scholarly journals Study on Adsorption of Nickel and Methylene Blue in Aqueous Solution by Magnetic Carboxylate-Rich Carbon

2021 ◽  
Vol 37 (2) ◽  
Author(s):  
Doan Van Dat ◽  
Nguyen Hoai Thuong ◽  
Tran Thi Kieu Ngan ◽  
Le Thi Thanh Nhi ◽  
Dao My Uyen ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Adsorption Capacity ◽  
Ph Value ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
High Adsorption ◽  
Endothermic Process ◽  
High Adsorption Capacity

In this study, magnetic carboxylate-rich carbon material (Fe3O4@CRC) was synthesized via a low-temperature carbonization method and applied as an adsorbent for adsorption of Ni(II) ions and methylene blue (MB) in aqueous solution. The synthesized Fe3O4@CRC was characterized by various techniques (XRD, FTIR, FE-SEM, TEM, EDX, VSM, and BET). The adsorption kinetics, isotherms, thermodynamics, and the effects of key adsorption factors, including the pH value, initial adsorbate concentration, contact time, adsorbent dose and temperature were investigated in detail. The results showed that Fe3O4@CRC exhibited a high adsorption capacity for MB and Ni(II) with the maximum adsorption capacity of 187.26 mg/g and 106.75 mg/g, respectively. The adsorption of MB and Ni(II) on Fe3O4@CRC was a spontaneous and endothermic process, and was best described with the first-order kinetic model, Freundlich (for MB) and Langmuir (for Ni(II)) isotherm models. In addition, Fe3O4@CRC could maintain a high adsorption capacity after many consecutive cycles. Therefore, the Fe3O4@CRC material can be used as a highly efficient adsorbent for the removal of heavy metals and dyes from wastewater due to the advantages of high adsorption performance, easy separation, and good reusability.  

Carbonized medlar-core particles as a new biosorbent for removal of Cu2+ from aqueous solution and study of its surface morphology

2016 ◽  
Vol 74 (1) ◽  
pp. 236-245 ◽  
Author(s):  
Narges Samadani Langeroodi ◽  
Elaheh Safaei
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
High Adsorption ◽  
Langmuir Adsorption ◽  
Adsorption Isotherm Models ◽  
Freundlich Adsorption Isotherm ◽  
High Adsorption Capacity ◽  
Core Particles

The objective of this study was to investigate the use of carbonized medlar-core particles as a new biosorbent to remove Cu2+ from aqueous solution. Fourier transform infrared spectroscopy and scanning electron microscopy were used to characterize the biosorbent. This paper reports the effects of adsorbent dose, pH, temperature and concentration of adsorbate. Batch isotherm studies were also performed to understand the ability of the adsorbent. The adsorption behavior of the Cu2+ was studied using Langmuir and Freundlich adsorption isotherm models. The maximum adsorption capacity determined from the Langmuir adsorption equation has been found as 43.478 mg.g−1 at 298.15 K. The adsorption of Cu2+ by medlar core in carbonized form was spontaneous and endothermic. It was also found that the biosorption of Cu2+ followed second-order kinetics. Carbonized medlar-core particles showed great potential in aqueous solution due to the high adsorption capacity.

Parametric and adsorption kinetic studies of methylene blue removal from simulated textile water using durian (Durio zibethinus murray) skin

2015 ◽  
Vol 72 (6) ◽  
pp. 896-907 ◽  
Author(s):  
S. M. Anisuzzaman ◽  
Collin G. Joseph ◽  
D. Krishnaiah ◽  
A. Bono ◽  
L. C. Ooi
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Dye Adsorption ◽  
Freundlich Isotherm ◽  
Kinetic Studies ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Durio Zibethinus

In this study, durian (Durio zibethinus Murray) skin was examined for its ability to remove methylene blue (MB) dye from simulated textile wastewater. Adsorption equilibrium and kinetics of MB removal from aqueous solutions at different parametric conditions such as different initial concentrations (2–10 mg/L), biosorbent dosages (0.3–0.7 g) and pH solution (4–9) onto durian skin were studied using batch adsorption. The amount of MB adsorbed increased from 3.45 to 17.31 mg/g with the increase in initial concentration of MB dye; whereas biosorbent dosage increased from 1.08 to 2.47 mg/g. Maximum dye adsorption capacity of the durian skin was found to increase from 3.78 to 6.40 mg/g, with increasing solution pH. Equilibrium isotherm data were analyzed according to Langmuir and Freundlich isotherm models. The sorption equilibrium was best described by the Freundlich isotherm model with maximum adsorption capacity of 7.23 mg/g and this was due to the heterogeneous nature of the durian skin surface. Kinetic studies indicated that the sorption of MB dye tended to follow the pseudo second-order kinetic model with promising correlation of 0.9836 < R2 < 0.9918.

scholarly journals Super-Adsorbent Hydrogels for Removal of Methylene Blue from Aqueous Solution: Dye Adsorption Isotherms, Kinetics, and Thermodynamic Properties

Macromol ◽  
2021 ◽  
Vol 1 (4) ◽  
pp. 256-275
Author(s):  
Buddhabhushan Salunkhe ◽  
Thomas P. Schuman
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Organic Dyes ◽  
Polymer Network ◽  
Dye Adsorption ◽  
Isotherm Models ◽  
High Adsorption ◽  
High Adsorption Capacity ◽  
Efficient Option ◽  
Sodium Styrenesulfonate

Removal of dyes through adsorption from wastewater has gained substantial interest in recent years, especially in development of hydrogel based adsorbents, owing to their easy use and economical nature. The aim of the present study was to design a super-adsorbent hydrogel based on sodium styrenesulfonate (NaSS) monomer for removal of dyes like methylene blue (MB). NaSS displays both an aromatic ring and strongly ionic group in its monomer structure that can enhance adsorption capacity. Poly(sodium styrenesulfonate-co-dimethylacrylamide) hydrogels were prepared by solution free radical polymerization using gelatin methacryloyl (GelMA) as crosslinker, creating a highly porous, three-dimensionally crosslinked polymer network contributing to higher swelling ratios of up to 27,500%. These super-adsorbent hydrogels exhibited high adsorption capacity of 1270 mg/g for MB adsorption with above 98% removal efficiency. This is the first report for such a high adsorption capacity for dye absorbance for NaSS-based hydrogels. Additionally, the adsorption kinetics using a pseudo-first-order and the Freundlich adsorption isotherm models for multilayer, heterogeneous adsorption processes has been reported. The adsorbents’ reusability was confirmed through 4 repeated cycles of desorption-adsorption. The results discussed herein illustrate that NaSS based chemistries can be used as an efficient option for removal of organic dyes from contaminated wastewater.

Adsorption of Phosphate onto Slag from Aqueous Solution

2012 ◽  
Vol 550-553 ◽  
pp. 2255-2258
Author(s):  
Bing Bing Liu ◽  
Hua Yong Zhang ◽  
Lu Yi Zhang
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Adsorption Process ◽  
Freundlich Isotherm ◽  
Langmuir Model ◽  
Phosphate Adsorption ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
High Adsorption ◽  
Pseudo Second Order

Phosphate adsorption from aqueous solution using slag was investigated as the function of pH, contact time and adsorbent dosage. The results showed that the optimum value of pH was 2. Both Langmuir isotherm and Freundlich isotherm model were fit to describe the phosphate adsorption, and the maximum adsorption capacity from Langmuir model calculated was 9.09 mg/L. The adsorption process on slag followed pseudo second-order kinetic. Due to the relatively high adsorption capacity, the slag has the potential for application to removal phosphate from wastewater.

Adsorption Characteristics of Phenol in Aqueous Solution by Pinus massoniana Biochar

2013 ◽  
Vol 295-298 ◽  
pp. 1154-1160 ◽  
Author(s):  
Guo Zhi Deng ◽  
Xue Yuan Wang ◽  
Xian Yang Shi ◽  
Qian Qian Hong
Keyword(s):  
Aqueous Solution ◽  
Ph Value ◽  
Pinus Massoniana ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Adsorbent Dosage ◽  
Salt Ions ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order

The objective of this paper is to investigate the feasibility of phenol adsorption from aqueous solution by Pinus massoniana biochar. Adsorption conditions, including contact time, initial phenol concentration, adsorbent dosage, strength of salt ions and pH, have been investigated by batch experiments. Equilibrium can be reached in 24 h for phenol from 50 to 250 mg• L-1. The optimum pH value for this kind of biochar is 5.0. The amount of phenol adsorbed per unit decreases with the increase in adsorbent dosage. The existence of salt ions makes negligible influence on the equilibrium adsorption capacity. The experimental data is analyzed by the Freundlich and Langmuir isotherm models. Equilibrium data fits well to the Freundlich model. Adsorption kinetics models are deduced and the pseudo-second-order kinetic model provides a good correlation for the adsorbent process. The results show that the Pinus massoniana biochar can be utilized as an effective adsorption material for the removal of phenol from aqueous solution.

scholarly journals Study on the adsorption of methylene blue from aqueous solution using hydrogel glucomannan/graphene oxide

2021 ◽  
Vol 10 (1) ◽  
pp. 59-66
Author(s):  
Son Le Lam ◽  
Phu Nguyen Vinh ◽  
Hieu Le Trung ◽  
Tan Le Thua ◽  
Nhan Dang Thi Thanh ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Graphene Oxide ◽  
Adsorption Capacity ◽  
Organic Dyes ◽  
Dye Adsorption ◽  
Order Kinetic ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Glucomannan/graphene oxide (GM/GO) hydrogel was synthesized by using calcium hydroxide as the crosslinker. The synthesized material was characterized by using IR, XRD, SEM, EDX and RAMAN technology. The composite hydrogel was used for removal of organic dyes from aqueous solution. The results showed that the GM/GO hydrogel had a porous structure and a high adsorption capacity toward methylene blue (MB). The pseudo-second-order kinetic model could fit the rate equation of MB adsorption onto the GM/GO hydrogel. The adsorption of MB onto GM/GO hydrogel was a spontaneous process. In addition, the equilibrium adsorption isotherm data indicated that equilibrium data were fitted to the Langmuir isotherm and the maximum dye adsorption capacity was 198,69 mg.g-1. Moreover, the hydrogel was stable and easily recovered and adsorption capacity was around 97% of the initial saturation adsorption capacity after being used five times.

scholarly journals Modified/Unmodified Nanoparticle Adsorbents of Cellulose Origin With High Adsorptive Potential for Removal of Pb(II) From Aqueous Solution

2017 ◽  
Vol 13 (27) ◽  
pp. 425
Author(s):  
Azeh Yakubu ◽  
Gabriel Ademola Olatunji ◽  
Folahan Amoo Adekola
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Adsorption Process ◽  
Correlation Coefficients ◽  
Solution Temperature ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Kinetics Of Adsorption ◽  
Kinetics Of

This investigation was conducted to evaluate the adsorption capacity of nanoparticles of cellulose origin. Nanoparticles were synthesized by acid hydrolysis of microcrystalline cellulose/cellulose acetate using 64% H3PO4 and characterized using FTIR, XRD, TGA-DTGA, BET and SEM analysis. Adsorption kinetics of Pb (II) ions in aqueous solution was investigated and the effect of initial concentration, pH, time, adsorbent dosage and solution temperature. The results showed that adsorption increased with increasing concentration with removal efficiencies of 60% and 92.99% for Azeh2 and Azeh10 respectively for initial lead concentration of 3 mg/g. The effects of contact time showed that adsorption maximum was attained within 24h of contact time. The maximum adsorption capacity and removal efficiency were achieved at pH6. Small dose of adsorbent had better performance. The kinetics of adsorption was best described by the pseudo-second-Order model while the adsorption mechanism was chemisorption and pore diffusion based on intra-particle diffusion model. The isotherm model was Freundlich. Though, all tested isotherm models relatively showed good correlation coefficients ranging from 0.969-1.000. The adsorption process was exothermic for Azeh-TDI, with a negative value of -12.812 X 103 KJ/mol. This indicates that the adsorption process for Pb by Azeh-TDI was spontaneous. Adsorption by Azeh2 was endothermic in nature.

scholarly journals Adsorption of Mn2+ from Aqueous Solution Using Manganese Oxide-Coated Hollow Polymethylmethacrylate Microspheres (MHPM)

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Dhiraj Dutta ◽  
Jyoti Prasad Borah ◽  
Amrit Puzari
Keyword(s):  
Aqueous Solution ◽  
Manganese Oxide ◽  
Adsorption Capacity ◽  
High Surface ◽  
High Surface Area ◽  
Freundlich Isotherm ◽  
Ion Concentration ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Coated Sand

Results of investigation on adsorption of Mn2+ from aqueous solution by manganese oxide-coated hollow polymethylmethacrylate microspheres (MHPM) are reported here. This is the first report on Mn-coated hollow polymer as a substitute for widely used materials like green sand or MN-coated sand. Hollow polymethylmethacrylate (HPM) was prepared by using a literature procedure. Manganese oxide (MnO) was coated on the surface of HPM (MHPM) by using the electroless plating technique. The HPM and MHPM were characterized by using optical microscopy (OM), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). Optical and scanning micrographs were used to monitor the surface properties of the coated layer which revealed the presence of MnO on the surface of HPM. TGA showed the presence of 4-5% of MnO in MHPM. Adsorption isotherm studies were carried out as a function of pH, initial ion concentration, and contact time, to determine the adsorption efficiency for removal of Mn2+ from contaminated water by the synthesized MHPM. The isotherm results showed that the maximum adsorption capacity of MnO-coated HPM to remove manganese contaminants from water is 8.373 mg/g. The obtained R 2 values of Langmuir isotherm and Freundlich isotherm models were 1 and 0.87, respectively. Therefore, R 2 magnitude confirmed that the Langmuir model is best suited for Mn2+ adsorption by a monolayer of MHPM adsorbent. The material developed shows higher adsorption capacity even at a higher concentration of solute ions, which is not usually observed with similar materials of this kind. Overall findings indicate that MHPM is a very potential lightweight adsorbent for removal of Mn2+ from the aqueous solution because of its low density and high surface area.

Sign in / Sign up

Export Citation Format

Share Document