scholarly journals Treatment of Leachate Using Up-Flow Anaerobic Sludge Blanket Reactors/Vertical Flow Subsurface Constructed Wetlands

2020 ◽  
Vol 27 (1) ◽  
pp. 129-137
Author(s):  
Şevket Tulun
Keyword(s):  
Total Nitrogen ◽  
Landfill Leachate ◽  
Oxygen Demand ◽  
Ammonia Nitrogen ◽  
Organic Content ◽  
Ammonia Removal ◽  
Anaerobic Sludge ◽  
Vertical Flow ◽  
Physico Chemical ◽  
Anaerobic Sludge Blanket

AbstractThe composition of local solid waste consists mainly of biodegradable waste with high moisture and organic content. After being landfilled, the waste decomposes through a series of combined physico-chemical and biological processes, resulting in the generation of landfill leachate. Unless treated properly, the leachate poses a serious threat to the environment and to public health. In this study, the use of an engineered system consisting of an up-flow anaerobic sludge blanket reactor and a vertical flow subsurface constructed wetland for the treatment of landfill leachate was investigated. The leachate obtained from a landfill facility in Aksaray, Turkey was fed into both systems and laboratory tests showed that, over the 6-week study period, the systems were able to efficiently remove chemical oxygen demand (88.6 %) and total nitrogen (80.7 %). The results of this study suggested that Typha angustifolia significantly increased the removal of total nitrogen. The higher ammonia removal occurred in the anaerobic system and also the removal efficiency increased in planted bed, it is presumed to be the result of the ammonia nitrogen uptake by the roots of the plant.

scholarly journals The comparison of efficiency of Fenton and photo-Fenton treatment of stabilised landfill leachate / Porównanie efektywności oczyszczania odcieków z ustabilizowanego składowiska odpadów komunalnych w procesie Fentona i foto-Fentona

2015 ◽  
Vol 26 (3) ◽  
pp. 49-53 ◽  
Author(s):  
Anna Kwarciak-Kozłowska ◽  
Aleksandra Krzywicka
Keyword(s):  
Landfill Leachate ◽  
Fenton Reaction ◽  
Ferrous Sulphate ◽  
Oxygen Demand ◽  
Ammonia Nitrogen ◽  
Ammonia Removal ◽  
Mass Ratio ◽  
Leachate Treatment ◽  
Initial Ph ◽  
Removal Efficiencies

Abstract The goal of this article was to compare the efficiency of Fenton and photo-Fenton reaction used for stabilised landfill leachate treatment. The mass ratio of COD:H2O2 was fixed to 1:2 for every stages. The dose of reagents (ferrous sulphate/hydrogen peroxide) was different and ranged from 0.1 to 0.5. To determine the efficiency of treatment, the BOD (biochemical oxygen demand COD (chemical oxygen demand), TOC (total organic carbon) , ammonia nitrogen and BOD/COD ratio was measured. The experiment was carried out under the following conditions: temperature was 25ºC, the initial pH was adjusted to 3.0. Every processes were lasting 60 minutes. The most appropriate dose of reagents was 0.25 (Fe2+/H2O2). It was found that the application of UV contributed to increase of COD, TOC and ammonia removal efficiencies by an average of 14%.

A mass balance study on nitrification and deammonification in vertical flow constructed wetlands treating landfill leachate

2007 ◽  
Vol 56 (3) ◽  
pp. 117-123 ◽  
Author(s):  
G. Sun ◽  
D. Austin
Keyword(s):  
Mass Balance ◽  
Total Nitrogen ◽  
Landfill Leachate ◽  
Nitrogen Loss ◽  
Organic Content ◽  
Vertical Flow ◽  
Ammoniacal Nitrogen ◽  
High Concentration ◽  
Balance Study ◽  
Mass Balance Study

A laboratory-scale, mass-balance study was carried out on the transformation of nitrogenous pollutants in four vertical flow wetland columns. Landfill leachate containing low organic matter, but a high concentration of ammoniacal-nitrogen, was treated under dissolved oxygen concentrations close to saturation. Influent total nitrogen (TN) comprised ammoniacal-nitrogen with less than 1% nitrate and nitrite, negligible organic nitrogen, and very low BOD. Nitrification occurred in three of the four columns. There was a substantial loss of total nitrogen (52%) in one column, whereas other columns exhibited zero to minor losses (<12%). Nitrogen loss under study conditions was unexpected. Two hypotheses are proposed to account for it: (1) either the loss of TN is attributed to nitrogen transformation into a form (provisionally termed α-nitrogen) that is undetectable by the analytical methods used; or (2) the loss is caused by microbial denitrification or deammonification. By elimination and stoichiometric mass balance calculations, completely autotrophic nitrogen-removal over nitrite (CANON) deammonification is confirmed as responsible for nitrogen loss in one column. This result reveals that CANON can be native to aerobic engineered wetland systems treating high ammonia, low organic content wastewater.

scholarly journals Comparative Study on Advanced Nitrogen Removal of Landfill Leachate Treated by SBR and SBBR

Water ◽  
2021 ◽  
Vol 13 (22) ◽  
pp. 3240
Author(s):  
Jinfeng Jiang ◽  
Liang Ma ◽  
Lianjie Hao ◽  
Daoji Wu ◽  
Kai Wang
Keyword(s):  
Total Nitrogen ◽  
Nitrogen Removal ◽  
Landfill Leachate ◽  
Batch Reactor ◽  
Nitrogen Concentration ◽  
Carbon Sources ◽  
Oxygen Demand ◽  
Ammonia Nitrogen ◽  
Two Systems ◽  
Advanced Nitrogen Removal

In order to achieve advanced nitrogen removal from landfill leachate without the addition of external carbon sources, a Sequencing Batch Reactor (SBR) and a Sequencing Biofilm Batch Reactor (SBBR) were proposed for the treatment of actual landfill leachate with ammonia nitrogen (NH4+-N) and chemical oxygen demand (COD) concentrations of 1000 ± 100 mg/L and 4000 ± 100 mg/L, respectively. The operating modes of both systems are anaerobic–aerobic–anoxic. After 110 days of start-up and biomass acclimation, the effluent COD and the total nitrogen (TN) of the two systems were 650 ± 50 mg/L and 20 ± 10 mg/L, respectively. The removal rates of COD and total nitrogen could reach around 85% and above 95%, respectively. Therefore, advanced nitrogen removal was implemented in landfill leachate without adding any carbon sources. After the two systems were acclimated, nitrogen removing cycles of SBR and SBBR were 24 h and 20 h, respectively. The nitrogen removing efficiency of SBBR was improved by 16.7% in comparison to SBR. In the typical cycle of the two groups of reactors, the nitrification time of the system was the same, which was 5.5 h, indicating that although the fiber filler occupied part of the reactor space, it had no significant impact on the nitrification performance of the system. At the end of aeration, the internal carbon source content of sludge of SBBR was equivalent to that of the SBR system. However, the total nitrogen concentration of SBBR was only 129 mg/L, which is 33.8% lower than that of SBR at 195 mg/L. The main reason was that biofilm enhanced the simultaneous nitrification and denitrification (SND) effect of the system.

Potential of Recalcitrant Effluent to Generate Biogas by Up-flow Anaerobic Sludge Blanket and Mechanical Vapour Recompression (MVR) -A Case Study

2021 ◽  
Author(s):  
Manoj Wagh ◽  
Pravin Nemade ◽  
Ashok Biradar
Keyword(s):  
Oxygen Demand ◽  
Anaerobic Treatment ◽  
Primary Treatment ◽  
Organic Content ◽  
Cod Removal ◽  
Anaerobic Sludge ◽  
Spent Wash ◽  
Distillery Spent Wash ◽  
Anaerobic Sludge Blanket

Abstract The spent wash generated in the distillation process has very high organic content like biochemical oxygen demand (BOD) and chemical oxygen demand (COD), which are treated to curtail the levels of COD and BOD. Day by day the rules and legislation are stringent and mandatory for disposal of distillery spent wash. Anaerobic treatment is the primary treatment widely adopted to generate biogas. To find out the potential of recalcitrant effluent a case study of the full-scale operating biomethanation plants at Sanjivani, SSK Ltd, Kopargaon, (M.S), India and Spectrum Renewable Energy Pvt. Ltd. (SREL) Warnanagar (M. S.), India was incorporated. Up-flow Anaerobic Sludge Blanket treatment was implemented to generate the biogas. Sanjivani distillery industry, Kopargaon has a COD removal efficiency of 70–72% with specific biogas generation of 0.5 m3/ kg COD removal, and total biogas generated is 38000 Nm3/d. Mechanical Vapour Recompression (MVR) is the cutting-edge technology executed to convert distillery spent wash into useful by-products such as biogas, clean water, and organic manure.

APLIKASI PROSES DIGESTASI ANAEROBIK LUMPUR BIOLOGI INSTALASI PENGOLAHAN AIR LIMBAH INDUSTRI KERTAS

2014 ◽  
Vol 4 (02) ◽  
Author(s):  
Rina S. Soetopo ◽  
Sri Purwati ◽  
Henggar Hardiani ◽  
Mukharomah Nur Aini ◽  
Krisna Adhitya Wardhana
Keyword(s):  
Oxygen Demand ◽  
Total Solid ◽  
Pilot Scale ◽  
Organic Content ◽  
Solid Content ◽  
Uasb Reactor ◽  
Anaerobic Sludge ◽  
Organic Loading ◽  
Total Solid Content ◽  
Average Value

A continuous pilot scale study has been conducted to investigate the effectiveness of anaerobic digestion of biological sludge. The sludge has a total solid content of 0.53% - 1.1%, pH of 7.20 to 7.32. Its organic content is about 97 %, The research were conducted in two stages, which are acidification (performed in 3 m3 the Continously Stirred Tank Reactor/CSTR at pH of 5.5 to 6.0) and methanation (performed in 5 m3 the Up Flow Anaerobic Sludge Blanket/UASB reactor at pH 6.5 to 7.0). The retention time (RT) was gradually shortened from 6 days to 1 day for acidification and from 8 days to 2 days for methanation. The results showed that operating the CSTR at the RT of 1 day and the organic loading of 8.23 g Volatile Solid (VS)/m3.day could produce Volatile Fatty Acid (VFA) at an average value of 17.3 g/kg VS.day. Operating the UASB reactor at the RT of 2 days and the organic loading (Chemical Oxygen Demand/COD) of 2.4 kg COD/m3.day could produce biogas at an average value of 66.3 L/day, with an average methane content of 69.9%, methane rate of 0.17 L CH4/g COD reduction or 19.06 L CH4/kg VS. Furthermore, methanation could reduce COD at an average value of 51.2 %, resulting in the effluent average value of COD filtrate and COD total of 210.1 mg/L and 375.2 mg /L, respectively.Keywords: acidification, methanation, CSTR, UASB, biogas ABSTRAKPercobaan digestasi anaerobik lumpur IPAL biologi industri kertas secara kontinyu skala pilot telah dilakukan di industri kertas dengan tujuan mengkaji efektivitas proses digestasi anaerobik dalam mengolah lumpur tersebut. Lumpur yang digunakan memiliki total solids sekitar 0,53% – 1,1%, pH netral (7,20 – 7,32) dengan komponen utama senyawa organik sekitar 97%. Percobaan dilakukan dalam dua tahap yaitu asidifikasi dalam reaktor CSTR berkapasitas 3 m3 pada pH 5,5 – 6,0 dan metanasi dalam reaktor UASB berkapasitas 5 m3 pada pH 6,5 – 7,0. Percobaan dilakukan dengan waktu retensi yang dipersingkat secara bertahap dari 6 hari ke 1 hari untuk proses asidifikasi dan dari 8 hari ke 2 hari untuk proses metanasi. Hasil percobaan menunjukkan bahwa pengoperasian reaktor CSTR dengan waktu retensi 1 hari dan beban organik 8,3 g VS/m3.hari dapat menghasilkan VFA rata-rata 17,3 g/kg VS.hari dengan kisaran 8,36 – 30,59 g/kg VS.hari, sedangkan pengoperasian reaktor UASB pada waktu retensi 2 hari dan beban organik 2,4 kg COD/m3.hari dapat menghasilkan biogas rata-rata 66,3 L/hari dengan kadar metana rata-rata 69,9% atau 0,17 L CH4/g COD reduksi atau 19,06 L CH4/kg VS. Selain itu proses metanasi dapat menurunkan COD terlarut rata-rata 51,2%, dengan konsentrasi efluen COD terlarut  rata-rata 210,1 mg/L dan COD total rata-rata 375,2 mg/L.Kata kunci: asidifikasi, metanasi, CSTR, UASB, biogas

scholarly journals Digestate Liquid Fraction Treatment with Filters Filled with Recovery Materials

Water ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 21
Author(s):  
Ilaria Piccoli ◽  
Giuseppe Virga ◽  
Carmelo Maucieri ◽  
Maurizio Borin
Keyword(s):  
Chemical Oxygen Demand ◽  
Total Nitrogen ◽  
Liquid Fraction ◽  
Oxygen Demand ◽  
Ammonia Nitrogen ◽  
Green Technology ◽  
Filling Material ◽  
Community Interactions ◽  
Material Particle ◽  
N Removal

Constructed wetlands (CWs) represent a green technology for digestate liquid fraction (DLF) treatment. However, previous research has warned about their performance when treating wastewater with high suspended solid and organic loads. In addition, the high NH4-N concentration typical of this wastewater can compromise vegetation establishment and activity. In view of this, a digestate pretreatment is needed. This study aimed to test the performance of filters filled with recovery materials, such as brick and refractory material, for DLF pretreatment. The effect on DLF physical (electrical conductivity, pH, dissolved oxygen, and temperature) and chemical (total nitrogen, ammonia–nitrogen, nitrate–nitrogen, total phosphorus, soluble phosphorus, and chemical oxygen demand) characteristics was monitored during eight weekly cycles. The effect of filtration on total nitrogen and ammonia–nitrogen removal began after about one month of loading, suggesting that an activation period is necessary for bacteria. For effective N removal, the presence of multiple digestate recirculations per day through the filters appears mandatory to guarantee the alternation of nitrification and denitrification conditions. For P removal, filling material particle size appeared to be more important than its composition. Unclear performances were observed considering chemical oxygen demand. Further studies on filling media and microbial community interactions, and the long-term efficiency of filters, are desirable.

Improved nitrogen removal in upflow anaerobic sludge blanket (UASB) reactors by incorporation of Anammox bacteria into the granular sludge

2004 ◽  
Vol 49 (11-12) ◽  
pp. 69-76 ◽  
Author(s):  
J.E. Schmidt ◽  
D.J. Batstone ◽  
I. Angelidaki
Keyword(s):  
In Situ Hybridisation ◽  
Granular Sludge ◽  
Ammonia Removal ◽  
Appropriate Technology ◽  
Upflow Anaerobic Sludge Blanket ◽  
Anaerobic Sludge ◽  
The Third ◽  
Anammox Activity ◽  
Anaerobic Sludge Blanket ◽  
Uasb Reactors

Upflow anaerobic sludge blanket reactors may offer a number of advantages over conventional mixed-tank, SBR, and biofilm reactors, including high space-loading, low footprint, and resistance to shocks and toxins. In this study, we assessed the use of upflow anaerobic sludge blanket (UASB) reactor technology as applied to anaerobic ammonia removal, or Anammox. Four 200 ml UASB reactors were inoculated with 50% (by volume) anaerobic granular sludge and 50% flocular sludge from different sources (all with the potential for containing Anammox organisms). Tools used to assess the reactors included basic analyses, fluorescent in-situ hybridisation, and mathematical modelling, with statistical non-linear parameter estimation. Two of the reactors showed statistically identical Anammox activity (i.e., identical kinetic parameters), with good ammonia and nitrite removal (0.14 kgNHx m-3 reactor day-1, with 99% ammonia removal). The third reactor also demonstrated significant Anammox activity, but with poor identifiability of parameters. The fourth reactor had no statistical Anammox activity. Modelling indicated that poor identifiability and performance in the third and fourth reactors were related to an excess of reduced carbon, probably originating in the inoculum. Accumulation of Anammox organisms was confirmed both by a volume loading much lower than the growth rate, and response to a probe specific for organisms previously reported to mediate Anammox processes. Overall, the UASB reactors were effective as Anammox systems, and identifiability of the systems was good, and repeatable (even compared to a previous study in a rotating biological contactor). This indicates that operation, design, and analysis of Anammox UASB reactors specifically, and Anammox systems in general, are reliable and portable, and that UASB systems are an appropriate technology for this process.

scholarly journals Effects of selection and compiling strategy of substrates in column-type vertical-flow constructed wetlands on the treatment of synthetic landfill leachate containing bisphenol A

2021 ◽  
Author(s):  
Rajani Ghaju Shrestha ◽  
Daisuke Inoue ◽  
Michihiko Ike
Keyword(s):  
Activated Carbon ◽  
Bisphenol A ◽  
Landfill Leachate ◽  
Low Cost ◽  
Oxygen Demand ◽  
Ammonium Nitrogen ◽  
Pollutant Removal ◽  
Vertical Flow ◽  
Batch Mode ◽  
Synthetic Leachate

Abstract A constructed wetland (CW) is a low-cost, eco-friendly, easy-to-maintain, and widely applicable technology for treating various pollutants in the waste landfill leachate. This study determined the effects of the selection and compiling strategy of substrates used in CWs on the treatment performance of a synthetic leachate containing bisphenol A (BPA) as a representative recalcitrant pollutant. We operated five types of lab-scale vertical-flow CWs using only gravel (CW1), a sandwich of gravel with activated carbon (CW2) or brick crumbs (CW3), and two-stage hybrid CWs using gravel in one column and activated carbon (CW4) or brick crumbs (CW5) in another to treat synthetic leachate containing BPA in a 7-d sequential batch mode for 5 weeks. CWs using activated carbon (CW2 and CW4) effectively removed ammonium nitrogen (NH4-N) (99–100%), chemical oxygen demand (COD) (93–100%), and BPA (100%), indicating that the high adsorption capacity of activated carbon was the main mechanism involved in their removal. CW5 also exhibited higher pollutant removal efficiencies (NH4-N: 94–99%, COD: 89–98%, BPA: 89–100%) than single-column CWs (CW1 and CW3) (NH4-N: 76–100%, COD: 84–100%, BPA: 51–100%). This indicates the importance of the compiling strategy along with the selection of an appropriate substrate to improve the pollutant removal capability of CWs.

scholarly journals The Concept of Wastes to Energy Using Sugary Wastes

2012 ◽  
Vol 9 ◽  
pp. 57-62
Author(s):  
Fiza Sarwar ◽  
Wajeeha Malik ◽  
Muhammad Salman Ahmed ◽  
Harja Shahid
Keyword(s):  
Volatile Fatty Acids ◽  
Loading Rate ◽  
Biogas Production ◽  
Oxygen Demand ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
Loading Rates ◽  
Sugar Mills ◽  
Anaerobic Sludge Blanket

Abstract: This study was designed using actual effluent from the sugary mills in an Up-flow Anaerobic Sludge Blanket (UASB) Reactor to evaluate treatability performance. The reactor was started-up in step-wise loading rates beginning from 0.05kg carbon oxygen demand (COD)/m3-day to 3.50kg-COD/m3-day. The hydraulic retention time (HRT) was slowly decreased from 96 hrs to eight hrs. It was observed that the removal efficiency of COD of more than 73% can be easily achieved at an HRT of more than 16 hours corresponding to an average organic loading rate (OLR) of 3.0kg-COD/m3-day, at neutral pH and constant temperature of 29°C. The average VFAs (volatile fatty acids) and biogas production was observed as 560mg/L and 1.6L/g-CODrem-d, respectively. The average methane composition was estimated as 62%. The results of this study suggest that the treatment of sugar mills effluent with the anaerobic technology seems to be more reliable, effective and economical.DOI: http://dx.doi.org/10.3126/hn.v9i0.7075 Hydro Nepal Vol.9 July 2011 57-62

scholarly journals Assessment of High Salinity Wastewater Treatment with Dewatered Alum Sludge-Aerobic Membrane Reactor

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Wei Kang ◽  
Xiyu Cui ◽  
Yanrui Cui ◽  
Linlin Bao ◽  
Kaili Ma
Keyword(s):  
Membrane Reactor ◽  
High Salinity ◽  
Oxygen Demand ◽  
Ammonia Nitrogen ◽  
Organic Content ◽  
Organic Loading Rate ◽  
Soluble Phosphate ◽  
Aquatic Life ◽  
Alum Sludge ◽  
Salinity Wastewater

Abstract The discharge of wastewater containing both high salinity and high organic content without prior treatment is detrimental to aquatic life and water hygiene. In order to integrate the advantages of membrane treatment and biological treatment, and exert the phosphorus removal efficiency of dewatered alum sludge, in this study, an aerobic membrane reactor based on dehydrated alum sludge was used to treat mustard tuber wastewater with salinity of 6.8-7.3 % under the conditions of 30 °C, 20 kPa trans-membrane pressure (TMP) and chemical oxygen demand (COD) of 3300-3900 mg/L. Three replicate reactors were applied to assess the operational performance under different organic loading rate (OLR). The results showed that all reactors were effective in removing COD, ammonia nitrogen (NH4 +-N) and soluble phosphate (SP) under the conditions of 30 °C and 20 kPa of TMP. Meanwhile, the effluent concentration of COD, NH4 +-N and SP all increased while OLR was changed from 1.0 to 3.0 kg COD/m3/day, and the effluent COD and NH4 +-N concentration except for SP could reach the B-level of Chinese “Wastewater quality standards for discharge to municipal sewers” when OLR was less than 3.0 kg COD/m3/day. This indicates that dewatered alum sludge-based aerobic membrane reactor is a promising bio-measure for treating high salinity wastewater.

Sign in / Sign up

Export Citation Format

Share Document