Improvement of existing nightsoil treatment plant for nitrogen removal

2004 ◽  
Vol 49 (5-6) ◽  
pp. 273-279
Author(s):  
B.S. Lim ◽  
J.U. Kim ◽  
H.D. Park
Keyword(s):  
Nitrogen Removal ◽  
Removal Rate ◽  
Treatment Plant ◽  
Second Step ◽  
Aeration Tank ◽  
Oxidation Ditch ◽  
Treatment Efficiency ◽  
Operation And Maintenance ◽  
One Year ◽  
Efficiency Rate

This study was performed to increase the treatment efficiency and to reduce operation and maintenance costs of the existing nightsoil treatment plant. The existing nightsoil plant was not established by the nitrogen removal process, and was operated ineffectively with deterioration of treatment efficiency rate, and according to the demand of many operators, the expenses of operation and maintenance have become excessive. Modified plant has been changed through two steps. The first step, liquid decayed tank using closed oxidation ditch is operated to increase retention time only for nitrification. The second step, modified liquid decayed tank including anoxic tank is operated, it has an excellent nitrogen removal rate. In first step, when HRT was increased from 10 days to 13 days in liquid decayed tank including aeration tank using closed oxidation ditch, TN concentration of effluent appeared below 51 mg/l less than discharge limit, 60 mg/L. In second step, when anoxic tank and oxic tank were installed, HRT has been increased to 13 days and 26 days, respectively. Then average TN concentration of effluent was detected less than 13 mg/L for over one year. The simple process modified the existing two processes resulted in the reduction of costs for operation and maintenance in the personnel, chemical, and filter change sphere.

scholarly journals Upflow packed bed Anammox reactor used in two-stage deammonification of sludge digester effluent

2018 ◽  
Vol 78 (9) ◽  
pp. 1843-1851 ◽  
Author(s):  
İ. Çelen-Erdem ◽  
E. S. Kurt ◽  
B. Bozçelik ◽  
B. Çallı
Keyword(s):  
Removal Efficiency ◽  
Nitrogen Removal ◽  
Municipal Wastewater ◽  
Removal Rate ◽  
Treatment Plant ◽  
Packed Bed ◽  
Municipal Wastewater Treatment ◽  
Two Stage ◽  
N Removal ◽  
Total Nitrogen Removal

Abstract The sludge digester effluent taken from a full scale municipal wastewater treatment plant (WWTP) in Istanbul, Turkey, was successfully deammonified using a laboratory scale two-stage partial nitritation (PN)/Anammox (A) process and a maximum nitrogen removal rate of 1.02 kg N/m3/d was achieved. In the PN reactor, 56.8 ± 4% of the influent NH4-N was oxidized to NO2-N and the effluent nitrate concentration was kept below 1 mg/L with 0.5–0.7 mg/L of dissolved oxygen and pH of 7.12 ± 12 at 24 ± 4°C. The effluent of the PN reactor was fed to an upflow packed bed Anammox reactor where high removal efficiency was achieved with NO2-N:NH4-N and NO3-N:NH4-N ratios of 1.32 ± 0.19:1 and 0.22 ± 0.10:1, respectively. The results show that NH4-N removal efficiency up to 98.7 ± 2.4% and total nitrogen removal of 87.7 ± 6.5% were achieved.

Total nitrogen removal from high-strength ammonia recycle stream using a single submerged attached growth bioreactor

2007 ◽  
Vol 55 (8-9) ◽  
pp. 59-65 ◽  
Author(s):  
A. Onnis-Hayden ◽  
P.B. Pedros ◽  
J. Reade
Keyword(s):  
Total Nitrogen ◽  
Nitrogen Removal ◽  
Removal Rate ◽  
Treatment Plant ◽  
High Strength ◽  
Nitrogen Loading ◽  
Digested Sludge ◽  
Attached Growth ◽  
Anaerobically Digested Sludge ◽  
Total Nitrogen Removal

An experimental study investigating the nitrogen removal efficiency from the recycle stream generated in the dewatering facility of the anaerobically digested sludge at the Deer Island wastewater treatment plant (WWTP) in Boston was conducted using a single submerged attached growth bioreactor (SAGB), designed for simultaneous nitrification and denitrification. The applied nitrogen loading to the reactor ranged from 0.7 to 2.27 kg-N/m3·d, and the corresponding total nitrogen (TN) removal rate ranged from 0.38 to 1.8 kg-N/m3·d. The observed nitrification rates varied from 0.42 kg-N/m3·d to 1.45 kg-N/m3·d with an ammonia load of 0.5 kg-N/m3·d and 1.8 kg-N/m3·d, respectively. An average nitrification efficiency of 91% was achieved throughout the experiment. Denitrification efficiency varied from 55%, obtained without any addition of carbon source, to 95% when methanol was added in order to obtain a methanol/nitrate ratio of about 3 kg methanol/kg NO3−-N.

Upgrading of Florence wastewater treatment plant: co-digestion and nitrogen autotrophic removal

2005 ◽  
Vol 52 (4) ◽  
pp. 9-17 ◽  
Author(s):  
S. Caffaz ◽  
R. Canziani ◽  
C. Lubello ◽  
D. Santianni
Keyword(s):  
Nitrogen Removal ◽  
Pilot Plant ◽  
Municipal Wastewater ◽  
Biogas Production ◽  
Removal Rate ◽  
Treatment Plant ◽  
Experimental Results ◽  
Septic Tank ◽  
Technical Solution ◽  
Nitrite Production

In recent years a completely autotrophic nitrogen removal process based on Anammox biomass has been tested in a few European countries in order to treat anaerobic supernatant and to increase the COD/N ratio in municipal wastewater. This work reports experimental results on a possible technical solution to upgrade the S. Colombano treatment plant which treats wastewater from the Florentine urban area. The idea is to use 50% of the volume of the anaerobic digester in order to treat external sewage sludge (as septic tank sludge) together with waste activated sludge and to treat the resulting effluent on a SHARON-ANAMMOX process in order to remove nitrogen from the anaerobic supernatant. Anaerobic co-digestion, tested in a 200 L pilot plant, enables low cost treatment of septic tank sludge and increases biogas production; however, it also increases the nitrogen load re-circulated to the WWTP, where nitrogen removal efficiency is already low (<50%), due to the low COD/N ratio, which limits predenitrification efficiency. Experimental results from a SHARON process tested in a lab-scale pilot plant show that nitrite oxidising bacteria are washed-out and steady nitrite production can be achieved at retention times in the range 1–1.5 days, at 35 °C. In a lab-scale SBR reactor, coupled with a nitration bioreactor, maximum specific nitrogen removal rate under nitrite-limiting conditions (with doubling time equal to about 26 days at 35 °C) was equal to 0.22 kgN/kgSSV/d, about 44 times the rate measured in inoculum Anammox sludge. Finally, a cost analysis of the proposed upgrade is reported.

Experience from start-ups of the first ANITA Mox Plants

2013 ◽  
Vol 67 (12) ◽  
pp. 2677-2684 ◽  
Author(s):  
M. Christensson ◽  
S. Ekström ◽  
A. Andersson Chan ◽  
E. Le Vaillant ◽  
R. Lemaire
Keyword(s):  
Nitrogen Removal ◽  
Removal Rate ◽  
Treatment Plant ◽  
Ammonia Removal ◽  
Nitrogen Loading ◽  
Biofilm Reactor ◽  
Process Conditions ◽  
N2o Emissions ◽  
N Removal ◽  
Start Up

ANITA™ Mox is a new one-stage deammonification Moving-Bed Biofilm Reactor (MBBR) developed for partial nitrification to nitrite and autotrophic N-removal from N-rich effluents. This deammonification process offers many advantages such as dramatically reduced oxygen requirements, no chemical oxygen demand requirement, lower sludge production, no pre-treatment or requirement of chemicals and thereby being an energy and cost efficient nitrogen removal process. An innovative seeding strategy, the ‘BioFarm concept’, has been developed in order to decrease the start-up time of new ANITA Mox installations. New ANITA Mox installations are started with typically 3–15% of the added carriers being from the ‘BioFarm’, with already established anammox biofilm, the rest being new carriers. The first ANITA Mox plant, started up in 2010 at Sjölunda wastewater treatment plant (WWTP) in Malmö, Sweden, proved this seeding concept, reaching an ammonium removal rate of 1.2 kgN/m3 d and approximately 90% ammonia removal within 4 months from start-up. This first ANITA Mox plant is also the BioFarm used for forthcoming installations. Typical features of this first installation were low energy consumption, 1.5 kW/NH4-N-removed, low N2O emissions, <1% of the reduced nitrogen and a very stable and robust process towards variations in loads and process conditions. The second ANITA Mox plant, started up at Sundets WWTP in Växjö, Sweden, reached full capacity with more than 90% ammonia removal within 2 months from start-up. By applying a nitrogen loading strategy to the reactor that matches the capacity of the seeding carriers, more than 80% nitrogen removal could be obtained throughout the start-up period.

An Experimental Study on Compatible Solute Ectoine Dosing of High Salinity Wastewater

2014 ◽  
Vol 955-959 ◽  
pp. 1907-1910
Author(s):  
Su Chen ◽  
Lei Chao ◽  
Ning Chen ◽  
Lin Shan Wang ◽  
Xue Shao ◽  
...  
Keyword(s):  
Nitrogen Removal ◽  
Waste Treatment ◽  
High Salinity ◽  
Removal Rate ◽  
Ammonia Nitrogen ◽  
Ammonium Nitrogen ◽  
Treatment Efficiency ◽  
Removal Rates ◽  
Cod Removal Rate ◽  
Salinity Wastewater

When the reactor is added with ectoine of concentrations of 0, 0.1, 1 and 10 mmol/L, the impacts on brine waste treatment efficiency are investigated. The results show that the outflow COD and ammonia nitrogen removal rates are the highest, when the ectoine concentration is 0.1 mmol/L. The brine waste treatment efficiency under addition of ectoine of 1 and 10 mmol/L is even worse than that without ectoine addition. It can be preliminarily determined that the best ectoine dosage is in between 0.1-1.0 mmol/L. When ectoine concentrations added in reactors are 0.2, 0.5, 0.8 and 1.0 mmol/L, the results show that the average reactor outflow COD and ammonia nitrogen removal rates are increased compared with those of reactor without adding ectoine. But when ectoine of 1.0 mmol/L is added, the outflow COD and ammonia nitrogen removal rates decrease. When ectoine dosage is 0.5 mmol/L, the reactor outflow COD and ammonia nitrogen values are the lowest, the removal rates are the highest, the average COD removal rate is 74.46%, and the average ammonium nitrogen removal rate is 54.97%. Compared with reactor without adding ectoine, COD and ammonium nitrogen removal rates are increased by 13.16% and 26.81%. Therefore, the best dosage of ectoine is 0.5 mmol/L.

Dewatering and Mineralization of Sludge from Secondary Sedimentation Tank in a Constructed Sludge Drying Reed Bed

2012 ◽  
Vol 209-211 ◽  
pp. 1111-1115
Author(s):  
Chun Zhang ◽  
Jie Deng ◽  
Wei Zhang
Keyword(s):  
Heavy Metals ◽  
Removal Rate ◽  
Treatment Plant ◽  
Oxygen Demand ◽  
Bottom Layer ◽  
Heavy Metal Concentration ◽  
The European Union ◽  
Sedimentation Tank ◽  
Reed Bed ◽  
One Year

The dewatering and mineralization of sludge in the constructed reed bed was investigated in this study.The sludge from the secondary sedimentation tank is from in the wastewater treatment plant in Yiyang city,Hunan province.Anaerobic pond and oxidation ditch biological treatment processes is accepted there.The performance of the system was monitored for one year. Total Solids (TS), Volatile Solids(VS), Chemical Oxygen Demand, nutrients (TKN) and Total Phosphorus(TP), heavy metals in the sludge were analysed.The removal rate of COD,NH4-N,and TP of the percolated fluid for the first cycle was also monitored. TS content reached 36.5% for the surface layer and 37.8% for the bottom layer at the end of the examination period.Sludge stabilization in the bed was also observed(VS content decreased to 31.3% and 13.4% respectively for the surface and bottom layer).Concentration of nutrients of the sludge accumulated in the bed also decreased. The heavy metal concentration meets the European Union standards for heavy metals in case of agricultural disposal of the treated sludge.

SUSTAINABLE NITROGEN REMOVAL USING APPROPRIATE TECHNOLOGIES

2017 ◽  
Vol 4 (1) ◽  
Author(s):  
Krishnanand Maillacheruvu ◽  
Derek Hartmann
Keyword(s):  
Rate Constant ◽  
Nitrogen Removal ◽  
Removal Rate ◽  
Low Cost ◽  
C:N Ratio ◽  
Treatment Plant ◽  
Agricultural Runoff ◽  
Point Sources ◽  
Nitrogen And Phosphorus ◽  
N Removal

Nitrogen and phosphorus are two major pollutants that lead to eutrophication, adversely impact ecosystems, and lead to degradation of water quality, which impacts human health and sustainability. Pollution from point sources like wastewater and industry discharge is easier to control than non-point source pollution due to agricultural runoff and related activities. The USEPA is considering more strict standards for nitrogen and phosphorus discharge from point sources. The objective of this study was to use an appropriate low-cost wastewater technology to demonstrate removal of nitrogen from wastewater discharge using rotating biological contactors (RBCs) using different C:N ratios. The first-order nitrogen removal rate constant was found to be about 3.88 day-1 in experimental reactor systems, using RBC media from a local wastewater treatment plant (Greater Peoria Sanitary District). Phase I experiments, at C:N ratio of 2:1, with nitrogen removal rates of 60% in a single flow-through system. Phase II experiments for the limited carbon availability condition showed that the removal rate constant reduced by 30% and N-removal efficiency dropped to around 48%. Modeling showed that even under these conditions, multiple bioreactors operated in series could help achieve design treatment goals. The system achieved stability within a week of operation. Economics and sustainability issues are analyzed to determine if the process developed in this research is scalable to pilot-and full-scale conditions.

scholarly journals Start-up of a full-scale partial nitritation-anammox MBBR without inoculum at Klagshamn WWTP

2020 ◽  
Vol 81 (9) ◽  
pp. 2033-2042 ◽  
Author(s):  
Ivelina Dimitrova ◽  
Agnieszka Dabrowska ◽  
Sara Ekström
Keyword(s):  
Nitrogen Removal ◽  
Removal Rate ◽  
Treatment Plant ◽  
Full Scale ◽  
Biofilm Reactor ◽  
Operating Conditions ◽  
Ex Situ ◽  
Ammonium Oxidation ◽  
Partial Nitritation ◽  
Start Up

Abstract Partial nitritation and anaerobic ammonium oxidation (PNA) is a useful process for the treatment of nitrogen-rich centrate from the dewatering of anaerobically digested sludge. A one-stage PNA moving bed biofilm reactor (MBBR) was started up without inoculum at Klagshamn wastewater treatment plant, southern Sweden. The reactor was designed to treat up to 200 kgN d−1, and heated dilution water was used during start-up. The nitrogen removal was >80% after 111 days of operation, and the nitrogen removal rate reached 1.8 gN m−2 d1 at 35 °C. The start-up period of the reactor was comparable to that of inoculated full-scale systems. The operating conditions of the system were found to be important, and online control of the free ammonia concentration played a crucial role. Ex situ batch activity tests were performed to evaluate process performance.

Aeration tank settling and real time control as a tool to improve the hydraulic capacity and treatment efficiency during wet weather: results from 7 years' full-scale operational data

2013 ◽  
Vol 67 (10) ◽  
pp. 2169-2176 ◽  
Author(s):  
A. K. Sharma ◽  
T. Guildal ◽  
H. A. R. Thomsen ◽  
P. S. Mikkelsen ◽  
B. N. Jacobsen
Keyword(s):  
Real Time ◽  
Treatment Plant ◽  
Aeration Tank ◽  
Treatment Efficiency ◽  
Real Time Control ◽  
Design Capacity ◽  
Time Control ◽  
Wet Weather ◽  
Operational Data ◽  
Tank Settling

This paper investigates the aeration tank settling (ATS) operation in combination with real time control (RTC) as a tool for increasing the hydraulic capacity and improving the treatment efficiency of a wastewater treatment plant (WWTP) during wet weather flows. Results from 7 years' full-scale operational data at the Avedøre WWTP, Denmark, show that ATS operation in combination with RTC increases the hydraulic capacity of the treatment plant with up to 150 and 67% of the design capacity during winter and summer respectively. Compared to the conventional wet weather operation, the ATS in combination with RTC operation resulted in lower effluent concentrations for total phosphate (40–50%), suspended solids (30–60%) and chemical oxygen demand (30–50%), whereas no significant effect was observed on total nitrogen. Apart from the reduced effluent concentrations, the RTC resulted in economic savings in the form of reduced costs for electricity and green taxes. However, in very few cases the ATS operation in combination with RTC was not able to handle design capacity, and some overflows occurred at flows below the design capacity. The frequency of these overflows may increase in the future due to increased rain intensity resulting in shorter prediction time available for ATS.

The Operating Characteristics of Orbal Oxidation Ditch Process under Low Dissolved Oxygen

2013 ◽  
Vol 328 ◽  
pp. 297-303
Author(s):  
Si Mei Zhang ◽  
Lu Liu ◽  
Shu Heng Hu
Keyword(s):  
Dissolved Oxygen ◽  
Removal Rate ◽  
Sewage Treatment ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Oxidation Ditch ◽  
Operating Characteristics ◽  
Low Dissolved Oxygen ◽  
N Removal ◽  
Orbal Oxidation Ditch

Orbal oxidation ditch is widely used in urban sewage treatment system ,Oxygen consumption level is an important index to measure process operating characteristic, discuss the operation mode of Oxidation ditch under low dissolved oxygen concentration condition is the main link of Sewage plants energy saving operation. Through the adjustment of chongqing TongLiang sewage treatment plant Orbal oxidation ditch aerations equipment operation parameters, the operating power reduced 7.5 kW, the removal rate of TN increased from 19% to more than 50%,and COD, BOD5, TP, NH3 - N removal rate was not affected, the Water meet the design requirements.

Sign in / Sign up

Export Citation Format

Share Document