Probing the molecular weights of sweetgum and pine kraft lignin fractions

TAPPI Journal ◽  
2021 ◽  
Vol 20 (6) ◽  
pp. 381-391
Author(s):  
JULIANA M. JARDIM ◽  
PETER W. HART ◽  
LUCIAN LUCIA ◽  
HASAN JAMEEL
Keyword(s):  
Molecular Weight ◽  
Black Liquor ◽  
Average Molecular Weight ◽  
Gel Permeation Chromatography ◽  
Systematic Investigation ◽  
Kraft Pulping ◽  
Molecular Weights ◽  
Lignin Recovery ◽  
Lignin Reactivity ◽  
Kinetics Of

The present investigation undertook a systematic investigation of the molecular weight (MW) of kraft lignins throughout the pulping process to establish a correlation between MW and lignin recovery at different extents of the kraft pulping process. The evaluation of MW is crucial for lignin characterization and utilization, since it is known to influence the kinetics of lignin reactivity and its resultant physicochemical properties. Sweetgum and pine lignins precipitated from black liquor at different pHs (9.5 and 2.5) and different extents of kraft pulping (30–150 min) were the subject of this effort. Gel permeation chromatography (GPC) was used to deter- mine the number average molecular weight (Mn), mass average molecular weight (Mw), and polydispersity of the lignin samples. It was shown that the MW of lignins from both feedstocks follow gel degradation theory; that is, at the onset of the kraft pulping process low molecular weightlignins were obtained, and as pulping progressed, the molecular weight peaked and subsequently decreased. An important finding was that acetobromination was shown to be a more effective derivatization technique for carbohydrates containing lignins than acetylation, the technique typically used for derivatization of lignin.

Article

1998 ◽  
Vol 76 (11) ◽  
pp. 1699-1706 ◽  
Author(s):  
Jonathan Z Knaul ◽  
Mohammad R Kasaai ◽  
V Tam Bui ◽  
Katherine AM Creber
Keyword(s):  
Molecular Weight ◽  
Average Molecular Weight ◽  
Gel Permeation Chromatography ◽  
Solvent System ◽  
Similar Degree ◽  
Degree Of Deacetylation ◽  
Molecular Weights ◽  
Good Accord ◽  
Gel Permeation ◽  
Weight Analysis

Starting from a chitosan sample with a degree of deacetylation of 71%, three separate sample sets were generated by successive deacetylation and reacetylation processes. The degree of deacetylation of samples was determined by UV spectrometry supported by thermogravimetric analysis. The molecular weight of chitosan samples was determined in a solvent system of 0.25 M CH3COOH/0.25 M CH3COONa, using viscometry and gel permeation chromatography (GPC) with a TSK-gel column. The first set of samples had a similar degree of deacetylation (DDA) but differing molecular weights. The second set of samples had a similar molecular weight but differing degrees of deacetylation. The Mark-Houwink-Sakurada constants used for the determination of viscosity average molecular weight and the universal calibration of the GPC system were K = 1.40 × 10-4 dL/g and a = 0.83. Results showed that molecular weights determined from both techniques are in good accord only at lower degrees of deacetylation. This may be attributed to the fact that the chemical structure of chitosan samples could have been largely altered with increasing or decreasing degree of deacetylation. Nevertheless, the trend with which the molecular weights vary with the deacetylation time is consistent over a limited DDA range. A literature review of molecular weight analysis of chitosan is included.Key words: chitosan, degree of deacetylation, gel permeation chromatography, molecular weight, viscometry.

scholarly journals The Application of Organic Phosphate Nucleating Agents in Polypropylene with Different Molecular Weights

Crystals ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1543
Author(s):  
Juan Li ◽  
Zhaohua Liang ◽  
Chengtao Gao ◽  
Shanshan Luo ◽  
Shaowen Huang ◽  
...  
Keyword(s):  
Molecular Weight ◽  
Average Molecular Weight ◽  
Gel Permeation Chromatography ◽  
Nucleating Agent ◽  
Organic Phosphate ◽  
Nucleating Agents ◽  
Tem Analysis ◽  
Molecular Weights ◽  
Dispersed Particles ◽  
Extrusion Method

Two kinds of organic phosphate nucleating agent (NA-11 and NA-21) were used in PP with different molecular weights through the melt extrusion method. The dispersibility of the nucleating agents in PP, and the effect of the nucleating agents on the molecular weight, rheological behavior and crystallization behavior of PP were investigated. SEM and TEM analysis showed that the average radius of the dispersed particles (nucleating agents) was larger in LPP than that in HPP. The good dispersion of NA-21 also created more nucleation embryos for the adsorption of polypropylene molecules than the agglomerated NA-11. The gel permeation chromatography (GPC) analysis showed that the average molecular weight of HPP and LPP both decreased with the addition of a nucleating agent. The rotational rheometer and capillary rheometer analysis showed that the effect of NA-21 on reducing intermolecular entanglement was more significant, whether in HPP or LPP. The addition of NA-21 had less elastic energy storage and better flow stability, and could be processed at a higher speed. Simultaneously, the relaxation time in the blends with LPP was shorter than that with HPP. It was found that the crystallinity and nucleation efficiency of HPP/nucleating agent blends increased remarkably, while there was a barely perceptible increase in LPP/nucleating agent blends.

scholarly journals Intrinsic Viscosity-molecular Weight Relationship of Poly (Hexanediol Adipate)

2019 ◽  
pp. 1-8
Author(s):  
Jiankun Li ◽  
Zegang Zong ◽  
Dehua Hou ◽  
Bojun Tu ◽  
Weilan Xue ◽  
...  
Keyword(s):  
Molecular Weight ◽  
Intrinsic Viscosity ◽  
Average Molecular Weight ◽  
Group Analysis ◽  
Gel Permeation Chromatography ◽  
Molecular Weights ◽  
The One ◽  
Relationship Of ◽  
The Relationship ◽  
End Group

In this work, a series of poly(Hexanediol adipate)(PHA) samples (103＜Mn＜104) with narrow molecular weight distribution were prepared by the polymerization between adilic acid and 1,6-hexandiol. End-group analysis was applied to determine the number average molecular weight (Mn) of PHA. Gel permeation chromatography (GPC) was employed to obtain the average molecular weights (Mn, Mv, Mw).The intrinsic viscosity of the samples in the tetrahydrofuran (THF) solution was determined at 298 K by the dilution extrapolation method and the one-point method. The relationship between the intrinsic viscosity and the molecular weight for PHA was studied by the Mark-Houwink-Sakurada (MHS) equation, and the parameters of equation were determined.

scholarly journals Study on Preparation of Water-Soluble Chitosan with Varying Molecular Weights and Its Antioxidant Activity

2019 ◽  
Vol 2019 ◽  
pp. 1-8 ◽  
Author(s):  
Dang Xuan Du ◽  
Bui Xuan Vuong
Keyword(s):  
Molecular Weight ◽  
Antioxidant Activity ◽  
Dose Range ◽  
Average Molecular Weight ◽  
Gel Permeation Chromatography ◽  
Chitosan Solution ◽  
Water Soluble ◽  
Molecular Weights ◽  
Ph Level ◽  
The One

The preparation of water-soluble chitosan (WSC) with various molecular weights by gamma Co-60 irradiation of chitosan solution (5%) in the presence of hydrogen peroxide (1%) combined with acetylated reaction was carried out. The average molecular weight (Mw) of chitosan was measured by gel permeation chromatography (GPC). The chemical structure and the crystallinity of chitosan and WSC were characterized by Fourier-transform infrared (FT-IR) spectroscopy and X-ray diffraction (XRD), respectively. The antioxidant activity of WSC and chitosan was investigated using the free radical 2,2′-azino-bis (3-ethylbenzothiazoline-6-sulphonic acid) (ABTS•+). Obtained results showed that chitosan with Mw of 18–90 kDa could be efficiently prepared by this technique in the dose range from 10 to 24.5 kGy. After the acetylated process, the resulting WSC possesses good solubility in a wide pH level of 2–12, and WSC with low molecular weight exhibited significantly higher antioxidant activity than the one with high molecular weight. In detail, the antioxidant activity was 14.7%, 70.5%, 84.2%, 89.4%, and 97.5% for WSC samples prepared from chitosan with Mw of 140.2 kDa, 91.4 kDa, 51.2 kDa, 35.3 kDa, and 18.1 kDa, respectively, at the same reaction time of 90 min. Moreover, the antioxidant activity of WSC was higher than that of chitosan. Thus, WSC prepared by gamma Co-60 irradiation and acetylated process can be potentially applied as a natural antioxidant agent.

scholarly journals Use of Rubber Process Analyzer for Characterizing the Molecular Weight Parameters of Natural Rubber

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Tianming Gao ◽  
Ruihong Xie ◽  
Linghong Zhang ◽  
Hongxing Gui ◽  
Maofang Huang
Keyword(s):  
Molecular Weight ◽  
Natural Rubber ◽  
Milling Time ◽  
Laser Light ◽  
Average Molecular Weight ◽  
Gel Permeation Chromatography ◽  
Sweep Frequency ◽  
Weight Average Molecular Weight ◽  
Molecular Weights ◽  
Strain Sweep

The aim of this work is to introduce a simple and rapid method for characterizing the molecular weight parameters and other molecular structure parameters of natural rubber (NR) using a rubber process analyzer (RPA). In this work, NR of different molecular weights was prepared by milling. Molecular weight parameters were measured by gel permeation chromatography coupled with laser light scattering (GPC-LLS) for comparison with RPA results. It was verified that increasing of milling time leads to a decrease of the number-average molecular weight (M-n), weight-average molecular weight (M-w), and molecular weight distribution (MWD). The dynamic and rheological properties were evaluated on RPA by tests of strain sweep, frequency sweep, and stress relaxation. These results were used to characterize the average molecular weight, MWD, and viscosity of NR and were found to agree with those from GPC-LLS. This convenient and rapid technology for characterizing NR molecular weight parameters would be especially useful in the elastomer industry.

scholarly journals Investigating Lignin-Derived Monomers and Oligomers in Low-Molecular-Weight Fractions Separated from Depolymerized Black Liquor Retentate by Membrane Filtration

Molecules ◽  
2021 ◽  
Vol 26 (10) ◽  
pp. 2887
Author(s):  
Kena Li ◽  
Jens Prothmann ◽  
Margareta Sandahl ◽  
Sara Blomberg ◽  
Charlotta Turner ◽  
...  
Keyword(s):  
Molecular Weight ◽  
High Performance ◽  
Membrane Filtration ◽  
Black Liquor ◽  
Complex Mixture ◽  
Value Added ◽  
Kraft Pulping ◽  
Classification Model ◽  
Low Molecular Weight ◽  
Chemical Complexity

Base-catalyzed depolymerization of black liquor retentate (BLR) from the kraft pulping process, followed by ultrafiltration, has been suggested as a means of obtaining low-molecular-weight (LMW) compounds. The chemical complexity of BLR, which consists of a mixture of softwood and hardwood lignin that has undergone several kinds of treatment, leads to a complex mixture of LMW compounds, making the separation of components for the formation of value-added chemicals more difficult. Identifying the phenolic compounds in the LMW fractions obtained under different depolymerization conditions is essential for the upgrading process. In this study, a state-of-the-art nontargeted analysis method using ultra-high-performance supercritical fluid chromatography coupled to high-resolution multiple-stage tandem mass spectrometry (UHPSFC/HRMSn) combined with a Kendrick mass defect-based classification model was applied to analyze the monomers and oligomers in the LMW fractions separated from BLR samples depolymerized at 170–210 °C. The most common phenolic compound types were dimers, followed by monomers. A second round of depolymerization yielded low amounts of monomers and dimers, while a high number of trimers were formed, thought to be the result of repolymerization.

scholarly journals Characterisation of Sequential Solvent Fractionation and Base-catalysed Depolymerisation of Treated Alkali Lignin

BioResources ◽  
2015 ◽  
Vol 10 (3) ◽  
pp. 4137-4151 ◽  
Author(s):  
Aikfei Ang ◽  
Zaidon Ashaari ◽  
Edi Suhaimi Bakar ◽  
Nor Azowa Ibrahim
Keyword(s):  
Molecular Weight ◽  
Chemical Structure ◽  
Average Molecular Weight ◽  
Gel Permeation Chromatography ◽  
Solubility Parameters ◽  
Low Molecular Weight ◽  
Sequential Fractionation ◽  
Weight Average Molecular Weight ◽  
Solvent Fractionation ◽  
Alkali Lignin

An alkali lignin (OL) with a weight-average molecular weight (Mw) of 11646 g/mol was used to prepare low-molecular weight lignin for resin synthesis. The low-molecular weight lignin feedstock was obtained via base-catalysed depolymerisation (BCD) treatments at different combined severity factors. Sequential fractionation of the OL and BCD-treated lignins using organic solvents with different Hildebrand solubility parameters were used to alter the homogeneity of the OL. The yield and properties of OL itself and OL and BCD-treated OL dissolved in propan-1-ol (F1), ethanol (F2), and methanol (F3) were determined. Regardless of the treatment applied, a small amount of OL was dissolved in F1 and F2. The BCD treatment did not increase the yield of F1 but did increase the yields of F2 and F3. Gel permeation chromatography (GPC) showed that the repolymerization reaction occurred in F3 for all BCD-treated OL, so these lignins were not suitable for use as feedstocks for resin production. The GPC, 13Carbon-nuclear magnetic resonance, and Fourier transform infrared spectroscopy analyses confirmed that the F3 in OL exhibited the optimum yield, molecular weight distribution, and chemical structure suitable for use as feedstocks for resin synthesis.

Isoprene and Rubber. Part 29. High Molecular Hydrorubbers

1932 ◽  
Vol 5 (2) ◽  
pp. 136-140
Author(s):  
H. Staudinger ◽  
W. Feisst
Keyword(s):  
Molecular Weight ◽  
Catalytic Reduction ◽  
Molecular Form ◽  
Average Molecular Weight ◽  
Molecular Size ◽  
Decomposition Products ◽  
Molecular Weights ◽  
Rubber Part ◽  
Derivatives Of ◽  
Suitable Process

Abstract The molecular concept in organic chemistry is based upon the fact that the molecules, whose existence is proved by vapor density determinations, enter into chemical reactions as the smallest particles. If now it is assumed that organic molecular colloids like rubber are dissolved in dilute solution in molecular form then it must be proved that in the chemical transposition of macromolecules as well no change in the size of the macromolecules occurs. In the case of hemicolloids, therefore for molecular colloids with an average molecular weight of 1000 to 10,000, this has been proved by the reduction of polyindenes, especially of polysterenes, to hydroproducts with the same average molecular weight, and also by the fact that cyclorubbers do not change their molecular weight upon autoöxidation. The molecular weights of hemi-colloidal hydrocarbons are therefore invariable. This is much more difficult to prove in the case of rubber, although there are many more ways in which unsaturated rubber can be transposed than the stable polysterenes, polyindenes, and poly cyclorubbers. In most of the reactions with rubber, as in its action with nitrosobenzene, oxidizing agents, hydrogen halides, and halogens, an extensive decomposition takes place as a result of the instability of the molecule, which is referred to in another work. Therefore derivatives of rubber are not formed, but derivatives of hemi-colloidal decomposition products. The catalytic reduction of rubber in the cold appears to be the most suitable process of making it react without changing its molecular size in order to prove that in a chemical transposition its molecular weight remains the same.

SIZE, STABILITY, AND HETEROGENEITY OF APURINIC ACID

1956 ◽  
Vol 34 (6) ◽  
pp. 1107-1117 ◽  
Author(s):  
G. C. Wood ◽  
David B. Smith
Keyword(s):  
Molecular Weight ◽  
Nucleic Acid ◽  
Acid Treatment ◽  
Average Molecular Weight ◽  
Weight Average Molecular Weight ◽  
Molecular Weights ◽  
Size Stability ◽  
Mild Acid

Apurinic acid prepared by mild acid treatment of sodium desoxyribonucleate and of fractions of sodium desoxyribonucleate was sufficiently stable to permit estimations of molecular weight and polydispersity. Apurinic acid from unfractionated desoxyribonucleate had a weight-average molecular weight of 25,000 and was very polydisperse. Preparations from fractionated desoxyribonucleate representing about half the original nucleic acid were much less polydisperse and had molecular weights of about 10,000.

scholarly journals Methylene-Bridged Tridentate Salicylaldiminato Binuclear Titanium Complexes as Copolymerization Catalysts for the Preparation of LLDPE through [Fe]/[Ti] Tandem Catalysis

Polymers ◽  
2019 ◽  
Vol 11 (7) ◽  
pp. 1114 ◽  
Author(s):  
Yani Luo ◽  
Jian Li ◽  
Derong Luo ◽  
Qingliang You ◽  
Zifeng Yang ◽  
...  
Keyword(s):  
Molecular Weight ◽  
High Temperature ◽  
Gel Permeation Chromatography ◽  
13C Nmr Spectroscopy ◽  
Molar Ratio ◽  
Tandem Catalysis ◽  
Titanium Complexes ◽  
Scanning Calorimetry ◽  
Molecular Weights ◽  
Branching Degree

A novel tandem catalysis system consisted of salicylaldiminato binuclear/mononuclear titanium and 2,6-bis(imino)pyridyl iron complexes was developed to catalyze ethylene in-situ copolymerization. Linear low-density polyethylene (LLDPE) with varying molecular weight and branching degree was successfully prepared with ethylene as the sole monomer feed. The polymerization conditions, including the reaction temperature, the Fi/Ti molar ratio, and the structures of bi- or mononuclear Ti complexes were found to greatly influence the catalytic performances and the properties of obtained polymers. The polymers were characterized by differential scanning calorimetry (DSC), high temperature gel permeation chromatography (GPC) and high temperature 13C NMR spectroscopy, and found to contain ethyl, butyl, as well as some longer branches. The binuclear titanium complexes demonstrated excellent catalytic activity (up to 8.95 × 106 g/molTi·h·atm) and showed a strong positive comonomer effect when combined with the bisiminopyridyl Fe complex. The branching degree can be tuned from 2.53 to 22.89/1000C by changing the reaction conditions or using different copolymerization pre-catalysts. The melting points, crystallinity and molecular weights of the products can also be modified accordingly. The binuclear complex Ti2L1 with methylthio sidearm showed higher capability for comonomer incorporation and produced polymers with higher branching degree and much higher molecular weight compared with the mononuclear analogue.

Sign in / Sign up

Export Citation Format

Share Document