scholarly journals Structure and characteristics of the hot pressed hydroxyapatite/poly-L-lactide composite

2002 ◽  
Vol 34 (1) ◽  
pp. 79-93 ◽  
Author(s):  
Nenad Ignjatovic ◽  
Edin Suljovrujic ◽  
Z. Stojanovic ◽  
Dragan Uskokovic
Keyword(s):  
Hot Pressing ◽  
Three Dimensional ◽  
Dispersion Analysis ◽  
Degree Of Crystallinity ◽  
Time Interval ◽  
Scanning Calorimetry ◽  
Pressing Time ◽  
Ir Study ◽  
Electron Dispersion ◽  
The Degree Of Crystallinity

Hydroxyapatite/poly-L-lactide (HAp/PLL) composite biomaterial can be obtained by different processing methods. Three-dimensional blocks of HAp/PLLA composite biomaterial with mechanical characteristics close to the natural bone tissue can be obtained by hot pressing procedure. Effects of synthesis and compacting on the structure and characteristics of the HAp/PLLA composite biomaterial were studied in this work. Using wade angle X-ray structural analyses (WAXS), differentially scanning calorimetry (DSC), thermogravimetric analysis (TGA) and infrared (IR) spectroscopy, the changes occurring in the material during synthesis and hot pressing were monitored. Surface microstructure was analyzed by scanning electronic microscopy (SEM) coupled with electron-dispersion analysis (EDX). The results obtained indicate a possible decrease in the degree of crystallinity with hot pressing time increase. A block of HAp/PLLA composite biomaterial with 1.6 times lower crystallinity of the polymer phase was obtained by hot pressing in a given time interval with a maximum of 60 minutes. Results of TG analysis show that PLLA stability decreases with increasing hot pressing time, and vice versa. IR study proved that neither destructive changes in constituents nor formation of new phases occurred during hot pressing.

scholarly journals Preparation and Characterization of Talc Filled Thermoplastic Polyurethane/Polypropylene Blends

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Emi Govorčin Bajsić ◽  
Vesna Rek ◽  
Ivana Ćosić
Keyword(s):  
Thermal Properties ◽  
Thermoplastic Polyurethane ◽  
Mechanical Analysis ◽  
Degree Of Crystallinity ◽  
Scanning Calorimetry ◽  
Polypropylene Blends ◽  
Pp Blends ◽  
The Degree Of Crystallinity ◽  
Better Than

The effect of the addition of talc on the morphology and thermal properties of blends of thermoplastic polyurethane (TPU) and polypropylene (PP) was investigated. The blends of TPU and PP are incompatible because of large differences in polarities between the nonpolar crystalline PP and polar TPU and high interfacial tensions. The interaction between TPU and PP can be improved by using talc as reinforcing filler. The morphology was observed by means of scanning electron microscopy (SEM). The thermal properties of the neat polymers and unfilled and talc filled TPU/PP blends were studied by using dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The addition of talc in TPU/PP blends improved miscibility in all investigated TPU/T/PP blends. The DSC results for talc filled TPU/PP blends show that the degree of crystallinity increased, which is due to the nucleating effect induced by talc particles. The reason for the increased storage modulus of blends with the incorporation of talc is due to the improved interface between polymers and filler. According to TGA results, the addition of talc enhanced thermal stability. The homogeneity of the talc filled TPU/PP blends is better than unfilled TPU/PP blends.

scholarly journals Thermal Properties and Non-Isothermal Crystallization Kinetics of Poly (δ-Valerolactone) and Poly (δ-Valerolactone)/Titanium Dioxide Nanocomposites

Crystals ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 452 ◽  
Author(s):  
Waseem Saeed ◽  
Abdel-Basit Al-Odayni ◽  
Abdulaziz Alghamdi ◽  
Ali Alrahlah ◽  
Taieb Aouak
Keyword(s):  
Titanium Dioxide ◽  
Crystallization Kinetics ◽  
Isothermal Crystallization ◽  
Three Dimensional ◽  
Degree Of Crystallinity ◽  
Simultaneous Occurrence ◽  
Scanning Calorimetry ◽  
Isothermal Crystallization Kinetics ◽  
The Stability ◽  
Kinetics Of

New poly (δ-valerolactone)/titanium dioxide (PDVL/TiO2) nanocomposites with different TiO2 nanoparticle loadings were prepared by the solvent-casting method and characterized by Fourier transform infra-red, differential scanning calorimetry, X-ray diffraction and scanning electron microscopy, and thermogravimetry analyses. The results obtained reveal good dispersion of TiO2 nanoparticles in the polymer matrix and non-formation of new crystalline structures indicating the stability of the crystallinity of TiO2 in the composite. A significant increase in the degree of crystallinity was observed with increasing TiO2 content. The non-isothermal crystallization kinetics of the PDVL/TiO2 system indicate that the crystallization process involves the simultaneous occurrence of two- and three-dimensional spherulitic growths. The thermal degradation analysis of this nanocomposite reveals a significant improvement in the thermal stability with increasing TiO2 loading.

scholarly journals Impact of environmental agents on non-woven polylactide/natural rubber agrofiber

2021 ◽  
Vol 285 ◽  
pp. 07034
Author(s):  
Yulia Tertyshnaya ◽  
Maksim Zakharov ◽  
Alina Ivanitskikh ◽  
Anatoliy Popov
Keyword(s):  
Natural Rubber ◽  
Uv Irradiation ◽  
Thermal Characteristics ◽  
Degree Of Crystallinity ◽  
Distilled Water ◽  
Fibrous Materials ◽  
Scanning Calorimetry ◽  
Melting Temperatures ◽  
Environmental Agents ◽  
The Degree Of Crystallinity

In the work an eco-friendly non-woven fiber made of polylactide and natural rubber with a rubber content from 0 to 15 wt.% was obtained by electrospinning. The influence of distilled water and UV irradiation on the agrofibers has been investigated. The water sorption test showed that the addition of natural rubber into the polylactide matrix does not significantly affect the degree of water absorption of the fibrous materials, which is in the range of 49-50.6%. Thermal characteristics after 180 days of degradation in distilled water at 22±2 oC and UV irradiation at a wavelength of 365 nm during 100 hours were determined using the differential scanning calorimetry. Changes in the values for glass transition and melting temperatures, and the degree of crystallinity were determined.

scholarly journals The Effect of Crystallinity on the Toughness of Cast Polyamide 6 Rods with Different Diameters

Polymers ◽  
2020 ◽  
Vol 12 (2) ◽  
pp. 293
Author(s):  
Miklós Odrobina ◽  
Tamás Deák ◽  
László Székely ◽  
Tamás Mankovits ◽  
Róbert Zsolt Keresztes ◽  
...  
Keyword(s):  
Impact Strength ◽  
Impact Test ◽  
Charpy Impact ◽  
Polyamide 6 ◽  
Degree Of Crystallinity ◽  
Scanning Calorimetry ◽  
Tensile Impact ◽  
Different Diameters ◽  
The Impact ◽  
The Degree Of Crystallinity

The present paper concentrates on the toughness and the degree of crystallinity of the magnesium-catalyzed polyamide 6 rods cast in different diametres, which are commonly used for gear manufacturing. Its toughness cannot be regarded as a constant feature due to the casting technology. The mechanical properties of the semi-finished products are sensitive to the manufactured dimension, e.g., cast diameter, which are investigated by the Charpy impact test and tensile impact test. It is generally accepted that the impact strength and tensile-impact strength correlate with the degree of crystallinity beside many other material’s feature. Crystallinity is evaluated by Differential Scanning Calorimetry. The aim of this study is to determine the relationship between toughness and crystallinity of the magnesium-catalyzed cast PA6 rods with different diameters. For the research cast rods between 40 and 300 mm diameter were selected in seven-dimensional steps. Based on the results, it was found that the toughness depends strongly on the diameter size. Furthermore, it is proved that the crystallinity explains 62.3% of the variation of the Charpy’s impact strengths, while the tensile impact method was not suitable to detect the difference between the test samples.

scholarly journals Hemp Fibre Reinforced Poly(Lactic Acid) Composites

2007 ◽  
Vol 29-30 ◽  
pp. 337-340 ◽  
Author(s):  
M.A. Sawpan ◽  
K.L. Pickering ◽  
Alan Fernyhough
Keyword(s):  
Lactic Acid ◽  
Degree Of Crystallinity ◽  
Poly Lactic Acid ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Hemp Fibre ◽  
Reinforcing Material ◽  
Fibre Loading ◽  
The Degree Of Crystallinity

The potential of hemp fibre as a reinforcing material for Poly(lactic acid) (PLA) was investigated. Good interaction between hemp fibre and PLA resulted in increases of 100% for Young’s modulus and 30% for tensile strength of composites containing 30 wt% fibre. Different predictive ‘rule of mixtures’ models (e.g. Parallel, Series and Hirsch) were assessed regarding the dependence of tensile properties on fibre loading. Limited agreement with models was observed. Differential scanning calorimetry (DSC) and x-ray diffraction (XRD) studies showed that hemp fibre increased the degree of crystallinity in PLA composites.

Investigating the Effect of Nanoclay Loadings and Re-Processing on the Melting and Crystallization Behavior of PP/Clay Nanocomposites

2019 ◽  
Vol 951 ◽  
pp. 21-25
Author(s):  
Achmad Chafidz ◽  
Sholeh Ma'mun ◽  
Haryanto ◽  
Wara Dyah Pita Rengga ◽  
Prima A. Handayani ◽  
...  
Keyword(s):  
Crystallization Behavior ◽  
Crystallization Process ◽  
The Other ◽  
Degree Of Crystallinity ◽  
Clay Nanocomposites ◽  
Scanning Calorimetry ◽  
Onset Crystallization Temperature ◽  
Significant Difference ◽  
The Degree Of Crystallinity ◽  
Melting And Crystallization

In this study, PP/clay nanocomposites have been fabricated at different nanoclay loadings, i.e. 0, 5, 10, and 5 wt% for the 1stcycle and 2ndcycle (re-processing). The prepared nanocomposites were then characterized by a Differential Scanning Calorimetry (DSC) to investigate the effects of nanoclay loadings and re-processing on the melting and crystallization of the nanocomposites. The DSC results showed that the melting temperature,Tmwas not significantly affected by the nanoclay loadings and re-processing. In the other hand, the degree of crystallinity,Xcof the nanocomposites was higher than that of neat PP, but only reached a maximum at nanoclay loading of 5 wt% (i.e. 51.2% for NC-5-I and 48.3% for NC-5-II). Thereafter, theXcdecreased at higher nanoclay loadings. There was no significant difference inXcbetween 1stcycle and 2ndcycle. Additionally, in all nanocomposites samples for both cycles, there were two crystallization temperatures, i.e.Tc1andTc2. In the overall crystallization process, theTcof nanocomposites increased by 11-12°C compared to that of neat PP. Whereas, the onset crystallization temperature,Tocalso increased by approx. 13°C. Apparently, there was no significant effect of nanoclay loadings and re-processing on theTcndTocof the nanocomposites.

Study of the structure and thermal characteristics of nanocomposites based on polyvinyl alcohol and intercalated montmorillonite

2019 ◽  
pp. 089270571987919
Author(s):  
Volodymyr Krasinskyi ◽  
Ivan Gajdos ◽  
Oleh Suberlyak ◽  
Viktoria Antoniuk ◽  
Tomasz Jachowicz
Keyword(s):  
Thermal Stability ◽  
Differential Scanning Calorimetry ◽  
Acrylic Acid ◽  
Polyvinyl Alcohol ◽  
Thermal Characteristics ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
The Degree Of Crystallinity

The structure and thermal characteristics of nanocomposites based on polyvinyl alcohol (PVA) and montmorillonite (MMT) intercalated with polyvinylpyrrolidone were investigated by X-ray diffraction analysis and differential scanning calorimetry. The modification of PVA with intercalated MMT reduces the degree of crystallinity of the resulting nanocomposites but significantly increases their thermal stability. Under ultrasound, the intercalated MMT was completely distributed in a PVA solution and formed a monocrystalline structure. Films based on PVA with modified MMT were cross-linked at 110°C in the presence of 5 wt% acrylic acid and 0.5 wt% Ferrous(II) sulfate as an initiator. The formed films have a homogeneous cross-linked structure.

scholarly journals Development and Characterization of Novel Polyurethane Films Impregnated with Tolfenamic Acid for Therapeutic Applications

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
Hilal Istanbullu ◽  
Sofia Ahmed ◽  
Muhammad Ali Sheraz ◽  
Ihtesham ur Rehman
Keyword(s):  
Polymer Concentration ◽  
Tolfenamic Acid ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Release Studies ◽  
Evaporation Technique ◽  
Crystallinity Changes ◽  
The Degree Of Crystallinity

The present study deals with the preparation of polyurethane (PU) films impregnated with a nonsteroidal anti-inflammatory drug, tolfenamic acid (TA). Solvent evaporation technique has been employed for the preparation of TA-PU films in two different ratios of 1 : 2 and 1 : 5 in Tetrahydrofuran (THF) or THF-ethanol mixtures. The prepared films were characterized using X-Ray Diffraction (XRD), Differential Scanning Calorimetry (DSC), Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), and release studies. The results indicate transformation of crystalline TA to its amorphous form. The degree of crystallinity changes both by increasing the polymer concentration and solvent used for the film preparations. The release profiles of TA were also found to be affected, showing a decrease from approximately 50% to 25% from 1 : 2 to 1 : 5 ratios, respectively.

Physicochemical Properties of Porous Starches from Different Botanical Origin

2010 ◽  
Vol 159 ◽  
pp. 363-370
Author(s):  
Hua Xi Xiao ◽  
Qin Lu Lin ◽  
Yue Wu ◽  
Wei Tian ◽  
Wei Wu
Keyword(s):  
Potato Starch ◽  
Enzyme Hydrolysis ◽  
Degree Of Crystallinity ◽  
Rice Starch ◽  
Adsorptive Capacity ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Potato Starches ◽  
The Degree Of Crystallinity

Rice, maize and potato starches were hydrolyzed by amylase to obtain porous starches as final product. The adsorptive capacity, desorbed rates, degree of crystallinity and retrogradation properties of native and porous starches were investigated. The results showed that porous starches had the stronger adsorptive capacity and slower desorbed rate compared with native starches. In the three starch materials, the adsorptive capacity of rice starch for liquids was the strongest; the adsorptive capacity of potato starch for liquids was the weakest. the more flavors adsorbed, the more flavors desorbed. X-ray diffraction showed that Enzyme hydrolysis did not result in any significant changes in the degree of crystallinity of starch. The porous starches exhibited lower tendency of retrogradation as assessed by differential scanning calorimetry (DSC).

CONNECTION BETWEEN STRUCTURAL CHANGES OF IRRIADIATED POLYETHER ETHER KETONE AND MECHANICAL PROPERTIES

Tribologia ◽  
2018 ◽  
Vol 278 (2) ◽  
pp. 95-101
Author(s):  
Aneta NIEMIEC
Keyword(s):  
Mechanical Properties ◽  
Glass Transition ◽  
Structural Changes ◽  
Radiation Energy ◽  
Degree Of Crystallinity ◽  
Scanning Calorimetry ◽  
Polyether Ether Ketone ◽  
Ether Ketone ◽  
The Impact ◽  
The Degree Of Crystallinity

The article presents the results of research on the impact of structural changes in polyether ether ketone (PEEK) on its mechanical properties. The polymer was exposed to gamma radiation at a dose of 50 and 150 kGy, and the radiation energy was 4 MeV. Changes in the degree of crystallinity and the related changes in the glass transition and melting temperature for the polymer were determined by differential scanning calorimetry (DSC). Mechanical properties were determined using the micro-mentoring method. The tests showed a change in the degree of crystallinity in the range of several degrees and a significant increase in the glass transition temperature. In terms of mechanical properties, the reduction of hardness and Young’s modulus was observed. Observed changes, especially in terms of changes in the structure of the polymer under the influence of radiation, are difficult to explain, which requires conducting further research, especially in the range of irradiation parameters used. Further research is important because PEEK is used in many fields, especially in conditions conducive to corrosion and the influence of radiation.

Sign in / Sign up

Export Citation Format

Share Document