scholarly journals Pengaruh pemesinan laju tinggi keadaan kering terhadap pertumbuhan aus sisi (VB) pahat karbida berlapis (tialn/tin) pada pembubutan paduan aluminium 6061

2018 ◽  
Vol 16 (2) ◽  
pp. 51
Author(s):  
Sunarto Sunarto ◽  
Sri Mawarni
Keyword(s):  
High Speed ◽  
Cutting Tool ◽  
Flank Wear ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Condition ◽  
Coating Materials ◽  
High Cutting Speed ◽  
Titanium Nitride Coating ◽  
Cnc Lathe

AbstrakPemesinan laju tinggi yang diindikasikan dengan kecepatan potong tinggi pada proses pembubutan keadaan kering menjadi bahasan utama pada penelitian ini. Kecepatan potong (Vc) merupakan salah satu penyebab meningkatnya temperatur pemotongan dan akan mempengaruhi daya tahan alat potong. Akibat temperatur pemotongan yang tinggi pahat akan mengalami kerusakan salah satunya berupa Aus Sisi (VB). VB akan tumbuh secara terus menerus seiring dengan waktu pemotongan. Tujuan penelitian ini adalah untuk mengetahui pengaruh pemesinan laju tinggi terhadap laju pertumbuhan VB selama proses pembubutan paduan Aluminium 6061. Metode yang digunakan dalam penelitian ini adalah dengan menggunakan pahat karbida (Wc+Co) yang dilapisi dengan bahan pelapis Titanium Aluminium Nitrida dan Titanium Nitrida (TiAlN/TiN) menggunakan mesin bubut CNC serta membagi tiga kondisi pemotongan yaitu pada kecepatan potong 800 m/menit, 1000 m/menit dan 1200 m/menit. Hasil yang dicapai dari kondisi pemotongan tersebut adalah pada kecepatan potong 1200 m/menit menghasilkan ukuran VB yang lebih besar jika dibandingkan dengan kecepaatan potong 800 m/menit dan 1000 m/menit dengan waktu pemotongan masing-masing selama enam menit.Kata Kunci: Kecepatan Potong (Vc), Aus Sisi (VB), Alat PotongAbstractHigh speed machining which is indicated by high cutting speed in the dry lathe process becomes the main discussion in this study. The cutting speed (Vc) is one of the causes of increasing the cutting temperature and will affect the durability of the cutting tool. Due to high cutting temperature the cutting tool will suffer damage one of them is Flank Wear (VB). VB will grow continuously along with the cutting time. The purpose of this research is to know the effect of high speed machining to growth rate of VB during the process of Aluminum 6061 alloy. The method used in this research is by using  cutting tool (Wc + Co) coated with Titanium Aluminum Nitride and Titanium Nitride coating materials (TiAlN / TiN) using CNC lathe and dividing the three cutting conditions ie at cutting speed of 800 m / min, 1000 m / min and 1200 m / min. The result of the cutting condition is at a cutting speed of 1200 m / min resulting in a larger VB size when compared to 800 m / min cutting speed and 1000 m / min with each cutting time of six minutes.Keywords: Cutting Speed (Vc), Flank Wear (VB), Cutting Tool

High-Speed Capturing of Stress Distribution of Workpiece under Ultrasonically Assisted Cutting Condition

2014 ◽  
Vol 1017 ◽  
pp. 747-752
Author(s):  
Hiromi Isobe ◽  
Keisuke Hara
Keyword(s):  
Stress Distribution ◽  
Cutting Force ◽  
High Speed ◽  
Cutting Tool ◽  
Light Emission ◽  
Cutting Speed ◽  
Cutting Condition ◽  
Photoelastic Method ◽  
Intermittent Cutting ◽  
Ultrasonic Vibration Cutting

This paper reports the stress distribution inside the workpiece under ultrasonic vibration cutting (UVC) condition. Many researchers have reported the improvement of tool wear, burr generation and surface integrity by reduction of time-averaged cutting force under UVC condition. However general dynamometers have an insufficient frequency band to observe the processing phenomena caused by UVC. In this paper, stress distribution inside the workpiece during UVC was observed by combining the flash light emission synchronized with ultrasonically vibrating cutting tool and the photoelastic method. Instantaneous stress distribution during UVC condition was observed. Because UVC induced an intermittent cutting condition, the stress distribution changed periodically and disappeared when the tool leaved from the workpiece. It was found that instantaneous maximum cutting force during UVC condition was smaller than quasi-static cutting force during conventional cutting when the cutting speed was less than 500 mm/min.

Machinability Investigation in High Speed Turning of Powder Metallurgy Nickel-Based Superalloy with Sialon Ceramic Inserts

2010 ◽  
Vol 139-141 ◽  
pp. 805-808 ◽  
Author(s):  
Yang Qiao ◽  
Xing Ai ◽  
Zhan Qiang Liu ◽  
Jun Zhao
Keyword(s):  
Powder Metallurgy ◽  
Thermal Shock ◽  
High Speed ◽  
Cutting Tool ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Temperature Strength ◽  
Sialon Ceramic ◽  
Nickel Based Superalloy

An experimental investigation was carried out to understand the behavior of a powder metallurgy nickel-based superalloy when machined with sialon ceramic insert tools. Turning experiments were carried out at different cutting speeds and feed rates while depth of cut was kept constant. Cutting tool performance was evaluated with respect to temperature and cutting forces generated during turning, and tool wear. The sialon ceramic cutting tool showed high performance when increasing cutting speed, the machining experiments showed that sialon ceramic tools performed better at cutting speed up to 80 m/min. Abrasion and adhesion was the dominant wear mechanisms. Chipping on the tool rake and flank faces, as well as catastrophic failure under thermal shock and mechanical loading, was also observed in experiments. As cutting temperature was very high when turning powder metallurgy nickel-based superalloy, good high-temperature strength and thermal shock resistance were indispensable to the cutting tools for machinging this kind of material.

Effect of Cryogenic Minimum Quantity Lubrication (CMQL) on Cutting Temperature and Tool Wear in High-Speed End Milling of Titanium Alloys

2010 ◽  
Vol 34-35 ◽  
pp. 1816-1821 ◽  
Author(s):  
Yu Su ◽  
Ning He ◽  
Liang Li
Keyword(s):  
Tool Wear ◽  
Titanium Alloys ◽  
High Speed ◽  
End Milling ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Minimum Quantity Lubrication ◽  
Minimum Quantity ◽  
High Cutting Speed ◽  
Cryogenic Minimum Quantity Lubrication

Cryogenic minimum quantity lubrication (CMQL) is a kind of green cooling/lubrication technique, which consists of the application of a small amount of lubricant (6-100 ml/h), delivered in a refrigerated compressed gas stream to the cutting zone. This paper experimentally investigates the effect of CMQL on cutting temperature and tool wear in high-speed end milling of titanium alloys. Comparative experiments were conducted under different cooling/lubrication conditions, i.e. dry milling, refrigerated air cutting, and CMQL. The refrigerated gas equipment was manufactured based on composite refrigeration method to provide the refrigerated air. The experimental results show that application of CMQL resulted in drastic reduction in cutting temperature and tool wear especially when machining titanium alloys at a high cutting speed.

Study The Effect of Cutting Conditions (Cutting Speed, Depth of Cut, Feed ) on The Wear of Cutting Tool Bit Turning Machine

2013 ◽  
Vol 1 (2) ◽  
pp. 44-55
Author(s):  
Niema H Elmosawi ◽  
Shalan Gannam Al ◽  
Hamid H. Ali
Keyword(s):  
High Temperature ◽  
Cutting Tool ◽  
Flank Wear ◽  
Cutting Speed ◽  
Wear Test ◽  
Cutting Edge ◽  
Cutting Conditions ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Test Results

The aim of the work is to study the effect of cutting condition on cutting bit of the turning machine while working on different metal ,Through using a special type of commonly used cutting tool bit in (HSS) due to the high qualifications it is characterized by cutting ,and its endurance of high temperature .Two types of metal are used in cutting (Aluminum, Mild steel),relying on the working conditions used in the machine(feed, cutting speed، depth of cut),while conducting working processes via using cooling liquid ,and without it .The wear test results shown that there are two types of wear measured by the (tool micker microscope) :Flank wear and Greater wear, are formed on the cutting edge of the tool bits as a result of the great effect of cutting conditions on the tool bit and the high temperature of the chips ;in addition to the occurrence of resulting edge on the cutting edge of the tool bits in the process of cutting aluminum , with the use of cooling liquids which prolong the of cutting tool and decrease the periods of re-grinding the cutting tool bit. 

Experimental Study in HSM of Titanium Alloy TC4-DT

2011 ◽  
Vol 697-698 ◽  
pp. 102-106 ◽  
Author(s):  
Q. Shi ◽  
Ning He ◽  
Liang Li
Keyword(s):  
Titanium Alloy ◽  
Tool Life ◽  
High Speed ◽  
Cutting Tool ◽  
Flank Wear ◽  
Cutting Temperature ◽  
Milling Parameters ◽  
Series Of Experiments ◽  
Damage Tolerant ◽  
Better Than

In this paper, a series of experiments were carried out on normal and high speed milling of a new damage-tolerant titanium alloy. The effects of milling parameters on cutting force and cutting temperature were investigated. The tool life of three commonly used cutters, such as WK10, WMG40 and WXN15, were studied. Result shows that the tool life of cutter WXN15 was the longest one when using the same flank wear VB as a standard, and cutter WK10 had a longer too life than cutter WMG40. Thus cutter WXN15 was the most suitable cutting tool to machining TC4-DT, and cutter WK10 was better than cutter WMG40.

Simulation on Cutting Temperature during High-Speed Milling Aluminum Alloy 7055

2013 ◽  
Vol 328 ◽  
pp. 486-490 ◽  
Author(s):  
Liang Tan ◽  
Chang Feng Yao ◽  
Wei Zuo ◽  
Dao Xia Wu
Keyword(s):  
Aluminum Alloy ◽  
Theoretical Basis ◽  
High Speed ◽  
Cutting Tool ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Element Model ◽  
Milling Process ◽  
High Speed Milling ◽  
Milling Parameters

To optimize the parameters of high-speed milling of aluminum alloy 7055 and provide a theoretical basis for cutting temperature control, a finite element model of high-speed milling process of aluminum alloy 7055 was developed with AdvantEdge. Based on these models, the effect of milling parameters on cutting temperature is investigated by single factor experiments. And the temperature distribution of workpiece and cutting tool is predicted. The results show that the highest temperature occurs at close to the tool tip in the rack face, the temperature increases with an increase in cutting speed and feed per tooth, while other parameters have a less significant effect on cutting temperature.

Toughening Mechanisms and Wear Behavior of a TiC Whisker Toughening Alumina Ceramic Cutting Tool Composite

2012 ◽  
Vol 500 ◽  
pp. 634-639 ◽  
Author(s):  
Bing Qiang Liu ◽  
Chuan Zhen Huang ◽  
Ai Ling Sun
Keyword(s):  
Cutting Tool ◽  
Flank Wear ◽  
Wear Behavior ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
High Fracture Toughness ◽  
High Fracture ◽  
Toughening Mechanisms ◽  
Interesting Phenomenon ◽  
Ceramic Cutting Tool

Toughening mechanisms and flank wear behavior of a TiC whisker toughening Al2O3-based ceramic cutting tool composite were investigated. The results showed that the wear behavior of the tool composite was greatly influenced by the whisker toughening mechanisms, of which the toughening effects on the composite can increase with increasing cutting temperature. As a result, the tool composite could still possess enough high fracture toughness and flexure strength at high cutting temperature, which resulted in an interesting phenomenon that the wear resistance of the tool composite at higher cutting speed was higher than that of itself at lower cutting speed.

High-Speed Turning of Titanium Matrix Composites with PCD and Carbide Tools

2013 ◽  
Vol 770 ◽  
pp. 39-44 ◽  
Author(s):  
Ying Fei Ge ◽  
Jiu Hua Xu ◽  
Yu Can Fu
Keyword(s):  
Tool Life ◽  
Cutting Forces ◽  
High Speed ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Condition ◽  
Matrix Composites ◽  
Carbide Tool ◽  
High Speed Turning ◽  
Speed Range

High-speed turning tests were performed on vol.10%(TiCp+TiBw)/TC4 composite (TMC) in the speed range of 60-120m/min using PCD and carbide tools to investigate the tool life, tool wear, cutting temperatures and cutting forces. The results showed that the carbide tool was not suit for the machining of TMC. Tool life of PCD was confined to 12 min for all the cutting conditions. Flank wear increased obviously with the increasing cutting speed especially when the cutting speed surpassed 80m/min. PCD tool mainly took place chipping, peeling, abrasive wear and adhesive wear at the rake face and flank. The cutting temperatures of carbide were about 1.5-2.0 times higher than that of the PCD. Under the same cutting condition, cutting temperature of TMC was nearly 100°C higher than that of the TC4 matrix. The cutting forces were confined to 130N and 150N for the PCD and carbide tool respectively. For the carbide the cutting forces slightly decreased when the cutting speed increased from 60m/min to 120m/min. When using the worn tool, the cutting forces significantly decreased with the increasing cutting speed especially for the peripheral force component.

High-Speed Machining of Ti-6Al-4V With a Micro Textured Cutting Tool Focusing on Coolant Behaviors

2020 ◽  
Author(s):  
Mitsuru Hasegawa ◽  
Tatsuya Sugihara
Keyword(s):  
High Speed ◽  
Metal Cutting ◽  
Production Efficiency ◽  
Cutting Tool ◽  
Failure Process ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Fluid ◽  
High Speed Machining ◽  
Textured Surfaces

Abstract In the cutting of Ti-6Al-4V alloy, the cutting speed is limited as a high cutting temperature leads to severe tool wear and short tool life, resulting in poor production efficiency. However, some recent literature has reported that various beneficial effects can be provided by forming micro-textures on the tool surface in the metal cutting process. In this study, in order to achieve high-performance machining of Ti-6Al-4V, we first investigated the mechanism of the tool failure process for a cemented carbide cutting tool in high-speed turning of Ti-6Al-4V. Based on the results, cutting tools with micro textured surfaces were developed under the consideration of a cutting fluid action. A series of experiments showed that the textured rake face significantly suppresses both crater wear and flank wear. In addition, optimum texture structures and the mechanism of the texture effects in high-speed machining of Ti-6Al-4V alloy were discussed.

scholarly journals Failure and Control of PCBN Tools in the Process of Milling Hardened Steel

Metals ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 885
Author(s):  
Guangyue Wang ◽  
Xianliang Zhou ◽  
Xuefeng Wu ◽  
Jing Ma
Keyword(s):  
Failure Mechanism ◽  
High Speed ◽  
Failure Modes ◽  
Flank Wear ◽  
Cutting Speed ◽  
Machining Efficiency ◽  
Tool Failure ◽  
Low Speed ◽  
High Cutting Speed ◽  
Pcbn Tools

The polycrystalline cubic boron nitride (PCBN) milling tool can be used in the mold industry to replace cemented carbide tools to improve machining efficiency and quality. It is necessary to study the tool wear and failure mechanism to increase machining efficiency and extend tool life. Cr12MoV is used to analyze the failure form of PCBN tools in the interrupted cutting of hardened steels at low and high speed conditions in milling experiments. Experimental results show that the failure forms of PCBN tools include chipping and flank wear at low speed, and the failure modes at high speed are flank wear, the surface spalling of the rake face, and the fatigue failure on the flank face. The failure mechanism of different failure forms is analyzed by observing the surface morphology of the tool and using the theory of fracture mechanics. The results show that a high cutting speed should be selected to avoid the early damage of low speed and achieve better application of PCBN tools. At high cutting speed, tool failure is mainly caused by mechanical wear, diffusion wear, and oxidation wear. Moreover, a fatigue crack will occur at the cutting edge on the chamfered tool under thermal–mechanical coupling because of the intergranular fracture of the CBN grain and binder. A large area of accumulated fatigue damage may appear due to the influence of alternating mechanical stress and thermal stress. Finally, the control method to avoid tool failure is presented.

Sign in / Sign up

Export Citation Format

Share Document