PERFORMANCE EVALUATION OF PKL (PATHOR KUCHI LEAF) ELECTRICITY FOR USE IN TELEVISION AND RADIO

A new method of electricity generation based on Pathor Kuchi (Genus:Kalanchoe,Section:Bryophyllum) Leaf has been designed and developed at the Department of Physics, Jagannath University,Dhaka- 1100,Bangladesh.For accurate sizing of Television and Radio PKL electric modules are necessary to optimize the module size for operation. It was realized that a vast majority of rural households in Bangladesh were left unelectrified by conventional gas based electricity. The field performance studies of the technical aspects, the projected specific capital cost and the average daily generation and efficiency of the PKL module have been found for both Radio and TV from collected data. Attempts have been made to correlate certain measurable parameters with anticipated performance of the PKL system. Chemical, physical and mechanical properties of the PKL, Short Circuit Current (ISC), Open Circuit Voltage (VOC),Temperature effect of the PKL malt, pH of the PKL malt, Titratable acidity of the PKL malt, Generation of PKL electricity, Storage system of the PKL electricity, Practical utilization of PKL electricity use in Load(Television and Radio), Classification of PKL, Longevity of the PKL malt for PKL electricity generation, Preparation of PKL electric unit cell, module, panel, arrays and the constituent elements of the PKL have been studied. In experimental study, it is shown that ,the pH of the PKL malt is ≈ 4.6 (without water), pH of the PKL malt is ≈ 4.8(with 10% solution), the titratable acidity of the PKL malt is ≈ 0.88% and the constituent elements/ ions of the PKL malt is Fe++ and Cl-. Most of the results have been tabulated and graphically discussed.

Download Full-text

A NEW AND SUSTAINABLE PKL ELECTRICITY

ETHICS AND INFORMATION TECHNOLOGY ◽

10.26480/etit.02.2020.173.178 ◽

2021 ◽

Author(s):

K. A. Khan ◽

Shahinul Islam ◽

M. A. Saime ◽

S. R. Rasel ◽

Sazzad Hossain

Keyword(s):

Rural Areas ◽

Electricity Generation ◽

Short Circuit ◽

Storage System ◽

Research Work ◽

Titratable Acidity ◽

Voltage Regulation ◽

Open Circuit ◽

Electricity Production ◽

Maximum Efficiency

A new method of electricity generation based on Pathor Kuchi Leaf (Genus: Kalanchoe, Section: Bryophyllum) has been developed at the Department of Physics, Jagannath University, Dhaka- 1100, Bangladesh. This electricity generation method has several advantages for smart grid over the conventional electricity production. This sustainable method is likely to generate the employment at particularly in the rural areas of where grid electricity is absent. This research work reports an invention made on Pathor Kuchi Leaf (PKL) electric power plant to enhance the PKL electricity production. The efficiency of the PKl electricity production device, Short Circuit Current ( Isc ), Open circuit Voltage ( Voc ), Temperature effect of the PKL malt, pH of the PKL malt, Titratable acidity of the PKL malt, Generation of PKL electricity, Storage system of the PKL electricity, Particular utilization of PKL electricity, I-V characteristics of the PKL, Classification of PKL, Longevity of PKL malt for PKL electricity generation, Preparation of PKL electric unit cell, module, panel, arrays and the constituent elements of the PKL, Voltage regulation, Internal resistance of the cell and efficiency of the cell have been studied. The chemical reactions of the PKL electrochemical cell have also been studied. In experimental study, it is shown that the maximum efficiency of the PKL electricity production device is ≈ 34%, the pH of the PKL malt is ≈ 4.6(without water), pH of the PKL malt is ≈ 4.8 (with 10% solution), the titratable acidity of the PKL malt is ≈ 0.88%. Most of the results have been tabulated and graphically discussed.

Download Full-text

CdTe-Based Thin Film Solar Cells: Past, Present and Future

Energies ◽

10.3390/en14061684 ◽

2021 ◽

Vol 14 (6) ◽

pp. 1684

Author(s):

Alessandro Romeo ◽

Elisa Artegiani

Keyword(s):

Thin Film ◽

Solar Cells ◽

Solar Cell ◽

Short Circuit ◽

Short Circuit Current ◽

Short Circuit Current Density ◽

Open Circuit ◽

Early Years ◽

Solar Cell Efficiency ◽

Cell Efficiency

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.

Download Full-text

GaInP/GaAs/poly-Si Multi-Junction Solar Cells by in Metal Balls Bonding

Crystals ◽

10.3390/cryst11070726 ◽

2021 ◽

Vol 11 (7) ◽

pp. 726

Author(s):

Ray-Hua Horng ◽

Yu-Cheng Kao ◽

Apoorva Sood ◽

Po-Liang Liu ◽

Wei-Cheng Wang ◽

...

Keyword(s):

Solar Cells ◽

Solar Cell ◽

Low Temperature ◽

Triple Junction ◽

Short Circuit ◽

Short Circuit Current ◽

Open Circuit ◽

Metal Line ◽

Solar Simulator ◽

Junction Solar Cell

In this study, a mechanical stacking technique has been used to bond together the GaInP/GaAs and poly-silicon (Si) solar wafers. A GaInP/GaAs/poly-Si triple-junction solar cell has mechanically stacked using a low-temperature bonding process which involves micro metal In balls on a metal line using a high-optical-transmission spin-coated glue material. Current–voltage measurements of the GaInP/GaAs/poly-Si triple-junction solar cells have carried out at room temperature both in the dark and under 1 sun with 100 mW/cm2 power density using a solar simulator. The GaInP/GaAs/poly-Si triple-junction solar cell has reached an efficiency of 24.5% with an open-circuit voltage of 2.68 V, a short-circuit current density of 12.39 mA/cm2, and a fill-factor of 73.8%. This study demonstrates a great potential for the low-temperature micro-metal-ball mechanical stacking technique to achieve high conversion efficiency for solar cells with three or more junctions.

Download Full-text

Photocurrent density and electrical properties of Bi0.5Na0.5TiO3-BaNi0.5Nb0.5O3 ceramics

Journal of Advanced Ceramics ◽

10.1007/s40145-021-0497-7 ◽

2021 ◽

Author(s):

Mingqiang Zhong ◽

Qin Feng ◽

Changlai Yuan ◽

Xiao Liu ◽

Baohua Zhu ◽

...

Keyword(s):

Electrical Properties ◽

Photovoltaic Effect ◽

Short Circuit ◽

Short Circuit Current ◽

Photocurrent Density ◽

Open Circuit ◽

Light Conditions ◽

X Ray Diffraction ◽

Solid State Method ◽

X Ray

AbstractIn this work, the (1−x)Bi0.5Na0.5TiO3-xBaNi0.5Nb0.5O3 (BNT-BNN; 0.00 ⩽ x ⩽ 0.20) ceramics were prepared via a high-temperature solid-state method. The crystalline structures, photovoltaic effect, and electrical properties of the ceramics were investigated. According to X-ray diffraction, the system shows a single perovskite structure. The samples show the normal ferroelectric loops. With the increase of BNN content, the remnant polarization (Pr) and coercive field (Ec) decrease gradually. The optical band gap of the samples narrows from 3.10 to 2.27 eV. The conductive species of grains and grain boundaries in the ceramics are ascribed to the double ionized oxygen vacancies. The open-circuit voltage (Voc) of ∼15.7 V and short-circuit current (Jsc) of ∼1450 nA/cm2 are obtained in the 0.95BNT-0.05BNN ceramic under 1 sun illumination (AM1.5G, 100 mW/cm2). A larger Voc of 23 V and a higher Jsc of 5500 nA/cm2 are achieved at the poling field of 60 kV/cm under the same light conditions. The study shows this system has great application prospects in the photovoltaic field.

Download Full-text

Ultrathin Cu(In,Ga)Se2 Solar Cells with Ag/AlOx Passivating Back Reflector

Energies ◽

10.3390/en14144268 ◽

2021 ◽

Vol 14 (14) ◽

pp. 4268

Author(s):

Jessica de Wild ◽

Gizem Birant ◽

Guy Brammertz ◽

Marc Meuris ◽

Jef Poortmans ◽

...

Keyword(s):

Surface Roughness ◽

Solar Cells ◽

Short Circuit ◽

Short Circuit Current ◽

Short Circuit Current Density ◽

Open Circuit ◽

Electron Microscopic ◽

Current Increase ◽

Time Resolved ◽

Cigs Solar Cells

Ultrathin Cu(In,Ga)Se2 (CIGS) absorber layers of 550 nm were grown on Ag/AlOx stacks. The addition of the stack resulted in solar cells with improved fill factor, open circuit voltage and short circuit current density. The efficiency was increased from 7% to almost 12%. Photoluminescence (PL) and time resolved PL were improved, which was attributed to the passivating properties of AlOx. A current increase of almost 2 mA/cm2 was measured, due to increased light scattering and surface roughness. With time of flight—secondary ion mass spectroscopy, the elemental profiles were measured. It was found that the Ag is incorporated through the whole CIGS layer. Secondary electron microscopic images of the Mo back revealed residuals of the Ag/AlOx stack, which was confirmed by energy dispersive X-ray spectroscopy measurements. It is assumed to induce the increased surface roughness and scattering properties. At the front, large stains are visible for the cells with the Ag/AlOx back contact. An ammonia sulfide etching step was therefore applied on the bare absorber improving the efficiency further to 11.7%. It shows the potential of utilizing an Ag/AlOx stack at the back to improve both electrical and optical properties of ultrathin CIGS solar cells.

Download Full-text

Enhancement of the performance of CdS/CdTe heterojunction solar cell using TiO2/ZnO bi-layer ARC and V2O5 BSF layers: A simulation approach

The European Physical Journal Applied Physics ◽

10.1051/epjap/2020200213 ◽

2020 ◽

Vol 92 (2) ◽

pp. 20901

Author(s):

Abdul Kuddus ◽

Md. Ferdous Rahman ◽

Jaker Hossain ◽

Abu Bakar Md. Ismail

Keyword(s):

Solar Cell ◽

Short Circuit ◽

Photovoltaic Performance ◽

Short Circuit Current ◽

Short Circuit Current Density ◽

Open Circuit ◽

Heterojunction Solar Cell ◽

Back Surface ◽

Heterojunction Solar Cells

This article presents the role of Bi-layer anti-reflection coating (ARC) of TiO2/ZnO and back surface field (BSF) of V2O5 for improving the photovoltaic performance of Cadmium Sulfide (CdS) and Cadmium Telluride (CdTe) based heterojunction solar cells (HJSCs). The simulation was performed at different concentrations, thickness, defect densities of each active materials and working temperatures to optimize the most excellent structure and working conditions for achieving the highest cell performance using obtained optical and electrical parameters value from the experimental investigation on spin-coated CdS, CdTe, ZnO, TiO2 and V2O5 thin films deposited on the glass substrate. The simulation results reveal that the designed CdS/CdTe based heterojunction cell offers the highest efficiency, η of ∼25% with an enhanced open-circuit voltage, Voc of 0.811 V, short circuit current density, Jsc of 38.51 mA cm−2, fill factor, FF of 80% with bi-layer ARC and BSF. Moreover, it appears that the TiO2/ZnO bi-layer ARC, as well as ETL and V2O5 as BSF, could be highly promising materials of choice for CdS/CdTe based heterojunction solar cell.

Download Full-text

Online current-sensorless estimator for PV open circuit voltage and short circuit current

Solar Energy ◽

10.1016/j.solener.2020.11.004 ◽

2021 ◽

Vol 213 ◽

pp. 198-210

Author(s):

Ahsan Nadeem ◽

Hadeed Ahmed Sher ◽

Ali Faisal Murtaza ◽

Nisar Ahmed

Keyword(s):

Open Circuit Voltage ◽

Short Circuit ◽

Short Circuit Current ◽

Open Circuit ◽

Current Sensorless

Download Full-text

A Self-Powered Nanogenerator for the Electrical Protection of Integrated Circuits from Trace Amounts of Liquid

Nano-Micro Letters ◽

10.1007/s40820-019-0338-1 ◽

2019 ◽

Vol 12 (1) ◽

Cited By ~ 3

Author(s):

Zhuang Hui ◽

Ming Xiao ◽

Daozhi Shen ◽

Jiayun Feng ◽

Peng Peng ◽

...

Keyword(s):

Integrated Circuits ◽

High Performance ◽

Printed Circuit Board ◽

Short Circuit ◽

High Sensitivity ◽

Short Circuit Current ◽

Fast Response ◽

Open Circuit ◽

Circuit Board ◽

Self Powered

Abstract With the increase in the use of electronic devices in many different environments, a need has arisen for an easily implemented method for the rapid, sensitive detection of liquids in the vicinity of electronic components. In this work, a high-performance power generator that combines carbon nanoparticles and TiO2 nanowires has been fabricated by sequential electrophoretic deposition (EPD). The open-circuit voltage and short-circuit current of a single generator are found to exceed 0.7 V and 100 μA when 6 μL of water was applied. The generator is also found to have a stable and reproducible response to other liquids. An output voltage of 0.3 V was obtained after 244, 876, 931, and 184 μs, on exposure of the generator to 6 μL of water, ethanol, acetone, and methanol, respectively. The fast response time and high sensitivity to liquids show that the device has great potential for the detection of small quantities of liquid. In addition, the simple easily implemented sequential EPD method ensures the high mechanical strength of the device. This compact, reliable device provides a new method for the sensitive, rapid detection of extraneous liquids before they can impact the performance of electronic circuits, particularly those on printed circuit board.

Download Full-text

Constructing PbS quantum dot sensitized ZnO nanorod array photoelectrodes for highly efficient photovoltaic devices

Canadian Journal of Physics ◽

10.1139/cjp-2016-0142 ◽

2016 ◽

Vol 94 (7) ◽

pp. 687-692

Author(s):

Masood Mehrabian ◽

Naser Ghasemian

Keyword(s):

Quantum Dot ◽

Short Circuit ◽

Zno Nanorods ◽

Growth Period ◽

Short Circuit Current ◽

Nanorod Array ◽

Open Circuit ◽

Zno Film ◽

Photovoltaic Properties ◽

Pbs Quantum Dot

Solar cells with ZnO film/ZnO nanorods (NRs)/PbS quantum dot (QD) photoelectrodes were constructed and various properties were studied. The ZnO NRs were grown for different periods varying from 0 (ZnO film) to 30 min (ZnO NR30) and the effect of growth period on the photovoltaic properties was investigated. The cell with ZnO film/PbS QD as photoelectrode showed the open circuit voltage VOC of 0.59 V, short circuit current density JSC of 10.06 mAcm−2, and the power conversion efficiency of 3.29% under one sun illumination (air mass 1.5 global illumination at 100 mWcm−2). In a device containing of ZnO film/ZnO NR10/PbS QD (as photoelectrode), mentioned photovoltaic parameters increased to 0.61 V, 10.47 mAcm−2 and 3.81%, respectively.

Download Full-text

Fluttering Amplitude Amplification by Utilizing Flapping Moment in Flutter-Driven Triboelectric Nanogenerator

ASME 2021 15th International Conference on Energy Sustainability ◽

10.1115/es2021-62501 ◽

2021 ◽

Author(s):

Yi Zhang ◽

Ka Chung Chan ◽

Sau Chung Fu ◽

Christopher Yu Hang Chao

Keyword(s):

Flow Velocity ◽

High Speed ◽

Aerodynamic Force ◽

Short Circuit ◽

Short Circuit Current ◽

Open Circuit ◽

Energy Output ◽

Small Scale ◽

Triboelectric Nanogenerator ◽

Peak Value

Abstract Flutter-driven triboelectric nanogenerator (FTENG) is one of the most promising methods to harvest small-scale wind energy. Wind causes self-fluttering motion of a flag in the FTENG to generate electricity by contact electrification. A lot of studies have been conducted to enhance the energy output by increasing the surface charge density of the flag, but only a few researches tried to increase the converting efficiency by enlarging the flapping motion. In this study, we show that by simply replacing the rigid flagpole in the FTENG with a flexible flagpole, the energy conversion efficiency is augmented and the energy output is enhanced. It is found that when the flag flutters, the flagpole also undergoes aerodynamic force. The lift force generated from the fluttering flag applies a periodic rotational moment on the flagpole, and causes the flagpole to vibrate. The vibration of the flagpole, in turn amplifies the flutter of the flag. Both the fluttering dynamics of the flags with rigid and flexible flagpoles have been recorded by a high-speed camera. When the flag was held by a flexible flagpole, the fluttering amplitude and the contact area between the flag and electrode plates were increased. The energy enhancement increased as the flow velocity increased and the enhancement can be 113 times when the wind velocity is 10 m/s. The thickness of the flagpole was investigated. An optimal output of open-circuit voltage reaching 1128 V (peak-to-peak value) or 312.40 V (RMS value), and short-circuit current reaching 127.67 μA (peak-to-peak value) or 31.99 μA (RMS value) at 12.21 m/s flow velocity was achieved. This research presents a simple design to enhance the output performance of an FTENG by amplifying the fluttering amplitude. Based on the performance obtained in this study, the improved FTENG has the potential to apply in a smart city for driving electronic devices as a power source for IoT applications.

Download Full-text