Response fitting in low-cost radiation sensors

ABSTRACTThe massive crystal growth of single crystal semiconductors materials has been of fundamental importance for the actual electronic devices industry. As a consequence of this one, we can obtain easily a large variety of low cost devices almost as made ones of silicon. Nowadays, the III-V semiconductors compounds and their alloys have been proved to be very important because of their optical properties and applications. It is the case of the elements In, Ga, As, Sb, which can be utilized for the fabrication of radiation sensors. In this work we present the results obtained from the ingots grown by the Czochralski method, using a growth system made in home. These results include anisotropic chemical attacks in order to reveal the crystallographic orientation and the possible polycrystallinity. Isotropic chemical attacks were made to evaluate the etch pit density. Metallographic pictures of the chemical attacks are presented in this work. Among the results of these measurements, the best samples presented in this work showed mobilities of 62.000 cm2/V*s at room temperature and 99.000 cm2/V*s at liquid nitrogen temperature. Typical pit density was 10,000/cm2. The Raman spectra present two dominant peaks associated at Transversal Optical (TO)- and Longitudinal Optical (LO)-InSb, the first vibrational mode is dominant due to the crystalline direction of the ingots and second one is associated to high defects density.

Download Full-text

SmartKC

Proceedings of the ACM on Interactive Mobile Wearable and Ubiquitous Technologies ◽

10.1145/3494982 ◽

2021 ◽

Vol 5 (4) ◽

pp. 1-27

Author(s):

Siddhartha Gairola ◽

Murtuza Bohra ◽

Nadeem Shaheer ◽

Navya Jayaprakash ◽

Pallavi Joshi ◽

...

Keyword(s):

Low Cost ◽

Pearson Correlation ◽

Step Method ◽

Middle Income ◽

Middle Income Countries ◽

Large Populations ◽

Pixel Location ◽

3D Printed ◽

Working Distance ◽

Fitting In

Keratoconus is a severe eye disease affecting the cornea (the clear, dome-shaped outer surface of the eye), causing it to become thin and develop a conical bulge. The diagnosis of keratoconus requires sophisticated ophthalmic devices which are non-portable and very expensive. This makes early detection of keratoconus inaccessible to large populations in low-and middle-income countries, making it a leading cause for partial/complete blindness among such populations. We propose SmartKC, a low-cost, smartphone-based keratoconus diagnosis system comprising of a 3D-printed placido's disc attachment, an LED light strip, and an intelligent smartphone app to capture the reflection of the placido rings on the cornea. An image processing pipeline analyzes the corneal image and uses the smartphone's camera parameters, the placido rings' 3D location, the pixel location of the reflected placido rings and the setup's working distance to construct the corneal surface, via the Arc-Step method and Zernike polynomials based surface fitting. In a clinical study with 101 distinct eyes, we found that SmartKC achieves a sensitivity of 87.8% and a specificity of 80.4%. Moreover, the quantitative curvature estimates (sim-K) strongly correlate with a gold-standard medical device (Pearson correlation coefficient = 0.77). Our results indicate that SmartKC has the potential to be used as a keratoconus screening tool under real-world medical settings.

Download Full-text

A Novel X-Ray Radiation Sensor Based on Networked SnO2 Nanowires

Applied Sciences ◽

10.3390/app9224878 ◽

2019 ◽

Vol 9 (22) ◽

pp. 4878 ◽

Cited By ~ 5

Author(s):

Jae-Hun Kim ◽

Ali Mirzaei ◽

Hyoun Woo Kim ◽

Hong Joo Kim ◽

Phan Quoc Vuong ◽

...

Keyword(s):

Electron Microscopy ◽

Room Temperature ◽

Low Cost ◽

X Rays ◽

X Ray Diffraction ◽

X Ray ◽

Transmission Electron ◽

Radiation Sensor ◽

Sno2 Nanowires ◽

Radiation Sensors

X-Ray radiation sensors that work at room temperature are in demand. In this study, a novel, low-cost real-time X-ray radiation sensor based on SnO2 nanowires (NWs) was designed and tested. Networked SnO2 NWs were produced via the vapor–liquid–solid technique. X-ray diffraction (XRD), transmission electron microscopy (TEM) and field emission scanning electron microscopy (SEM) analyses were used to explore the crystallinity and morphology of synthesized SnO2 NWs. The fabricated sensor was exposed to X-rays (80 kV, 0.0–2.00 mA) and the leakage current variations were recorded at room temperature. The SnO2 NWs sensor showed a high and relatively linear response with respect to the X-ray intensity. The X-ray sensing results show the potential of networked SnO2 NWs as novel X-ray sensors.

Download Full-text

Assessment and Correction of Solar Radiation Measurements with Simple Neural Networks

Atmosphere ◽

10.3390/atmos11111160 ◽

2020 ◽

Vol 11 (11) ◽

pp. 1160

Author(s):

Jason Kelley

Keyword(s):

Neural Networks ◽

Solar Radiation ◽

Low Cost ◽

Environmental Data ◽

Data Driven ◽

Technical Requirements ◽

Standard Procedures ◽

Comparable Accuracy ◽

Radiation Sensors ◽

Radiation Measurements

Solar radiation received at the Earth’s surface provides the energy driving all micro-meteorological phenomena. Local solar radiation measurements are used to estimate energy mediated processes such as evapotranspiration (ET); this information is important in managing natural resources. However, the technical requirements to reliably measure solar radiation limits more extensive adoption of data-driven management. High-quality radiation sensors are expensive, delicate, and require skill to maintain. In contrast, low-cost sensors are widely available, but may lack long-term reliability and intra-sensor repeatability. As weather stations measure solar radiation and other parameters simultaneously, machine learning can be used to integrate various types of environmental data, identify periods of erroneous measurements, and estimate corrected values. We demonstrate two case studies in which we use neural networks (NN) to augment direct radiation measurements with data from co-located sensors, and generate radiation estimates with comparable accuracy to the data typically available from agro-meteorology networks. NN models that incorporated radiometer data reproduced measured radiation with an R2 of 0.9–0.98, and RMSE less than 100 Wm−2, while models using only weather parameters obtained R2 less than 0.75 and RMSE greater than 140 Wm−2. These cases show that a simple NN implementation can complement standard procedures for estimating solar radiation, create opportunities to measure radiation at low-cost, and foster adoption of data-driven management.

Download Full-text

A Custom-built Scanner for the Estimation of the Radiation Intercepted by a Tree Canopy

HortScience ◽

10.21273/hortsci.32.3.531d ◽

1997 ◽

Vol 32 (3) ◽

pp. 531D-531

Author(s):

Rita Giuliani ◽

Eugenio Magnanini ◽

Luca Corelli Grappadelli

Keyword(s):

Low Cost ◽

Ground Surface ◽

Step Length ◽

Tree Canopy ◽

Photon Flux ◽

Data Logger ◽

The Difference ◽

Main Components ◽

Mathcad Software ◽

Radiation Sensors

This work proposes a methodology, by light-scanning below the canopy, to directly estimate the photon flux radiation (400–1200 nm) intercepted by single or row canopies. The system is based on the assumption that the light intercepted by the canopy, at a particular time, corresponds to the difference between the incoming potential radiation on a ground surface area (able to include the ground area shaded by the canopy), and the actual radiation influx to that area in presence of the canopy. To this purpose, light-scanning equipment has been designed, built, and tested, whose main components are two aligned multi-sensor bars (1.2 m long) and a CR10 data logger, equipped with an AM 416 Relay Multiplexer (Campbell Sci. Ltd., U.K.). The radiation sensors (BPW 14N TELEFUNKEN) were chosen because of their spectral sensitivity, along with low cost. The sensors have been placed along the bars, at 5-cm intervals, and fitted with a Teflon® diffuser to provide a cosine correction. Radiation measurements are taken moving parallelly the bars on the ground, step by step, to monitor a sample point grid (5 cm by step length). Preliminary radiation scans were taken during the summer in a 3-year-old peach orchard, trained as delayed vasette. Measurements were taken for a single canopy at various hours of the day. Moreover, radiation scans were taken at the same hour, over a 3-day timespan, while gradually defoliating the canopy. A custom-built software program has been developed for data handling. Mathcad software (Mathsoft Inc., U.S.) has been used to display the canopy shade image projected on the ground, the quantum map of the monitored area, and to calculate the light influx on the whole canopy. Moreover, the light spots on the ground determined by foliage gaps have been identified and the amount of radiation reaching the ground has been be estimated.

Download Full-text

A High Sensitivity Temperature Sensing Probe Based on Microfiber Fabry-Perot Interference

Sensors ◽

10.3390/s19081819 ◽

2019 ◽

Vol 19 (8) ◽

pp. 1819 ◽

Cited By ~ 11

Author(s):

Zhoubing Li ◽

Yue Zhang ◽

Chunqiao Ren ◽

Zhengqi Sui ◽

Jin Li

Keyword(s):

Low Cost ◽

High Sensitivity ◽

Single Mode ◽

Single Mode Fiber ◽

Temperature Sensing ◽

Compact Structure ◽

Fabry Perot ◽

Temperature Monitor ◽

Core Fiber ◽

Fitting In

In this paper, a miniature Fabry-Perot temperature probe was designed by using polydimethylsiloxane (PDMS) to encapsulate a microfiber in one cut of hollow core fiber (HCF). The microfiber tip and a common single mode fiber (SMF) end were used as the two reflectors of the Fabry-Perot interferometer. The temperature sensing performance was experimentally demonstrated with a sensitivity of 11.86 nm/°C and an excellent linear fitting in the range of 43–50 °C. This high sensitivity depends on the large thermal-expansion coefficient of PDMS. This temperature sensor can operate no higher than 200 °C limiting by the physicochemical properties of PDMS. The low cost, fast fabrication process, compact structure and outstanding resolution of less than 10−4 °C enable it being as a promising candidate for exploring the temperature monitor or controller with ultra-high sensitivity and precision.

Download Full-text

Performance of Semiconductor Radiation Sensors for Simple and Low-cost Radiation Detector

RADIOISOTOPES ◽

10.3769/radioisotopes.57.733 ◽

2008 ◽

Vol 57 (12) ◽

pp. 733-738

Author(s):

Yoshihiko TANIMURA ◽

Atsushi BIRUMACHI ◽

Makoto YOSHIDA ◽

Tamaki WATANABE

Keyword(s):

Low Cost ◽

Radiation Detector ◽

Radiation Sensors

Download Full-text

Decomposition of the metastable beta titanium alloy Ti-15-3

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100075117 ◽

1983 ◽

Vol 41 ◽

pp. 264-265

Author(s):

Y. L. Chen ◽

S. Fujlshiro

Keyword(s):

Low Cost ◽

High Strength ◽

Alpha Phase ◽

Thick Sheet ◽

Omega Phase ◽

Beta Titanium Alloy ◽

Beta Titanium ◽

Beta Matrix ◽

Metastable Beta ◽

Very High

Metastable beta titanium alloys have been known to have numerous advantages such as cold formability, high strength, good fracture resistance, deep hardenability, and cost effectiveness. Very high strength is obtainable by precipitation of the hexagonal alpha phase in a bcc beta matrix in these alloys. Precipitation hardening in the metastable beta alloys may also result from the formation of transition phases such as omega phase. Ti-15-3 (Ti-15V- 3Cr-3Al-3Sn) has been developed recently by TIMET and USAF for low cost sheet metal applications. The purpose of the present study was to examine the aging characteristics in this alloy.The composition of the as-received material is: 14.7 V, 3.14 Cr, 3.05 Al, 2.26 Sn, and 0.145 Fe. The beta transus temperature as determined by optical metallographic method was about 770°C. Specimen coupons were prepared from a mill-annealed 1.2 mm thick sheet, and solution treated at 827°C for 2 hr in argon, then water quenched. Aging was also done in argon at temperatures ranging from 316 to 616°C for various times.

Download Full-text

Chromic Acid Etching of Polyethylene

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100070801 ◽

1973 ◽

Vol 31 ◽

pp. 72-73

Author(s):

J. D. Muzzy ◽

R. D. Hester ◽

J. L. Hubbard

Keyword(s):

Chromic Acid ◽

Low Cost ◽

Acid Etching ◽

Crystalline Morphology ◽

Bulk Specimen ◽

Morphological Studies ◽

Perfect Form ◽

Molecular Length ◽

Lamellar Texture ◽

Cost Studies

Polyethylene is one of the most important plastics produced today because of its good physical properties, ease of fabrication and low cost. Studies to improve the properties of polyethylene are leading to an understanding of its crystalline morphology. Polyethylene crystallized by evaporation from dilute solutions consists of thin crystals called lamellae. The polyethylene molecules are parallel to the thickness of the lamellae and are folded since the thickness of the lamellae is much less than the molecular length. This lamellar texture persists in less perfect form in polyethylene crystallized from the melt.Morphological studies of melt crystallized polyethylene have been limited due to the difficulty of isolating the microstructure from the bulk specimen without destroying or deforming it.

Download Full-text

Glass Knife Geometry as Seen by the SEM

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100066322 ◽

1971 ◽

Vol 29 ◽

pp. 454-455

Author(s):

J. Temple Black

Keyword(s):

Low Cost ◽

Amorphous Material ◽

Stress Concentrations ◽

Basic Tool ◽

Tool Materials ◽

Optical Inspection ◽

Surface Flaws ◽

Slip Planes ◽

Glass Knife ◽

Diamond Knife

In ultramicrotomy, the two basic tool materials are glass and diamond. Glass because of its low cost and ease of manufacture of the knife itself is still widely used despite the superiority of diamond knives in many applications. Both kinds of knives produce plastic deformation in the microtomed section due to the nature of the cutting process and microscopic chips in the edge of the knife. Because glass has no well defined slip planes in its structure (it's an amorphous material), it is very strong and essentially never fails in compression. However, surface flaws produce stress concentrations which reduce the strength of glass to 10,000 to 20,000 psi from its theoretical or flaw free values of 1 to 2 million psi. While the microchips in the edge of the glass or diamond knife are generally too small to be observed in the SEM, the second common type of defect can be identified. This is the striations (also termed the check marks or feathers) which are always present over the entire edge of a glass knife regardless of whether or not they are visable under optical inspection. These steps in the cutting edge can be observed in the SEM by proper preparation of carefully broken knives and orientation of the knife, with respect to the scanning beam.

Download Full-text