Analysis of Transients in Francis Turbine Using Fourier Methods

2019 ◽  
Author(s):  
Gregor Cvijetic ◽  
Luka Culic ◽  
Hrvoje Jasak
Keyword(s):  
Francis Turbine ◽  
Fourier Methods

An Image Reconstruction System Applied to High Voltage Microscopy

1975 ◽  
Vol 33 ◽  
pp. 292-293
Author(s):  
D. E. Johnson
Keyword(s):  
High Voltage ◽  
Prior Information ◽  
Block Diagram ◽  
Three Dimensional ◽  
Real Space ◽  
Two Dimensional ◽  
Efficient Manner ◽  
Fourier Methods ◽  
Tilt Series ◽  
Methods Of Reconstruction

Increased specimen penetration; the principle advantage of high voltage microscopy, is accompanied by an increased need to utilize information on three dimensional specimen structure available in the form of two dimensional projections (i.e. micrographs). We are engaged in a program to develop methods which allow the maximum use of information contained in a through tilt series of micrographs to determine three dimensional speciman structure.In general, we are dealing with structures lacking in symmetry and with projections available from only a limited span of angles (±60°). For these reasons, we must make maximum use of any prior information available about the specimen. To do this in the most efficient manner, we have concentrated on iterative, real space methods rather than Fourier methods of reconstruction. The particular iterative algorithm we have developed is given in detail in ref. 3. A block diagram of the complete reconstruction system is shown in fig. 1.

scholarly journals Capability of Advanced Ultrasonic Inspection Technologies for Hydraulic Turbine Runners

2021 ◽  
Vol 11 (10) ◽  
pp. 4681
Author(s):  
Mohammad Ebrahim Bajgholi ◽  
Gilles Rousseau ◽  
Martin Viens ◽  
Denis Thibault
Keyword(s):  
Ultrasonic Inspection ◽  
High Stress ◽  
Welding Process ◽  
Hydraulic Turbine ◽  
Francis Turbine ◽  
Detection Rates ◽  
Critical Range ◽  
Area Of Interest ◽  
Ambitious Program ◽  
Pulse Echo

This paper presents the results of a project aimed at evaluating the performance of ultrasonic techniques for detecting flaws in Francis turbine runners. This work is the first phase of a more ambitious program aimed at improving the reliability of inspection of critical areas in turbine runners. Francis runners may be utilized to supply power during peak periods, which means that they experience additional load stress associated with start and stop sequences. Inspection during manufacturing is then of paramount importance to remove as much as feasible all flaw initiation sites before the heat treatment. This phase one objective is to collect initial data on a simplified mock-up and then to compare the experimental ultrasonic data with the results of simulations performed by CIVA, a computer simulation package. The area of interest is the region with the highest stress between the blade and the web. A welded T-joint coupon made of UNS S41500 was manufactured to represent this high-stress area. During the FCAW welding process, ceramic beads were embedded in the weld to create discontinuities whose size is in the critical range to initiate a crack. Inspection of the material was carried out by various nondestructive testing (NDT) methods namely conventional pulse-echo, phased array, total focusing method (TFM). With these results, detection rates were obtained in order to compare the effectiveness of each method.

scholarly journals Effect of the leakage flow in runner on flow characteristics of a Francis turbine model

2021 ◽  
Vol 774 (1) ◽  
pp. 012087
Author(s):  
S J Kim ◽  
Y S Choi ◽  
Y Cho ◽  
J W Choi ◽  
J J Hyun ◽  
...  
Keyword(s):  
Flow Characteristics ◽  
Francis Turbine ◽  
Leakage Flow ◽  
Turbine Model

scholarly journals A Simplified Francis Turbine for Micro Hydro Application: Design and Numerical Analysis

2021 ◽  
Vol 627 ◽  
pp. 012018
Author(s):  
Dadi Ram Dahal ◽  
Hari Prasad Neopane ◽  
Biraj Singh Thapa ◽  
Nikshan Paudel ◽  
Sailesh Chitrakar ◽  
...  
Keyword(s):  
Numerical Analysis ◽  
Francis Turbine ◽  
Application Design

scholarly journals Effect of Air Injection on the Internal Flow Characteristics in the Draft Tube of a Francis Turbine Model

Processes ◽  
2021 ◽  
Vol 9 (7) ◽  
pp. 1182
Author(s):  
Seung-Jun Kim ◽  
Yong Cho ◽  
Jin-Hyuk Kim
Keyword(s):  
Flow Rate ◽  
Draft Tube ◽  
Pressure Fluctuations ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Air Injection ◽  
Low Flow ◽  
Francis Turbine ◽  
Navier Stokes ◽  
Vortex Rope

Under low flow-rate conditions, a Francis turbine exhibits precession of a vortex rope with pressure fluctuations in the draft tube. These undesirable flow phenomena can lead to deterioration of the turbine performance as manifested by torque and power output fluctuations. In order to suppress the rope with precession and a swirl component in the tube, the use of anti-swirl fins was investigated in a previous study. However, vortex rope generation still occurred near the cone of the tube. In this study, unsteady-state Reynolds-averaged Navier–Stokes analyses were conducted with a scale-adaptive simulation shear stress transport turbulence model. This model was used to observe the effects of the injection in the draft tube on the unsteady internal flow and pressure phenomena considering both active and passive suppression methods. The air injection affected the generation and suppression of the vortex rope and swirl component depending on the flow rate of the air. In addition, an injection level of 0.5%Q led to a reduction in the maximum unsteady pressure characteristics.

Numerical Simulation of Cavitating Flow in a Francis Turbine

2008 ◽  
Author(s):  
Lingjiu Zhou ◽  
Zhengwei Wang ◽  
Yongyao Luo ◽  
Guangjie Peng
Keyword(s):  
Numerical Simulation ◽  
Transport Equation ◽  
Flow Rate ◽  
Suction Side ◽  
Cavitating Flow ◽  
Francis Turbine ◽  
Efficiency Change ◽  
Experiment Data ◽  
Calculation Results ◽  
Vapor Fraction

The 3-D unsteady Reynolds averaged Navier-tokes equations based on the pseudo-homogeneous flow theory and a vapor fraction transport-equation that accounts for non-condensable gas are solved to simulate cavitating flow in a Francis turbine. The calculation results agreed with experiment data reasonably. With the decrease of the Thoma number, the cavity first appears near the centre of the hub. At this stage the flow rate and the efficiency change little. Then the cavity near the centre of the hub grows thick and the cavities also appear on the blade suction side near outlet. With further reduce of the Thoma number the cavitation extends to the whole flow path, which causes flow rate and efficiency decrease rapidly.

Numerical Prediction of Critical Cavitation Performance in Hydraulic Turbines

2003 ◽  
Author(s):  
Sadao Kurosawa ◽  
Kiyoshi Matsumoto
Keyword(s):  
Flow Model ◽  
Flow Analysis ◽  
Prediction Method ◽  
Hydraulic Turbine ◽  
Francis Turbine ◽  
Two Phase ◽  
Cavitation Performance ◽  
Hydraulic Turbines ◽  
Critical Cavitation ◽  
Good Agreement

In this paper, numerical method for predicting critical cavitation performance in a hydraulic turbine is presented. The prediction method is based on unsteady cavitation flow analysis to use bubble two-phase flow model. The prediction of the critical cavitation performance was carried out for the aixal hydraulic turbine and the francis turbine as a typical examples. Results compared to the experiment showed a good agreement for the volume of cavity and the performance drop off and it was recognized that this method could be used as an engineering tool of a hydraulic turbine development.

Sign in / Sign up

Export Citation Format

Share Document