scholarly journals Preliminary Results of the Temperature Distribution Measurements Around the Vertical Ground Heat Exchangers Tubes

2020 ◽  
Vol 27 (4) ◽  
pp. 509-528
Author(s):  
Joanna Piotrowska-Woroniak
Keyword(s):  
Temperature Distribution ◽  
Heat Pump ◽  
Cooling Capacity ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Water Type ◽  
Preliminary Results ◽  
Ground Heat Exchangers ◽  
Vertical Ground ◽  
The Way

Abstract The paper presents the preliminary results of the temperature distribution to a depth of 100 m in the two selected vertical geothermal wells during operation of the heat pump and ground temperature measurement without vertical ground probes work. Research was carried out from the third decade of December to the end of February. The wells are the lower energy source for two heat pumps brine/water type with heating power of 117.2 kW each and 95.9 kW cooling capacity installed in the building of The Faculty of Civil and Environmental Engineering, Bialystok University of Technology in Bialystok. With heat pumps work 52 vertical ground probes to a depth of 100 m each. The article presents the way of making probes equipped with 30 digital temperature sensors to record the temperature distribution in the vertical probes and in the ground and it shows the way of making the test bench using the groundwater wells with vertical probes. The average coefficient of performance COP of the heat pump HP in the months of January and February has been designated.

scholarly journals The energy source for heat pumps with vertical heat exchangers

2018 ◽  
Vol 44 ◽  
pp. 00157
Author(s):  
Piotr Rynkowski
Keyword(s):  
Heat Pump ◽  
Heat Exchangers ◽  
Electricity Consumption ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Temperature Analysis ◽  
Heat Flows ◽  
Ground Heat Exchangers ◽  
Vertical Heat ◽  
Vertical Ground

The paper presents the ground temperature analysis, heat flows and energy transferred from the soil massif by the vertical ground heat exchangers (VGHE). Three cases – with one, two and three vertical heat exchangers were compared. Their influences on the soil massif temperature in the heat exchangers area were shown. The mass flow and the temperature at the inlet and outlet side of the heat pump were measured in each circuit. Additional, the electricity consumption by the heat pump and energy supply to buffer vessel were measured. Finally, the Coefficient of Performance (COP) as a function of length of VGHE is shown for selected interval time.

scholarly journals Investigation of the Environmentally-Friendly Refrigerant R152a for Air Conditioning Purposes

2018 ◽  
Vol 9 (1) ◽  
pp. 119 ◽  
Author(s):  
Evangelos Bellos ◽  
Christos Tzivanidis
Keyword(s):  
Heat Pump ◽  
High Performance ◽  
Environmentally Friendly ◽  
Cooling Capacity ◽  
Heat Pumps ◽  
Operating Conditions ◽  
Coefficient Of Performance ◽  
Cooling Systems ◽  
Detailed Model ◽  
Ambient Temperatures

Heat pumps are efficient and well-established technologies for providing the proper cooling load in the building sector. The objective of this work is the parametric investigation of a heat pump operating with the promising refrigerant R152a for different operating conditions. More specifically, the heat pump is studied for different ambient temperatures, different indoor temperatures and various compressor rotational speeds. The cooling capacity and the coefficient of performance (COP) are the most important parameters which calculated in every scenario. A detailed model is developed in Engineering Equations Solver (EES) and it is validated with literature data. According to the final results, the system can operate in nominal conditions with 5 kW cooling capacity and a COP equal to 6.46. It is found that the COP can be ranged from 4 to 12 and the cooling capacity, while the cooling capacity can reach up to 9 kW. Moreover, a regression equation about the performance of the system is suggested. The obtained results indicate that the use of the R152a leads to high performance and so it can be an environmentally friendly choice for the cooling systems.

scholarly journals Heat Pump Bridge Analysis Using the Modified Energy Transfer Diagram

Energies ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 137
Author(s):  
Florian Schlosser ◽  
Heinrich Wiebe ◽  
Timothy G. Walmsley ◽  
Martin J. Atkins ◽  
Michael R. W. Walmsley ◽  
...  
Keyword(s):  
Energy Transfer ◽  
Heat Pump ◽  
Heat Recovery ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Combined Application ◽  
Recovery Potential ◽  
Composite Curve ◽  
And Performance ◽  
The Individual

Heat pumps are the key technology to decarbonise thermal processes by upgrading industrial surplus heat using renewable electricity. Existing insight-based integration methods refer to the idealised Grand Composite Curve requiring the full exploitation of heat recovery potential but leave the question of how to deal with technical or economic limitations unanswered. In this work, a novel Heat Pump Bridge Analysis (HPBA) is introduced for practically targeting technical and economic heat pump potential by applying Coefficient of Performance curves into the Modified Energy Transfer Diagram (METD). Removing cross-Pinch violations and operating heat exchangers at minimum approach temperatures by combined application of Bridge Analysis increases the heat recovery rate and reduce the temperature lift to be pumped at the same time. The insight-based METD allows the individual matching of heat surpluses and deficits of individual streams with the capabilities and performance of different market-available heat pump concepts. For an illustrative example, the presented modifications based on HPBA increase the economically viable share of the technical heat pump potential from 61% to 79%.

scholarly journals Factors Shaping A/W Heat Pumps CO₂ Emissions—Evidence from Poland

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1576
Author(s):  
Piotr Jadwiszczak ◽  
Jakub Jurasz ◽  
Bartosz Kaźmierczak ◽  
Elżbieta Niemierka ◽  
Wandong Zheng
Keyword(s):  
Air Quality ◽  
Power System ◽  
Heat Pump ◽  
Heat Pumps ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Conventional Heating ◽  
Additional Stress ◽  
The European Union ◽  
Energy Mix

Heating and cooling sectors contribute to approximately 50% of energy consumption in the European Union. Considering the fact that heating is mostly based on fossil fuels, it is then evident that its decarbonization is one of the crucial tasks for achieving climate change prevention goals. At the same time, electricity sectors across the globe are undergoing a rapid transformation in order to accommodate the growing capacities of non-dispatchable solar and wind generators. One of the proposed solutions to achieve heating sector decarbonization and non-dispatchable generators power system integration is sector coupling, where heat pumps are perceived as a perfect fit. Air source heat pumps enable a rapid improvement in local air quality by replacing conventional heating sources, but at the same time, they put additional stress on the power system. The emissions associated with heat pump operation are a combination of power system energy mix, weather conditions and heat pump technology. Taking the above into consideration, this paper presents an approach to estimate which of the mentioned factors has the highest impact on heat pump emissions. Due to low air quality during the heating season, undergoing a power system transformation (with a relatively low share of renewables) in a case study located in Poland is considered. The results of the conducted analysis revealed that for a scenario where an air-to-water (A/W) heat pump is supposed to cover space and domestic hot water load, its CO2 emissions are shaped by country-specific energy mix (55.2%), heat pump technology (coefficient of performance) (33.9%) and, to a lesser extent, by changing climate (10.9%). The outcome of this paper can be used by policy makers in designing decarbonization strategies and funding distribution.

scholarly journals Heat pump systems: A mini review

2021 ◽  
Vol 4 (2) ◽  
pp. 73-81
Author(s):  
Mohammad Omar Temori ◽  
František Vranay
Keyword(s):  
Heat Pump ◽  
Electricity Consumption ◽  
Cost Savings ◽  
Electrical Energy ◽  
Primary Energy ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Heating And Cooling ◽  
Ground Source ◽  
Reduce Electricity Consumption

In this work, a mini review of heat pumps is presented. The work is intended to introduce a technology that can be used to income energy from the natural environment and thus reduce electricity consumption for heating and cooling. A heat pump is a mechanical device that transfers heat from one environmental compartment to another, typically against a temperature gradient (i.e. from cool to hot). In order to do this, an energy input is required: this may be mechanical, electrical or thermal energy. In most modern heat pumps, electrical energy powers a compressor, which drives a compression - expansion cycle of refrigerant fluid between two heat exchanges: a cold evaporator and a warm condenser. The efficiency or coefficient of performance (COP), of a heat pump is defined as the thermal output divided by the primary energy (electricity) input. The COP decreases as the temperature difference between the cool heat source and the warm heat sink increases. An efficient ground source heat pump (GSHP) may achieve a COP of around 4. Heat pumps are ideal for exploiting low-temperature environmental heat sources: the air, surface waters or the ground. They can deliver significant environmental (CO2) and cost savings.

scholarly journals Critical Analysis of Process Integration Options for Joule-Cycle and Conventional Heat Pumps

Energies ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 635 ◽  
Author(s):  
Limei Gai ◽  
Petar Sabev Varbanov ◽  
Timothy Gordon Walmsley ◽  
Jiří Jaromír Klemeš
Keyword(s):  
Heat Pump ◽  
Process Integration ◽  
Waste Heat ◽  
Correct Choice ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Large Temperature ◽  
Temperature Changes ◽  
Application Range ◽  
Source And Sink

To date, research on heat pumps (HP) has mainly focused on vapour compression heat pumps (VCHP), transcritical heat pumps (TCHP), absorption heat pumps, and their heat integration with processes. Few studies have considered the Joule cycle heat pump (JCHP), which raises several questions. What are the characteristics and specifics of these different heat pumps? How are they different when they integrate with the processes? For different processes, which heat pump is more appropriate? To address these questions, the performance and integration of different types of heat pumps with various processes have been studied through Pinch Methodology. The results show that different heat pumps have their own optimal application range. The new JCHP is suitable for processes in which the temperature changes of source and sink are both massive. The VCHP is more suitable for the source and sink temperatures, which are near-constant. The TCHP is more suitable for sources with small temperature changes and sinks with large temperature changes. This study develops an approach that provides guidance for the selection of heat pumps by applying Process Integration to various combinations of heat pump types and processes. It is shown that the correct choice of heat pump type for each application is of utmost importance, as the Coefficient of Performance can be improved by up to an order of magnitude. By recovering and upgrading process waste heat, heat pumps can save 15–78% of the hot utility depending on the specific process.

scholarly journals A Study on the Performance of a Cascade Heat Pump for Generating Hot Water

Energies ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 4313 ◽  
Author(s):  
Boahen ◽  
Choi
Keyword(s):  
Heat Exchanger ◽  
Energy Saving ◽  
Heat Pump ◽  
Heat Pumps ◽  
Hot Water ◽  
Research Interest ◽  
Coefficient Of Performance ◽  
Energy Saving Potential ◽  
Heating Capacity

The use of cascade heat pumps for hot water generation has gained much attention in recent times. The big question that has attracted much research interest is how to enhance the performance and energy saving potential of these cascade heat pumps. This study therefore proposed a new cycle to enhance performance of the cascade heat pump by adopting an auxiliary heat exchanger (AHX) in desuperheater, heater and parallel positions at the low stage (LS) side. The new cascade cycle with AHX in desuperheater position was found to have better performance than that with AHX at heater and parallel positions. Compared to the conventional cycle, heating capacity and coefficient of performance (COP) of the new cascade cycle with AHX in desuperheater position increased up to 7.4% and 14.9% respectively.

scholarly journals Installation and Operation of a Solar Cooling and Heating System Incorporated with Air-Source Heat Pumps

Energies ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 996 ◽  
Author(s):  
Li Huang ◽  
Rongyue Zheng ◽  
Udo Piontek
Keyword(s):  
Heating System ◽  
Cooling Capacity ◽  
Heat Pumps ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Energy Yield ◽  
Absorption Chiller ◽  
Annual Average ◽  
Water Storage Tank ◽  
Solar Cooling

A solar cooling and heating system incorporated with two air-source heat pumps was installed in Ningbo City, China and has been operating since 2018. It is composed of 40 evacuated tube modules with a total aperture area of 120 m2, a single-stage and LiBr–water-based absorption chiller with a cooling capacity of 35 kW, a cooling tower, a hot water storage tank, a buffer tank, and two air-source heat pumps, each with a rated cooling capacity of 23.8 kW and heating capacity of 33 kW as the auxiliary system. This paper presents the operational results and performance evaluation of the system during the summer cooling and winter heatingperiod, as well as on a typical summer day in 2018. It was found that the collector field yield and cooling energy yield increased by more than 40% when the solar cooling and heating system is incorporated with heat pumps. The annual average collector efficiency was 44% for cooling and 42% for heating, and the average coefficient of performance (COP) of the absorption chiller ranged between 0.68 and 0.76. The annual average solar fraction reached 56.6% for cooling and 62.5% for heating respectively. The yearly electricity savings accounted for 41.1% of the total electricity consumption for building cooling and heating.

Performance of Heat Pump Water Heater (HPWH) Systems and Their Impacts on Electric Utility Loads

2010 ◽  
Vol 2 (2) ◽  
Author(s):  
Yahya I. Sharaf-Eldeen
Keyword(s):  
Heat Pump ◽  
Energy Savings ◽  
Electric Energy ◽  
Cost Savings ◽  
Electric Heating ◽  
Electric Utility ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Water Heaters ◽  
Peak Loads

This work involves measurements, analyses, and evaluation of performance of air-source heat pump water heaters (HPWHs), and their impacts on electric utility loads. Two add-on, heat pumps (HPs) rated at 7000 BTU/h (2.051 kW) and 12,000 BTU/h (3.517 kW) were utilized. The HPs were retrofitted to two 50 gal (189.3 l) electric water heaters (EWHs) with their electric heating elements removed. A third standard EWH was used for comparison. The testing setups were fully instrumented for measurements of all pertinent parameters, including inlet and outlet water temperatures, inlet and outlet air temperatures of the HPs, temperature and humidity of the surrounding air, volume of water drawn out of the storage tanks, as well as the electric energy consumptions of the systems. Performance measures evaluated included the coefficient of performance, the energy factor (EF), and the first hour rating (FHR). The HPWH systems gave EFs ranging from 1.8 to 2.5 and corresponding energy savings (and reductions in utility peak loads) ranging from 49.0% to 63.0%, approximately. The values obtained in the summer months were, as expected, somewhat higher than those obtained in the winter ones. The average values of the EFs and energy savings (and reductions in utility peak loads) were about 2.1 and 56.0%, respectively. FHR results were much lower for the HPWHs compared with those for the standard EWH. These results show that HPWHs are much more efficient compared with standard EWHs. While the average value of the EF for the EWH was about 0.92, the HPWHs yielded EFs averaging more than 2.00, resulting in annual energy savings averaging more than 50%. The results also show that HPWHs are effective at reducing utility peak loads, in addition to providing substantial cost savings to consumers.

Sign in / Sign up

Export Citation Format

Share Document