scholarly journals A Novel Modified Switched Inductor Boost Converter with Reduced Switch Voltage Stress

2020 ◽  
Author(s):  
Shima Sadaf ◽  
Nasser Al-Emadi ◽  
Atif Iqbal ◽  
Mohammad Meraj ◽  
Mahajan Sagar Bhaskar
Keyword(s):  
Output Voltage ◽  
Low Voltage ◽  
Electric Utility ◽  
Boost Converter ◽  
Conversion Ratio ◽  
Total Output ◽  
Dc Microgrid ◽  
Power Circuit ◽  
Voltage Stress ◽  
Utility Grid

DC-DC power converters are necessary to step-up the voltage or current with high conversion ratio for many applications e.g. photovoltaic and fuel cell energy conversion, uninterruptible power supply, DC microgrid, automobile, high intensity discharged lamp ballast, hybrid vehicle, etc. in order to use low voltage sources. In this project, a modified SIBC (mSIBC) is proposed with reduced voltage stress across active switches. The proposed mSIBC configuration is transformerless and simply derived by replacing one diode of the classical switched inductor structure with an active switch. As a result, mSIBC required low voltage rating active switches, as the total output voltage is shared between two active switches. Moreover, the proposed mSIBC is low in cost, provides higher efficiency and required the same number of components compared to the classical SIBC. The experimental results are presented which validated the theoretical analysis and functionality, and the efficiency of the designed converter is 97.17%. The proposed mSIBC converter provides higher voltage conversion ratio compared to classical converters e.g. boost, buck-boost, cuk, and SEPIC. The newly designed configurations will aid the intermediate power stage between the renewable sources and utility grid or high voltage DC or AC load. Since, the total output voltage is distributed among the two active switches, low voltage rating switches can be employed to design the power circuit of the proposed converter. The classical boost converter or recently proposed switched inductor based boost converter can be replaced by the proposed mSIBC converter in real-time applications such as DC microgrid, DC-DC charger, battery backup system, UPS, EV, an electric utility grid. The proposed power circuitry is cost effective, compact in size, easily diagnostic, highly efficient and reliable.

Design and Analysis of a High-Efficiency Two-Phase Interleaved Boost Converter with Modified Conversion Ratio and Low Voltage Stress

2021 ◽  
pp. 2150161
Author(s):  
Mriganka Biswas ◽  
Somanath Majhi ◽  
Harshal Nemade
Keyword(s):  
High Efficiency ◽  
Low Voltage ◽  
Load Condition ◽  
Boost Converter ◽  
Conversion Ratio ◽  
Duty Ratio ◽  
Two Phase ◽  
Voltage Stress ◽  
Interleaved Boost Converter ◽  
In Series

The paper presents a two-phase interleaved boost converter (IBC) providing higher step-up conversion ratio compared to the conventional IBC. The circuit consists of a crossly connected diode-capacitor cell which provides the extra boost up. The two identical capacitors of the cell are charged in parallel and discharged in series providing high voltage gain at considerably low duty ratio. Switching operations, ripple and average currents through inductors are analyzed in continuous conduction mode (CCM). Ripple in input current is also improved. The voltage stress across the semiconductor devices is less in the proposed converter. Also, boundary load condition is derived. Small-signal modeling is carried out and a control circuit is enabled in the voltage mode control framework. Power losses are analyzed and 96.53[Formula: see text] efficiency is achieved. Finally, the proposed converter is designed and implemented, and experimental results are provided.

Fully-Integrated High-Conversion-Ratio Dual-Output Voltage Boost Converter With MPPT for Low-Voltage Energy Harvesting

2016 ◽  
Vol 51 (10) ◽  
pp. 2398-2407 ◽  
Author(s):  
Toshihiro Ozaki ◽  
Tetsuya Hirose ◽  
Hiroki Asano ◽  
Nobutaka Kuroki ◽  
Masahiro Numa
Keyword(s):  
Energy Harvesting ◽  
Output Voltage ◽  
Low Voltage ◽  
Boost Converter ◽  
Conversion Ratio ◽  
High Conversion ◽  
Fully Integrated ◽  
High Conversion Ratio

scholarly journals Novel High-Efficiency High Step-Up DC–DC Converter with Soft Switching and Low Component Voltage Stress for Photovoltaic System

Processes ◽  
2021 ◽  
Vol 9 (7) ◽  
pp. 1112
Author(s):  
Yu-En Wu ◽  
Jyun-Wei Wang
Keyword(s):  
High Voltage ◽  
Output Voltage ◽  
High Efficiency ◽  
Low Voltage ◽  
Leakage Inductance ◽  
Power Switch ◽  
Half Wave Voltage ◽  
Half Wave ◽  
Voltage Stress ◽  
Voltage Doubler

This study developed a novel, high-efficiency, high step-up DC–DC converter for photovoltaic (PV) systems. The converter can step-up the low output voltage of PV modules to the voltage level of the inverter and is used to feed into the grid. The converter can achieve a high step-up voltage through its architecture consisting of a three-winding coupled inductor common iron core on the low-voltage side and a half-wave voltage doubler circuit on the high-voltage side. The leakage inductance energy generated by the coupling inductor during the conversion process can be recovered by the capacitor on the low-voltage side to reduce the voltage surge on the power switch, which gives the power switch of the circuit a soft-switching effect. In addition, the half-wave voltage doubler circuit on the high-voltage side can recover the leakage inductance energy of the tertiary side and increase the output voltage. The advantages of the circuit are low loss, high efficiency, high conversion ratio, and low component voltage stress. Finally, a 500-W high step-up converter was experimentally tested to verify the feasibility and practicability of the proposed architecture. The results revealed that the highest efficiency of the circuit is 98%.

scholarly journals Quadratic Boost Converter

2021 ◽  
Vol 9 (VII) ◽  
pp. 2010-2014
Author(s):  
Mamidala Hemanth Reddy
Keyword(s):  
Output Voltage ◽  
Semiconductor Device ◽  
Low Voltage ◽  
Input Voltage ◽  
Boost Converter ◽  
Voltage Gain ◽  
Practical Utilization ◽  
Analysis And Design ◽  
Simulink Model ◽  
Grid Connection

The output voltage from the sustainable energy like photovoltaic (PV) arrays and fuel cells will be at less amount of level. This must be boost considerably for practical utilization or grid connection. A conventional boost converter will provides low voltage gain while Quadratic boost converter (QBC) provides high voltage gain. QBC is able to regulate the output voltage and the choice of second inductor can give its current as positive and whereas for boost increases in the voltage will not able to regulate the output voltage. It has low semiconductor device voltage stress and switch usage factor is high. Analysis and design modeling of Quadratic boost converter is proposed in this paper. A power with 50 W is developed with 18 V input voltage and yield 70 V output voltage and the outcomes are approved through recreation utilizing MATLAB/SIMULINK MODEL.

scholarly journals A non‐isolated DC‐DC converter with low voltage stress and high step‐down voltage conversion ratio

2021 ◽  
Author(s):  
Stylianos P. Syrigos ◽  
Georgios C. Christidis ◽  
Theodoros P. Mouselinos ◽  
Emmanuel C. Tatakis
Keyword(s):  
Low Voltage ◽  
Conversion Ratio ◽  
Voltage Stress ◽  
Step Down ◽  
Voltage Conversion

scholarly journals Implementation of Buck-Boost Converter as Low Voltage Stabilizer at 15 V

2019 ◽  
Vol 9 (4) ◽  
pp. 2230
Author(s):  
Suwarno Suwarno ◽  
Tole Sutikno
Keyword(s):  
Power Electronics ◽  
Wind Power ◽  
Output Voltage ◽  
Low Voltage ◽  
Input Voltage ◽  
Boost Converter ◽  
Voltage Stabilizer ◽  
Voltage Regulator ◽  
Output Current ◽  
Converter Design

<p>This paper presents the implementation of the buck-boost converter design which is a power electronics applications that can stabilize voltage, even though the input voltage changes. Regulator to stabilize the voltage using PWM pulse that triger pin 2 on XL6009. In this design of buck-boost converter is implemented using the XL6009, LM7815 and TIP2955. LM7815 as output voltage regulator at 15V with 1A output current, while TIP2955 is able to overcome output current up to 5A. When the LM7815 and TIP2955 are connected in parallel, the converter can increase the output current to 6A.. Testing is done using varied voltage sources that can be set. The results obtained from this design can be applied to PV (Photovoltaic) and WP (Wind Power), with changes in input voltage between 3-21V dc can produce output voltage 15V.</p>

scholarly journals Modified Multi Input Multilevel DC-DC Boost Converter for Hybrid Energy Systems

2020 ◽  
Vol 9 (4) ◽  
pp. 1067-1072
Keyword(s):  
Output Voltage ◽  
Low Voltage ◽  
Complex Structure ◽  
Energy Systems ◽  
Input Voltage ◽  
Boost Converter ◽  
Design Parameters ◽  
Hybrid Energy ◽  
Hybrid Energy Systems ◽  
Constant Output

DC-DC converters are playing an important role in designing of Electric Vehicles, integration of solar cells and other DC applications. Contemporary high power applications use multilevel converters that have multi stage outputs for integrating low voltage sources. Conventional DC-DC converters use single source and have complex structure while using for Hybrid Energy Systems. This paper proposes a multi-input, multi-output DC-DC converter to produce constant output voltage at different input voltage conditions. This topology is best suitable for hybrid power systems where the output voltage is variable due to environmental conditions. It reduces the requirement of magnetic components in the circuit and also reduces the switching losses. The proposed topology has two parts namely multi-input boost converter and level-balancing circuit. Boost converter increases the input voltage and Level Balancing Circuit produce Multi output. Equal values of capacitors are used in Level Balancing Circuit to ensure the constant output voltage at all output stages. The operating modes of each part are given and the design parameters of each part are calculated. Performance of the proposed topology is verified using MATLAB/Simulink simulation which shows the correctness of the analytical approach. Hardware is also presented to evaluate the simulation results.

Modeling and stability study of a high frequency and high efficiency photovoltaic DC boost converter

2020 ◽  
Vol 20 (3) ◽  
pp. 817-826
Author(s):  
Shengshan Li ◽  
Ming Li ◽  
Liangliang Liu
Keyword(s):  
Power Generation ◽  
High Frequency ◽  
Output Voltage ◽  
High Efficiency ◽  
Boost Converter ◽  
Stability Study ◽  
Power Circuit ◽  
Point Tracking ◽  
Photovoltaic Power ◽  
Power Generation Systems

Many practical photovoltaic power generation systems with higher output voltage levels rely on photovoltaic DC boost converters with high frequency and high efficiency, which performance directly affect the conversion efficiency of photovoltaic power generation systems. This paper investigates a high-frequency and high-efficiency photovoltaic DC boost converter, which adopts the Boost full-bridge isolation circuit topology with active clamps. The conductance increment method is used as the maximum power point tracking algorithm. The small signal models of its power circuit and control circuit are established to obtain the system model and analyze its stability. The simulation results indicate that the ripple coefficient of output current is less than 3%, and the ripple coefficient of output voltage is less than 5%, which meets the stability requirements.

Maximum Boost Control for 7-level Z-source Cascaded H-Bridge Inverter

2017 ◽  
Vol 8 (2) ◽  
pp. 739
Author(s):  
R. Palanisamy ◽  
K. Vijayakumar
Keyword(s):  
Output Voltage ◽  
Single Phase ◽  
Boost Converter ◽  
Voltage Source ◽  
Constant Voltage ◽  
Harmonic Content ◽  
Duty Cycles ◽  
Voltage Stress ◽  
Power Switches ◽  
Boost Control

This paper proposes maximum boost control for 7-level z-source cascaded h-bridge inverter and their affiliation between voltage boost gain and modulation index. Z-source network avoids the usage of external dc-dc boost converter and improves output voltage with minimised harmonic content. Z-source network utilises distinctive LC impedance combination with 7-level cascaded inverter and it conquers the conventional voltage source inverter. The maximum boost controller furnishes voltage boost and maintain constant voltage stress across power switches, which provides better output voltage with variation of duty cycles. Single phase 7-level z-source cascaded inverter simulated using matlab/simulink.

Sign in / Sign up

Export Citation Format

Share Document