scholarly journals Effect of Al2O3 Particles and Precipitation Hardening on the Properties of Cast 332 Aluminum Alloy

2018 ◽  
Vol 14 (4) ◽  
pp. 125-132
Author(s):  
Akeel Dhahir Subhi ◽  
Hussein Najim Abdullah
Keyword(s):  
Heat Treatment ◽  
Solution Heat Treatment ◽  
Precipitation Hardening ◽  
Hardness Test ◽  
Al Alloy ◽  
Heat Treated ◽  
The Matrix ◽  
Al2o3 Particles ◽  
Pin On Disk ◽  
Refinement Effect

In this work, 332 Al alloy was prepared and reinforced with (0.5% and 1%) nano-Al2O3 particles. The prepared unreinforced and reinforced 332 Al alloy with nano-Al2O3 were solution heat treated (T6) at 510 ̊C and aged at 225 ̊C with different times (1, 3, and 5 h). Hardness test was performed on all the prepared alloys. All prepared alloys were dry slided under different applied loads (5, 10, 15, and 20 N) against steel counterface surface using pin on disk apparatus. The results showed that refinement effect was observed after addition of nano-Al2O3 particles and a change in silicon morphology after performing the solution heat treatment. The results also showed that hardness was increased and the wear rate was decreased with increasing the nano-Al2O3 particles in the matrix of 332 Al-Alloy

Solution Heat Treatment of 7075 Aluminum Alloy Affected on Anodic Oxide Layer

2016 ◽  
Vol 867 ◽  
pp. 19-23 ◽  
Author(s):  
Itsaree Iewkitthayakorn ◽  
Somjai Janudom ◽  
Narissara Mahathaninwong
Keyword(s):  
Heat Treatment ◽  
Oxide Film ◽  
Solution Heat Treatment ◽  
Treatment Time ◽  
Solution Treatment ◽  
Secondary Phase ◽  
Anodic Oxide ◽  
Al Alloy ◽  
Heat Treated

This research focused on the effect of solution heat treated microstructures on anodic oxide formations of casting 7075 Al alloy. The casting specimens were solution heat treated at 450°C for various holding. The results showed that the quality of anodic oxide film on the specimen with 4h solution heat treatment time was higher than that of at other conditions. Because its microstructures obtained the lowest amounts of secondary phase particles leading to improve the quality of oxide film and also reduce defects in oxide film. On the other hand, coarse black particles of Mg2Si formed increasingly in microstructures of specimens after solution treatment at prolong holding time of 8h and 16h resulted in discontinues oxide films forming on them.

scholarly journals The Effect of Aging on Precipitates, Mechanical and Magnetic Properties of Fe-21Cr-15Ni-6Mn-Nb Low Magnetic Stainless Steel

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 819
Author(s):  
Changsheng Li ◽  
Kun Li ◽  
Jingbo Dong ◽  
Jinyi Ren ◽  
Yanlei Song
Keyword(s):  
Heat Treatment ◽  
Tensile Strength ◽  
Stainless Steel ◽  
Magnetic Properties ◽  
Solution Heat Treatment ◽  
Aging Treatment ◽  
Relative Magnetic Permeability ◽  
Coarsening Behavior ◽  
The Matrix ◽  
Coherent Orientation

The effect of aging on the precipitates, mechanical and magnetic properties of Fe-21Cr-15Ni-6Mn-Nb low magnetic stainless steel were investigated. The steel was aged at 550–750 °C for 2 h after solution heat treatment at 1100 °C for 1 h. During the aging treatment, the (Nb, V)(C, N) particles gradually precipitated in the grain, which were coherent or semi-coherent with the matrix. When the aging temperature was beyond 650 °C, the coarsening rate of (Nb, V)(C, N) particles increase rapidly and the coherent orientation between (Nb, V)(C, N) particles and the matrix was lost gradually. Meanwhile, coarse M23C6 was distributed at the grain boundary with chain shape, which was non-coherent with the matrix. The coarsening behavior of (Nb, V)(C, N) precipitates in the grain was analyzed, and the size of the particles precipitated after aging treatment at 650°C for different time was calculated and studied. After aging treatment at 650 °C for 2 h, the yield strength and tensile strength of the stainless steel was 705.6 MPa and 1002.3 MPa, the elongation and the relative magnetic permeability was 37.8% and 1.0035, respectively.

The effect of ageing duration on the mechanical properties of Al alloy 6061-garnet composites

2001 ◽  
Vol 215 (2) ◽  
pp. 113-119
Author(s):  
S C Sharma
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Al Alloy ◽  
Destructive Testing ◽  
Transmission Electron ◽  
Heat Treated ◽  
The Matrix ◽  
Reinforcing Particle ◽  
Alloy 6061

A well-consolidated composite of Al alloy 6061 reinforced with 4, 8 and 12 wt% garnet was prepared by a liquid metallurgy technique, the composite was heat treated for different ageing durations (T6 treatment), and its mechanical properties were determined by destructive testing. The results of the study indicated that, as the garnet particle content in the composites increased, there were marked increases in the ultimate tensile strength, compressive strength and hardness but there was a decrease in the ductility. There was an improvement in the tensile strength, compressive strength, and hardness with ageing due to precipitation. Precipitation in Al alloy 6061, with and without garnet particulate reinforcement, was studied using transmission electron microscopy. The fracture behaviour of the composites was altered significantly by the presence of garnet particles and the crack propagation through the matrix, and the reinforcing particle clusters resulted in final fracture.

Heat Treatment and Wear Characteristics of Al2O3 and TiC Particulate Reinforced AA6063 Al Alloy Hybrid Composites

2006 ◽  
Vol 128 (4) ◽  
pp. 891-894 ◽  
Author(s):  
M. Abdel Aziz ◽  
T. S. Mahmoud ◽  
Z. I. Zaki ◽  
A. M. Gaafer
Keyword(s):  
Heat Treatment ◽  
Sliding Wear ◽  
Hybrid Composites ◽  
Wear Behavior ◽  
Age Hardening ◽  
Peak Hardness ◽  
Dry Sliding Wear ◽  
Al Alloy ◽  
Composite Alloy ◽  
Al2o3 Particles

In this article, the heat treatment and dry sliding wear behavior of Al-based AA6063 alloy reinforced with both TiC and Al2O3 ceramic particles were studied. The particles were synthesized by self-propagating high temperature synthesis (SHS) technique. The prepared composite alloy contains 5vol.%Al2O3 and 5vol.% TiC particles. The composite alloy was prepared by vortex method. To attain the peak hardness values of the alloys, age hardening behavior of the monolithic alloy and also the composite alloy was investigated. The wear tests were performed at room temperature using a pin-on-disk type apparatus. The results showed that the addition of TiC and Al2O3 particles increases the hardness of the AA6063 Al alloy and at the same time accelerates the aging kinetics. The sliding wear properties of AA6063 Al alloy were significantly improved by the addition of TiC and Al2O3 particles.

Microstructure and cavitation in the superplastic Zn-22 wt% Al alloy: Effect of solution heat treatment

1994 ◽  
Vol 70 (1) ◽  
pp. 7-13 ◽  
Author(s):  
Kyung-Tae Park ◽  
James C. Earthman ◽  
Farghalli A. Mohamed
Keyword(s):  
Heat Treatment ◽  
Solution Heat Treatment ◽  
Al Alloy ◽  
Alloy Effect

Comparison of Microstructure and Mechanical Properties of Additively Manufactured and Conventional Maraging Steel

2020 ◽  
Vol 405 ◽  
pp. 133-138
Author(s):  
Ludmila Kučerová ◽  
Andrea Jandová ◽  
Ivana Zetková
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Maraging Steel ◽  
Precipitation Hardening ◽  
High Strength ◽  
Hardness Measurement ◽  
Nickel Steel ◽  
Heat Treated ◽  
Good Material ◽  
Iron Nickel

Maraging steel is an iron-nickel steel alloy, which achieves very good material properties like high toughness, hardness, good weldability, high strength and dimensional stability during heat treatment. In this work, maraging steel 18Ni-300 was manufactured by selective laser melting. It is a method of additive manufacturing (AM) technology, which produces prototypes and functional parts. Sample of additively manufactured and conventional steel with the same chemical composition were tested after in three different states – heat treated (as-built/as-received), solution annealed and precipitation hardened. Resulting microstructures were analysed by light and scanning electron microscopy and mechanical properties were obtained by hardness measurement and tensile test. Cellular martensitic microstructures were observed in additively manufactured samples and conventional maraging steel consisted of lath martensitic microstructures. Very similar mechanical properties were obtained for both steels after the application of the same heat treatment. Ultimate tensile strengths reached 839 – 900 MPa for samples without heat treatment and heat treated by solution annealing, the samples after precipitation hardening had tensile strengths of 1577 – 1711 MPa.

Corrosion behavior of heat-treated and cryorolled Al 5052 alloys in different chloride ion concentrations

2020 ◽  
Vol 67 (1) ◽  
pp. 7-15 ◽  
Author(s):  
Anasyida Abu Seman ◽  
Ji Kit Chan ◽  
Muhammad Anas Norazman ◽  
Zuhailawati Hussain ◽  
Dhindaw Brij ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Corrosion Behaviour ◽  
Solution Treatment ◽  
Chloride Ion ◽  
Optical Microscope ◽  
Al Alloy ◽  
Content Type ◽  
Ion Concentrations ◽  
Heat Treated ◽  
Chloride Environment

Purpose This paper aims to investigate the corrosion behaviour of heat-treated and cryorolled Al 5052 alloys in different Cl− ion concentrations. Design/methodology/approach NaCl solutions with concentrations of 0, 0.5, 3.5 and 5.5 per cent were selected. Samples were subjected to pre-heat treatment (annealing at 300 °C and solution treatment at 540 °C) and cryorolling up to 30 per cent reduction before undergoing corrosion tests. The corrosion behaviour of the samples was then investigated by potentiodynamic polarization. The microstructure of the corroded samples was evaluated under an optical microscope, and the percentages of pits on their surfaces were calculated. Findings The cryorolled samples had a lower corrosion rate than the samples that were not cryorolled. The cryorolled sample that underwent solution treatment showed the highest corrosion resistance among all the samples tested. Practical implications The commercial impact of the study is the possibility of using the cryorolled Al alloy in various ion chloride environment. Originality/value The obtained results help in understanding the corrosion behaviour of cryorolled samples under different heat treatment conditions.

Effect of Ageing on Microstructures, Electrical Properties and PALS of Aircraft Al Alloy 2024

2011 ◽  
Vol 319-320 ◽  
pp. 51-59 ◽  
Author(s):  
Abdullah A. Refeay ◽  
N.A. Kamel ◽  
M.A. Abdel-Rahman ◽  
Yahia A. Lotfy ◽  
Emad A. Badawi
Keyword(s):  
Heat Treatment ◽  
Aluminum Alloy ◽  
Electrical Properties ◽  
Hardness Test ◽  
Al Alloy ◽  
Property Development ◽  
2024 Aluminum Alloy ◽  
Different Temperatures ◽  
Lcr Meter ◽  
Vickers Hardness Test

A comprehensive and systematic study using PALS technique, Vickers hardness test and electrical LCR meter were undertaken to follow property development during the recently promoted interrupted ageing treatment for 2024 aluminum alloy. In this work, solution heat treatments at different temperatures were performed in aircraft materials 2024 aluminum alloy. This work describes the development of the dependence of mechanical, electrical properties of 2024 Al-alloys on heat treatment to characterize microstructural changes during heat treatment. PALS, mechanical and electrical testing will be used to measure the features of the material as a function of time for each ageing temperatures.

Sign in / Sign up

Export Citation Format

Share Document