scholarly journals Influence of Volume Percentage and Fibers Alignments of Banana Fiber on Impact Strength of Epoxy Banana Composite

2021 ◽  
Vol 9 (12) ◽  
pp. 1539-1543
Author(s):  
Khan Asem Ali
Keyword(s):  
Impact Strength ◽  
Epoxy Resin ◽  
Fiber Orientation ◽  
Epoxy Matrix ◽  
Fiber Reinforcement ◽  
Synthetic Fiber ◽  
Banana Fiber ◽  
Volume Percentage ◽  
Banana Fibers ◽  
The Impact

Abstract: The world that is evolving at a very fast pace, the anxiety of the environment pollutions increasing has tip the necessity for new eco-friendly materials, researchers have started to develop sustainable materials that are renewable as well as biodegradable in nature. The natural fibers have certain advantages above synthetic fiber materials, they are lower in cost and density with comparable strength. In the present study, banana fiber is reinforced in the epoxy matrix and a composite material is prepared and impact strength of these composites are estimated. This composite samples are prepared by Wet lay-up method with varying banana fibers volume percentages by (10%, 20%, 30%, 40%) and by changing the fibers orientation in the epoxy matrix by (00 ,900 , woven Bi-directional). The results shows that there is gradual increase in the impact strength of the epoxy for 900 banana fiber orientation, the optimum results were found for 40% banana fiber and 60% epoxy resin, as for woven BD there was an increase in the impact strength up to 20% banana fiber reinforcement, as for 00 orientation the strength increases up to 10% fiber reinforcement above this there was a drastic reduction in the impact strength. Keywords: Banana Fiber, Epoxy Resin, Volume percent, Fiber Orientation, Impact Strength

scholarly journals A brief review on mechanical and thermal properties of banana fiber based hybrid composites

2021 ◽  
Vol 3 (2) ◽  
Author(s):  
P. Sivaranjana ◽  
V. Arumugaprabu
Keyword(s):  
Thermal Properties ◽  
Natural Fiber ◽  
Hybrid Composites ◽  
Fiber Reinforcement ◽  
Mechanical And Thermal Properties ◽  
Banana Fruit ◽  
Banana Plant ◽  
Banana Fiber ◽  
Banana Fibers ◽  
The Impact

AbstractThe usage of banana natural fibers along with polymer matrix composites had created much interest among the researchers due to their low cost, easy availability, strength and enhancement in properties such as mechanical, wear, electrical and thermal. Banana plant is cultivated all over the world which is familiarly used as food products especially banana fruit as well as many household items made from banana fibers. The natural fiber extracted from the banana stem proves to be a potential reinforcement in the composite manufacturing. This review is very much needed because of the enormous research reported on the banana fiber reinforced polymer composites, with such an excellent property offered by this banana fiber reinforcement the impact of hybridization and its need also to be addressed. This brief review article gives a detail information about the combinations of various hybrid composites produced using the banana fiber along with various other natural/synthetic fibers in the polymer matrixes and its performance improvement especially in the mechanical and thermal properties. From the review it was inferred that 30–50% increase in all the mechanical properties such as Tensile, Flexural and Impact strength. Also in addition an enhancement in thermal and moisture resistance also noted. In addition during this review the research gap observed is that the development of bio composites based on banana fiber is very limited and also the influence of banana fiber along with bio resin needs to be studied. The properties such as fatigue, fire resistance also to be analyzed using the banana fiber reinforcement.

scholarly journals The Effects of Sodium Hydroxide and Soda AQ Content on Mechanical and Physical Properties of Waste Flax Fibre Pulp Reinforced Polymer Composite Sheet

2020 ◽  
Vol 9 (2) ◽  
pp. 8-15
Author(s):  
Anupam Kumar ◽  
Ramratan . ◽  
Rohit Kumar
Keyword(s):  
Tensile Strength ◽  
Impact Strength ◽  
Epoxy Resin ◽  
Natural Fiber ◽  
Testing Machine ◽  
Flax Fiber ◽  
Alkaline Solutions ◽  
Volume Percentage ◽  
Flax Fibres ◽  
The Impact

The aim of this study is utilized agricultural waste which may be profitable, pollution free and economically viable for the farmer and industries. In this experiment short flax fiber pulp is the natural fiber component chemically treated with alkaline solutions. Six specimens will be prepared in different volume percentage of flax fiber pulp and epoxy resin in order to get more accurate results. In this study it has been aimed to use flax fibres in composite materials and to study the mechanical properties of the produced samples. The mechanical tests results (thickness test, Tensile strength and impact strength tests) and SEM micrographs indicated flax fibres as an alternative natural fibre source for developing reinforced composites for various industries. The content of short flax fiber pulp is varied (35%, 45%, 55%) weight percentage whereas the epoxy resin is varied (50%, 40%, 30%) percentage is kept constant 15% in hardener. All the sample have been tested in universal testing machine as per ASTM standard for tensile strength and impact strength it is observed that composite with 35% flax fiber pulp is having highest tensile strength of 4 mm (4.57 Mpa) and 8 mm (6.04 Mpa). The impact strength of composite with 35% flax fiber pulp was highest than 45% to 55% flax fiber pulp.

scholarly journals Impact Strength of Hybrid Epoxy–Basalt Composites Modified with Mineral and Natural Fillers

2021 ◽  
Vol 5 (3) ◽  
pp. 56
Author(s):  
Danuta Matykiewicz ◽  
Mateusz Barczewski ◽  
Marwan Suleiman Mousa ◽  
Mavinkere Rangappa Sanjay ◽  
Suchart Siengchin
Keyword(s):  
Impact Strength ◽  
Epoxy Resin ◽  
Epoxy Matrix ◽  
Basalt Fiber ◽  
Fiber Reinforced Composites ◽  
Maximum Force ◽  
Reinforced Composites ◽  
The Impact ◽  
Natural Fillers ◽  
Natural Additives

The aim of this study was to evaluate the influence of mineral and natural additives (2.5; 5; 10 wt.%) on the impact strength of epoxy–basalt composites. Three types of filler were used to modify the epoxy matrix: basalt powder (BP), basalt microfiber (BF) and sunflower husk ash (SA). The impact strength and the maximum force were determined for the materials. The results of the conducted research confirm that the addition of a powder fillers to the epoxy matrix of basalt fiber reinforced composites is an effective method of improving their impact characteristic. The introduction of fillers to epoxy resin allowed to improve the impact properties of all tested groups of laminates. Moreover, in all cases, the introduction of the filler increased the maximum force needed to damage the composite sample and their hardness. For the modified materials, an increase in impact strength was recorded, respectively: by 44% for composites with BP, by 7.5% for composites with BF and by 2.5% for composites with SA.

Preparation and properties of novel sulfonic graphene oxide–epoxy resin nanocomposites by resin transfer molding process

2016 ◽  
Vol 51 (9) ◽  
pp. 1197-1208 ◽  
Author(s):  
Wei Li ◽  
Hongyu Li ◽  
Xinguo Yang ◽  
Wei Feng ◽  
Hongyun Huang
Keyword(s):  
Graphene Oxide ◽  
Impact Strength ◽  
Epoxy Resin ◽  
Curing Temperature ◽  
Flexural Property ◽  
Oxide Content ◽  
Molding Process ◽  
One Pot ◽  
Epoxy Resin Nanocomposites ◽  
The Impact

This paper reported a facile one-pot strategy for fabrication of sulfonic graphene oxide–epoxy resin nanocomposites. The rheological and thermal properties were employed to characterize the viscosity and the curing temperature of epoxy resin. Fourier transform infrared spectra for sulfonic graphene oxide and nanocomposites indicated that the sulfonic graphene oxide contains chemical cross-linking responsible for better interactions with the epoxy resin. The state of dispersion was evaluated at different scales by still picture camera and scanning electron microscopy (SEM). Tensile property tests indicated that the tensile strength and elasticity modulus of sulfonic graphene oxide–epoxy resin nanocomposites decreased slowly with increasing of sulfonic graphene oxide content. The critical flexural property and impact strength of epoxy resin filled with sulfonic graphene oxide nanocomposites were measured. The content, size, and dispersion state of sulfonic graphene oxide were examined. It was found that the content of sulfonic graphene oxide has greater impact on both flexural property and impact strength of nanocomposites compared with other conditions. For instance, the impact strength increased by 113.0% and the flexural strength and modulus increased by 39.3% and 55.7% using 1 wt.% sulfonic graphene oxide as compared to neat epoxy resin.

Preparation and Mechanical Properties of Epoxy Resin Reinforced with Jeffamines-Grafted Carbon Nanotubes

2009 ◽  
Vol 79-82 ◽  
pp. 553-556 ◽  
Author(s):  
Ling Fei Shi ◽  
Gang Li ◽  
Gang Sui ◽  
Xiao Ping Yang
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Epoxy Resin ◽  
Photoelectron Spectroscopy ◽  
Epoxy Matrix ◽  
Resin Matrix ◽  
Mechanical And Thermal Properties ◽  
Time Dynamic ◽  
Multi Walled Carbon Nanotubes ◽  
The Impact

The increasing proliferation and application of advanced polymer composites requires higher and broader performance resin matrices. Poly(oxypropylene) with –NH2 end-groups has been widely used to toughen epoxy resins, but the strength of resin matrix may be reduced due to the addition of flexible segments in the crosslinking network. Carbon nanotubes (CNTs) have been paid more and more attention in recent years because of their superior thermal and mechanical properties. In this paper, CNTs grafted with Jeffamines T403 were used to simultaneously improve the reinforcement and toughening of an epoxy resin. The untreated multi-walled carbon nanotubes (u-MWNTs) were functionalized with amine groups according to three steps: carboxylation, acylation, and amidation. The f-MWNTs were characterized by Fourier transform infra-red (FTIR) and X-ray photoelectron spectroscopy (XPS). The experimental results indicated that the T403 was grafted to the surface of MWCNTs. The mechanical and thermal properties of epoxy with f-MWNTs were investigated. The tensile and flexural strength increased by 7.77 % and 7.03 % after adding 0.5wt% f-MWCNTs without sacrificing the impact toughness. At the same time, dynamic mechanical thermal analysis (DMTA) showed that the glass transition temperature (Tg) of epoxy with f-MWNTs were increased. The fracture surface of epoxy with f-MWNTs was observed by scanning electron microscopy (SEM) to understand the dispersion of f-MWNTs in epoxy matrix and interfacial adhesion between f-MWNTs and epoxy matrix, which can be attributed to the strong interfacial bonding between f-MWNTs and epoxy resin.

scholarly journals PPG-Terminated Tetra-Carbamates as the Toughening Additive for Bis-A Epoxy Resin

Polymers ◽  
2019 ◽  
Vol 11 (9) ◽  
pp. 1522
Author(s):  
Ming Zhang ◽  
Mingqing Chen ◽  
Zhongbin Ni
Keyword(s):  
Epoxy Resin ◽  
Epoxy Matrix ◽  
Microphase Separation ◽  
Intramolecular Interactions ◽  
Hexamethylene Diisocyanate ◽  
Separation Mechanism ◽  
Toughening Mechanism ◽  
The Impact ◽  
Modified Epoxy ◽  
Epoxy Systems

We synthesized PPG-terminated tetra-carbamates as a new toughening additive for epoxy thermosets through facile addition reaction of hexamethylene diisocyanate (HDI) with poly(tetra-methylene glycols) (PTMG) and poly(propylene glycols) (PPG). The effects of prepared tetra-carbamates on the rheological behavior of neat epoxy resin were studied along with the various cured properties of their modified epoxy systems. Four carbamate groups (–NHCOO–) endow the prepared additives not only with good intramolecular interactions, but also with optimal intermolecular interactions with epoxy polymers. This results in the suitable miscibility of the additives with the epoxy matrix for the formation of the typical biphasic structure of microparticles dispersed in the epoxy matrix via polymerization-induced microphase separation. The impact strength and critical stress concentration factor (KIC) of cured modified epoxy systems with the additives are significantly higher than those of unmodified epoxy systems, without sacrificing the processability (Tg) and flexural strength. The toughening mechanism is understood as a synergism combination among the phase separation mechanism, the in situ homogeneous toughening mechanism, and the particle cavitation mechanism.

scholarly journals Preparation and properties of flame-retardant epoxy resins containing reactive phosphorus flame retardant

2020 ◽  
Vol 15 ◽  
pp. 155892502090132
Author(s):  
Sang-Hoon Lee ◽  
Seung-Won Oh ◽  
Young-Hee Lee ◽  
Il-Jin Kim ◽  
Dong-Jin Lee ◽  
...  
Keyword(s):  
Impact Strength ◽  
Flame Retardant ◽  
Epoxy Resin ◽  
Flame Retardancy ◽  
Epoxy Resins ◽  
Phosphorus Content ◽  
Phosphorus Compound ◽  
Phosphorus Compounds ◽  
Limiting Oxygen Index ◽  
The Impact

To prepare flame-retardant epoxy resin, phosphorus compound containing di-hydroxyl group (10-(2,5-dihydroxyphenyl)-9,10-dihydro-9-oxa-10-phospha phenanthrene-10-oxide, DOPO-HQ) was reacted with uncured epoxy resin (diglycidyl ether of bisphenol A, YD-128) and then cured using a curing agent (dicyandiamide, DICY). This study focused on the effect of phosphorus compound/phosphorus content on physical properties and flame retardancy of cured epoxy resin. The thermal decomposition temperature of the cured epoxy resins (samples: P0, P1.5, P2.0, and P2.5, the number represents the wt% of phosphorus) increased with increasing the content of phosphorus compound/phosphorus (0/0, 19.8/1.5, 27.8/2.0, and 36.8/2.5 wt%) based on epoxy resin. The impact strength of the cured epoxy resin increased significantly with increasing phosphorus compound content. As the phosphorus compound/phosphorus content increased from 0/0 to 36.8/2.5 wt%, the glass transition temperature (the peak temperature of loss modulus curve) increased from 135.2°C to 142.0°C. In addition, as the content of phosphorous compound increased, the storage modulus remained almost constant up to higher temperature. The limiting oxygen index value of cured epoxy resin increased from 21.1% to 30.0% with increasing phosphorus compound/phosphorus content from 0/0 to 36.8/2.5 wt%. The UL 94 V test result showed that no rating for phosphorus compounds less than 19.8 wt% and V-1 for 27.8 wt%. However, when the phosphorus compound was 36.8 wt%, the V-0 level indicating complete flame retardancy was obtained. In conclusion, the incorporation of phosphorus compounds into the epoxy chain resulted in improved properties such as impact strength and heat resistance, as well as a significant increase in flame retardancy.

scholarly journals Impact Damage Resistance and Post-Impact Tolerance of Optimum Banana-Pseudo-Stem-Fiber-Reinforced Epoxy Sandwich Structures

2020 ◽  
Vol 10 (2) ◽  
pp. 684 ◽  
Author(s):  
Mohamad Zaki Hassan ◽  
S. M. Sapuan ◽  
Zainudin A. Rasid ◽  
Ariff Farhan Mohd Nor ◽  
Rozzeta Dolah ◽  
...  
Keyword(s):  
Composite Structures ◽  
Sandwich Structures ◽  
Impact Damage ◽  
Fiber Composite ◽  
Peak Load ◽  
Weight Ratio ◽  
Synthetic Fiber ◽  
Damage Area ◽  
Banana Fibers ◽  
The Impact

Banana fiber has a high potential for use in fiber composite structures due to its promise as a polymer reinforcement. However, it has poor bonding characteristics with the matrixes due to hydrophobic–hydrophilic incompatibility, inconsistency in blending weight ratio, and fiber length instability. In this study, the optimal conditions for a banana/epoxy composite as determined previously were used to fabricate a sandwich structure where carbon/Kevlar twill plies acted as the skins. The structure was evaluated based on two experimental tests: low-velocity impact and compression after impact (CAI) tests. Here, the synthetic fiber including Kevlar, carbon, and glass sandwich structures were also tested for comparison purposes. In general, the results showed a low peak load and larger damage area in the optimal banana/epoxy structures. The impact damage area, as characterized by the dye penetration, increased with increasing impact energy. The optimal banana composite and synthetic fiber systems were proven to offer a similar residual strength and normalized strength when higher impact energies were applied. Delamination and fracture behavior were dominant in the optimal banana structures subjected to CAI testing. Finally, optimization of the compounding parameters of the optimal banana fibers improved the impact and CAI properties of the structure, making them comparable to those of synthetic sandwich composites.

Research of Epoxy Resin Modified by Polyether Imidazole Ionic Liquid

2014 ◽  
Vol 926-930 ◽  
pp. 198-201
Author(s):  
Li Ying Guo ◽  
Jin Lin Liu ◽  
Peng Cheng Huang ◽  
Jun Hai He ◽  
Shi Yang Bai ◽  
...  
Keyword(s):  
Ionic Liquid ◽  
Impact Strength ◽  
Epoxy Resin ◽  
General Purpose ◽  
Rubber Elasticity ◽  
Curing Agent ◽  
The Impact

Polyether imidazole ionic liquid (PIIL) was blended with general-purpose epoxy resin (EP). PIIL/EP was cured by ethylenediamine curing agent. The structure of PIIL/EP was determined by FTIR. The effect of the content of PIIL on the impact strength of EP was studied. The toughness of epoxy resin could be significantly improved by PIIL. The impact strength of the modified EP was improved with the increase of PIIL and leveled off when the content of PIIL was more than 45%, and the modified EP showed rubber elasticity obviously.

Lower Branched Liquid Crystalline Polyester POSS Used as Collaborative Modifier for Epoxy Resin

2010 ◽  
Vol 150-151 ◽  
pp. 698-702
Author(s):  
Zhi You Yang ◽  
Shao Rong Lu ◽  
Zhi Yi Huang ◽  
Chun He Yu ◽  
Kuo Liu
Keyword(s):  
Impact Strength ◽  
Epoxy Resin ◽  
Decomposition Rate ◽  
Liquid Crystalline ◽  
Hydroxybenzoic Acid ◽  
Trimellitic Anhydride ◽  
Maximum Decomposition Rate ◽  
Oligomeric Silsesquioxane ◽  
The Impact ◽  
Liquid Crystalline Polyester

A new kind of lower-branched liquid crystalline polyester (LLCP) containing polyester mesogenic units was synthesized by p-hydroxybenzoic acid, terephthalyl chloride and trimellitic anhydride (TMA), then was used as collaborative modifier for the epoxy resin (E-51) with γ-azyl polyhedral oligomeric silsesquioxane (POSS). The experimental results showed that the LLCP / POSS could act as an effective toughening modifier for the epoxy resin. The impact strength of the composites modified with LLCP and POSS was 1.1 times higher than that of the unmodified system. The temperature of starting decomposition and maximum decomposition rate improved about 20 oC and 13 oC , respectively.

Sign in / Sign up

Export Citation Format

Share Document