scholarly journals On problem of calculating longitudinal vibrations of piston engine crankshaft

2021 ◽  
Vol 2021 (4) ◽  
pp. 75-83
Author(s):  
Alexander Ivanovich Yamanin ◽  
Vladimir Anatoljevich Zhukov
Keyword(s):  
Oscillatory System ◽  
Radial Force ◽  
Regression Equations ◽  
Connecting Rod ◽  
Longitudinal Vibrations ◽  
Empirical Formulas ◽  
Disturbing Force ◽  
Calculation Results ◽  
Engine Crankshaft

One of the initial stages of calculating the crankshaft longitudinal vibrations is developing an oscillatory system model, which includes the determination of longitudinal pliability (rigidity) of elastic sections. If it is impossible to determine the pliability experimental, the empiric formulas or the final element method (FEM) are used. There are given the values of crank longitudinal pliability of the crankshafts of different marine engine types found by using the formulas of L. Gugliemotti – R. Machciotta, P. Draminsky, E. Y. Gorbunov, S. F. Dorey, N. S. Skorchev, V. S. Stoyanov, etc. It is shown that the calculation results obtained from these formulas for the same engine significantly differ; therefore, the choice of one or another empirical formula for practical calculations is difficult. The preference of using FEM for determining the longitudinal (axial) compliance of cranks and other areas with complex geometric shapes has been proven. The possibility of its application is also shown to determine the longitudinal disturbing force as the reaction of the crankshaft support against the action of the radial force exerted to the connecting rod journal. It is proposed to use, along with empirical formulas, regression equations connecting the longitudinal compliance of the cranks with a significantly larger number of their design dimensions.

scholarly journals Determination of Parameters of Grates on Rubber Brackets of Fiber Material Cleaners

2019 ◽  
Vol 9 (2) ◽  
pp. 4263-4270
Keyword(s):  
Fibrous Material ◽  
Vertical Mixing ◽  
Fiber Material ◽  
Regression Equations ◽  
Mass System ◽  
Disturbing Force ◽  
Single Mass ◽  
Determination Of Parameters ◽  
Full Factorial

The article shows the installation scheme of the grate and the principle of operation of the cleaner of fibrous material from large litter. The oscillation of the grates installed in the upper and lower cleaning zones with different thickness of the rubber support was studied. On the basis of theoretical studies of the grate in the form of a single-mass system, regularities of the change in vertical mixing and speeds of grates are obtained. Graphical dependences of the change in the amplitude of oscillations of the mixes and the speeds of the grate are constructed on the variation of the mass of the grate, the disturbing force on the cotton being revealed, and also on the stiffness coefficient of the elastic support. Full-factorial experiments obtained regression equations. By solving the problem, graphical dependencies of the change in the cleansing effect on incoming factors are constructed. The analyzes substantiate the parameters of the fibrous material cleaner.

DETERMINATION OF THE FUNCTION OF THE ROD’S CROSS-SECTIONAL AREA USING VIBRATION EIGENFREQUENCIES

2020 ◽  
Vol 0 (4) ◽  
pp. 19-24
Author(s):  
I.M. UTYASHEV ◽  
◽  
A.A. AITBAEVA ◽  
A.A. YULMUKHAMETOV ◽  
◽  
...  
Keyword(s):  
Cross Sectional Area ◽  
Variable Cross ◽  
Sectional Area ◽  
Longitudinal Vibrations ◽  
Cross Sectional ◽  
Method Error ◽  
Various Boundary Conditions ◽  
Elastic Fixation ◽  
Crosssectional Area

The paper presents solutions to the direct and inverse problems on longitudinal vibrations of a rod with a variable cross-sectional area. The law of variation of the cross-sectional area is modeled as an exponential function of a polynomial of degree n . The method for reconstructing this function is based on representing the fundamental system of solutions of the direct problem in the form of a Maclaurin series in the variables x and λ. Examples of solutions for various section functions and various boundary conditions are given. It is shown that to recover n unknown coefficients of a polynomial, n eigenvalues are required, and the solution is dual. An unambiguous solution was obtained only for the case of elastic fixation at one of the rod’s ends. The numerical estimation of the method error was made using input data noise. It is shown that the error in finding the variable crosssectional area is less than 1% with the error in the eigenvalues of longitudinal vibrations not exceeding 0.0001.

Methodology of Estimation of Fire Separation Distances between Construction Facilities by Calculation

2020 ◽  
Vol 1006 ◽  
pp. 93-100
Author(s):  
Vadym Nizhnyk ◽  
Yurii Feshchuk ◽  
Volodymyr Borovykov
Keyword(s):  
Mathematical Model ◽  
Heat Flux ◽  
Linear Regression ◽  
Ignition Temperature ◽  
Oil Products ◽  
Regression Equations ◽  
Fire Load ◽  
Literary Sources ◽  
Tabular Method

Based on analysis of appropriate literary sources we established that estimation of fire separation distances was based of two criteria: heat flux and temperature. We proposed to use “ignition temperature of materials” as principal criterion when determining fire separation distances between adjacent construction facilities. Based on the results derived while performing complete factorial we created mathematical model to describe trend of changing fire separation distances depending on caloric power of fire load (Q), openings factor of the external enclosing structures (k) and duration of irradiation (t); moreover, its adequacy was confirmed. Based on linear regression equations we substantiated calculation and tabular method for the determination of fire separation distances for a facility being irradiated which contains combustible or otherwise non-combustible façade and a facility where liquid oil products turn. We developed and proposed general methodology for estimation of fire separation distances between construction facilities by calculation.

Optimization of a Specimen Size for the Determination of the Diffusible Hydrogen Content in Metals

2014 ◽  
Vol 698 ◽  
pp. 466-471
Author(s):  
Oleg V. Panchenko ◽  
Alexey M. Levchenko ◽  
Victor A. Karkhin
Keyword(s):  
Hydrogen Content ◽  
Calculation Method ◽  
Specimen Size ◽  
Experimental Results ◽  
Diffusible Hydrogen ◽  
Measuring Methods ◽  
Deposited Metal ◽  
Calculation Results

Specimens of various sizes are used to determine hydrogen content in deposited metals in such standards as ISO 3690, AWS A 4.3, and GOST 23338 while measuring methods are the same. It causes problems in comparison of experimental results and brings up the following question: what kind of specimen size is optimal to determine hydrogen content? An optimal specimen size was estimated using a calculation method. Experimental and calculation results obtained by using specimens with estimated dimensions were compared to the results obtained by using the specimen with dimensions of 100*25*8 mm to determine hydrogen content in a deposited metal.

scholarly journals Determination of Nearest Emergency Service Office using Haversine Formula Based on Android Platform

2018 ◽  
Vol 5 (2) ◽  
pp. 270-278 ◽  
Author(s):  
M. Basyir ◽  
M. Nasir ◽  
Suryati Suryati ◽  
Widdha Mellyssa
Keyword(s):  
Emergency Service ◽  
Emergency Services ◽  
Message Delivery ◽  
Test Results ◽  
Average Delay ◽  
Accuracy Test ◽  
Calculation Results ◽  
Testing Accuracy ◽  
Selection Of

Emergency Reporting Application is an android-based application that serves to help the community in reporting the emergency condition. This application allows users to choose and contact the emergency services office, without the need to notice their position and phone number. Selection of emergency services office is also automatically selected by the system by taking into account the distance between the complainant and the emergency services office. The selected emergency services office is the nearest emergency service office from the complainant so that the delay in coming assistance can be minimized. Therefore, this proposed application requires a GPS feature to recording, reporting and SMS positioning for message delivery of reports. The distance between the position of the complainant and the position of the emergency service office, in the form of latitude and longitude data, is requested using the Haversine formula taking into account the degree of curvature of the earth. Emergency service offices include police and hospital offices spread over 25 different districts. Furthermore, the reporter's position calculation results were compared with all selected emergency service offices and obtained 1 nearest emergency service office. Calculating the accuracy and delay value of the system will do system testing. Accuracy test results using the method of 100% Haversine and the average delay of the system is 4.5 seconds.

scholarly journals Investigation of Complex Structural Designing of Mobile Facilities for Shipbuilding in Lithuanian Sea Region

Mechanika ◽  
2021 ◽  
Vol 27 (3) ◽  
pp. 237-243
Author(s):  
Tadas ASTRAUSKAS ◽  
Michail SAMOFALOV
Keyword(s):  
Dynamic Analysis ◽  
Longitudinal Direction ◽  
Cross Sectional ◽  
Climatological Data ◽  
Second Stage ◽  
Third Stage ◽  
Calculation Results ◽  
Complex Structural ◽  
Mobile Facilities

In the paper, it is proposed to cover by a mobile moving facility the shipyard open site, in Klaipeda, Lithuania (the EU). The facility of 40 m span consists of transversal frames, which are arranged by the step of 6.0 m, and a system of braces. Two types of steel frames have been considered: trussed and continuous. The actions are specified according to the design codes (Eurocode 3) and climatological data. In dynamic analysis, the longitudinal direction is defined for an inertia action, simulating braking. For calculating, a special algorithm of three stages has been prepared. At the first stage, three calculation schemes of one transversal frame were created. For the proposed schemes of the mobile moving facility, the calculation of only a transversal frame is effective in the preliminary determination of the cross-sectional areas and of the total structural weight. At the second stage, the frames were joined by braces. A preliminary comparison of the calculation results of the models was carried out after the first and second stages of the analysis. At the third stage, the dynamic analysis was performed and the influence of the dynamic impact was estimated. Finally, we compared the calculation results of three different FEM models and chose the most appropriate one. To sum up the investigations, conclusions and recommendations are presented.

scholarly journals Kemampuan Lulusan Sekolah Tinggi Pariwisata Ampta Dalam Menghadapi Persaingan Di Dunia Kerja

Media Wisata ◽  
2021 ◽  
Vol 16 (1) ◽  
Author(s):  
Sri Larasati
Keyword(s):  
Communication Skill ◽  
Total Population ◽  
Sampling Technique ◽  
Regression Equations ◽  
Test Results ◽  
A Value ◽  
The Face ◽  
Job Competition ◽  
Sampling Approach

The purpose of this research is to know wtether knowledge, skill, responsiveness and communication skill influence in job competition for graduate student from Sekolah Tinggi Pariwisata AMPTA. The population in this study are student pf Sekolah Tinggi Pariwisata SMPTA that graduated in 2013 until 2016, the total population in this studt is 702 and 200 respondents who have worked taken as samples, samples were taken with non probability sampling technique and accidental sampling approach. Sampling approach using regression equations obtained results that through test results F (regression analysis jointly) may note that the value of F = 147.104 count with the significance of 0.000 < 0.05. The test results of the test F reinforced with testing the determination of the coefficient that shows the value of 74.6%) (0.746. From Test t (partially) can result in variable knowledge with a value of t = 3,173 and significance of the value 0002 < 0.05, variable skill with a value of t = 2,949 and value the significance of 0.004 < 0.05, variable attitude with a value of t = 2,688 and value the significance of 0.008 < 0.05, variable communication skill with a value of t = value and significance of 4,497 0000 < 0.05. From the above results can be known that the hypothesis posed was not proven in other words that all of these variables can be said to have a positive and significant effect simultaneously as well as partial toward the ability of STP graduates AMPTA in the face of competition in the world of work

scholarly journals Determination of individual teleroentgenographic characteristics of the face profile in ukrainian young men and girls with orthognathic bite

2018 ◽  
pp. 28-34
Author(s):  
М. О. Dmitriev
Keyword(s):  
Regression Analysis ◽  
Soft Tissue ◽  
Young Women ◽  
Stepwise Regression ◽  
Young Men ◽  
Stepwise Regression Analysis ◽  
Regression Equations ◽  
Determination Coefficient ◽  
Normal Occlusion

Modern dentistry requires the definition of individualized values of teleroentgenographic indicators. To solve such problems, methods of regression and correlation analysis are increasingly used, which help to establish not only the existence of various relationships between the anatomical structures of the head and the parameters of the dento-jaw system, but also allow more accurately predict the change in the contour of soft facial tissue in response to orthodontic treatment. The purpose of the study is to develop mathematical models for the determination of individual teleroentgenographic characteristics of the facial soft tissues by studying the cephalometric indices of young men and women of Ukraine with normal occlusion and balanced faces and conducting a direct stepwise regression analysis. With the use of Veraviewepocs 3D device, Morita (Japan) from 38 young men (17 to 21 years of age) and 55 young women (aged from 16 to 20 years) with occlusal close to the orthognathic bite and balanced faces received side teleroentgenograms. The cephalometric analysis was performed using OnyxCeph³™ licensed software. Cephalometric points and measurements were made according to the recommendations of Downs W. B., Holdway R. A., McNamara J., Schwarz A. M., Schmuth G. P. F., Steiner C. C. and Tweed C. H. With the help of direct stepwise regression analysis, in the licensed package “Statistica 6.0”, regression models of individual teleroentgenographic characteristics of the profile of soft facial tissues were constructed. In young men with normal occlusion close to the orthognathic bite of 19 possible models, 11 were constructed with a determination coefficient from 0.638 to 0.930, and in young women – 12 models with a determination coefficient from 0.541 to 0.927. The conducted analysis of models showed that in young men most often the regression equations included – angle N_POG, parameters of which indicate a linear interjaw relation in the anterior-posterior direction (14.0%); angle GL_SNPOG, or index of convexity of the soft tissue profile (8.8%); MAX maxillary length (7.0%), and GL_SN_S index, which defines vertical correlations in the facial profile (5.3%). The young women most often models included – the angle N_POG (12.5%); angle GL_SNPOG (7.5%); soft tissue front angle P_OR_N (6.25%); the reference angle ML_NL and the profile angle T (by 5.0%); the angle AB_NPOG, the angle NBA_PTGN, which defines the direction of development of the mandible and the distance PN_A (3.75%). Thus, in the work with the help of the method of stepwise regression with inclusion, among Ukrainians of adolescence age, based on the characteristics of teleroentgenographic indicators, reliable models of individual teleroentgenographic characteristics of the profile of soft facial tissues were developed and analyzed.

Sign in / Sign up

Export Citation Format

Share Document