scholarly journals High Electric Production by Membraneless Microbial Fuel Cell with Up Flow Operation Using Acetate Wastewater

2020 ◽  
Vol 11 (2) ◽  
pp. 19-27
Author(s):  
Aris Mukimin ◽  
Nur Zen ◽  
Hanny Vistanty ◽  
Purwanto Agus
Keyword(s):  
Fuel Cell ◽  
Microbial Fuel Cell ◽  
Oxygen Demand ◽  
Gas Diffusion ◽  
Synthetic Wastewater ◽  
Anaerobic Sludge ◽  
Carbon Cloth ◽  
Current Response ◽  
Current Voltage ◽  
Anaerobic Chamber

Microbial fuel cell (MFC) is a new proposed technology reported to generate renewable energy while simultaneously treating wastewater. Membraneless microbial fuel cell (ML-MFC) system was developed to eliminate the requirement of membrane which is expensive and prone to clogging while enhancing electricity generation and wastewater treatment efficiency. For this purpose, a reactor was designed in two chambers and connected via three pipes (1 cm in diameter) to enhance fluid diffusion. Influent flowrate was maintained by adjusting peristaltic pump at the base of anaerobic chamber. Carbon cloth (235 cm2) was used as anode and paired with gas diffusion layer (GDL) carbon-Pt as cathode. Anaerobic sludge was filtered and used as starter feed for the anaerobic chamber. The experiment was carried out by feeding synthetic wastewater to anaerobic chamber; while current response and potential were recorded. Performance of reactor was evaluated in terms of chemical oxygen demand (COD). Electroactive microbe was inoculated from anaerobic sludge and showed current response (0.55-0.65 mA) at 0,35 V, range of diameter 1.5-2 µm. The result of microscopics can showed three different species. The microbial performance was increased by adding ferric oxide 1 mM addition as acceptor electron. The reactor was able to generate current, voltage, and electricity power of 0.36 mA, 110 mV, and 40 mWatt (1.5 Watt/m2), respectively, while reaching COD removal and maximum coulomb efficiency (EC) of 16% and 10.18%, respectively.

Simultaneous sewage treatment and electricity generation in membrane-less microbial fuel cell

2008 ◽  
Vol 58 (1) ◽  
pp. 37-43 ◽  
Author(s):  
M. M. Ghangrekar ◽  
V. B. Shinde
Keyword(s):  
Fuel Cell ◽  
Microbial Fuel Cell ◽  
Sewage Treatment ◽  
Oxygen Demand ◽  
Synthetic Wastewater ◽  
Septic Tank ◽  
Anaerobic Sludge ◽  
Anode Chamber ◽  
Maximum Current ◽  
Term Performance

Long term performance of mediator-less and membrane-less microbial fuel cell (ML-MFC) was evaluated for treatment of synthetic and actual sewage and electricity harvesting. The anode chamber of ML-MFC was inoculated with pre-heated mixed anaerobic sludge collected from a septic tank. The ML-MFC was operated by feeding synthetic wastewater for first 244 days, under different organic loading rates, and later with actual sewage for next 30 days. Maximum chemical oxygen demand (COD) removal efficiency of 91.4% and 82.7% was achieved while treating synthetic wastewater and actual sewage, respectively. Maximum current of 0.33 mA and 0.17 mA was produced during synthetic and actual sewage treatment, respectively. Maximum power density of 6.73 mW/m2 (13.65 mW/m3) and maximum current density of 70.74 mA/m2 was obtained in this membrane-less MFC with successful organic matter removal from wastewater.

scholarly journals The Membrane-Less Microbial Fuel Cell (ML-MFC) with Ni-Co and Cu-B Cathode Powered by the Process Wastewater from Yeast Production

Energies ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3976
Author(s):  
Barbara Włodarczyk ◽  
Paweł P. Włodarczyk
Keyword(s):  
Fuel Cell ◽  
Microbial Fuel Cell ◽  
Oxygen Demand ◽  
Complete Removal ◽  
Electricity Production ◽  
Carbon Cloth ◽  
Carbon Electrode ◽  
Yeast Production ◽  
Process Wastewater ◽  
Measurement Period

Research related to measurements of electricity production was combined with parallel wastewater parameter reduction in a membrane-less microbial fuel cell (ML-MFC) fed with industry process wastewater (from a yeast factory). Electrodes with Ni–Co and Cu–B catalysts were used as cathodes. A carbon electrode (carbon cloth) was used as a reference due to its widespread use. It was demonstrated that all analyzed electrodes could be employed as cathodes in ML-MFC fed with process wastewater from yeast production. Electricity measurements during ML-MFC operations indicated that power (6.19 mW) and current density (0.38 mA·cm−2) were the highest for Ni–Co electrodes. In addition, during the exploitation of ML-MFC, it was recorded that the chemical oxygen demand (COD) removal per time for all types of electrodes was similar to the duration of COD decrease in the conditions for wastewater aeration. However, the COD reduction curve for aeration took the most favorable course. The concentration of NH4+ in ML-MFC remained virtually constant throughout the measurement period, whereas NO3− levels indicated almost complete removal (with a minimum increase in the last days of cell exploitation).

Simultaneous carbon and nitrogen removal using a litre-scale upflow microbial fuel cell

2013 ◽  
Vol 69 (2) ◽  
pp. 293-297 ◽  
Author(s):  
Ling-ling Zhao ◽  
Tian-shun Song
Keyword(s):  
Fuel Cell ◽  
Microbial Fuel Cell ◽  
Nitrogen Removal ◽  
Microbial Fuel Cells ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Chicken Manure ◽  
Synthetic Wastewater ◽  
Nitrification Rate ◽  
Carbon And Nitrogen

A 10 L upflow microbial fuel cell (UMFC) was constructed for simultaneous carbon and nitrogen removal. During the 6-month operation, the UMFC constantly removed carbon and nitrogen, and then generated electricity with synthetic wastewater as substrate. At 5.0 mg L−1 dissolved oxygen, 100 Ω external resistance, and pH 6.5, the maximum power density (Pmax) and nitrification rate for the UMFC was 19.5 mW m−2 and 17.9 mg·(L d)−1, respectively. In addition, Pmax in the UMFC with chicken manure wastewater as substrate was 16 mW m−2, and a high chemical oxygen demand (COD) removal efficiency of 94.1% in the UMFC was achieved at 50 mM phosphate-buffered saline. Almost all ammonia in the cathode effluent was effectively degraded after biological denitrification in the UMFC cathode. The results can help to further develop pilot-scale microbial fuel cells for simultaneous carbon and nitrogen removal.

scholarly journals The Energy Production and Efficiency Treatment of ML-MFC Using High Organic Content Wastewater

2020 ◽  
Vol 202 ◽  
pp. 10006
Author(s):  
Aris Mukimin
Keyword(s):  
Fuel Cell ◽  
Microbial Fuel Cell ◽  
Flow Rate ◽  
Gas Diffusion ◽  
Organic Content ◽  
Carbon Cloth ◽  
Complex Character ◽  
Before And After ◽  
Current Production ◽  
High Organic Content

Microbial fuel cell (MFC) is a technology that is not only able to produce energy but also treats wastewater. The membraneless microbial fuel cell (ML-MFC) system was developed to avoid the use of membranes that are prone to clogging and are less applicable. The reactor was made and arranged in two chambers connected by pipes and the fluid flow rate is set using a peristaltic pump. Three anodes (carbon cloth) were paired with a carbon-Pt cathode GDL (Gas Diffusion Layer) type. The reactor was applied to wastewater taken from the industrial WWTP unit at the point before and after UASB. ML-MFC reactors can produce currents of 0.2 mA (before UASB) and 0.25 mA (after UASB). Current production is strongly influenced by the flow rate and characteristics of wastewater. Increased flow rates and complex character of wastewater will reduce current production. The electric power produced is 0.035 mwatt for wastewater before UASB and 0.086 mwatt after UASB with a COD removal is close to the same, which is 21% at a flow rate of 11 L / min1

scholarly journals Bioelectricity generation in annulus structure of single chamber membrane-less microbial fuel cell using wastewater from chocolate industry

2017 ◽  
Author(s):  
Ghasem Najafpour ◽  
Parisa Nouri ◽  
Mostafa Rahimnejad
Keyword(s):  
Wastewater Treatment ◽  
Fuel Cell ◽  
Microbial Fuel Cell ◽  
Power Density ◽  
Proton Exchange ◽  
Anaerobic Sludge ◽  
Carbon Cloth ◽  
Efficient System ◽  
Single Chamber ◽  
Chocolate Industry

Microbial Fuel Cell (MFC) is an efficient system for generating low power where wastewater is substrate for the biocatalyst. In this work, Annular Single Chamber Microbial Fuel Cell (ASCMFC) with spiral anode was fabricated and tested. Carbon cloth and stainless steel 400 meshes were selected as cathode and anode electrodes, respectively. In order to enhance the conductivity of anode, the graphite coating was applied. A 40% platinum as catalyst was used on carbon based cathode in MFC. The carbon cloth was coated with 5% Nafion solution. In fact Nafion acts as Proton Exchange Membrane (PEM) in the fabricated MFC. For the first time, wastewater of Chocolate industry with COD 1400 mg/L was used as substrate in anode compartment. Also a mixture of anaerobic sludge from wastewater treatment plant (Qaem-Shahr, Iran) was introduced into MFC. Maximum voltage obtained in the ASCMFC system was 792 mV in an open-circuit mode. Also, Fabricated MFC operating at 30 ◦C, the maximum achieved power density using an external resistance of 500Ω was about 4.8 W/m3. The upshots from single chamber MFC were compared to dual chamber MFC. The findings demonstrate that, due to the generated high power density and voltage by the cell, the ASCMFC has a great potential for COD removal and wastewater treatment.

scholarly journals The Energy Production and Efficiency Treatment of ML-MFC Using High Organic Content Wastewater

2020 ◽  
Vol 202 ◽  
pp. 10005
Author(s):  
Aris Mukimin
Keyword(s):  
Fuel Cell ◽  
Microbial Fuel Cell ◽  
Flow Rate ◽  
Gas Diffusion ◽  
Organic Content ◽  
Carbon Cloth ◽  
Complex Character ◽  
Before And After ◽  
Current Production ◽  
High Organic Content

Microbial fuel cell (MFC) is a technology that is not only able to produce energy but also treats wastewater. The membraneless microbial fuel cell (ML-MFC) system was developed to avoid the use of membranes that are prone to clogging and are less applicable. The reactor was made and arranged in two chambers connected by pipes and the fluid flow rate is set using a peristaltic pump. Three anodes (carbon cloth) were paired with a carbon-Pt cathode GDL (Gas Diffusion Layer) type. The reactor was applied to wastewater taken from the industrial WWTP unit at the point before and after UASB. ML-MFC reactors can produce currents of 0.2 mA (before UASB) and 0.25 mA (after UASB). Current production is strongly influenced by the flow rate and characteristics of wastewater. Increased flow rates and complex character of wastewater will reduce current production. The electric power produced is 0.035 mwatt for wastewater before UASB and 0.086 mwatt after UASB with a COD removal is close to the same, which is 21% at a flow rate of 11 L / min1

scholarly journals Comparative study between synthetic and dairy wastewaters in single chamber microbial fuel cell for power generation

2021 ◽  
Author(s):  
Payel Choudhury ◽  
Ria Majumdar ◽  
Tarun Kanti Bandyopadhyaya
Keyword(s):  
Fuel Cell ◽  
Microbial Fuel Cell ◽  
Oxygen Demand ◽  
Dairy Wastewater ◽  
Synthetic Wastewater ◽  
Inoculum Concentration ◽  
Single Chamber ◽  
Renewable Power ◽  
Ph Process ◽  
High Chemical Oxygen Demand

To investigate the performance of microbial fuel cell (MFC) with a single-chamber membrane, Pseudomonas aeruginosa is used as a bio catalyst for various synthetic wastewaters rich in carbohydrate and is compared with real dairy wastewater in this experiment. Therefore, the choice of appropriate carbon, nitrogen, NaCl, inoculum content, temperature, and pH process parameters are used for preparing synthetic wastewater was agreed upon by one-variable-at-a time approach. Maximum levels of voltage generation attained from the synthetic wastewater was 485 mV when supple­mented with 1.5 % of lactose as a source of carbon, 0.3 % of ammonium chloride as a decent nitrogen source, 0.03 % of NaCl, inoculum concentration of 3 %, the temperature at 37 oC and pH 7. On the other hand, the maximum voltage attained with real dairy wastewater was 561 mV with high chemical oxygen demand (COD) value of 801 mg l-1. The maximum power density obtained from dairy wastewater was 73.54 mW m-2. Thus, High voltage achieved for MFC operating with real dairy wastewater suggests that it can be used not only for the industrial application to generate more renewable power, but also for the wastewater treatment carried out at the same time.

Electricity Production from Dual Chambers Microbial Fuel Cell Fed with Chicken Manure-Wastewater

2015 ◽  
Vol 3 (1) ◽  
pp. 9-18
Author(s):  
Ali J. Jaeel
Keyword(s):  
Fuel Cell ◽  
Microbial Fuel Cell ◽  
Chicken Manure ◽  
Electricity Production ◽  
Anaerobic Sludge ◽  
Livestock Wastewater ◽  
Graphite Electrodes ◽  
Reliable Source ◽  
Current Densities ◽  
Resistance Value

Chicken manure wastewaters are increasingly being considered a valuable resource of organic compounds. Screened chicken manure was evaluated as a representative solid organic waste. In this study, electricity generation from livestock wastewater (chicken manure) was investigated in a continuous mediator-less horizontal flow microbial fuel cell with graphite electrodes and a selective type of membrane separating the anodic and cathodic compartments of MFC from each other. The performance of MFC was evaluated to livestock wastewater using aged anaerobic sludge. Results revealed that COD and BOD removal efficiencies were up to 88% and 82%, respectively. At an external resistance value of 150 Ω, a maximum power and current densities of 278 m.W/m2 and 683 mA/m2, respectively were obtained, hence MFC utilizing livestock wastewater would be a sustainable and reliable source of bio-energy generation .

A Study on Polythiophene Modified Carbon Cloth as Anode in Microbial Fuel Cell for Lead Removal

2021 ◽  
Author(s):  
Rajkumar Rajendran ◽  
Gnana Prakash Dhakshina Moorthy ◽  
Haribabu Krishnan ◽  
Sumisha Anappara
Keyword(s):  
Fuel Cell ◽  
Microbial Fuel Cell ◽  
Lead Removal ◽  
Carbon Cloth
Sign in / Sign up

Export Citation Format

Share Document