scholarly journals An Investigation into the Effect of Electro-Contact Heating in the Machining of Low-Rigidity Thin-Walled Micro-Machine Parts

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4427
Author(s):  
Antoni Świć ◽  
Arkadiusz Gola ◽  
Olga Orynycz ◽  
Karol Tucki
Keyword(s):  
Control System ◽  
Feed Rate ◽  
Cutting Forces ◽  
Flank Wear ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Contact Heating ◽  
Thin Walled ◽  
Micro Machine

Low-rigidity thin-walled parts are components of many machines and devices, including high precision electric micro-machines used in control and tracking systems. Unfortunately, traditional machining methods used for machining such types of parts cause a significant reduction in efficiency and in many cases do not allow obtaining the required accuracy parameters. Moreover, they also fail to meet modern automation requirements and are uneconomical and inefficient. Therefore, the aim of provided studies was to investigate the dependency of cutting forces on cutting parameters and flank wear, as well as changes in cutting forces induced by changes in heating current density and machining parameters during the turning of thin-walled parts. The tests were carried out on a specially designed and constructed turning test stand for measuring cutting forces and temperature at specific cutting speed, feed rate, and depth of cut values. As part of the experiments, the effect of cutting parameters and flank wear on cutting forces, and the effect of heating current density and turning parameters on changes in cutting forces were analyzed. Moreover, the effect of cutting parameters (depth of cut, feed rate, and cutting speed) on temperature has been determined. Additionally, a system for controlling electro-contact heating and investigated the relationship between changes in cutting forces and machining time in the operations of turning micro-machine casings with and without the use of the control system was developed. The obtained results show that the application of an electro-contact heating control system allows to machine conical parts and semi-finished products at lower cutting forces and it leads to an increase in the deformation of the thin-walled casings caused by runout of the workpiece.

Predictive Modeling and Optimization of Cutting Forces Through RSM and Taguchi Techniques in the Turning of ASTM B574 (Hastelloy C-22)

2018 ◽  
pp. 398-417
Author(s):  
İsmail Kırbaş ◽  
Musa Peker ◽  
Gültekin Basmacı ◽  
Mustafa Ay
Keyword(s):  
Feed Rate ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Rake Angle ◽  
Orthogonal Experimental Design ◽  
Depth Of Cut ◽  
Effective Parameters ◽  
Factors Affecting ◽  
The Impact

In this chapter, the impact of cutting parameters (depth of cut, cutting speed, feed, flow, rake angle, lead angle) on cutting forces in the turning process with regard to ASTM B574 (Hastelloy C-22) material has been investigated. Variance analysis has been applied in order to determine the factors affecting the cutting forces. The optimization of the parameters affecting the surface roughness has been obtained using response surface methodology (RSM) based on the Taguchi orthogonal experimental design. The accuracy of the developed models required for the estimation of the force values (Fx, Fy, Fz) is quite successful. In this study, where the R2 value has been used as the criterion/measure, accuracy values of 93.35%, 95.03%, and 95.09% have been achieved for Fx, Fy, and Fz, respectively. As a result of the ANOVA analysis, the most effective parameters for Fx at a 95% confidence interval are depth of cut, feed rate, flow, and rake angle. The most effective parameter for Fy is depth of cut, while the most effective parameters for Fz are depth of cut, feed rate, and flow, respectively.

scholarly journals Online Tool Wear Monitoring by the Analysis of Cutting Forces in Transient State for Dry Machining of Ti6Al4V Alloy

Metals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 1014 ◽  
Author(s):  
Sánchez Hernández ◽  
Trujillo Vilches ◽  
Bermudo Gamboa ◽  
Sevilla Hurtado
Keyword(s):  
Tool Wear ◽  
Feed Rate ◽  
Cutting Forces ◽  
Flank Wear ◽  
Cutting Speed ◽  
Transient State ◽  
Cutting Parameters ◽  
Dry Machining ◽  
Crater Wear ◽  
Force Amplitude

In this work, the analysis of the cutting speed and feed rate influence on tool wear and cutting forces in Ti6Al4V alloy dry machining is presented. The study has been focused on the machining in a transient state. The tool wear mechanisms, tool wear intensity and cutting forces evolution have been analyzed as a function of the cutting parameters. Experimental results show that the main cutting force amplitude exhibits a general trend to increase with both cutting parameters. Crater wear was more evident at high cutting speeds, whereas flank wear was present on the whole interval of the cutting parameters analyzed. Furthermore, the cutting speed shows a slightly higher influence on crater wear and the feed rate shows a higher influence on flank wear. Finally, several experimental parametric models have been obtained. These models allow predicting the evolution of crater and flank tool wear, as well as the cutting forces, as a function of the cutting parameters. Additionally, a model that allows monitoring the tool wear on the machining transient state as a function of the main cutting force amplitude has been developed.

Wear Characteristic and Life of Al2O3/(W,Ti)C Ceramic Tool in Turning Iron-Based P/M Composites

2010 ◽  
Vol 26-28 ◽  
pp. 1052-1055
Author(s):  
Li Fa Han ◽  
Sheng Guan Qu
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Empirical Model ◽  
Feed Rate ◽  
Flank Wear ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Ceramic Tool ◽  
Iron Based

The wear characteristics and life of Al2O3/(W,Ti)C ceramic tool in turning NbCp-reinforced iron-based P/M composites was investigated. Experimental results indicate that cutting parameters have an influence on tool wear, among which cutting speed and depth of cut seem to be more prominent. The maximum flank wear rapidly increases as the increase in cutting speed and depth of cut. While, it increases gradually as the decrease in feed rate. Meanwhile, an empirical model of tool life is established, from which the influence of cutting speed and depth of cut on tool life is far greater than that of feed rate. Also from the empirical model, the preferable range of cutting parameters was obtained.

scholarly journals EFFECT OF CUTTING PARAMETERS ON CUTTING FORCES IN TURNING OF CPM 10V STEEL

2021 ◽  
Vol 24 (2) ◽  
pp. 5-8
Author(s):  
Anđelko Aleksić ◽  
◽  
Milenko Sekulić ◽  
Marin Gostimirović ◽  
Dragan Rodić ◽  
...  
Keyword(s):  
Feed Rate ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Physical And Mechanical Properties ◽  
Cutting Parameters ◽  
Radial Force ◽  
Depth Of Cut ◽  
Feed Force ◽  
Cnc Lathe ◽  
Method Analysis

The objective of this paper is to investigate the effect of cutting parameters on cutting forces during turning of CPM 10V steel with coated cutting tool. Machining of CPM 10V steel and finding a suitable tool is very challenging due to its physical and mechanical properties, especially since the machining of this material has not been extensively researched. The experiments were carried out using an Index GU -600 CNC lathe and the cutting forces were measured in process. A three-factorial three-level experimental design was used for the experiments. Statistical method analysis of variance (ANOVA) is applied to study the effects of cutting speed, feed rate, and depth of cut on cutting forces. The results of this study show that depth of cut has the most significant effect on main force and radial force, while feed rate and cutting speed have the most significant effect on feed force. The developed model can be used in the machining industry to predict and analyze cutting parameters for optimal cutting forces.

scholarly journals Analysis of Surface Roughness and Cutting Forces in Hard Turning of 42CrMo4 Steel using Taguchi and RSM Method

Mechanika ◽  
2020 ◽  
Vol 26 (3) ◽  
pp. 231-241 ◽  
Author(s):  
Mustafa ÖZDEMİR ◽  
Mehmet Tuncay KAYA ◽  
Hamza Kemal AKYILDIZ
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Cutting Forces ◽  
Tangential Force ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Radial Force ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Feed Force

In this study, effects of cutting speed (V), feed rate (f), depth of cut (a) and tool tip radius (R) on  surface roughness (Ra, Rz, and Rt) and cutting forces (radial force (Fx), tangential force (Fy), and feed force (Fz)) in hard finish turning processes of hardened 42CrMo4 (52 HRC) material was investigated experimentally. Taguchi’s mixed level parameter design (L18) is used for the experimental design (2x1,3x3). The signal-to-noise ratio (S/N) was used in the evaluation of test results.  By using Taguchi method, cutting parameters giving optimum surface roughness and cutting forces were determined. Regression analyses are applied to predict surface roughness and cutting forces. Analysis of variance (ANOVA) is used to determine the effects of the machining parameters on surface roughness and cutting forces. According to ANOVA analysis, the most important cutting parameters were found to be feed rate for surface roughness and depth of cut among cutting forces.  By conducting validation experiments, optimization was seen to be applied successfully.

scholarly journals Validation and optimization of cutting parameters for Ti-6Al-4V turning operation using DEFORM 3D simulations and Taguchi method

2021 ◽  
Vol 8 ◽  
pp. 5
Author(s):  
Japheth Oirere Obiko ◽  
Fredrick Madaraka Mwema ◽  
Michael Oluwatosin Bodunrin
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
Signal To Noise Ratio ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Interface Temperature ◽  
Depth Of Cut ◽  
Optimization Of Cutting Parameters ◽  
The Relationship

In this study, we show that optimising cutting forces as a machining response gave the most favourable conditions for turning of Ti-6Al-4V alloy. Using a combination of computational methods involving DEFORM simulations, Taguchi Design of Experiment (DOE) and analysis of variance (ANOVA), it was possible to minimise typical machining response such as the cutting force, cutting power and chip-tool interface temperature. The turning parameters that were varied in this study include cutting speed, depth of cut and feed rate. The optimum turning parameter combinations that would minimise the machining responses were established by using the “smaller the better” criterion and selecting the highest value of Signal to Noise Ratio. Confirmatory simulation revealed that using cutting speed of 120 m/min, 0.25 mm depth of cut and 0.1 mm/rev feed rate, the lowest cutting force of 88.21 N and chip-tool interface temperature of 387.24 °C can be obtained. Regression analysis indicated that the highest correlation coefficient of 0.97 was obtained between cutting forces and the turning parameters. The relationship between cutting forces and the turning parameters was linear since first-order regression model was sufficient.

Modeling and Analysis of Cutting Forces in Hard Turning T250 Steel Using CBN Tools

2010 ◽  
Vol 154-155 ◽  
pp. 694-700
Author(s):  
Yue Ding ◽  
Xi Bin Wang ◽  
Li Jing Xie ◽  
Hao Yang
Keyword(s):  
Cutting Force ◽  
Analysis Of Variance ◽  
Feed Rate ◽  
Cutting Forces ◽  
Hard Turning ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Modeling And Analysis ◽  
Feed Force

The objective of this paper is to study the cutting forces in hard turning T250 steel with CBN tools. Experiments based on the Box-Behnken design were conducted to develop the cutting forces models by response surface methodology (RSM). Significance tests of the model are performed by the analysis of variance (ANOVA). It is also discussed the effects of cutting parameters (cutting speed, feed rate and depth of cut) on the cutting force components. The results show that the models can fit experimental data via analysis of variance. The most important cutting parameter is depth of cut, followed by feed rate, while the effect of cutting speed can be neglected. Compared to cutting force and feed force, thrust force is the largest. In addition, the cutting forces generated by the uncoated tool are smaller than by the coated one due to tool wear.

scholarly journals Turning of Inconel 718 Using Liquid Nitrogen: Multi-objective Optimization of Cutting Parameters Using RSM

2021 ◽  
Author(s):  
Behzad Eskandari ◽  
Sukanta Bhowmick ◽  
Ahmet Alpas
Keyword(s):  
Cutting Force ◽  
Liquid Nitrogen ◽  
Feed Rate ◽  
Inconel 718 ◽  
Flank Wear ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Multi Objective Optimization ◽  
Cryogenic Cutting

Abstract The objective of this research was to investigate the effectiveness of application of liquid nitrogen (LN2) in turning of Inconel 718 compared to flooded cutting and select suitable LN2 cutting parameters using response surface methodology (RSM). The results of turning experiments conducted by spraying LN2 to the cutting area of Inconel 718 bar showed that using either low or high cutting parameters, cutting performance of Inconel 718 under the cryogenic condition was generally worse than the flooded cutting. However, using the medium cutting parameters the cutting performance was as good as flooded cutting showing the values of 90 N of cutting force, 60 µm of flank wear and 0.5-0.6 µm of surface roughness (Ra). These parameters were further optimized using desirability function of RSM to determine the set of parameters that provide the lowest cutting force, flank wear and Ra and the highest material removal rate (MRR) under cryogenic cutting. Analysis of variance (ANOVA) performed on the developed regression models showed that cutting speed was the significant factor on cutting force. Feed rate was the most influential parameter on flank wear. Feed rate and depth of cut was significant factors affecting Ra. Multi-objective optimization showed that a cutting speed of 87 m/min, a feed rate of 0.06 mm/rev and a depth of cut of 0.37 mm constituted the optimum cutting parameters for achieving the, cutting force of 78 N, flank wear of 58 µm, Ra of 0.49 µm and the MRR of 1.97 cm3/min under cryogenic cutting condition.

Cutting Temperature and Cutting Forces Investigation Based on the Taguchi Design Method when High-Speed Milling of Titanium Matrix Composites with PCD Tool

2016 ◽  
Vol 836-837 ◽  
pp. 168-174 ◽  
Author(s):  
Ying Fei Ge ◽  
Hai Xiang Huan ◽  
Jiu Hua Xu
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
High Speed ◽  
Volume Fraction ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth

High-speed milling tests were performed on vol. (5%-8%) TiCp/TC4 composite in the speed range of 50-250 m/min using PCD tools to nvestigate the cutting temperature and the cutting forces. The results showed that radial depth of cut and cutting speed were the two significant influences that affected the cutting forces based on the Taguchi prediction. Increasing radial depth of cut and feed rate will increase the cutting force while increasing cutting speed will decrease the cutting force. Cutting force increased less than 5% when the reinforcement volume fraction in the composites increased from 0% to 8%. Radial depth of cut was the only significant influence factor on the cutting temperature. Cutting temperature increased with the increasing radial depth of cut, feed rate or cutting speed. The cutting temperature for the titanium composites was 40-90 °C higher than that for the TC4 matrix. However, the cutting temperature decreased by 4% when the reinforcement's volume fraction increased from 5% to 8%.

Effects of Insert Nose Radius and Processing Cutting Parameter on the Surface Roughness of Aisi 316 Stainless Steel

2010 ◽  
Vol 447-448 ◽  
pp. 51-54
Author(s):  
Mohd Fazuri Abdullah ◽  
Muhammad Ilman Hakimi Chua Abdullah ◽  
Abu Bakar Sulong ◽  
Jaharah A. Ghani
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Finish ◽  
Feed Rate ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Aisi 316

The effects of different cutting parameters, insert nose radius, cutting speed and feed rates on the surface quality of the stainless steel to be use in medical application. Stainless steel AISI 316 had been machined with three different nose radiuses (0.4 mm 0.8 mm, and 1.2mm), three different cutting speeds (100, 130, 170 m/min) and feed rates (0.1, 0.125, 0.16 mm/rev) while depth of cut keep constant at (0.4 mm). It is seen that the insert nose radius, feed rates, and cutting speed have different effect on the surface roughness. The minimum average surface roughness (0.225µm) has been measured using the nose radius insert (1.2 mm) at lowest feed rate (0.1 mm/rev). The highest surface roughness (1.838µm) has been measured with nose radius insert (0.4 mm) at highest feed rate (0.16 mm/rev). The analysis of ANOVA showed the cutting speed is not dominant in processing for the fine surface finish compared with feed rate and nose radius. Conclusion, surface roughness is decreasing with decreasing of the feed rate. High nose radius produce better surface finish than small nose radius because of the maximum uncut chip thickness decreases with increase of nose radius.

Sign in / Sign up

Export Citation Format

Share Document