scholarly journals Removal of atenolol from aqueous solutions by multiwalled carbon nanotubes modified with ozone: kinetic and equilibrium study

2018 ◽  
Vol 2017 (3) ◽  
pp. 636-649 ◽  
Author(s):  
Bahare Dehdashti ◽  
Mohammad Mehdi Amin ◽  
Hamidreza Pourzamani ◽  
Lida Rafati ◽  
Mehdi Mokhtari
Keyword(s):  
Carbon Nanotubes ◽  
Aqueous Solutions ◽  
Multiwalled Carbon Nanotubes ◽  
Removal Efficiency ◽  
Contact Time ◽  
Maximum Adsorption Capacity ◽  
Multiwall Carbon Nanotube ◽  
Multiwalled Carbon ◽  
Initial Concentration ◽  
Multiwall Carbon

Abstract The aim of study is removal of atenolol from aqueous solutions by multiwalled carbon nanotubes modified with ozone. The design of the experiment was adopted across four levels with the L16 matrix arrangement. The factors influencing atenolol adsorption include changes in the pH value, contact time, the dose of the modified multiwall carbon nanotube, and the initial concentration of atenolol in the solution; these factors were evaluated along with the extent of their influence on removal efficiency. Data analyses were performed by the Design Expert 6 software. The results indicated that the pH, contact time, adsorbent dose, and the initial concentration were 7, 20 min, 0.15 g/L and 1 mg/L, respectively. In this state, the removal efficiency was calculated to be 75.79%. The maximum adsorption capacity was obtained as 5.05 mg/g under optimal conditions. The data were analyzed using adsorption models obtained from the isotherm fitting tool software. The results suggested that the data had a greater congruence with the Freundlich model (corrected Akaike information criterion = 2.58). Furthermore, the kinetics of the reactions followed pseudo second order kinetics (R2 = 0.95). Based on this study, it can be concluded that modified multiwall carbon nanotubes enjoy high potential and efficiency as adsorbents for the removal of atenolol from aqueous solutions.

Sorption of Bisphenol A in Aqueous Solutions on Irradiated and as-Grown Multiwalled Carbon Nanotubes

2018 ◽  
Vol 69 (5) ◽  
pp. 1233-1239
Author(s):  
Raluca Madalina Senin ◽  
Ion Ion ◽  
Ovidiu Oprea ◽  
Rusandica Stoica ◽  
Rodica Ganea ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Bisphenol A ◽  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Multiwalled Carbon Nanotubes ◽  
Adsorption Process ◽  
Sorption Process ◽  
Multiwalled Carbon ◽  
Before And After ◽  
Kinetic Sorption

In this study, non-irradiated and weathered multiwalled carbon nanotubes (MWCNTs) obtained through irradiation, were studied as adsorbents for BPA, both nanomaterials being characterized before and after the adsorption process. The objectives of our investigation were to compare the characteristics of non-irradiated and irradiated MWCNTs, to evaluate the adsorption capacity of BPA by pristine and irradiated MWCNTs and to determine the variation of the kinetic, sorption and thermodynamic parameters during sorption process using both sorbents.

Preparation and Application of Electrospinning Membranes of Thermoplastic Carboxymethyl Cellulose/PLA for Removal of Cu2+ from Aqueous Solutions

2012 ◽  
Vol 724 ◽  
pp. 61-64
Author(s):  
Ying Li ◽  
Xiao Yan Lin ◽  
Zhe Chen ◽  
Xue Guang Luo ◽  
Wei Li Zuo
Keyword(s):  
Tensile Strength ◽  
Aqueous Solutions ◽  
Removal Efficiency ◽  
Composite Membrane ◽  
Carboxymethyl Cellulose ◽  
Contact Time ◽  
Electrospinning Process ◽  
Cross Linking ◽  
Initial Concentration ◽  
The Cross

A composite membrane of thermoplastic carboxymethyl cellulose (TCMC) /PLA was prepared by electrospinning process, and crossliked by epichlorohydrin solution at different temperature. The cross-linking temperature was optimized by characterizing the morphology and tensile strength of the film. The optimal cross-linking temperature was 50°C. A composite membrane was used to remove Cu2+ from aqueous solutions, and the effects of initial concentration of Cu2+ and contact time on the removal efficiency of Cu2+ were investigated. The removal efficiency of Cu2+ was 13.78%, at the initial concentration of 40 mg·L-1 and contact time of 30s.

Removal of iron and manganese from aqueous solutions using carbon nanotube filters

2015 ◽  
Vol 16 (2) ◽  
pp. 347-353 ◽  
Author(s):  
E. M. I. Elsehly ◽  
N. G. Chechenin ◽  
K. A. Bukunov ◽  
A. V. Makunin ◽  
A. B. Priselkova ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Aqueous Solution ◽  
Aqueous Solutions ◽  
Removal Efficiency ◽  
Metal Ion ◽  
Diameter Distribution ◽  
Outer Diameter ◽  
Multiwalled Carbon ◽  
Metal Ion Removal ◽  
Heavy Metal Ion Removal

Carbon nanotubes (CNTs) have become the focus of attention of many scientists and companies worldwide. CNT-based filters have a prospective advantage in comparison to the commercial filters already in operation because they are light weight and do not require electricity to operate. This investigation handles the filtration efficiency of manganese and iron from aqueous solution using commercial multiwalled carbon nanotubes (MWCNTs) (Taunit). The effects of different parameters such as CNT filter mass, concentration of manganese and iron in aqueous solution and pH of aqueous solution on removal of these heavy metals are determined. From these investigations, the removal efficiency of manganese and iron could reach 71.5% and 52% respectively for concentration 50 ppm, suggesting that Taunit is an excellent adsorbent for manganese and iron removal from water. There was a significant increase in removal efficiency at pH = 3 for manganese and pH = 8 for iron. The effect of oxidation on the structural of MWCNTs was characterized by scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) techniques to investigate the functionalization with oxygen-containing and outer diameter distribution. It was found that functionalized CNT-based filters are more efficient at removing manganese and iron from aqueous solutions. Oxidized MWCNTs may be a promising candidate for heavy metal ion removal from industrial wastewater.

scholarly journals Adsorption of Nickel and Chromium From Aqueous Solutions Using Copper Oxide Nanoparticles: Adsorption Isotherms, Kinetic Modeling, and Thermodynamic Studies

2019 ◽  
Vol 6 (2) ◽  
pp. 66-74 ◽  
Author(s):  
Raziyeh Hosseini ◽  
Mohammad Hossein Sayadi ◽  
Hossein Shekari
Keyword(s):  
Aqueous Solutions ◽  
Copper Oxide ◽  
Removal Efficiency ◽  
Contact Time ◽  
Removal Rate ◽  
Copper Oxide Nanoparticles ◽  
Isotherm Models ◽  
Oxide Nanoparticles ◽  
Initial Concentration ◽  
Adsorbent Dosage

The research was conducted with an aim to assess the efficiency of copper oxide nanoparticles as an adsorbent to remove Ni and Cr. The effect of pH, adsorbent dosage, contact time, initial concentration of metals (Ni and Cr) on the adsorption rate was evaluated and removal of these elements from aqueous solutions was measured using Atomic Absorption Spectrum System (Conter AA700). Moreover, the kinetic and isotherm besides thermodynamic adsorption models were assessed. The highest Ni and Cr removal rate occurred at an optimal pH of 7, and an initial concentration of 30 mg/L, a time period of 30 minutes, and 1 g/L of copper oxide nanoparticles. In fact, with the increase of adsorbent dosage and contact time, the removal efficiency increased and with initial concentration increase of Ni and Cr ions, the removal efficiency reduced. The correlation coefficient of isotherm models viz. Langmuir, Freundlich, Temkin, Redlich-Peterson, and Koble-Corrigan showed that Ni and Cr adsorption via copper oxide nanoparticles better follows the Langmuir model in relation to other models. The results showed that kinetic adsorption of Ni and Cr via copper oxide nanoparticles follows the second order pseudo model with correlation coefficients above 0.99. In addition, the achieved thermodynamic constants revealed that the adsorption process of metals (i.e., Ni and Cr) via copper oxide nanoparticles was endothermic and spontaneous and the reaction enthalpy values for these metals were 17.727 and 11.862 kJ/mol, respectively. In conclusion, copper oxide nanoparticles can be used as effective and environmentally compatible adsorbents to remove Ni and Cr ions from the aqueous solutions

scholarly journals Investigating the efficiency of single-walled and multi-walled carbon nanotubes in removal of penicillin G from aqueous solutions

2018 ◽  
Vol 5 (4) ◽  
pp. 187-196 ◽  
Author(s):  
Soheila Chavoshan ◽  
Maryam Khodadadi ◽  
Negin Nasseh ◽  
Ayat Hossein Panahi ◽  
Aliyeh Hosseinnejad
Keyword(s):  
Carbon Nanotubes ◽  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Langmuir Model ◽  
Penicillin G ◽  
Maximum Adsorption Capacity ◽  
Initial Concentration ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes ◽  
Kinetics Of

Background: Drugs, especially antibiotics, are one of the serious problems of modern life and the main pollution sources of the environment, especially in the last decade, which are harmful to human health and environment. The aim of this study was to investigate the removal of penicillin G from aqueous solutions using single-walled and multi-walled carbon nanotubes. Methods: In this study, the effect of different parameters including pH (3, 5, 7, 9, and 11), initial concentration of pollutant (50, 100, 150, and 200 mg/l), absorbent dose (0.25, 0.5, 0.75, and 1 g/L), mixing speed (0, 100, 200, and 300 rpm), and temperature (10, 15, 25, 35, 45°C) were investigated. The Langmuir, Freundlich, Temkin, BET, Dubinin-Radushkevich isotherms and adsorption kinetics of the first- and second-order equations were determined. Results: The results showed that the efficiency of single-walled and multi-walled carbon nanotubes in the removal of penicillin G was 68.25% and 56.37%, respectively, and adsorption capacity of the nanotubes was 141 mg/g and 119 mg/g at initial concentration of 50 mg/l and pH=5 with adsorption dose of 0.8 g/L for 105 minutes at 300 rpm and temperature of 10°C from aqueous solutions. Also, it was revealed that the adsorption process had the highest correlation with the Langmuir model and secondorder kinetics, and the maximum adsorption capacity based on Langmuir model was 373.80 mg/g. Conclusion: According to the results, it was found that single-walled and multi-walled carbon nanotubes can be used as effective absorbents in the removal of penicillin G from aqueous solutions.

scholarly journals Comparing the Adsorption Performance of Multiwalled Carbon Nanotubes Oxidized by Varying Degrees for Removal of Low Levels of Copper, Nickel and Chromium(VI) from Aqueous Solutions

Water ◽  
2020 ◽  
Vol 12 (3) ◽  
pp. 723 ◽  
Author(s):  
Marko Šolić ◽  
Snežana Maletić ◽  
Marijana Kragulj Isakovski ◽  
Jasmina Nikić ◽  
Malcolm Watson ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Carbon Nanotubes ◽  
Aqueous Solutions ◽  
Multiwalled Carbon Nanotubes ◽  
Electrostatic Interactions ◽  
Positive Impact ◽  
Molar Ratio ◽  
Multiwalled Carbon ◽  
Removal Of Heavy Metals ◽  
Low Levels

Functionalized multiwalled carbon nanotubes (MWCNTs) have drawn wide attention in recent years as novel materials for the removal of heavy metals from the aquatic media. This paper investigates the effect that the functionalization (oxidation) process duration time (3 h or 6 h) has on the ability of MWCNTs to treat water contaminated with low levels of Cu(II), Ni(II) and Cr(VI) (initial concentrations 0.5–5 mg L−1) and elucidates the adsorption mechanisms involved. Adsorbent characterization showed that the molar ratio of C and O in these materials was slightly lower for the oxMWCNT6h, due to the higher degree of oxidation, but the specific surface areas and mesopore volumes of these materials were very similar, suggesting that prolonging the functionalization duration had an insignificant effect on the physical characteristics of oxidized multiwalled carbon nanotubes (oxMWCNTs). Increasing the Ph of the solutions from Ph 2 to Ph 8 had a large positive impact on the removal of Cu(II) and Ni(II) by oxMWCNT, but reduced the adsorption of Cr(VI). However, the ionic strength of the solutions had far less pronounced effects. Coupled with the results of fitting the kinetics data to the Elowich and Weber–Morris models, we conclude that adsorption of Cu(II) and Ni(II) is largely driven by electrostatic interactions and surface complexation at the interface of the adsorbate/adsorbent system, whereas the slower adsorption of Cr(VI) on the oxMWCNTs investigated is controlled by an additional chemisorption step where Cr(VI) is reduced to Cr(III). Both oxMWCNT3h and oxMWCNT6h have high adsorption affinities for the heavy metals investigated, with adsorption capacities (expressed by the Freundlich coefficient KF) ranging from 1.24 to 13.2 (mg g−1)/(mg l−1)n, highlighting the great potential such adsorbents have in the removal of heavy metals from aqueous solutions.

Sign in / Sign up

Export Citation Format

Share Document