scholarly journals Simulating the Speed control System of Wind Turbines Using MATLAB Software

2020 ◽  
Vol 4 (2) ◽  
pp. 1-6
Author(s):  
Seyed Mojtaba Hosseini Bafoghi ◽  
Hamidreza Khezri
Keyword(s):  
Mathematical Model ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Pid Controller ◽  
Electrical Energy ◽  
Induction Generator ◽  
Rotor Speed ◽  
Output Frequency ◽  
Static Loads ◽  
Simulation Results

In this paper, a mathematical method is proposed to control the output frequency of a self-excited induction generator using wind turbines and static loads. A dynamic model of the wind turbine is implemented to model the Connections and fittings of the wind turbine to convert the wing energy to electrical energy. Also a PID controller system is proposed to control the rotor speed of the wind turbine. The proposed mathematical model is developed in MATLAB-Simulink software. The simulation results showed that the developed controller can be used to control the wind turbine velocity.

scholarly journals Design and Analysis of a Wind Turbine Blade with Dimples to Enhance the Efficiency through CFD with ANSYS R16.0

2018 ◽  
Vol 207 ◽  
pp. 02004
Author(s):  
M. Rajaram Narayanan ◽  
S. Nallusamy ◽  
M. Ragesh Sathiyan
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Turbine Blades ◽  
Electrical Energy ◽  
Optimum Combination ◽  
Surface Topology ◽  
Wind Turbine Blades ◽  
Lift And Drag

In the global scenario, wind turbines and their aerodynamics are always subjected to constant research for increasing their efficiency which converts the abundant wind energy into usable electrical energy. In this research, an attempt is made to increase the efficiency through the changes in surface topology of wind turbines through computational fluid dynamics. Dimples on the other hand are very efficient in reducing air drag as is it evident from the reduction of drag and increase in lift in golf balls. The predominant factors influencing the efficiency of the wind turbines are lift and drag which are to be maximized and minimized respectively. In this research, surface of turbine blades are integrated with dimples of various sizes and arrangements and are analyzed using computational fluid dynamics to obtain an optimum combination. The analysis result shows that there is an increase in power with about 15% increase in efficiency. Hence, integration of dimples on the surface of wind turbine blades has helped in increasing the overall efficiency of the wind turbine.

scholarly journals Foundations, Design, and Dynamic Performance of Wind Turbines: Overview and Challenges in Sudan

2021 ◽  
Vol 9 (1) ◽  
pp. 96-103
Author(s):  
Ruba Asim Hamza ◽  
Amged Osman Abdelatif
Keyword(s):  
Dynamic Response ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Structural Damage ◽  
Renewable Energy Sources ◽  
Dynamic Performance ◽  
Scaled Model ◽  
Static Loads ◽  
Design Loads ◽  
Foundation Type

Sudan is one of the developing countries that suffers from a lack of electricity, where the national electrification rate is estimated at 38.5%. In order to solve this problem, it is possible to use renewable energy sources such as wind energy. Beside many aspects to be considered at the design of wind turbine foundations, more attention should be given to the geotechnical part. There are many types of foundations for wind turbines. The foundation must satisfy two design criteria: 1) It should be safe against bearing failure in soils under design loads and settlements during the life of the structure must not cause structural damage; 2) In addition to static loads, wind turbine foundations loads are extremely eccentrically and the loading is usually highly dynamic. Therefore, the selection of foundation type should consider these two criteria taking into account the nature and magnitude of these loads. This paper presents a review of different types of wind turbine foundations of focusing on on-shore wind turbine foundation types and the dynamic response of wind turbine. The paper also demonstrate experimentally the dynamic response of the wind turbines using wind tunnel facility test on a scaled model.  

scholarly journals Design of Supervisory Control for Speed Control of Wind Turbine using Torque-Control Method Based on Buck Converter

2020 ◽  
Vol 190 ◽  
pp. 00019
Author(s):  
Katherin Indriawati ◽  
Choirul Mufit ◽  
Andi Rahmadiansah
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Supervisory Control ◽  
Control Method ◽  
Speed Control ◽  
Buck Converter ◽  
Torque Control ◽  
Control Mode ◽  
Rotor Speed ◽  
Integral Control

The variation of wind speed causes the electric power generated by the turbine also varies. To obtain maximum power, the rotor speed of wind turbines must be optimally rated. The rotor speed can be controlled by manipulating the torque from the generator; this method is called Torque Control. In that case, a DC-DC converter is needed as the control actuator. In this study, a buck converter-based supervisory control design was performed on the Horizontal-axis wind turbines (HAWT). Supervisory control is composed of two control loops arranged in cascade, and there is a formula algorithm as the supervisory level. The primary loop uses proportional control mode with a proportional gain of 0.3, whereas in the secondary loop using proportional-integral control mode with a proportional gain of 5.2 and an integral gain of 0.1. The Supervisory control has been implemented successfully and resulted in an average increase in turbine power of 4.1 % at 5 m s–1 and 10.58 % at 6 m s–1 and 11.65 % at 7 m s–1, compared to wind turbine systems without speed control.

Research on Wind Turbine Blade Loads and Dynamics Factors

2014 ◽  
Vol 1014 ◽  
pp. 124-127
Author(s):  
Zhi Qiang Xu ◽  
Jian Huang
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Wind Turbines ◽  
Mechanical Energy ◽  
Turbine Blades ◽  
Electrical Energy ◽  
Wind Turbine Blade ◽  
Strength Analysis ◽  
Wind Turbine Blades ◽  
Turbine Wheel

Wind turbines consists of three key parts, namely, wind wheels (including blades, hub, etc.), cabin (including gearboxes, motors, controls, etc.) and the tower and Foundation. Wind turbine wheel is the most important part ,which is made up of blades and hubs. Blade has a good aerodynamic shape, which will produce aerodynamic in the airflow rotation, converting wind energy into mechanical energy, and then, driving the generator into electrical energy by gearbox pace. Wind turbine operates in the natural environment, their load wind turbine blades are more complex. Therefore load calculations and strength analysis for wind turbine design is very important. Wind turbine blades are core components of wind turbines, so understanding of their loads and dynamics by which the load on the wind turbine blade design is of great significance.

Effect of Slotted Angle on Savonius Wind Turbine Performance

2021 ◽  
Vol 104 ◽  
pp. 83-88
Author(s):  
Rahmat Wahyudi ◽  
Diniar Mungil Kurniawati ◽  
Alfian Djafar
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Electrical Energy ◽  
Speed Ratio ◽  
Angle Variation ◽  
Wind Speeds ◽  
Turbine Performance ◽  
Savonius Wind Turbine ◽  
Low Wind Speeds

The potential of wind energy is very abundant but its utilization is still low. The effort to utilize wind energy is to utilize wind energy into electrical energy using wind turbines. Savonius wind turbines have a very simple shape and construction, are inexpensive, and can be used at low wind speeds. This research aims to determine the effect of the slot angle on the slotted blades configuration on the performance produced by Savonius wind turbines. Slot angle variations used are 5o ,10o , and 15o with slotted blades 30% at wind speeds of 2,23 m/s to 4,7 m/s using wind tunnel. The result showed that a small slot angle variation of 5o produced better wind turbine performance compared to a standard blade at low wind speeds and a low tip speed ratio.

scholarly journals Vibration Reduction Strategy for Offshore Wind Turbines

2020 ◽  
Vol 10 (17) ◽  
pp. 6091
Author(s):  
Haoming Liu ◽  
Suxiang Yang ◽  
Wei Tian ◽  
Min Zhao ◽  
Xiaoling Yuan ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Output Power ◽  
Wind Turbines ◽  
Reference Signal ◽  
Offshore Wind ◽  
Wave Load ◽  
Offshore Wind Turbines ◽  
Pitch Control ◽  
Simulation Results ◽  
Aerodynamic Torque

The operational environment of offshore wind turbines is much more complex than that of onshore wind turbines. Facing the persistent wind and wave forces, offshore wind turbines are prone to vibration problems, which are not conducive to their long-term operation. Under this background, first, how the wave affects the vibration characteristics of offshore wind turbines is analyzed. Based on the existing wave and wave load models, we analytically show that there exist fluctuating components related to the hydrodynamic frequency in the aerodynamic load and aerodynamic torque of offshore wind turbines. Simulation results based on a GH Bladed platform further validates the analysis. Second, in order to reduce the joint impacts of the wave, wind shear and tower shadow on the wind turbine, a variable pitch control method is proposed. The integrated tower top vibration acceleration signal is superimposed on the collective pitch reference signal, then the triple frequency (3P) fluctuating component of the wind turbine output power and the azimuth angle of each blade are converted into the pitch angle adjustment signal of each blade, which is superimposed on the collective pitch signal for individual pitch control. The simulation results show that the proposed pitch control strategy can effectively smooth the fluctuation of blade root flap-wise load caused by wind and wave, and significantly reduce the fluctuation of aerodynamic torque and output power of offshore wind turbines.

The Rotor Speed Control of 5MW Wind Turbine under Rated Wind Speed Using Adaptive-PID Controller

2012 ◽  
Vol 229-231 ◽  
pp. 2323-2326
Author(s):  
Zong Qi Tan ◽  
Can Can Li ◽  
Hui Jun Ye ◽  
Yu Qiong Zhou ◽  
Hua Ling Zhu
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Pid Controller ◽  
Turbine Rotor ◽  
Speed Ratio ◽  
Rotor Speed ◽  
Rotating Speed ◽  
Tip Speed Ratio ◽  
Variable Wind ◽  
Wind Turbine Rotor

This paper designed the controller of the wind turbine rotor rotating speed. This model of adaptive-PID through control the tip-speed ratio and count the values of PID for variable wind speed. From the result of simulation, the wind speed can run in a good dynamic characteristic, and keep the rotor running in the best tip-speed ratio at the same time.

Planetary Gear for Counter-Rotating Wind Turbines

2014 ◽  
Vol 658 ◽  
pp. 135-140 ◽  
Author(s):  
Radu Saulescu ◽  
Codruta Jaliu ◽  
Olimpiu Munteanu ◽  
Oliver Climescu
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Rotation Speed ◽  
Planetary Gear ◽  
Electrical Energy ◽  
Turbine Rotor ◽  
Higher Power ◽  
Electrical Generator ◽  
High Rotation Speed ◽  
The Difference

A specific problem of the wind turbines refers to the difference between the low rotation speed of the wind turbine rotor and the high rotation speed needed for the electrical generator. Usually, the adaptation between the speed of the turbine rotor and the electrical generator speed is achieved by means of a speed increaser. A recent alternative relates to the use of coaxial counter-rotating wind turbines, which can achieve higher power and improve the conversion efficiency of the wind energy into electrical energy (up to 25%) with a reduced cost of approx. 20-30% compared to similar single rotor turbines. Conceptually, the counter-rotating wind turbine systems can integrate a particular generator wherein the rotor is coupled to a row of blades and the stator with another row of blades, or a commonly generator, coupled to a differential planetary gear, that allows the summation of the blades motions.The paper describes and analyzes kinematic and dynamic aspects of a system consisting of two coaxial counter-rotating turbines and a generator, interconnected by a planetary gear with two inputs (the two turbines) and an output (the generator). The algorithm is based on the property of the differential planetary gear of adding two input motions into one output motion. The kinematic and dynamic parameters of the planetary gear are established in the paper, and a case study is further presented: a small wind turbine equipped with a transmission enabling input speed multiplication.

scholarly journals Fault Tolerant Control of Internal Faults in Wind Turbine: Case Study of Gearbox Efficiency Decrease

2018 ◽  
Vol 2018 ◽  
pp. 1-8 ◽  
Author(s):  
Younes Ait El Maati ◽  
Lhoussain El Bahir ◽  
Khalid Faitah
Keyword(s):  
Steady State ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Fault Tolerant ◽  
Fault Tolerant Control ◽  
Operating Point ◽  
Rotor Speed ◽  
Integral Term ◽  
Internal Faults

This paper presents a method to control the rotor speed of wind turbines in presence of gearbox efficiency fault. This kind of faults happens due to lack of lubrication. It affects the dynamic of the principal shaft and thus the rotor speed. The principle of the fault tolerant control is to find a bloc that equalizes the dynamics of the healthy and faulty situations. The effectiveness decrease impacts on not only the dynamics but also the steady state value of the rotor speed. The last reason makes it mandatory to add an integral term on the steady state error to cancel the residual between the measured and operating point rotor speed. The convergence of the method is proven with respect to the rotor parameters and its effectiveness is evaluated through the rotor speed.

Offshore and Onshore Wind Energy Conversion: The Potential of a Novel Multiple-Generator Drivetrain

2013 ◽  
Vol 569-570 ◽  
pp. 644-651 ◽  
Author(s):  
Navid Goudarzi ◽  
Wei Dong Zhu
Keyword(s):  
Mathematical Model ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Simple Mathematical Model ◽  
Onshore Wind ◽  
Wind Energy Conversion ◽  
Qualitative And Quantitative ◽  
Advantages And Disadvantages ◽  
The Cost ◽  
Operational Range

A multiple generator drivetrain (MGD), where a single large generator in a wind turbine is replaced by multiple generators with the same or different rated powers, is proposed along with an automatic switch as an alternative to an existing MGD configuration. Qualitative and quantitative comparisons of a MGD with a conventional drivetrain are provided to better understand the advantages and disadvantages of having a MGD in wind turbines. New approaches for improving the efficiency and the reliability, expanding the operational range, and reducing the cost of a wind turbine are mentioned. A simple mathematical model for a MGD with electromagnetic clutches is developed, a novel prototype of a MGD is designed and fabricated, and experiments are conducted on the prototype. It is concluded that a multiple-generator drivetrain with generators operating individually or in parallel has a better potential of improving the efficiency and the reliability, expanding the operational range, and reducing the cost of offshore and onshore wind turbines than the existing MGD configuration.

Sign in / Sign up

Export Citation Format

Share Document