scholarly journals Effects of Polypropylene Fiber Content on Strength and Workability Properties of Concrete

2019 ◽  
Vol 9 (1) ◽  
pp. 7-12 ◽  
Author(s):  
Arsalan Hasan ◽  
Nyazi Maroof ◽  
Yassin Ibrahim
Keyword(s):  
Tensile Strength ◽  
Water Absorption ◽  
Volume Fraction ◽  
Dynamic Properties ◽  
Polypropylene Fiber ◽  
Plain Concrete ◽  
Fiber Content ◽  
Fiber Volume ◽  
Concrete Mix ◽  
Absorption Percentage

Low tensile strength of plain concrete is due to the inherent presence of microcracks due to drying shrinkage occurrences or other causes of volume changes in concrete. The addition of a proper amount of fibers to concrete would act as crack arrester thus improves its static or dynamic properties. In this paper, the concrete with different amount of polypropylene fiber was investigating to find out the fibers effect on its fresh and mature properties. A plain concrete mix (reference mix) prepared for comparison purposes. Nine concrete mixes were prepared with different fiber volume fraction (FVF) ranging from 0.06% to 2.16%. It has been found out that the fiber content of the concrete mix will increase compressive, splitting, and flexural strengths of the concrete at the age of 28 days. The strengths increased and reached their maximum value at a corresponding (FVF) of about 0.36%. In comparison with the reference mix, the increase in the maximum compressive strength was about 18%, while the increase in maximum splitting tensile strength was about 16% and the increase in flexural strength was about 14%. When the fiber content increased beyond the mentioned 0.36% volume fraction: The concrete strengths started to decrease due to high volume fiber interface with the cohesiveness of the concrete matrix causing difficulty in concrete compaction with lowering its workability. At fiber (FVF) of 0.96%, the concrete slump value became zero. Thus, forced vibration needed for the compaction. For each mature concrete mix density and water absorption percentage were measured. It has been noticed that with an increase of fiber dosage in the concrete mix its density will decrease leading to contrarily an increase in the water absorption percentage. This was due to an increase in air void in the concrete due to the reduction in the workability of the concrete.

Experiment Investigation on Mechanical Property of Glass Fiber Reinforced Concrete

2014 ◽  
Vol 915-916 ◽  
pp. 784-787
Author(s):  
Yan Lv
Keyword(s):  
Tensile Strength ◽  
Reinforced Concrete ◽  
Flexural Strength ◽  
Glass Fiber ◽  
Volume Fraction ◽  
Plain Concrete ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Glass Fiber Reinforced

Based on the mechanical properties experiment of the glass fiber reinforced concrete with 0%0.6%0.8% and 1% glass fiber volume fraction, the mechanics property such as tensile strength, compressive strength, flexural strength and flexural elasticity modulus are analyzed and compared with the plain concrete when the kinds of fiber content changes. The research results show that the effect of tensile strength and flexural strength can be improved to some extent, which also can serve as a reference or basis for further improvement and development the theory and application of the glass fiber reinforced concrete.

Flexural Toughness of Hybrid Fiber Reinforced High-Performance Concrete under Three-Point Bending

2013 ◽  
Vol 357-360 ◽  
pp. 1110-1114
Author(s):  
Dong Tao Xia ◽  
Xiang Kun Liu ◽  
Bo Ru Zhou
Keyword(s):  
Tensile Strength ◽  
High Performance ◽  
Steel Fiber ◽  
High Performance Concrete ◽  
Volume Fraction ◽  
Polypropylene Fiber ◽  
Fiber Reinforced ◽  
Hybrid Fiber ◽  
Fiber Volume ◽  
Flexural Toughness

A set of new hybrid fiber reinforced high-performance concrete was developed and studied by experiment. The fibers incorporated the concrete are the collection of the steel fiber, modified polypropylene fiber and polypropylene with total fiber content not more than 1%. And the compressive test, splitting tensile test and the flexural toughness test were performed on eight groups of specimens. Based on the load-deflection and load-CMOD curves and the equivalent flexural tensile strength, the effect of fiber volume fraction and hybrid mode upon concrete's mechanical properties and post-peak behavior were investigated. The test results show that the mixing of the three different fibers can increase concrete's splitting tensile strength and flexural toughness more effectively with no significantly effect on compressive strength. The mixture of the three different fibers exist the optimization problem. Based on the results of the analysis, the compatible proportion of the three fibers is 0.7% steel fiber, 0.19% modified polypropylene fiber and 0.11% polypropylene fiber.

Effects of Fiber Content and Water Ratio on the Strength of Fiber Reinforced Mortar

2012 ◽  
Vol 204-208 ◽  
pp. 3961-3964
Author(s):  
Yao Wang ◽  
Wei Hong Xuan ◽  
Yu Zhi Chen ◽  
Xiao Hong Chen ◽  
Gang Zheng
Keyword(s):  
Flexural Strength ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Polypropylene Fiber ◽  
Fiber Content ◽  
Early Age ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Cement Material ◽  
Water Ratio

The compressive and flexural strength of ordinary mortar and fiber reinforced mortar with five different pp fiber content were tested in this paper. The results show that the compressive strength reduced gradually with PP fiber increasing, and the flexural strength increased when the fiber volume fraction is no more than 0.12%. The higher water ratio can weaken the cohesiveness of the fiber and cement material, and the influence of polypropylene fiber on the flexural strength of mortar decreased after soaking. The major strength damage in the process of curing is caused in the early age and appropriate amount of fiber is beneficial to reduce strength damage.

Effect of Polypropylene Fiber on Mechanical Properties of Concrete Containing Fly Ash

2011 ◽  
Vol 346 ◽  
pp. 26-29 ◽  
Author(s):  
Hong Wei Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Modulus Of Elasticity ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Polypropylene Fiber ◽  
Splitting Tensile Strength ◽  
Fiber Volume

A designed experimental study has been conducted to investigate the effect of the fiber fraction of polypropylene fiber on the mechanical properties of concrete containing fly ash, a large number of experiments have been carried out in this study. The mechanical properties include compressive strength, splitting tensile strength and compressive modulus of elasticity. On the basis of the experimental results of the specimens of six sets of mix proportions, the mechanism of action of polypropylene fiber on these mechanical properties has been analyzed in details. The results indicate that there is a tendency of increase in the compressive strength and splitting tensile strength, and the modulus of elasticity of concrete containing fly ash decrease gradually with the increase of fiber volume fraction with appropriate content.

Static and Fatigue Strength of Resin Transfer Molded Composites

2002 ◽  
Author(s):  
Youssef Hamidi ◽  
Levent Aktas ◽  
J. David Bladwin ◽  
M. Cengiz Altan
Keyword(s):  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Volume Fraction ◽  
Fatigue Behavior ◽  
Fatigue Loading ◽  
Fiber Content ◽  
Fiber Volume ◽  
Neat Polymer ◽  
Volume Fractions ◽  
Structural Applications

Fiber reinforced polymer composites are preferred in many structural applications for their ease of production and high specific strengths. Although fatigue loading is commonly encountered in structural applications, behavior of composites under cyclic loading is less understood compared to fatigue behavior of more conventional metals and their alloys. In this work, the response of resin transfer molded (RTM) glass/epoxy composites to static tensile and fatigue loading is investigated. Center-gated, disk shaped composites are fabricated using EPON 815C epoxy resin and EPICURE 3282 curing agent. A randomly oriented, planar glass fiber preform with 0.459kg/m2 surface density is used as the reinforcement material. Two and six layers of preforms are used to achieve 7.9 and 28.9% fiber volume fractions respectively. In addition, neat polymer parts are molded without performs to study the effect of fiber content on the tensile and fatigue behavior. Initially, ultimate tensile strength (UTS) and stiffness for three different fiber volume fractions (i.e., 0, 7.9, and 28.9%) are reported. Then, fatigue tests are conducted for stress level (σmax/UTS) of 0.5 and stress ratio (σmax/σmin) of 0.1 at a test frequency of 10 Hz. Loss of stiffness and cycles to failure are the two fatigue properties investigated. As the fiber volume fraction increased from 7.9 to 28.9%, the ultimate tensile strength and stiffness increased by 140 and 100%, respectively. During fatigue loading, the stiffness gradually dropped by approximately 13% for 7.9% and 28.9% fiber volume fractions. However, neat polymer samples did not show considerable decrease in stiffness during cycling. It is also shown that the number of cycles before failure significantly increased with the fiber content.

scholarly journals Absorption and Strength Properties of Short Carbon Fiber Reinforced Mortar Composite

Buildings ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 300
Author(s):  
Md. Safiuddin ◽  
George Abdel-Sayed ◽  
Nataliya Hearn
Keyword(s):  
Tensile Strength ◽  
Carbon Fiber ◽  
Water Absorption ◽  
Carbon Fibers ◽  
Strength Properties ◽  
Fiber Content ◽  
Test Results ◽  
Air Content ◽  
Entrapped Air ◽  
Short Carbon

This paper presents the water absorption and strength properties of short carbon fiber reinforced mortar (CFRM) composite. Four CFRM composites with 1%, 2%, 3%, and 4% short pitch-based carbon fibers were produced in this study. Normal Portland cement mortar (NCPM) was also prepared for use as the control mortar. The freshly mixed mortar composites were tested for workability, wet density, and entrapped air content. In addition, the hardened mortar composites were examined for compressive strength, splitting tensile strength, flexural strength, and water absorption at the ages of 7 and 28 days. The effects of different carbon fiber contents on the tested properties were observed. Test results showed that the incorporation of carbon fibers decreased the workability and wet density, but increased the entrapped air content in mortar composite. Most interestingly, the compressive strength of CFRM composite increased up to 3% carbon fiber content and then it declined significantly for 4% fiber content, depending on the workability and compaction of the mortar. In contrast, the splitting tensile strength and flexural strength of the CFRM composite increased for all fiber contents due to the greater cracking resistance and improved bond strength of the carbon fibers in the mortar. The presence of short pitch-based carbon fibers significantly strengthened the mortar by bridging the microcracks, resisting the propagation of these minute cracks, and impeding the growth of macrocracks. Furthermore, the water absorption of CFRM composite decreased up to 3% carbon fiber content and then it increased substantially for 4% fiber content, depending on the entrapped air content of the mortar. The overall test results suggest that the mortar with 3% carbon fibers is the optimum CFRM composite based on the tested properties.

scholarly journals Multi-Scale Study of The Small-Strain Damping Ratio of Fiber-Sand Composites

Polymers ◽  
2021 ◽  
Vol 13 (15) ◽  
pp. 2476
Author(s):  
Haiwen Li ◽  
Sathwik S. Kasyap ◽  
Kostas Senetakis
Keyword(s):  
Dynamic Properties ◽  
Wide Spectrum ◽  
Damping Ratio ◽  
Polypropylene Fiber ◽  
Small Strain ◽  
Treatment Method ◽  
Fiber Content ◽  
Polypropylene Fibers ◽  
Test Results ◽  
Fiber Reinforced

The use of polypropylene fibers as a geosynthetic in infrastructures is a promising ground treatment method with applications in the enhancement of the bearing capacity of foundations, slope rehabilitation, strengthening of backfills, as well as the improvement of the seismic behavior of geo-systems. Despite the large number of studies published in the literature investigating the properties of fiber-reinforced soils, less attention has been given in the evaluation of the dynamic properties of these composites, especially in examining damping characteristics and the influence of fiber inclusion and content. In the present study, the effect of polypropylene fiber inclusion on the small-strain damping ratio of sands with different gradations and various particle shapes was investigated through resonant column (macroscopic) experiments. The macroscopic test results suggested that the damping ratio of the mixtures tended to increase with increasing fiber content. Accordingly, a new expression was proposed which considers the influence of fiber content in the estimation of the small-strain damping of polypropylene fiber-sand mixtures and it can be complementary of damping modeling from small-to-medium strains based on previously developed expressions in the regime of medium strains. Additional insights were attempted to be obtained on the energy dissipation and contribution of fibers of these composite materials by performing grain-scale tests which further supported the macroscopic experimental test results. It was also attempted to interpret, based on the grain-scale tests results, the influence of fiber inclusion in a wide spectrum of properties for fiber-reinforced sands providing some general inferences on the contribution of polypropylene fibers on the constitutive behavior of granular materials.

Performance of Bamboo Fiber Reinforced Composites: Mechanical Properties

2021 ◽  
Vol 879 ◽  
pp. 284-293
Author(s):  
Norliana Bakar ◽  
Siew Choo Chin
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Vinyl Ester ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Bamboo Fiber ◽  
Synthetic Fiber ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Volume Fractions

Fiber Reinforced Polymer (FRP) made from synthetic fiber had been widely used for strengthening of reinforced concrete (RC) structures in the past decades. Due to its high cost, detrimental to the environment and human health, natural fiber composites becoming the current alternatives towards a green and environmental friendly material. This paper presents an investigation on the mechanical properties of bamboo fiber reinforced composite (BFRC) with different types of resins. The BFRC specimens were prepared by hand lay-up method using epoxy and vinyl-ester resins. Bamboo fiber volume fractions, 30%, 35%, 40%, 45% and 50% was experimentally investigated by conducting tensile and flexural test, respectively. Results showed that the tensile and flexural strength of bamboo fiber reinforced epoxy composite (BFREC) was 63.2% greater than the bamboo fiber reinforced vinyl-ester composite (BFRVC). It was found that 45% of bamboo fiber volume fraction on BFREC exhibited the highest tensile strength compared to other BFRECs. Meanwhile, 40% bamboo fiber volume fraction of BFRVC showed the highest tensile strength between bamboo fiber volume fractions for BFRC using vinyl-ester resin. Studies showed that epoxy-based BFRC exhibited excellent results compared to the vinyl-ester-based composite. Further studies are required on using BFRC epoxy-based composite in various structural applications and strengthening purposes.

scholarly journals Tensile Mechanical Properties and Failure Modes of a Basalt Fiber/Epoxy Resin Composite Material

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Jingjing He ◽  
Junping Shi ◽  
Xiaoshan Cao ◽  
Yifeng Hu
Keyword(s):  
Tensile Strength ◽  
Composite Material ◽  
Fiber Volume Fraction ◽  
Failure Modes ◽  
Volume Fraction ◽  
Basalt Fiber ◽  
Orientation Angle ◽  
Fiber Volume ◽  
Fiber Clustering ◽  
Fiber Orientation Angle

Uniaxial tensile tests of basalt fiber/epoxy (BF/EP) composite material with four different fiber orientations were conducted under four different fiber volume fractions, and the variations of BF/EP composite material failure modes and tensile mechanical properties were analyzed. The results show that when the fiber volume fraction is constant, the tensile strength, elastic modulus, and limiting strain of BF/EP composite material all decrease with increasing fiber orientation angle. When the fiber orientation angle is constant, the tensile strength, elastic modulus, and limiting strain of BF/EP composite material all increase with increasing fiber volume fraction. A certain degree of fiber clustering appears in the epoxy resin when the basalt fiber volume fraction is >1.2%. The fiber equidistribution coefficient and clustering fiber content were used to characterize the basalt fiber clustering effect. With the increase of fiber volume fraction, the clustering fiber content gradually increased, but the fiber equidistribution coefficient decreased. Meanwhile, based on Tsai theory, a geometric model and a tensile mechanical model of the clustering fiber are established. By considering the fiber clustering effect, the BF/EP composite material tensile strength is calculated, and the calculated values are close to the experimental results.

Sign in / Sign up

Export Citation Format

Share Document