scholarly journals PERANCANGAN DAN PEMBUATAN PENGGERAK MEKANIK SATU SUMBU PADA SOLAR PANEL

2017 ◽  
Vol 5 (1) ◽  
Author(s):  
I Gusti Lanang Yoga Rafsandita ◽  
Gede Widayana ◽  
I Wayan Sutaya
Keyword(s):  
Solar Radiation ◽  
Power Plants ◽  
Solar Power ◽  
Elevation Angle ◽  
Solar Panel ◽  
Director General ◽  
The Sun ◽  
Solar Panels ◽  
Panel Type ◽  
Nominal Voltage

Indonesia merupakan negara yang memiliki berbagai jenis sumber daya energi dalam jumlah yang cukup melimpah. Wilayah Indonesia akan selalu disinari matahari selama 10 - 12 jam dalam sehari. Data Dirjen Listrik dan Pengembangan Energi pada tahun 1997, kapasitas terpasang listrik tenaga surya di Indonesia mencapai 0,88 MW dari potensi yang tersedia 1,2 x 109 MW. Kebanyakan panel surya dipasang permanen dengan sudut elevasi yang tetap (fixed elevating angles). Hal ini menyebabkan panel surya tersebut tidak dapat menyerap radiasi matahari secara optimal. Penyerapan radiasi matahari akan optimal jika arah radiasi matahari tegak lurus terhadap permukaan bidang panel surya. Penulis tertarik untuk merancang dan membuat alat yang dapat dipergunakan untuk menempelkan panel sel surya tetap dalam kondisi intensitas matahari yang maksimum. Dalam hal ini, menggunakan satu sumbu. dengan telah dibuatnya alat penggerak mekanik satu sumbu pada solar panel ini, penulis dapat memberikan gambaran tentang pembangkit listrik tenaga surya kepada masyarakat. Selain itu dengan adanya penggerak mekanik pada solar panel ini, solar panel bisa lebih besar menghasilkan tegangan pada baterai daripada solar panel tanpa penggerak. Dan dari percobaan menggunakan penggerak mekanik satu sumbu ini menghasilkan tegangan di pukul 08.00 pada baterai nominal sebesar 2,04V hari pertama, 2,05V hari kedua dan 2,03V hari ketiga dan di akhir perhitungan pukul 16.00 tegangan pada baterai menujukan nominal sebesar 11,18V hari pertama, 11,27V hari kedua dan 11,3V hari ketiga.Kata Kunci : Solar Panel, Tipe BCT30-12, Penggerak Satu Sumbu Indonesia is a country that has different kinds of energy resources in sufficient quantities abundant. then Indonesia will be always exposed to the sun for 10-12 hours a day. Data Director General of Electricity and Energy Development in 1997, the installed capacity of solar power in Indonesia reached 0.88 MW of the available potential of 1.2 x 109 MW. Most solar panels are installed permanently at a fixed elevation angle (fixed elevating angles). This causes the solar panels can not absorb solar radiation optimally. Absorption of solar radiation would be optimal if the solar radiation direction perpendicular to the surface of solar panel field. Writers interested in designing and creating tools that can be used to attach the solar panels remain in a state of maximum intensity of the sun. In this case, using a single axis. to have made a mechanical actuator on the solar panel one axis, the author can give an idea of solar power plants to the public. In addition to the mechanical drive on the solar panels, the solar panels generate voltage can be larger than the solar panel to the battery without driving. And from experiments using mechanical drive one axis produces a voltage at 08.00 at a total nominal battery 2,04V first day, 2,05V 2,03V second day and third day and at the end of the calculation 16.00 nominal voltage of the battery addressed by 11,18V the first day, 11,27V 11,3V second day and third day.keyword : Solar Panel, Type BCT30-12, Activator One Wick

scholarly journals Pemanfaatan Pembangkit Listrik Tenaga Surya Pada Gedung Bertingkat

Kilat ◽  
2020 ◽  
Vol 9 (1) ◽  
pp. 115-124
Author(s):  
Tri Joko Pramono ◽  
Erlina Erlina ◽  
Zainal Arifin ◽  
Jef Saragih
Keyword(s):  
Solar Radiation ◽  
Power Plants ◽  
Solar Power ◽  
Electrical Energy ◽  
Solar Panel ◽  
Performance Ratio ◽  
Solar Panels ◽  
Aesthetic Value ◽  
High Rise ◽  
Solar Power Plants

Solar Power Plant is one of the New Renewable Energy power plants. Solar panels can produce unlimited amounts of electrical energy directly taken from the sun, with no rotating parts and no fuel. In this study are optimize solar power plants using hybrid systems with electricity companies and the use of semi-transparent solar panels in high rise buildings to meet the burden of the building. The research will discussed about use of solar power plants using semi-transparent solar panels in multi-storey buildings. The solar panel used for the facade is a semi-transparent solar panel makes its function become two, that is to produce electrical energy as well as glass through which sunlight and can see the view outside the building without reducing the building's aesthetic value. In this study is the value of solar radiation taken from west is the lowest value in November 1.4 Kwh can produce energy PLTS 3,855 Kwh and the highest solar radiation in July amounted to 3.75 Kwh can produce energy PLTS 10.331 Kwh. From the utilization of this PLTS system, Performance Ratio of 85% was obtained using study of 36 panels on the 3rd to 5th floors, this system can be said to feasible.  

scholarly journals Comparison of Solar Radiation Torque and Power Generation of Deployable Solar Panel Configurations on Nanosatellites

Aerospace ◽  
2019 ◽  
Vol 6 (5) ◽  
pp. 50 ◽  
Author(s):  
Syahrim Azhan Ibrahim ◽  
Eiki Yamaguchi
Keyword(s):  
Power Generation ◽  
Solar Radiation ◽  
Solar Power ◽  
Solar Panel ◽  
Solar Array ◽  
The Sun ◽  
Solar Panels ◽  
Solar Power Generation ◽  
Software Algorithms ◽  
Selection Of

Nanosatellites, like CubeSat, have begun completing advanced missions that require high power that can be obtained using deployable solar panels. However, a larger solar array area facing the Sun increases the solar radiation torque on the satellite. In this study, we investigated solar radiation torque characteristics resulting from the increased area of solar panels on board the CubeSats. Three common deployable solar panel configurations that are commercially available were introduced and their reference missions were established for the purpose of comparison. The software algorithms used to simulate a variety of orbit scenarios are described in detail and some concerns are highlighted based on the results obtained. The solar power generation of the respective configurations is provided. The findings are useful for nanosatellite developers in predicting the characteristics of solar radiation torques and solar power generation that will be encountered when using various deployable solar panels, thus helping with the selection of a suitable configuration for their design.

Design and Implementation of Dual-Axis Solar Tracking System with GSM Fault Reporting Capability

2013 ◽  
Vol 724-725 ◽  
pp. 43-51 ◽  
Author(s):  
Yu En Wu ◽  
Kuo Chan Huang
Keyword(s):  
Power System ◽  
Power Efficiency ◽  
Solar Power ◽  
Tracking System ◽  
Elevation Angle ◽  
Azimuth Angle ◽  
The Sun ◽  
Solar Panels ◽  
Sensing Element ◽  
Solar Tracking

This paper presents a smart dual-axis solar tracking system, its architecture includes sensors, embedded controllers, AC motors, Integrated electric putter design biaxial institutions, and the GSM automatic report of fault notification, to achieve autonomous tracking solar track system and adjust the solar panels to reach the maximum smooth by tracking the solar azimuth angle and elevation angle, and ensure that the solar panels with the sun to maintain the vertical in any time and any place, thus achieving the best power efficiency. This system proposed a dual-axis design, and an embedded controller used as the main system controller to detect voltage difference and determine the solar azimuth angle with four groups of CDS as a sensing element. To lock the sun, the solar panels be perpendicular via the moving of AC motor (EW) and motorized faders (north-south). The control system software using C language can be extremely fast and accurate tracking of the solar angle, and dual-axis operation with recovery mode to save the power loss. Finally, we have the actual analysis and verification of benefit of power generation in this paper, from this experimental results, we can verify the integration of build dual-axis solar tracking system and solar power system have promoted 30% generating power capacity more than fixed solar power system and has low failure rate. It can improve the problem of traditional tracking system reliability and greatly enhance the usefulness of this system.

scholarly journals The Use of Inverters in Solar Power Plants for Alternating Current Loads

2021 ◽  
Vol 3 (3) ◽  
pp. 151-158
Author(s):  
Noorly Evalina ◽  
Faisal Irsan Pasaribu ◽  
Abdul Azis H
Keyword(s):  
Power Plants ◽  
Solar Power ◽  
Voltage Drop ◽  
Alternating Current ◽  
The Sun ◽  
Solar Panels ◽  
Output Current ◽  
Solar Power Plants ◽  
The Government ◽  
Led Lights

The sun shines on the territory of Indonesia for about 10 to 12 hours every day, so that solar power plants can be developed in Indonesia, the government has launched the movement of one million PLTS roofs in 2017, this research uses solar panels with a capacity of 200 Wp, which consists of 2 solar panels connected in parallel, solar charge controllers, batteries, inverters and as an AC load a fan, soldering iron and LED lights, the research aims to determine the output current, voltage and output power of the inverter when given an alternating current load that is inductive, resistive and capacitive, the method used is to measure the intensity of the sun, temperature, voltage, electric current, power factor, when the load is large the voltage drops depending on the given load, the inductive fan load has a voltage drop that is greater than the voltage drop that occurs in the soldering load and the LED lamp, the large current flowing on the output side fan load wants to be bigger than output current flowing in the solder and LED lights, the low efficiency of the inverter used can shorten the life of the electrical equipment used.

scholarly journals Experimental Study on The Effect of Arches Setting on Semi-Flexible Monocrystalline Solar Panels

2020 ◽  
pp. 111-118
Author(s):  
Iwan Arissetyadhi ◽  
Tresna Dewi ◽  
RD Kusumanto
Keyword(s):  
Experimental Study ◽  
Renewable Energy ◽  
Rainy Season ◽  
Solar Power ◽  
Dry Season ◽  
Solar Panel ◽  
The Sun ◽  
Solar Panels ◽  
Energy Potential ◽  
Convex Setting

Indonesia has a high potential for renewable energy, especially solar power, due to its location in the equator and blessed with an abundance of sunlight. However, the energy potential from the sun is not maximally utilized. One of the efforts to increase the generated electricity and efficiency is by applied the panels in arches setting. This setting is made possible by the availability of the semi-flexible monocrystalline solar panel. This paper investigates the increment of harvested power and efficiency by arranging the solar panel in concave, convex, and plane settings. The data were taken in August 2019, where Palembang experiences the dry season and January 2020 during the rainy season. The highest power produced (20.27 Watt) and efficiency (13.14%) were achieved in a concave setting during the dry season. The convex setting produced more power and efficiency (13.26 Watt and 9.30%) compared to the plane setting (10.24 Watt and 9.71%). These results show that arches setting are more efficient to harvest solar power and give more extensive applications such as to power a dynamics mobile robot applied in agriculture.

scholarly journals SIMULASI DAN PEMBUATAN RANGKAIAN SISTEM KONTROL PENGISIAN BATERAI UNTUK PEMBANGKIT LISTRIK TENAGA SURYA

2016 ◽  
Vol 16 (1) ◽  
pp. 30
Author(s):  
Handy Indra Regain Mosey
Keyword(s):  
Control System ◽  
Power Plants ◽  
Solar Power ◽  
Circuit Simulation ◽  
Solar Panel ◽  
Solar Panels ◽  
Battery Charging ◽  
Charging Control ◽  
Control Switch ◽  
Solar Power Plants

ABSTRAK Paper ini membahas tentang simulasi dan pembuatan rangkaian sistem kontrol pengisian baterai yang bersumber dari sebuah pembangkit listrik tenaga surya (Panel Surya). Pengisian baterai yang terlalu lama pada sebuah instalasi pembangkit listrik tenaga surya akan menyebabkan baterai cepat rusak sehingga dibutuhkan sebuah sistem yang dapat berfungsi sebagai pengontrol. Metode penelitian yang dilakukan yaitu dengan merangkai rangkaian yang didapat dari pustaka kemudian disimulasikan dengan perangkat lunak Proteus ISIS Profesional, selanjutnya dilakukan pembuatan rangkaian elektronika dalam sebuah PCB. Tegangan yang dihasilkan oleh baterai dibaca oleh sistem kontrol kemudian sistem akan memilih apabila tegangan yang diberikan oleh panel surya akan diisi pada baterai atau dialihkan kepada sebuah beban tambahan. Hasil yang didapatkan dalam penelitian menunjukan bahwa sistem kontrol pengisian baterai yang dibangun telah bekerja sesuai dengan simulasi dan dapat bekerja dengan baik. Kata-kata kunci: sistem kontrol baterai, switch, panel surya. SIMULATION AND CONSTRUCTION OF A BATTERY CHARGING CONTROLLER SYSTEM FOR SOLAR POWER PLANTS ABSTRACT This paper discusses about circuit simulation and construction of a battery charging control system from a solar power plant (Solar Panels). Charging the battery for too long on an installation of solar power plants will cause the battery to be broken and so we need a system that can function as a controller. The research method is made by simulating a baterry charging control circuit from a reference and then simulated by Proteus ISIS Professional software, then constructing the circuit on a PCB. The voltage produced by the solar panel is read by the control system then the system will prefer if the voltage supplied by the solar panels will be filled on the battery or transferred to an additional load. Result obtained in this study indicate that the baterry charging control system are working in accordance with the software simulation and can work as a baterry charging control system for a solar panel instalation. Keywords: Baterry charging control, switch, solar panel.

Optimization Circuit Based Buck-Boost Converter for Charging the Solar Power Plant

2017 ◽  
Vol 6 (2) ◽  
pp. 254
Author(s):  
Rohana Rohana ◽  
Suwarno Suwarno
Keyword(s):  
Power Plants ◽  
Solar Power ◽  
Boost Converter ◽  
Solar Panel ◽  
Voltage Stabilizer ◽  
Solar Panels ◽  
Output Current ◽  
Battery Charging ◽  
Current Rise ◽  
Battery Chargers

<p>This paper discusses the optimization circuit based buck-boost converter for charging a battery from solar panel modules. The combination of the circuit buck-bust converter and a step-up current can increase the percentage of battery chargers. The method used in the optimization of solar power plants by increasing the output current from the solar panel to be optimized for battery charging, so it does not requires time and the batteries are safe. This is because sunlight can be used when bright about 4-5 hours per day. By increasing the output current of the current produced solar modules can accelerate the battery charging time. The combination of using the voltage stabilizer can produce a steady output voltage and current riser, although the voltage to an output of the solar panels is quite small (± 6 volts), can optimize the charger works well. By combining between the voltage stabilizer and a step-up current is obtained that the incoming voltage to the battery at 12,4V the current rise of 21.5% for a 12V battery, 7Ah, whereas the incoming voltage to the battery at 12,1V the current rise 10.99% for battery 12V, 120Ah. This study shows that the current rise is already above 10%.</p>

scholarly journals Increasing the Efficiency Factor of Solar Power Plants Due to Solar Energy Localizing

2021 ◽  
Vol 64 (1) ◽  
pp. 15-26
Author(s):  
V. I. Mironchuk ◽  
A. A. Velchenko
Keyword(s):  
Solar Energy ◽  
Power Plants ◽  
Solar Power ◽  
Geographic Area ◽  
Efficiency Factor ◽  
The Sun ◽  
Solar Panels ◽  
Solar Power Plants ◽  
The Republic ◽  
The City

The article presents an analysis of the state of development of solar energy in Europe and  the  Republic  of  Belarus  for 2020.  An algorithm for increasing the efficiency factor of  solar power plants by localizing the solar trajectory depending on the latitude and longitude of the area has been proposed. In particular, taking into account the angle of the Sun position above the horizon and the azimuth angle of the Sun, the increase in the efficiency factor of solar power plants for the Republic of Belarus is calculated. Based on this algorithm, a program has been written that makes it possible to draw a diagram of the solar trajectory. An analysis has been made of the degree of localization of solar energy for solstice days in 6 oblast (regional) centers of the Republic of Belarus; it is found that the highest intensity of solar radiation is observed in Brest and Gomel, the average in Grodno, Minsk and Mogilev, while the lowest one – in the city of Vitebsk. A comparative analysis of the solar trajectory of the city of Berlin (Germany) with the city of Gomel and the city of Brest is carried out. Recommendations have been developed for the effective operation of solar power plants in the oblast (regional) cities of the Republic of Belarus during the year in an autonomous and combined mode of operation. The obtained numerical calculations of the solar trajectory make it possible to optimize the orientation of solar panels for permanently installed panels and for automated solar tracking systems, as well as to select the optimal configuration of the power plant equipment for any geographic area.

scholarly journals Solar Panels and their Diverse Characteristics: An All-Inclusive Study

2021 ◽  
Vol 11 (4) ◽  
pp. 4456-4464
Author(s):  
S.V.G.V.A. Prasad
Keyword(s):  
Solar Energy ◽  
Electricity Generation ◽  
Fossil Fuels ◽  
Solar Power ◽  
Electrical Energy ◽  
Clean Energy ◽  
Solar Panel ◽  
Electricity Production ◽  
The Sun ◽  
Solar Panels

In recent years the use of solar energy is found to have grown by a large amount. Solar energy is renewable energy and the demand for it as clean energy shows its growth by nearly 50 percent in the past decade. It is estimated that the sun is able to generate energy within 24 hours that the entire population of the world could consume in 27 years. Solar power is the energy from the sun that is converted into thermal or electrical energy. The energy harnessed from the sun's rays is used for a variety of applications like electricity generation, to provide light for the interior environment, and many other domestic, commercial, and industrial purposes. Usage of fossil fuels for electricity production results in increased pollution and this mandates many governments to encourage moving to electricity generation using solar power. The large amount of solar energy that is available is found to be the most appealing source of electricity. Solar panels form a major part of the solar energy setup. Hence in this article let us review the various types of solar panels. This paper also deals with comparing the merits and demerits of the different types of solar panels that are available in the market. A section that presents the efficiency of the different kinds of the solar panel is also present in this paper. The role of temperature coefficient, fire rating, and hail rating in the performance of the solar panel is also addressed in this paper.

Sign in / Sign up

Export Citation Format

Share Document