scholarly journals Synthesis and Characterization of Hydroxyapatite from Duck Eggshell by Wet Precipitation Process

2021 ◽  
Vol 3 (1) ◽  
pp. 8-11
Author(s):  
Yelmida Azis ◽  
Cory Dian Alfarisi ◽  
Komalasari Komalasari ◽  
Khairat Khairat ◽  
Yusnimar Sahan
Keyword(s):  
Xrd Analysis ◽  
Precipitation Method ◽  
Molar Ratio ◽  
Precipitation Process ◽  
Stable Form ◽  
X Ray Diffraction ◽  
Precipitated Calcium Carbonate ◽  
X Ray ◽  
Inorganic Mineral

Hydroxyapatite (HAp, Ca10(PO4)6(OH)2) is the most stable form of calcium phosphate and widely used in various medical applications, mainly in orthopedics and dentistry due to its close similarities with the inorganic mineral component of bone and teeth. This study aims to synthesize hydroxyapatite from duck eggshell using the precipitation method. The duck eggshell was calcined, hydrated (slaking) and underwent carbonation to form Precipitated Calcium Carbonate (PCC).  Afterwards, (NH4)2HPO4 was added to produce HAp by varying the molar ratio of Ca/P by 1.67, 1.77 and 1.87 and stirring speed by 200, 250, 300rpm under basic condition (pH 10 – 11). The best results were obtained at a molar ratio of 1.77 with 200rpm stirring speed. Furthermore, the X-ray Diffraction (XRD) analysis showed that its crystals were hexagonal with sizes of 23.062nm, in the absence of other crystalline phases. Therefore, the hydroxyapatite was obtained in the agglomerates form with a specific surface area of ??55.929m2/g.

SYNTHESIS AND CHARACTERIZATION OF α-Fe2O3@ATO NANOCOMPOSITE PARTICLES

2008 ◽  
Vol 15 (05) ◽  
pp. 545-550 ◽  
Author(s):  
YIN-CUN ZHU ◽  
JI-SEN JIANG
Keyword(s):  
Weight Ratio ◽  
Precipitation Method ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Nanocomposite Particles ◽  
X Ray ◽  
Homogeneous Precipitation Method ◽  
Treatment Conditions ◽  
Transmission Electron

α- Fe 2 O 3@ATO (antimony doped tin oxide) nanocomposite particles with core–shell structure were prepared by homogeneous precipitation method using monodispersed α- Fe 2 O 3 (hematite) nanoparticles as cores, SnCl 4 · 5 H 2 O and SbCl 3 as the precursor of the shell. The morphology and structure of the nanocomposite particles were studied with transmission electron microscopy and X-ray diffraction, respectively. The electricity properties of the nanocomposite were also investigated in terms of coating amount, molar ratio of element Sb to Sn , and heat treatment conditions. The results showed that the conditions of ATO/α- Fe 2 O 3 (weight ratio) = 70%, n( Sb )/n( Sn ) = 10%, calcined at 700°C for 1 h were optimal for the conductivity of the nanocomposite.

Synthesis and Characterization of Ni/Mg/Al Mixed Oxides Obtained by Co-precipitation

2012 ◽  
Vol 1372 ◽  
Author(s):  
G. Martínez-Lozano ◽  
T. Kryshtab ◽  
M. Hesiquio Garduño ◽  
A. Kryvko
Keyword(s):  
Mixed Oxides ◽  
Xrd Analysis ◽  
Diffraction Peak ◽  
Precipitation Method ◽  
Particle Sizes ◽  
Extended Defects ◽  
X Ray Diffraction ◽  
X Ray ◽  
Co Precipitation

ABSTRACTNi/Mg/Al mixed oxides were obtained from hydrotalcite-like precursors by thermal decomposition at 400º, 600º and 800ºC using co-precipitation method at pH 7. The mixed oxides were characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM), and Energy-dispersive X-ray spectroscopy (EDS) techniques. XRD analysis revealed the formation of NixMg1-xO (x = 0 - 1), α-Al2O3 and traces of MgAl2O4 (NiAl2O4) phases. The diffraction peak positions for MgO or NiO oxides were shifted towards 2θ values higher than simulated for pure bulk oxides that can be attributed to the possible presence of lattice vacancies or surface compressive stress. The evaluated grain size by XRD technique was about 8 -10 nm. It was also detected the presence of microstrains that can be associated with the presence of extended defects in the grains. SEM observations showed that the particles of oxides are formed as agglomerates with the particle sizes of 50 nm up to 200 nm. EDS detected the presence of Mg2+, Ni2+, and Al3+ cations and oxygen in all particles independently on their size. The obtained results revealed the presence of mixture of Ni/Mg/Al oxides in each particle obtained. The oxides calcined at temperatures of 400º and 600ºC were unstable and under air storage they revert to the precursor. The incorporation of Ni2+ in Mg-Al mixed oxides leads to stability of the compounds calcined at 800ºC.

Characterization and A Preliminary Study of TiO2 Synthesis from Lampung Iron Sand

2020 ◽  
Vol 849 ◽  
pp. 113-118
Author(s):  
Yayat Iman Supriyatna ◽  
Slamet Sumardi ◽  
Widi Astuti ◽  
Athessia N. Nainggolan ◽  
Ajeng W. Ismail ◽  
...  
Keyword(s):  
Food Packaging ◽  
Xrd Analysis ◽  
Major Elements ◽  
Raw Material ◽  
Solid Residue ◽  
X Ray Diffraction ◽  
X Ray ◽  
Leaching Solution ◽  
Ti Content

The purpose of this study is to characterize Lampung iron sand and to conduct preliminary experiments on the TiO2 synthesis which can be used for the manufacturing of functional food packaging. The iron sand from South Lampung Regency, Lampung Province that will be utilized as raw material. The experiment was initiated by sieving the iron sand on 80, 100, 150, 200 and 325 mesh sieves. Analysis using X-Ray Fluorescence (XRF) to determine the element content and X-Ray Diffraction (XRD) to observe the mineralization of the iron sand was conducted. The experiment was carried out through the stages of leaching, precipitation, and calcination. Roasting was applied firstly by putting the iron sand into the muffle furnace for 5 hours at a temperature of 700°C. Followed by leaching using HCl for 48 hours and heated at 105°C with a stirring speed of 300 rpm. The leaching solution was filtered with filtrate and solid residue as products. The solid residue was then leached using 10% H2O2 solution. The leached filtrate was heated at 105°C for 40 minutes resulting TiO2 precipitates (powder). Further, the powder was calcined and characterized. Characterization of raw material using XRF shows the major elements of Fe, Ti, Mg, Si, Al and Ca. The highest Ti content is found in mesh 200 with 9.6%, while iron content is about 80.7%. While from the XRD analysis, it shows five mineral types namely magnetite (Fe3O4), Rhodonite (Mn, Fe, Mg, Ca) SiO3, Quart (SiO2), Ilmenite (FeOTiO2) and Rutile (TiO2). The preliminary experiment showed that the Ti content in the synthesized TiO2 powder is 21.2%. The purity of TiO2 is low due to the presence of Fe metal which is dissolved during leaching, so that prior to precipitation purification is needed to remove impurities such as iron and other metals.

Controlled Synthesis of Different Morphologies of SrWO4 Crystals via a Surfactant-Assisted Hydrothermal Precipitation Method

2013 ◽  
Vol 785-786 ◽  
pp. 449-454
Author(s):  
Yan Zhao ◽  
Chun Yan Wu ◽  
Dan Qin ◽  
Xin Lai ◽  
Si Wu ◽  
...  
Keyword(s):  
Ph Value ◽  
Precipitation Method ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Experimental Parameters ◽  
Infrared Spectrometer ◽  
Luminescent Spectra ◽  
Hydrothermal Precipitation ◽  
Surfactant Assisted

SrWO4 octahedrons, flowers, bundles, ellipsoids and dendrites had been successfully synthesized via surfactant-assisted method. The products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), photo-luminescent spectra techniques (PL) and fourier transrform infrared spectrometer (FTIR). By through various comparison experiments, it can be found that some related experimental parameters including the reagent concentration, [Sr2+]/[WO42-] molar ratio (R), aging temperature and the pH value had great influences on morphology of the products.

scholarly journals Synthesis and characterization of apatite silicated powders with wet precipitation method

2021 ◽  
Vol 234 ◽  
pp. 00106
Author(s):  
Houda Labjar ◽  
Hassan Chaair
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Analytical Techniques ◽  
Precipitation Method ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Wet Precipitation ◽  
Scanning Electron

The synthesis of apatite silicated Ca10(PO4)6-x(SiO4)x(OH)2-x (SiHA) with 0≤x≤2 was investigated using a wet precipitation method followed by heat treatment using calcium carbonate CaCO3 and phosphoric acid H3PO4 and silicon tetraacetate SiC8H20O4 (TEOS) in medium of water ethanol, with three different silicate concentrations. After drying, the samples are ground and then characterized by different analytical techniques like X-ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR) and Scanning electron Microscopy (SEM) and chemical analysis.

Production and Characterization of HVOF Sprayed NiCr-TiC Coatings Using SHS Powder Feedstock

2000 ◽  
Author(s):  
M.T. Blatchford ◽  
A.J. Horlock ◽  
D.G. McCartney ◽  
P.H. Shipway ◽  
J.V. Wood
Keyword(s):  
Thermal Spraying ◽  
Xrd Analysis ◽  
Powder Size ◽  
Coating Properties ◽  
X Ray Diffraction ◽  
Hvof Spraying ◽  
X Ray ◽  
Wear Rates ◽  
Powder Feedstock

Abstract In this paper, the production of NiCr-TiC powder by SHS, suitable for HVOF spraying, is discussed together with results on the microstructure and coating properties. Compacts for SHS were prepared by mixing elemental Ti and C with pre-alloyed Ni-20wt.% Cr powder to give an overall composition of 35wt.% NiCr and 65wt.% TiC. These were then ignited and a self-sustaining reaction proceeded to completion. Reacted compacts were crushed, sieved, and classified to give feedstock powders in size ranges of 10-45 µm and 45-75 µm. All powder was characterized prior to spraying based on particle size distribution, x-ray diffraction (XRD), and scanning electron microscopy (SEM/EDS). Thermal spraying was performed using both H2 and C3H6 as fuel gases in a UTP/Miller Thermal HVOF system. The resulting coatings were characterized by SEM and XRD analysis, and the microstructures correlated with powder size and spray conditions. Abrasive wear was determined by a modified 'dry sand rubber wheel' (DSRW) test and wear rates were measured. It has been found that wear rates comparable to those of HVOF sprayed WC-17wt% Co coatings can be achieved.

Stability of sodalite relative to nepheline in NaCl–H2O brines at 750 °C: Implications for hydrothermal formation of sodalite

2020 ◽  
Vol 58 (1) ◽  
pp. 3-18 ◽  
Author(s):  
Jonathan B. Schneider ◽  
David M. Jenkins
Keyword(s):  
Infrared Spectroscopy ◽  
Constant Temperature ◽  
Molar Ratio ◽  
Standard State ◽  
X Ray Diffraction ◽  
Cage Structure ◽  
X Ray ◽  
Brine Concentration

ABSTRACT Formation of the feldspathoid sodalite (Na6Al6Si6O24·2NaCl) by reaction of nepheline (NaAlSiO4) with NaCl-bearing brines was investigated at 3 and 6 kbar and at a constant temperature of 750 °C to determine the brine concentration at which sodalite forms with variation in pressure. The reaction boundary was located by reaction-reversal experiments in the system NaAlSiO4–NaCl–H2O at a brine concentration of 0.16 ± 0.08 XNaCl [= molar ratio NaCl/(NaCl + H2O)] at 3 kbar and at a brine concentration of 0.35 ± 0.03 XNaCl at 6 kbar. Characterization of the sodalite using both X-ray diffraction and infrared spectroscopy after treatment in these brines indicated no obvious evidence of water or hydroxyl incorporation into the cage structure of sodalite. The data from this study were combined with earlier results by Wellman (1970) and Sharp et al. (1989) at lower (1–1.5 kbar) and higher (7–8 kbar) pressures, respectively, on sodalite formation from nepheline and NaCl which models as a concave-down curve in XNaCl – P space. In general, sodalite buffers the concentration of neutral aqueous NaCl° in the brine to relatively low values at P < 4 kbar, but NaCl° increases rapidly at higher pressures. Thermochemical modeling of these data was done to determine the activity of the aqueous NaCl° relative to a 1 molal (m) standard state, demonstrating very low activities (<0.2 m, or 1.2 wt.%) of NaCl° at 3 kbar and lower, but rising to relatively high activities (>20 m, or 54 wt.%) of NaCl° at 6 kbar or higher. The results from this study place constraints on the concentration of NaCl° in brines coexisting with nepheline and sodalite and, because of the relative insensitivity of this reaction to temperature, can provide a convenient geobarometer for those localities where the fluid compositions that formed nepheline and sodalite can be determined independently.

Synthesis, Structural Analysis of Cadmium Sulphide Nanocrystallites

2019 ◽  
Vol 969 ◽  
pp. 169-174
Author(s):  
R. Sivanand ◽  
S. Chellammal ◽  
S. Manivannan
Keyword(s):  
Size Variation ◽  
Cadmium Sulphide ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
Precipitation Method ◽  
Capping Agent ◽  
Energy Dispersive Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

In this paper, the effect of size variation of cadmium sulphide nanocrystallites which have been prepared by precipitation method is analyzed. These prepared samples were studied using X-ray diffraction (XRD), Scanning electron microscopy (SEM), and Energy dispersive analysis of spectroscopy (EDAX) techniques. SEM analysis represents the morphological nature of prepared samples and EDAX indicates the confirmation of elements present in the sample. XRD analysis determines the size of the samples and identifies the structure using miller indices (h k l values) of the nanocrystallies matches with JCPDS. From the XRD analysis, the size variation which depends on dopant, capping agent are discussed and corresponding results are reported in this paper.

scholarly journals Influence of Selected Saccharides on the Precipitation of Calcium-Vaterite Mixtures by the CO2 Bubbling Method

Crystals ◽  
2019 ◽  
Vol 9 (2) ◽  
pp. 117 ◽  
Author(s):  
Donata Konopacka-Łyskawa ◽  
Natalia Czaplicka ◽  
Barbara Kościelska ◽  
Marcin Łapiński ◽  
Jacek Gębicki
Keyword(s):  
Calcium Carbonate ◽  
Biomedical Applications ◽  
Xrd Analysis ◽  
Polymorphic Form ◽  
Co2 Absorption ◽  
X Ray Diffraction ◽  
Precipitated Calcium Carbonate ◽  
X Ray ◽  
Living Organisms ◽  
Polymorphic Composition

Calcium carbonate is a compound existing in living organisms and produced for many biomedical applications. In this work, calcium carbonate was synthesized by a CO2 bubbling method using ammonia as a CO2 absorption promotor. Glucose, fructose, sucrose, and trehalose were added into the reaction mixture to modify characteristics of precipitated calcium carbonate particles. To determine the polymorphic form of produced calcium carbonate particles, Fourier transform infrared spectroscopy (FTIR-ATR) and X-ray diffraction (XRD) analysis were performed. Scanning electron microscopy (SEM) was used to estimate the size and shape of produced particles. Mixtures of vaterite and calcite were synthesized in all experiments. The percentage content of the vaterite in the samples depended on used additive. The highest concentration of vaterite (90%) was produced from a solution containing sucrose, while the lowest concentration (2%) was when fructose was added. Saccharides affected the rate of CO2 absorption, which resulted in a change in the precipitation rate and, therefore, the polymorphic composition of calcium carbonate obtained in the presence of saccharides was more varied.

Microstructural Characterization of Glass-to-Metal Brazed Joint

2012 ◽  
Vol 616-618 ◽  
pp. 1732-1735 ◽  
Author(s):  
Xi Hai Shen ◽  
Yu Gang Zheng ◽  
Liang Chang ◽  
Jin Jia Guo ◽  
Song Bin Ye ◽  
...  
Keyword(s):  
Thermal Power ◽  
Microstructural Characterization ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Solar Thermal Power ◽  
Brazed Joints ◽  
Brazed Joint ◽  
Scanning Electron

Aiming at the glass-to-metal seals serving in the Solar Thermal Power (STP), glass-to-metal vacuum brazed joints were studied. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis were performed to examine the microstructure and element contents of interface seam on the glass-to-metal vacuum brazed joints. Also, the compositional concentration of the interface seam was measured by using energy dispersive spectroscopy (EDS).

Sign in / Sign up

Export Citation Format

Share Document