scholarly journals Influence of Cutting Fluid Application Frequency in Micromilling Cutting Forces

2021 ◽  
Vol 6 (3) ◽  
pp. 195-201
Author(s):  
Deborah De Oliveira ◽  
Milla Caroline Gomes ◽  
Aline Gomes Dos Santos ◽  
Marcio Bacci Da Silva
Keyword(s):  
Cutting Forces ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Fluid ◽  
Micro Milling ◽  
Depth Of Cut ◽  
Inconel 718 Alloy ◽  
Micro End Mill ◽  
Micro Parts ◽  
Application Frequency

Micromachining allows the production of parts and components on a micro scale with high precision and has become a key process to meet the growing demand for micro parts and micro components. To meet the quality requirements of the generated surfaces and reduce the cutting forces, strategies have been analysed, such as the use of the cutting fluid. Therefore, this research aimed to verify the effect of the frequency of the use of cutting fluid during the micro-milling of the Inconel 718 alloy. For this purpose, an ultra-refined cemented carbide micro end mill coated with (Al, Ti) N and 400 µm in diameter was used. A spindle speed of 20,000 rpm, a cutting speed of 13.8 m/min, a feed per tooth of 5 µm/tooth and an axial depth of cut of 40 µm were used as cutting parameters. Two frequencies of application of the cutting fluid were evaluated, corresponding to the flow rate of 40.7 and 270.0 ml/ h, in addition to the dry test. To measure the cutting forces, a Kistler dynamometer with operating range of -5 kN to +10 kN was used. In addition, the process simulation was performed using the AdvantEdge software by ThirdWave Systems. The results showed that the higher flow of the cutting fluid provided lower cutting forces and that, in dry machining, the cutting force increased significantly during the machining of a slot.

Predictive Modeling and Optimization of Cutting Forces Through RSM and Taguchi Techniques in the Turning of ASTM B574 (Hastelloy C-22)

2018 ◽  
pp. 398-417
Author(s):  
İsmail Kırbaş ◽  
Musa Peker ◽  
Gültekin Basmacı ◽  
Mustafa Ay
Keyword(s):  
Feed Rate ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Rake Angle ◽  
Orthogonal Experimental Design ◽  
Depth Of Cut ◽  
Effective Parameters ◽  
Factors Affecting ◽  
The Impact

In this chapter, the impact of cutting parameters (depth of cut, cutting speed, feed, flow, rake angle, lead angle) on cutting forces in the turning process with regard to ASTM B574 (Hastelloy C-22) material has been investigated. Variance analysis has been applied in order to determine the factors affecting the cutting forces. The optimization of the parameters affecting the surface roughness has been obtained using response surface methodology (RSM) based on the Taguchi orthogonal experimental design. The accuracy of the developed models required for the estimation of the force values (Fx, Fy, Fz) is quite successful. In this study, where the R2 value has been used as the criterion/measure, accuracy values of 93.35%, 95.03%, and 95.09% have been achieved for Fx, Fy, and Fz, respectively. As a result of the ANOVA analysis, the most effective parameters for Fx at a 95% confidence interval are depth of cut, feed rate, flow, and rake angle. The most effective parameter for Fy is depth of cut, while the most effective parameters for Fz are depth of cut, feed rate, and flow, respectively.

Cutting Forces in High Speed Milling of Hardened Steel by Coated Tool

2009 ◽  
Vol 69-70 ◽  
pp. 418-422
Author(s):  
L.D. Wu ◽  
Cheng Yong Wang ◽  
D.H. Yu ◽  
Yue Xian Song
Keyword(s):  
Cutting Forces ◽  
High Speed ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Coated Tool ◽  
Radial Depth ◽  
Solid Carbide ◽  
End Mills

Hardened steel P20 at 50 HRC is milled at high speed by TiN coated and TiAlN coated solid carbide straight end mills, and the cutting forces and tool wear are measured. The result shows that TiAlN coated tool is more suitable for cutting hardened steel at high speed. Then the hardened steel is milled under different cutting parameters. It is indicated that the effect of cutting speed on cutting forces is small, but the effect of cutting speed on machine vibration should be considered. Increase feed per tooth or radial depth of cut will increase the cutting forces.

scholarly journals Optimization of Atomized Spray Cutting Fluid Eco-Friendly Turning of Inconel 718 Alloy Using ARAS and CODAS Methods

2021 ◽  
Author(s):  
Vinothkumar Sivalingam ◽  
Ganeshkumar Poogavanam ◽  
Yuvaraj Natarajan ◽  
Jie Sun
Keyword(s):  
Surface Roughness ◽  
Power Consumption ◽  
Tool Life ◽  
Inconel 718 ◽  
Cutting Speed ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Parameter Setting ◽  
Inconel 718 Alloy ◽  
Desirability Index

Abstract Atomized spray cutting fluid (ASCF) is a sophisticated machining technique that achieves higher productivity, enhanced surface quality, extended tool life, and cost benefits. This research aims to analyze the influence of cutting process parameters on Inconel 718 alloy turning in dry and ASCF cutting environments. The critical machining indices such as surface roughness, machining cost, power consumption, and tool life were analyzed concerning these two cooling environments. The cutting parameters were optimized using desirability functional analysis and two types of multicriteria decision making (MCDM) method, such as additive ratio assessment method (ARAS) and combinative distance-based assessment (CODAS) method, were investigated. The composite desirability index (CD) of optimum parameter setting(A2B1C2D2) is improved by 6.34 % compared to the initial parameter setting (A2B1C2D1). The optimum parameters from the MCDM technique are obtained as a cutting speed of 200 m/min, feed rate of 0.08 mm/rev, and depth of cut of 0.2 mm under ASCF environment. ASCF machining significantly minimize the surface roughness, machining cost and power consumption, maximize the tool life by about 16%, 51%, 17% and 48% respectively as compared with dry machining

scholarly journals An Investigation into the Effect of Electro-Contact Heating in the Machining of Low-Rigidity Thin-Walled Micro-Machine Parts

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4427
Author(s):  
Antoni Świć ◽  
Arkadiusz Gola ◽  
Olga Orynycz ◽  
Karol Tucki
Keyword(s):  
Control System ◽  
Feed Rate ◽  
Cutting Forces ◽  
Flank Wear ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Contact Heating ◽  
Thin Walled ◽  
Micro Machine

Low-rigidity thin-walled parts are components of many machines and devices, including high precision electric micro-machines used in control and tracking systems. Unfortunately, traditional machining methods used for machining such types of parts cause a significant reduction in efficiency and in many cases do not allow obtaining the required accuracy parameters. Moreover, they also fail to meet modern automation requirements and are uneconomical and inefficient. Therefore, the aim of provided studies was to investigate the dependency of cutting forces on cutting parameters and flank wear, as well as changes in cutting forces induced by changes in heating current density and machining parameters during the turning of thin-walled parts. The tests were carried out on a specially designed and constructed turning test stand for measuring cutting forces and temperature at specific cutting speed, feed rate, and depth of cut values. As part of the experiments, the effect of cutting parameters and flank wear on cutting forces, and the effect of heating current density and turning parameters on changes in cutting forces were analyzed. Moreover, the effect of cutting parameters (depth of cut, feed rate, and cutting speed) on temperature has been determined. Additionally, a system for controlling electro-contact heating and investigated the relationship between changes in cutting forces and machining time in the operations of turning micro-machine casings with and without the use of the control system was developed. The obtained results show that the application of an electro-contact heating control system allows to machine conical parts and semi-finished products at lower cutting forces and it leads to an increase in the deformation of the thin-walled casings caused by runout of the workpiece.

Cutting forces analysis of micro-milling process on Inconel 718 – a finite element approach

2020 ◽  
Vol 11 (02) ◽  
pp. 2050011
Author(s):  
Padmaja Tripathy ◽  
Kalipada Maity
Keyword(s):  
Finite Element ◽  
Cutting Forces ◽  
Inconel 718 ◽  
Cutting Speed ◽  
Fem Analysis ◽  
Milling Process ◽  
Machining Process ◽  
Micro Milling ◽  
Depth Of Cut ◽  
Machining Parameters

This paper presents a modeling and simulation of micro-milling process with finite element modeling (FEM) analysis to predict cutting forces. The micro-milling of Inconel 718 is conducted using high-speed steel (HSS) micro-end mill cutter of 1mm diameter. The machining parameters considered for simulation are feed rate, cutting speed and depth of cut which are varied at three levels. The FEM analysis of machining process is divided into three parts, i.e., pre-processer, simulation and post-processor. In pre-processor, the input data are provided for simulation. The machining process is further simulated with the pre-processor data. For data extraction and viewing the simulated results, post-processor is used. A set of experiments are conducted for validation of simulated process. The simulated and experimental results are compared and the results are found to be having a good agreement.

scholarly journals Effects of Machining Parameters on the Quality in Machining of Aluminium Alloys Thin Plates

Metals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 927 ◽  
Author(s):  
Irene Del Sol ◽  
Asuncion Rivero ◽  
Antonio J. Gamez
Keyword(s):  
Cutting Forces ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Thin Plates ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Final Thickness ◽  
Machined Parts ◽  
Chemical Milling ◽  
Skin Panels

Nowadays, the industry looks for sustainable processes to ensure a more environmentally friendly production. For that reason, more and more aeronautical companies are replacing chemical milling in the manufacture of skin panels and thin plates components. This is a challenging operation that requires meeting tight dimensional tolerances and differs from a rigid body machining due to the low stiffness of the part. In order to fill the gap of literature research on this field, this work proposes an experimental study of the effect of the depth of cut, the feed rate and the cutting speed on the quality characteristics of the machined parts and on the cutting forces produced during the process. Whereas surface roughness values meet the specifications for all the machining conditions, an appropriate cutting parameters selection is likely to lead to a reduction of the final thickness deviation by up to 40% and the average cutting forces by up to a 20%, which consequently eases the clamping system and reduces machine consumption. Finally, an experimental model to control the process quality based on monitoring the machine power consumption is proposed.

Prediction of the Cutting Forces on Stainless Steels When Using a Turning Process

2003 ◽  
Author(s):  
Zulay Cassier ◽  
Patricia Mun˜oz-Escalona ◽  
Jannelly Moreno
Keyword(s):  
Stainless Steels ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Depth Of Cut ◽  
Turning Process ◽  
High Corrosion Resistance ◽  
Aisi 304 ◽  
Heat Treated

Stainless steels have a great application in the manufacturing process especially due to their characteristic high corrosion resistance. The machining of these materials, the study of the cutting forces, and the power required for the cutting are important parameters to be evaluated. Their relationship with other cutting variables process is crucial for the optimization of the machining process. The results of this research are empirical expressions relating cutting parameters (cutting speed, feed rate and depth of cut) to cutting forces for each stainless steel studied, AISI 304, AISI 420 and AISI 420HT (HT: Heat treated). A general expression was also developed which includes the mechanical properties of these stainless steels. These results enable the user to predict cutting forces when using a turning process.

Micro-Milling of Hardened AISI D2 Tool Steel

2012 ◽  
Vol 445 ◽  
pp. 62-67 ◽  
Author(s):  
J.B. Saedon ◽  
S.L. Soo ◽  
D.K. Aspinwall ◽  
A. Barnacle
Keyword(s):  
Tool Wear ◽  
Tool Steel ◽  
Feed Rate ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Operating Conditions ◽  
Micro Milling ◽  
Burr Formation ◽  
Depth Of Cut ◽  
Aisi D2

The paper presents an experimental investigation into the slotting of hardened AISI D2 (~62HRC) tool steel using 0.5mm diameter coated (TiAlN) tungsten carbide (WC) end mills. SEM analysis of tool morphology and coating integrity was undertaken on all tools prior to testing. Tool wear details are given based on resulting cutter diameter and slot width reduction. In addition, cutting forces are also presented together with details of workpiece burr formation. A full factorial experimental design was used with variation of cutting speed, feed rate and depth of cut, with results evaluated using analysis of variance (ANOVA) techniques. Parameter levels were chosen based on microscale milling best practice and results from preliminary testing. Main effects plots and percentage contribution ratios (PCR) are included for the main factors. Cutting speed was shown to have the greatest effect on tool wear (33% PCR). When operating at 50m/min cutting speed with a feed rate of 8µm/rev and a depth of cut of 55µm, cutter diameter showed a reduction of up to 82µm for a 520mm cut length. SEM micrographs of tool wear highlighted chipping / fracture as the primary wear mode with adhered workpiece material causing further attritious wear when machining was continued up to 2.6m cut length. All tests produced burrs on the top edges of the slots which varied in size / width to a lesser or greater degree. Under the most severe operating conditions, burr width varied from approximately 50µm to more than 220µm over the 520mm cut length. Cutting forces in general were less than 12N up to test cessation.

Experimental Investigations of Cutting Parameters Influence on Cutting Forces and Surface Roughness of Quartz Glass

2013 ◽  
Vol 641-642 ◽  
pp. 367-370
Author(s):  
Gui Qiang Liang ◽  
Fei Fei Zhao
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Diamond Wheel ◽  
Experimental Investigations ◽  
Depth Of Cut ◽  
Feed Force

Abstract In the present study, an attempt has been made to investigate the effect of cutting parameters (cutting speed, feed rate and depth of cut) on cutting forces (feed force, thrust force and cutting force) and surface roughness in milling of Quartz glas using diamond wheel. The cutting process in the up-cut milling of glass is discussed and the cutting force measured. The cutting force gradually increases with the cutter rotation at the beginning of the cut, and oscillates about a constant mean value after a certain undeformed chip thickness. The results show that cutting forces and surface roughness do not vary much with experimental cutting speed in the range of 55–93 m/min. The suggested models of cutting forces and surface roughness and adequately map within the limits of the cutting parameters considered.

The Effect of Cutting Parameters on Power Consumption during Turning Nickel Based Alloy

2013 ◽  
Vol 845 ◽  
pp. 799-802 ◽  
Author(s):  
Rusdi Nur ◽  
M.Y. Noordin ◽  
S. Izman ◽  
Denni Kurniawan
Keyword(s):  
Power Consumption ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Turning Process ◽  
Environmental Aspect ◽  
Minimum Power Consumption ◽  
Nickel Based Alloy

Machining process should also consider environmental aspect, with power consumption as one of the criteria. Cutting parameters can be optimized to minimize power consumption. This paper takes a study on turning of nickel-based hastelloy under dry condition (no cutting fluid) which varies cutting speed (150, 200, and 250 m/min) and depth of cut (0.5, 1.0, and 1.5 mm). Power consumption of particular machining process at various cutting parameters was derived and calculated. It was found that minimum power consumption was shown when the turning process was performed at the lowest cutting speed and depth of cut.

Sign in / Sign up

Export Citation Format

Share Document