scholarly journals Influence of Polymeric Coating the Aggregate Surface on Moisture Damage of Hot Mix Asphalt

2020 ◽  
Author(s):  
Mojtaba Khodadadi ◽  
Alireza Azarhoosh ◽  
Ali Khodaii
Keyword(s):  
Tensile Strength ◽  
Polyethylene Terephthalate ◽  
Hot Mix Asphalt ◽  
Resilient Modulus ◽  
Asphalt Binder ◽  
Moisture Damage ◽  
Indirect Tensile Strength ◽  
Polymeric Coating ◽  
Moisture Susceptibility ◽  
Indirect Tensile

Moisture damage is one of the common causes of asphalt pavement failure in moisture presence. One of the convenient approaches to decreasing moisture sensitivity in hot-mix asphalt is coating the aggregate surface with a suitable agent. In this study, the effects of polyethylene terephthalate on moisture damage of asphalt mixtures were evaluated by applying indirect tensile strength and resilient modulus tests. The asphalt specimens were prepared with two types of aggregates (granite and limestone) and neat asphalt binder of 60/70 penetration grade. The results showed that the ratio of wet/dry values of indirect tensile strength and resilient modulus for mixtures containing limestone was higher than those of the samples with granite aggregate. Furthermore, the results of the laboratory tests indicate that polyethylene terephthalate improves resistance to moisture susceptibility. Because polyethylene terephthalate increases the wettability of asphalt binder over the aggregate and the adhesion between the asphalt binder and aggregate, especially in the mixtures containing acidic (granite) aggregate prone to moisture damage.

scholarly journals Evaluations of Nano-Sized Hydrated Lime on the Moisture Susceptibility of Hot Mix Asphalt Mixtures

2012 ◽  
Vol 174-177 ◽  
pp. 82-90 ◽  
Author(s):  
Ju Nan Shen ◽  
Zhao Xing Xie ◽  
Fei Peng Xiao ◽  
Wen Zhong Fan
Keyword(s):  
Tensile Strength ◽  
Experimental Design ◽  
Hot Mix Asphalt ◽  
Hydrated Lime ◽  
Asphalt Mixtures ◽  
Indirect Tensile Strength ◽  
Moisture Resistance ◽  
Strength Ratio ◽  
Moisture Susceptibility ◽  
Indirect Tensile

The objective of this study was to evaluate the effect of nano-sized hydrated lime on the moisture susceptibility of the hot mix asphalt (HMA) mixtures in terms of three methodologies to introduce into the mixtures. The experimental design for this study included the utilizations of one binder source (PG 64-22), three aggregate sources and three different methods introducing the lime. A total of 12 types of HMA mixtures and 72 specimens were fabricated and tested in this study. The performed properties include indirect tensile strength (ITS), tensile strength ratio (TSR), flow, and toughness. The results indicated that the nano-sized lime exhibits better moisture resistance. Introducing process of the nano-sized lime will produce difference in moisture susceptibility.

Comparison of Coarse Matrix High Binder and Dense-Graded Hot-Mix Asphalt

1997 ◽  
Vol 1590 (1) ◽  
pp. 108-117 ◽  
Author(s):  
Richard P. Izzo ◽  
Joe W. Button ◽  
Maghsoud Tahmoressi
Keyword(s):  
Tensile Strength ◽  
Creep Test ◽  
Resilient Modulus ◽  
Permanent Deformation ◽  
Asphalt Binder ◽  
Moisture Damage ◽  
Static Creep ◽  
Indirect Tensile ◽  
Effects Of Aging ◽  
Static Creep Test

Coarse matrix high binder (CMHB) is a gap-graded hot mix consisting of a large proportion of coarse aggregate with an asphalt binder-filler mastic. CMHB and dense-graded mixtures were compared in terms of their resistance to rutting (permanent deformation), moisture damage, aging, and water permeability. A static creep test was performed to evaluate relative rutting susceptibility. Moisture damage was assessed with the tensile strength ratio (TSR) and a boiling-water test. The effects of aging were evaluated with indirect tensile strength and resilient modulus testing. Penetration and complex shear modulus ( G*) of the recovered, aged asphalt were measured. Permeability was determined with Darcy's Law for flow through saturated, porous media. The static creep test did not indicate that CMHB mixtures were consistently more resistant to rutting in comparison with dense-graded mixtures. CMHB mixtures were found to be more resistant to moisture damage, which was indicated by higher TSR values and less visible stripping than corresponding dense-graded mixtures. The dense-graded mixtures exhibited higher resilient moduli and indirect tensile strengths after short-term and long-term aging. Penetration of binder extracted from aged CMHB mixtures was greater than that from dense-graded mixtures. Binder extracted from aged dense-graded mixtures exhibited higher G* values. The permeability of CMHB mixtures was greater than that of the dense-graded mixtures with comparable air voids.

Evaluation of Moisture and Ageing Effects on Calcium Carbonite Nanoparticles Modified Asphalt Mixtures

2018 ◽  
Vol 34 ◽  
pp. 40-47 ◽  
Author(s):  
Shaban Ismael Albrka Ali ◽  
Riyadh Abdulwahid ◽  
Muhamed Laith Eidan ◽  
Nur Izzi Md Yusoff
Keyword(s):  
Tensile Strength ◽  
Dynamic Modulus ◽  
Resilient Modulus ◽  
Asphalt Mixture ◽  
Indirect Tensile Strength ◽  
Traffic Load ◽  
Moisture Susceptibility ◽  
Modified Asphalt ◽  
Dynamic Modulus Test ◽  
Indirect Tensile

Flexible pavements deteriorate and crack with time due to the frequent traffic load imposed upon it. Many studies have been done to predict the effects of frequent traffic load and environmental conditions on pavements in the effort to find the best pavement design which resist deterioration and ensure longer pavement service time. This study investigates the effect of mixing asphalt with varying percentages of nano calcium carbonate (CaCO3), namely 0, 2, 4, and 6 %. The mixtures were designed based on the Superpave mix design criteria. Investigation was done using several tests, namely resilient modulus, indirect tensile strength, moisture susceptibility, and dynamic modulus tests. Samples were subjected to aging to determine their resilient modulus. The results of the investigation show that resilient modulus and indirect tensile strength increased when higher percentages of nanoparticles were added to asphalt mixture, with improvement of 138 and 48.18% respectively. Modified binders showed up to 17% improvement in moisture susceptibility comparison to base asphalt mixture, while the result of dynamic modulus test showed that the stiffness of modified asphalt increased 76.69%. The investigation also found that adding 6% CaCO3 nanoparticles to asphalt produced modified asphalt with the best performance. In addition, the results show that the modified asphalt with CaCO3 is suitable for hot and humid regions (tropical countries) in the field of highways construction, as the modifier was able to mitigate the influences of high-temperature rutting and moisture damage.

The Influence of Coconut Shell as Coarse Aggregates in Asphalt Mixture

2016 ◽  
Vol 700 ◽  
pp. 227-237 ◽  
Author(s):  
Siti Nur Amiera Jeffry ◽  
Ramadhansyah Putra Jaya ◽  
Norhafizah Manap ◽  
Nurfatin Aqeela Miron ◽  
Norhidayah Abdul Hassan
Keyword(s):  
Tensile Strength ◽  
Asphalt Concrete ◽  
Resilient Modulus ◽  
Asphalt Mixture ◽  
Indirect Tensile Strength ◽  
Coconut Shell ◽  
Engineering Properties ◽  
Modified Bitumen ◽  
Coarse Aggregates ◽  
Indirect Tensile

Significant quantities of coconut shell (CS), a by-product of agriculture, can be used as an artificial source of coarse aggregates. In this study, four CSs were used as coarse aggregates replacement in asphalt concrete with 0%, 10%, 20%, 30%, and 40% weight volumes. The particle sizes of the CSs used as main coarse aggregates range from 5 mm to 20 mm. The Marshall Stability test shows that the optimum bitumen content for asphalt mixtures is 5.1%. The engineering properties investigated include the volumetric, dynamic creep, indirect tensile strength, and resilient modulus. Test results show that stability decreases with increasing CS content because of high water absorption. Considering that CSs absorb bitumen, a further detailed investigation is needed to assess the performance of modified bitumen on mixture. Furthermore, the use of CSs as coarse aggregates in asphalt concrete help increase the resilient modulus, stiffness, and indirect tensile strength up to 30%. Generally, a 10% replacement of coarse aggregates with CSs is the optimal limit.

scholarly journals EVALUATION OF THE PERFORMANCE OF WASTE MARBLE DUST AS A MINERAL FILLER IN HOT-MIX ASPHALT CONCRETE

2021 ◽  
Vol 12 (1) ◽  
pp. 1-14
Author(s):  
Levy Sang ◽  
Temitope Idowu ◽  
Victoria Okumu
Keyword(s):  
Tensile Strength ◽  
Hot Mix Asphalt ◽  
Indirect Tensile Strength ◽  
Engineering Properties ◽  
Sustainable Construction ◽  
Mineral Filler ◽  
Marble Dust ◽  
Indirect Tensile ◽  
Expanding Population ◽  
Marshall Stability

As the construction industry continues to evolve globally, there is a need to develop best practices geared towards achieving sustainable construction. Asphalt concrete’s demand has been increasing steadily with an estimated global demand of 122.5 million tons in 2019. This is driven primarily by the growth in construction activities in developing countries as each country works towards enhancing its transportation facilities to cater to the ever-expanding population. Hence, there are needs to develop newer and more efficient means of asphalt consumption. One of such is identifying cheaper or waste materials for use in Asphalt production. This study, therefore, examined the viability of waste marble dust (WMD), an industrial waste produced during the shaping and polishing of marble blocks and also during its extraction from the mines, as a mineral filler in Hot-mix asphalt (HMA) concrete. Engineering properties such as Marshall stability and flow, Void characteristics, Indirect tensile strength and Tensile strength ratio properties were examined. It was observed that the addition of WMD steadily increased the Marshall Stability and indirect tensile strength values and lowered the voids percentages. The study’s major finding is that waste marble dust is highly suitable as a mineral filler in HMA and a 3% by volume addition of WMD in HMA at 4.5% binder content produced the most optimal mix for use in road pavements.

Effect of Modified Asphalt Cement of the Performance of Stone Matrix Mixtures

2020 ◽  
Vol 38 (5A) ◽  
pp. 789-800
Author(s):  
Duaa A. Khalaf ◽  
Zaynab I. Qasim ◽  
Karim H. Al Helo
Keyword(s):  
Tensile Strength ◽  
Fracture Resistance ◽  
Laboratory Tests ◽  
Asphalt Binder ◽  
Asphalt Mixtures ◽  
Indirect Tensile Strength ◽  
Asphalt Cement ◽  
Indirect Tensile ◽  
Marshall Stability ◽  
Stone Matrix

This research investigates the behavior of Stone Matrix Asphalt mixtures (SMA) modified with styrene-butadiene-styrene (SBS) polymer at four percentages (1, 2, 3 and 4%) by weight of asphalt cement. The moisture susceptibility and rutting were taken into consideration in this study. To achieve the objective of this research the superpave system is conducted to design the asphalt mixtures. The physical properties of aggregate, bitumen and other mix materials were assessed and evaluated with the laboratory tests. The mixtures were prepared using penetration Graded (40-50) bitumen and a chemical named Polypropylene Fibers was used as a stabilizing additive. Fibers have been used in SMA mixtures for two main reasons: To increase the toughness and fracture resistance of hot mix asphalt (HMA) and to act as a stabilizer to prevent drain down of the asphalt binder. The laboratory tests include indirect tensile strength test, Marshall stability and retained Marshall Stability test (RMS). For rutting test the Roller wheel compactor is used for preparing the asphaltic samples and Wheel tracking device is used to evaluate the rutting of asphaltic slabs. The results showed that the SBS polymer asphalt mixture gave better moisture sensitivity and better fracture resistance according to the study.It is noted that indirect tensile strength ratio (TSR) increases by 93.1 % and the rut depth decreases by 32.5 % when adding 3% SBS polymer to SMA.

Laboratory Performance Evaluation of Cement-Stabilized Soil Base Mixtures

2000 ◽  
Vol 1721 (1) ◽  
pp. 19-28 ◽  
Author(s):  
Louay N. Mohammad ◽  
Amar Raghavandra ◽  
Baoshan Huang
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Resilient Modulus ◽  
Flexible Pavements ◽  
Indirect Tensile Strength ◽  
Treated Soil ◽  
Stabilized Soil ◽  
Indirect Tensile ◽  
Soil Mixtures

In-place cement-stabilized soils have served as the primary base material for the majority of noninterstate flexible pavements in Louisiana for many years. These materials are economically and easily constructed and provide outstanding structural characteristics for flexible pavements. However, these cement-treated materials crack due to shrinkage, with the cracks reflecting from the base to the surface. A laboratory study examined the performance of four different cement-stabilized soil mixtures recently used in the construction of test lanes at the Louisiana Pavement Testing Facilities. Laboratory tests included the indirect tensile strength and strain, unconfined compressive strength, and indirect tensile resilient modulus tests. The four mixtures were ( a) in-place-mixed cement-treated soil with 10 percent cement, ( b) plant-mixed cement-treated soil with 10 percent cement, ( c) plant-mixed cement-treated soil with 4 percent cement, and ( d) plant-mixed cement-treated soil with 4 percent cement and fiber reinforcement. The results indicated that there was no significant difference in performance between the plant-mixed and in-place-mixed cement-treated soil mixtures. The inclusion of fiber to the cement-treated soil mixture significantly increased the indirect tensile strain and the toughness index. Increases in compaction effort maintained or significantly increased the indirect tensile strength and unconfined compressive strength. Increases in curing period maintained or significantly increased indirect tensile and unconfined compressive strength as well as the resilient modulus of the mixtures.

scholarly journals Reinforcement of Recycled Foamed Asphalt Using Short Polypropylene Fibers

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
Yongjoo Kim ◽  
Tae-Soon Park
Keyword(s):  
Tensile Strength ◽  
Asphalt Binder ◽  
Indirect Tensile Strength ◽  
Polypropylene Fibers ◽  
Foamed Asphalt ◽  
Wheel Tracking Test ◽  
Indirect Tensile ◽  
Reinforcing Effects ◽  
Marshall Stability ◽  
Wheel Tracking

This paper presents the reinforcing effects of the inclusion of short polypropylene fibers on recycled foamed asphalt (RFA) mixture. Short polypropylene fibers of 10 mm length with a 0.15% by weight mixing ratio of the fiber to the asphalt binder were used. The Marshall stability test, the indirect tensile strength test, the resilient modulus test, and wheel tracking test of the RFA mixtures were conducted. The test results were compared to find out the reinforcing effects of the inclusion of the fiber and the other mixtures, which included the conventional recycled foamed asphalt (RFA) mixtures; the cement reinforced recycled foamed asphalt (CRFA) mixtures; the semihot recycled foamed asphalt (SRFA) mixtures; and recycled hot-mix asphalt (RHMA) mixtures. It is found that the FRFA mixture shows higher Marshall stability than the RFA and SRFA mixtures, higher indirect tensile strength than the RFA mixture, and higher rut resistance than the RFA, SRFA, and RHMA mixtures as seen from the wheel tracking test.

scholarly journals The effect of different deicing solutions on the moisture susceptibility of asphalt mixture

2021 ◽  
Vol 3 (6) ◽  
Author(s):  
Ali Abdi Kordani ◽  
Seyed Hani Seifi ◽  
Hossein Ghasemzadeh Tehrani ◽  
Bahram Shirini
Keyword(s):  
Tensile Strength ◽  
Sodium Chloride ◽  
Magnesium Chloride ◽  
Asphalt Pavement ◽  
Potassium Acetate ◽  
Indirect Tensile Strength ◽  
List Type ◽  
Moisture Susceptibility ◽  
Asphalt Mix ◽  
Indirect Tensile

Abstract The present research studies the effectiveness and efficiency of solutions such as sodium chloride, magnesium chloride and potassium acetate on asphalt pavement to reduce the damage caused by moisture on asphalt pavement in winter. To prevent the stripping problem in asphalt, Nano-Zycotherm with three quantities corresponding to 0.1%, 0.2% and 0.3% weight of bitumen is used in this study. Under the saturated condition with the above solutions, the indirect tensile test performs by applying a freeze–thaw cycle as a means to measure the amount of moisture susceptibility. The results indicate that the asphalt mix containing 0.3% Nano-Zycotherm has a higher indirect tensile strength and tensile strength ratio than asphalt mix containing 0.1% and 0.2% Nano-Zycotherm. Accordingly, Magnesium chloride solution is the most effective deicing material to improve the indirect tensile strength and durability of asphalt pavements when faced with moisture and ice. Article highlights The presence of Nano-Zycotherm in asphalt leads to its increased resistance against stripping. The use of Sodium chloride and potassium acetate deicing solutions causes some damages in asphalt. Considering different solutions, magnesium chloride has the best performance against asphalt stripping.

Use of steel slag aggregate in asphalt concrete mixes

2007 ◽  
Vol 34 (8) ◽  
pp. 902-911 ◽  
Author(s):  
Ibrahim M Asi ◽  
Hisham Y Qasrawi ◽  
Faisal I Shalabi
Keyword(s):  
Tensile Strength ◽  
Asphalt Concrete ◽  
Coarse Aggregate ◽  
Resilient Modulus ◽  
Steel Slag ◽  
Indirect Tensile Strength ◽  
Engineering Properties ◽  
Optimal Replacement ◽  
Indirect Tensile ◽  
Creep Modulus

There are three major steel-manufacturing factories in Jordan. All of their by-product, steel slag, is dumped randomly in open areas, causing many environmentally hazardous problems. This research was intended to study the effectiveness of using steel slag aggregate (SSA) in improving the engineering properties of locally produced asphalt concrete (AC) mixes. The research started by evaluating the toxicity and chemical and physical properties of the steel slag. Then 0%, 25%, 50%, 75%, and 100% of the limestone coarse aggregate in the AC mixes was replaced by SSA. The effectiveness of the SSA was judged by the improvement in indirect tensile strength, resilient modulus, rutting resistance, fatigue life, creep modulus, and stripping resistance of the AC samples. It was found that replacing up to 75% of the limestone coarse aggregate by SSA improved the mechanical properties of the AC mixes. The results also showed that the 25% replacement was the optimal replacement level. Key words: steel slag aggregate, asphalt concrete, Superpave, indirect tensile strength, fatigue, rutting, creep.

Sign in / Sign up

Export Citation Format

Share Document