
Bora Garipcan ◽  
Sibel Emir ◽  
Süleyman Patir ◽  
Ridvan Say
Keyword(s):  
Heavy Metal ◽  
Metal Ions ◽  
Metal Ion ◽  
Heavy Metal Ions ◽  
Metal Removal ◽  
Ph Value ◽  
Heavy Metal Removal ◽  
Ion Concentration ◽  
Heavy Metal Ion ◽  
Adsorption Capacities

Details of the adsorption performance of poly(2-hydroxyethylmethacrylate–methacrylamidocysteine) [p(HEMA–MAC)] beads towards the removal of heavy metal ions from aqueous solution were studied. The metal-complexing ligand and/or co-monomer MAC was newly synthesized from methylacrylochloride and cysteine. Spherical beads of average size 150–200 mm were obtained by the radical suspension polymerization of MAC and HEMA conducted in an aqueous dispersion. The p(HEMA–MAC) beads obtained had a specific surface area of 18.9 m2/g. p(HEMA–MAC) beads were characterized by swelling studies, FT-IR spectroscopy and elemental analysis. Such beads with a swelling ratio of 72%, and containing 3.9 mmol MAC/g, were used for heavy metal removal studies. The adsorption capacities of the beads for selected metal ions, i.e. CdII, AsIII, CrIII, HgII and PbII, were investigated in aqueous media containing different amounts of these ions (10–750 mg/l) and at different pH values (3.0–7.0). The adsorption rate was fast in all cases. The maximum adsorption capacities of the p(HEMA–MAC) beads were 1058.2 mg/g for CdII, 123.4 mg/g for AsIII, 199.6 mg/g for CrIII, 639.1 mg/g for PbII and 1018.6 mg/g for HgII. On a molar basis, the following affinity order was observed: CdII > HgII > CrIII > PbII >AsIII. The adsorption capacity of the MAC-incorporated beads was affected significantly by the pH value of the aqueous medium. The adsorption of heavy metal ions from artificial wastewater was also studied. In this case, the adsorption capacities were 52.2 mg/g for CdII, 23.1 mg/g for CrIII, 83.4 mg/g for HgII, 62.6 mg/g for PbII and 11.1 mg/g for AsIII at an initial metal ion concentration of 0.5 mmol/l. The chelating beads could be regenerated easily with a higher effectiveness by 0.1 M HNO3. These features make p(HEMA–MAC) beads potential candidates for heavy metal ion removal at high capacity.

scholarly journals Sulfonated Magnetic Nanocomposite Based on Reactive PGMA-MAn Copolymer@Fe3O4 Nanoparticles: Effective Removal of Cu(II) Ions from Aqueous Solutions

2016 ◽  
Vol 2016 ◽  
pp. 1-15 ◽  
Author(s):  
Reza Hasanzadeh ◽  
Peyman Najafi Moghadam ◽  
Naeimeh Bahri-Laleh ◽  
Ehsan Nazarzadeh Zare
Keyword(s):  
Aqueous Solutions ◽  
Metal Ions ◽  
Metal Ion ◽  
Magnetic Nanocomposite ◽  
Ion Concentration ◽  
Gravimetric Analysis ◽  
X Ray ◽  
Equilibrium Distribution Coefficient ◽  
Effective Removal ◽  
Maleic Anhydride Copolymer

Chelating magnetic nanocomposites have been considered as suitable materials for removal of heavy metal ions for water treatment. In this work poly(glycidyl methacrylate-maleic anhydride) copolymer (PGMA-MAn) is modified with 4-aminobenzenesulfonic acid (ABSAc) and subsequently the product reacted with modified Fe3O4 nanoparticles and 1,2-ethanedithiol (EDT) in the presence of ultrasonic irradiation for preparation of tridimensional chelating magnetic nanocomposite. Synthesized magnetic nanocomposite was characterized by Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), X-ray diffraction analysis (XRD), vibrating sample magnetometer (VSM), energy dispersive X-ray analysis (EDX), elemental mapping analysis (EMA), Brunauer-Emmett-Teller (BET), and thermal gravimetric analysis (TGA). The adsorption behavior of Cu(II) ions was investigated by synthesized nanocomposite in various parameters such as pH, contact time, metal ion concentration, and adsorbent dosage. The equilibrium distribution coefficient (kd) was determined and the findings prove that the kd value is approximately high in the case of all selected metal ions. The synthesized nanocomposite exhibited good tendency for removing Cu(II) ions from aqueous solutions even at an acidic pH.

Use of agro-waste (Musa paradisiaca peels) as a sustainable biosorbent for toxic metal ions removal from contaminated water

2019 ◽  
Author(s):  
Chem Int
Keyword(s):  
Heavy Metal ◽  
Metal Ions ◽  
Contact Time ◽  
Metal Ion ◽  
Equilibrium Concentration ◽  
Ion Concentration ◽  
Contaminated Water ◽  
Musa Paradisiaca ◽  
Percentage Removal ◽  
Adsorbent Dose

A study of removal of heavy metal ions from heavy metal contaminated water using agro-waste was carried out with Musa paradisiaca peels as test adsorbent. The study was carried by adding known quantities of lead (II) ions and cadmium (II) ions each and respectively into specific volume of water and adding specific dose of the test adsorbent into the heavy metal ion solution, and the mixture was agitated for a specific period of time and then the concentration of the metal ion remaining in the solution was determined with Perkin Elmer Atomic absorption spectrophotometer model 2380. The effect of contact time, initial adsorbate concentration, adsorbent dose, pH and temperature were considered. From the effect of contact time results equilibrium concentration was established at 60minutes. The percentage removal of these metal ions studied, were all above 90%. Adsorption and percentage removal of Pb2+ and Cd2+ from their aqueous solutions were affected by change in initial metal ion concentration, adsorbent dose pH and temperature. Adsorption isotherm studies confirmed the adsorption of the metal ions on the test adsorbent with good mathematical fits into Langmuir and Freundlich adsorption isotherms. Regression correlation (R2) values of the isotherm plots are all positive (>0.9), which suggests too, that the adsorption fitted into the isotherms considered.

Efficient Preconcentration of Cu2+, Zn2+ and Fe3+ with an Agarose-Schiff Base Sorbent

2007 ◽  
Vol 72 (7) ◽  
pp. 908-916 ◽  
Author(s):  
Payman Hashemi ◽  
Hatam Hassanvand ◽  
Hossain Naeimi
Keyword(s):  
Schiff Base ◽  
Metal Ions ◽  
Metal Ion ◽  
Good Accuracy ◽  
Kinetic Studies ◽  
Sample Volume ◽  
Effects Of Ph ◽  
Glass Column ◽  
High Concentrations ◽  
Ph Range

Sorption and preconcentration of Cu2+, Zn2+ and Fe3+ on a salen-type Schiff base, 2,2'- [ethane-1,2-diylbis(nitrilomethylidyne)]bis(2-methylphenol), chemically immobilized on a highly crosslinked agarose support, were studied. Kinetic studies showed higher sorption rates of Cu2+ and Fe3+ in comparison with Zn2+. Half-times (t1/2) of 31, 106 and 58 s were obtained for sorption of Cu2+, Zn2+ and Fe3+ by the sorbent, respectively. Effects of pH, eluent concentration and volume, ionic strength, buffer concentration, sample volume and interferences on the recovery of the metal ions were investigated. A 5-ml portion of 0.4 M HCl solution was sufficient for quantitative elution of the metal ions from 0.5 ml of the sorbent packed in a 6.5 mm i.d. glass column. Quantitative recoveries were obtained in a pH range 5.5-6.5 for all the analytes. The volumes to be concentrated exceeding 500 ml, ionic strengths as high as 0.5 mol l-1, and acetate buffer concentrations up to 0.3 mol l-1 for Zn2+ and 0.4 mol l-1 for Cu2+ and Fe3+ did not have any significant effect on the recoveries. The system tolerated relatively high concentrations of diverse ions. Preconcentration factors up to 100 and detection limits of 0.31, 0.16 and 1.73 μg l-1 were obtained for Cu2+, Zn2+ and Fe3+, respectively, for their determination by a flame AAS instrument. The method was successfully applied to the metal ion determinations in several river water samples with good accuracy.

Separation of Heavy Metal Ions from the Solution Obtained by Leaching Low-Grade Pyrolusite with Pyrite and H2SO4

2013 ◽  
Vol 773 ◽  
pp. 283-288
Author(s):  
Xing Zou ◽  
Xiang Quan Chen ◽  
Hai Chao Xie ◽  
Xiao Dan Qiu
Keyword(s):  
Heavy Metal ◽  
Metal Ions ◽  
Heavy Metal Ions ◽  
Separation Efficiency ◽  
Ph Value ◽  
Sulfate Solution ◽  
Ion Concentration ◽  
Manganese Sulfate ◽  
Low Grade ◽  
High Concentration

The manganese sulfate solution leached from low-grade pyrolusite with pyrite and H2SO4 contains heavy metal ions of high concentration, influencing the quality of the final products of manganese compounds and causing manganese ions not to be electrolyzed. The present study was focused on the separation of Co, Ni and Zn ions from the leached solution with BaS. By controlling the pH value at 5.0-6.5, temperature at 50-60°C, reaction time at 15 min and mixing velocity at 78 rpm, the heavy metal ions could be separated effectively. Under the above optimized conditions, the ion concentration of Co, Ni, and Zn in the solution was reduced to 0.06 mg.L-1, 0.27mg.L-1 and 0.01mg.L-1, and the separation efficiency was 99.72%, 99.18% and 99.9% respectively. The obtained pure solution meets the demands of manganese electrowinning.

Membrane transport systems. II. Transport of alkali metal ions against their concentration gradients

1981 ◽  
Vol 59 (12) ◽  
pp. 1734-1744 ◽  
Author(s):  
Thomas M. Fyles ◽  
Virginia A. Malik-Diemer ◽  
Dennis M. Whitfield
Keyword(s):  
Alkali Metal ◽  
Metal Ions ◽  
Metal Ion ◽  
Complex Function ◽  
Membrane System ◽  
Ion Concentration ◽  
Transport Systems ◽  
Alkali Metal Ions ◽  
Concentration Gradients ◽  
Membrane Transport Systems

An artificial membrane system based on a series of macrocyclic polyether carriers (crown ethers) is described. Under the influence of a proton gradient the carriers move alkali metal ions from basic to acidic solution through a chloroform membrane phase. Transport occurs against the concentration gradient of the transported ion as a result of a coupled counterflow of protons. Different transport behaviors are observed depending upon the metal ion concentration. At high metal ion concentration the amount transported is a linear function of time; at lower metal ion concentration the amount transported is a complex function of time which may be described as the result of a pair of consecutive first order processes. Effects of metal ion, carrier, and proton concentration on transport rate are considered. The rate increases with increasing metal ion or carrier concentration but is essentially independent of the pH of either aqueous phase. Increased lipophilicity of the carrier also results in a rate increase. Carriers derived from 18-crown-6 transport potassium selectively and all ions more rapidly than 15-crown-5 derivatives which are, however, selective for sodium. The overall efficiency of the system is discussed in terms of competing "leak" reactions, either of cations from the basic phase or of anions from the acidic phase.

scholarly journals Equilibrium modeling of mono and binary sorption of Cu(II) and Zn(II) onto chitosan gel beads

2016 ◽  
Vol 37 (4) ◽  
pp. 485-501 ◽  
Author(s):  
Józef Nastaj ◽  
Małgorzata Tuligłowicz ◽  
Konrad Witkiewicz
Keyword(s):  
Metal Ion ◽  
Ph Value ◽  
Experimental Studies ◽  
Process Conditions ◽  
Optimal Process ◽  
Sorption Data ◽  
Gel Beads ◽  
Two Component ◽  
Equilibrium Data ◽  
Chitosan Gel

Abstract The objective of the work are in-depth experimental studies of Cu(II) and Zn(II) ion removal on chitosan gel beads from both one- and two-component water solutions at the temperature of 303 K. The optimal process conditions such as: pH value, dose of sorbent and contact time were determined. Based on the optimal process conditions, equilibrium and kinetic studies were carried out. The maximum sorption capacities equaled: 191.25 mg/g and 142.88 mg/g for Cu(II) and Zn(II) ions respectively, when the sorbent dose was 10 g/L and the pH of a solution was 5.0 for both heavy metal ions. One-component sorption equilibrium data were successfully presented for six of the most useful three-parameter equilibrium models: Langmuir-Freundlich, Redlich-Peterson, Sips, Koble-Corrigan, Hill and Toth. Extended forms of Langmuir-Freundlich, Koble-Corrigan and Sips models were also well fitted to the two-component equilibrium data obtained for different ratios of concentrations of Cu(II) and Zn(II) ions (1:1, 1:2, 2:1). Experimental sorption data were described by two kinetic models of the pseudo-first and pseudo-second order. Furthermore, an attempt to explain the mechanisms of the divalent metal ion sorption process on chitosan gel beads was undertaken.

scholarly journals STUDY OF REMOVAL OF METAL IONS IN WATER USING ZEOLITES SYNTHESIZED WITH CHARCOAL ASHES

2006 ◽  
Vol 05 (3) ◽  
pp. 21-30
Author(s):  
Denise Alves FUNGARO ◽  
Juliana de Carvalho IZIDORO
Keyword(s):  
Metal Ions ◽  
Metal Ion ◽  
Ion Selectivity ◽  
Coal Ash ◽  
Electroplating Effluent ◽  
Zeolitic Material ◽  
Equilibrium Data ◽  
Metal Ion Selectivity ◽  
Removal Of Metal ◽  
Removal Of Metal Ions

The capacity of synthesized zeolites from Brazilian coal ash for the removal of metal ions from aqueous solutions has been investigated. Equilibrium data obtained have been found to fit both the Langmuir and Freundlich adsorption isotherms. The zeolitic material prepared with coal ash from baghouse filter showed the highest removal efficiencies. The metal ion selectivity of this product was determined as: Pb2+ > Cd2+ > Cu2+ > Zn2+ > Ni2+. The maximum cation exchange capacities were between 32.9 and 246.9 mg g-1. Tests showed that the zeolitic material was suitable for removal of zinc from electroplating effluent.

Sign in / Sign up

Export Citation Format

Share Document