scholarly journals Simulation of Lid-Driven Cavity Flow with Internal Circular Obstacles

2020 ◽  
Vol 10 (13) ◽  
pp. 4583 ◽  
Author(s):  
Tingting Huang ◽  
Hee-Chang Lim
Keyword(s):  
Reynolds Number ◽  
Solid Wall ◽  
Vortex Formation ◽  
Flow Characteristics ◽  
Reynolds Numbers ◽  
Time Model ◽  
Cross Sectional ◽  
Driven Cavity ◽  
Secondary Vortices ◽  
Boltzmann Method

The Lattice Boltzmann method (LBM) has been applied for the simulation of lid-driven flows inside cavities with internal two-dimensional circular obstacles of various diameters under Reynolds numbers ranging from 100 to 5000. With the LBM, a simplified square cross-sectional cavity was used and a single relaxation time model was employed to simulate complex fluid flow around the obstacles inside the cavity. In order to made better convergence, well-posed boundary conditions should be defined in the domain, such as no-slip conditions on the side and bottom solid-wall surfaces as well as the surface of obstacles and uniform horizontal velocity at the top of the cavity. This study focused on the flow inside a square cavity with internal obstacles with the objective of observing the effect of the Reynolds number and size of the internal obstacles on the flow characteristics and primary/secondary vortex formation. The current LBM has been successfully used to precisely simulate and visualize the primary and secondary vortices inside the cavity. In order to validate the results of this study, the results were compared with existing data. In the case of a cavity without any obstacles, as the Reynolds number increases, the primary vortices move toward the center of the cavity, and the secondary vortices at the bottom corners increase in size. In the case of the cavity with internal obstacles, as the Reynolds number increases, the secondary vortices close to the internal obstacle become smaller owing to the strong primary vortices. In contrast, depending on the sizes of the obstacles ( R / L = 1/16, 1/6, 1/4, and 2/5), secondary vortices are induced at each corner of the cavity and remain stationary, but the secondary vortices close to the top of the obstacle become larger as the size of the obstacle increases.

Numerical Assessment of Turbulent Flow Driving in a Two-Sided Lid-Driven Cavity with Antiparallel Wall Motion

2021 ◽  
Vol 406 ◽  
pp. 133-148
Author(s):  
El Amin Azzouz ◽  
Samir Houat ◽  
Ahmed Zineddine Dellil
Keyword(s):  
Flow Characteristics ◽  
Turbulence Models ◽  
Reynolds Numbers ◽  
Systematic Evaluation ◽  
Driven Cavity ◽  
Rans Turbulence Models ◽  
Calculation Results ◽  
Two Dimensional Flow ◽  
Rsm Model ◽  
Secondary Vortices

In this paper, the case of the steady two-dimensional flow in a two-sided lid-driven square cavity is numerically investigated by the finite volume method (FVM). The flow motion is due to the top and bottom horizontal walls sliding symmetrically in the opposite direction with equal velocities, UT and UB, obtained through three respective Reynolds numbers, Re1,2=10000, 15000, and 20000. Due to the lack of availability of experimental results in this Reynolds number margin for this type of flow, the problem is first examined by considering that the flow is turbulent with the inclusion of four commonly used RANS turbulence models: Omega RSM, SST k-ω, RNG k-ε and Spalart-Allmaras (SA). Next, the regime is considered being laminar in the same range of Reynolds numbers. A systematic evaluation of the flow characteristics is performed in terms of stream-function contour, velocity profiles, and secondary vortices depth. Examination of the calculation results reveals the existence of a great similarity of the predicted flow structures between the Omega RSM model and those from the laminar flow assumption. On the other hand, the computed flow with the SST k-ω model, the RNG k-ε model, and the SA model reveals a remarkable under-prediction which appears clearly in the size and number of secondary vortices in the near-wall regions. Various benchmarking results are presented in this study.

Vortex Formation for Different Geometry of Cavities Using High Reynolds Number

2014 ◽  
Vol 699 ◽  
pp. 416-421
Author(s):  
Mohd Noor Asril Saadun ◽  
Muhammad Zulhakim Sharudin ◽  
Nor Azwadi Che Sidik ◽  
Mohd Hafidzal Mohd Hanafi
Keyword(s):  
Reynolds Number ◽  
High Reynolds Number ◽  
Stokes Equations ◽  
Vortex Formation ◽  
Flow Characteristics ◽  
Reynolds Numbers ◽  
Navier Stokes ◽  
Contaminant Removal ◽  
Navier Stokes Equations ◽  
High Reynolds

A preliminary study of Computational Fluid Dynamics (CFD) on the effect of high Reynolds numbers in the cavity has been carried out. Two dimensional model analysis of the flow characteristics were conducted using the numerical solution of Navier-Stokes equations based on the finite difference method. The flow characteristics in the cavity and the driven flow were modeled via turbulence equation modelling. This paper focuses on the effects of different high Reynolds number on the flow pattern of contaminant removal in the cavity. Different types of geometry and aspect ratio of the geometry were used as the parameters of the cavity in this study. Based on visualization of flows between each model with the different parameters used, the results of a comparison analysis focusing on the behavior of the flow were reported.

Experimental Investigation of Effect of Tip Coolant Ejection on Internal Flow Characteristics Within a Realistic Blade Coolant Channel

2013 ◽  
Author(s):  
Jian Pu ◽  
Zhaoqing Ke ◽  
Jianhua Wang ◽  
Lei Wang ◽  
Hongde You
Keyword(s):  
Experimental Investigation ◽  
Reynolds Number ◽  
Pressure Drop ◽  
Turbine Blade ◽  
Flow Rate ◽  
Flow Characteristics ◽  
Reynolds Numbers ◽  
Flow Ratio ◽  
Lp Turbine ◽  
Mass Flow Ratio

This paper presents an experimental investigation on the characteristics of the fluid flow within an entire coolant channel of a low pressure (LP) turbine blade. The serpentine channel, which keeps realistic blade geometry, consists of three passes connected by a 180° sharp bend and a semi-round bend, 2 tip exits and 25 trailing edge exits. The mean velocity fields within several typical cross sections were captured using a particle image velocimetry (PIV) system. Pressure and flow rate at each exit were determined through the measurements of local static pressure and volume flow rate. To optimize the design of LP turbine blade coolant channels, the effect of tip ejection ratio (ER) from 180° sharp bend on the flow characteristics in the coolant channel were experimentally investigated at a series of inlet Reynolds numbers from 25,000 to 50,000. A complex flow pattern, which is different from the previous investigations conducted by a simplified square or rectangular two-pass U-channel, is exhibited from the PIV results. This experimental investigation indicated that: a) in the main flow direction, the regions of separation bubble and flow impingement increase in size with a decrease of the ER; b) the shape, intensity and position of the secondary vortices are changed by the ER; c) the mass flow ratio of each exit to inlet is not sensitive to the inlet Reynolds number; d) the increase of the ER reduces the mass flow ratio through each trailing edge exit to the extent of about 23–28% of the ER = 0 reference under the condition that the tip exit located at 180° bend is full open; e) the pressure drop through the entire coolant channel decreases with an increase in the ER and inlet Reynolds number, and a reduction about 35–40% of the non-dimensional pressure drop is observed at different inlet Reynolds numbers, under the condition that the tip exit located at 180° bend is full open.

Numerical Simulation for Flow over Two Circular Cylinders in Micro Channel with Lattice Boltzmann Method

2014 ◽  
Vol 670-671 ◽  
pp. 747-750
Author(s):  
Zhi Jun Gong ◽  
Jiao Yang ◽  
Wen Fei Wu
Keyword(s):  
Lattice Boltzmann Method ◽  
Lattice Boltzmann ◽  
Recirculation Zone ◽  
Flow Characteristics ◽  
Reynolds Numbers ◽  
Circular Cylinders ◽  
Micro Channel ◽  
Zone Length ◽  
Spacing Ratio ◽  
Boltzmann Method

For indepth study on flow characteristics for fluid bypass obstacles in micro-channel, the Lattice Boltzmann Method (LBM) was used to simulate fluid flow over two circular cylinders in side-by-side arrangement of a micro-channel. The velocity distribution and recirculation zone length under different Reynolds numbers (Re = 0~100) and different spacing ratio (H/D= 0~2.0) were obtained. The results show that the pattern of flow and the size of recirculation zone in the micro-channel depend on the combined effect of Re and H/D.

Numerical Simulation of High Reynolds Number Flow Structure in a Lid-Driven Cavity Using MRT-LES

2014 ◽  
Vol 554 ◽  
pp. 665-669
Author(s):  
Leila Jahanshaloo ◽  
Nor Azwadi Che Sidik
Keyword(s):  
Reynolds Number ◽  
Lattice Boltzmann Method ◽  
Lattice Boltzmann ◽  
Numerical Technique ◽  
Lattice Boltzmann Model ◽  
Navier Stokes ◽  
Navier Stokes Equation ◽  
Driven Cavity ◽  
Reynolds Number Flow ◽  
Boltzmann Method

The Lattice Boltzmann Method (LBM) is a potent numerical technique based on kinetic theory, which has been effectively employed in various complicated physical, chemical and fluid mechanics problems. In this paper multi-relaxation lattice Boltzmann model (MRT) coupled with a Large Eddy Simulation (LES) and the equation are applied for driven cavity flow at different Reynolds number (1000-10000) and the results are compared with the previous published papers which solve the Navier stokes equation directly. The comparisons between the simulated results show that the lattice Boltzmann method has the capacity to solve the complex flows with reasonable accuracy and reliability. Keywords: Two-dimensional flows, Lattice Boltzmann method, Turbulent flow, MRT, LES.

scholarly journals Large-scaled simulation on the coherent vortex evolution of a jet in a cross-flow based on lattice Boltzmann method

2015 ◽  
Vol 19 (3) ◽  
pp. 977-988 ◽  
Author(s):  
Yanqin Shangguan ◽  
Xian Wang ◽  
Yueming Li
Keyword(s):  
Lattice Boltzmann Method ◽  
Lattice Boltzmann ◽  
Flow Characteristics ◽  
Cross Flow ◽  
Hairpin Vortex ◽  
Graphic Processing Units ◽  
Computational Performance ◽  
Good Ability ◽  
Secondary Vortices ◽  
Boltzmann Method

Large eddy simulation (LES) is performed on a jet issued normally into a cross-flow using lattice Boltzmann method (LBM) and multiple graphic processing units (multi-GPUs) to study the flow characteristics of jets in cross-flow (JICF). The simulation with 8 1.50?10 grids is fulfilled with 6 K20M GPUs. With large-scaled simulation, the secondary and tertiary vortices are captured. The features of the secondary vortices and the tertiary vortices reveal that they have a great impact on the mixing between jet flow and cross-flow. The qualitative and quantitative results also indicate that the evolution mechanism of vortices is not constant, but varies with different situations. The hairpin vortex under attached jet regime originates from the boundary layer vortex of cross-flow. While, the origin of hairpin vortex in detached jet is the jet shear-layer vortex. The mean velocities imply the good ability of LBM to simulate JICF and the large loss of jet momentum in detached jet caused by the strong penetration. Besides, in our computation, a high computational performance of 1083.5 MLUPS is achieved.

scholarly journals Entropy generation of a hybrid nanofluid on MHD mixed convection is a lid-driven cavity with partial heating having two rounded corners

2021 ◽  
Vol 321 ◽  
pp. 02004
Author(s):  
Zakaria Korei ◽  
Smail Benissaad
Keyword(s):  
Thermal Conductivity ◽  
Reynolds Number ◽  
Mixed Convection ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Object Oriented ◽  
Reynolds Numbers ◽  
Hybrid Nanofluid ◽  
Driven Cavity ◽  
Partial Heating

This research aims to investigate thermal and flow behaviors and entropy generation of magnetohydrodynamic Al2O3-Cu/water hybrid nanofluid in a lid-driven cavity having two rounded corners. A solver based on C ++ object-oriented language was developed where the finite volume was used. Parameter’s analysis is provided by varying Reynolds numbers (Re), Hartmann numbers (Ha), the volume fraction of hybrid nanofluid (ϕ), radii of the rounded corners. The findings show that reducing the radii of the rounded corners minimizes the irreversibility. Furthermore, the thermal conductivity and dynamic viscosity of hybrid nanofluid contribute to increasing the irreversibility. Finally, the entropy generation is decreased by increasing the Hartman number and increases by rising the Reynolds number.

Vortex Shedding From a Bluff Body Adjacent to a Plane Sliding Wall

1991 ◽  
Vol 113 (3) ◽  
pp. 384-398 ◽  
Author(s):  
M. P. Arnal ◽  
D. J. Goering ◽  
J. A. C. Humphrey
Keyword(s):  
Reynolds Number ◽  
Vortex Shedding ◽  
Bluff Body ◽  
Solid Wall ◽  
Reynolds Numbers ◽  
Careful Examination ◽  
Recirculation Region ◽  
Stream Velocity ◽  
Flow Past ◽  
Lower Reynolds Number

The characteristics of the flow around a bluff body of square cross-section in contact with a solid-wall boundary are investigated numerically using a finite difference procedure. Previous studies (Taneda, 1965; Kamemoto et al., 1984) have shown qualitatively the strong influence of solid-wall boundaries on the vortex-shedding process and the formation of the vortex street downstream. In the present study three cases are investigated which correspond to flow past a square rib in a freestream, flow past a rib on a fixed wall and flow past a rib on a sliding wall. Values of the Reynolds number studied ranged from 100 to 2000, where the Reynolds number is based on the rib height, H, and bulk stream velocity, Ub. Comparisons between the sliding-wall and fixed-wall cases show that the sliding wall has a significant destabilizing effect on the recirculation region behind the rib. Results show the onset of unsteadiness at a lower Reynolds number for the sliding-wall case (50 ≤ Recrit ≤100) than for the fixed-wall case (Recrit≥100). A careful examination of the vortex-shedding process reveals similarities between the sliding-wall case and both the freestream and fixed-wall cases. At moderate Reynolds numbers (Re≥250) the sliding-wall results show that the rib periodically sheds vortices of alternating circulation in much the same manner as the rib in a freestream; as in, for example, Davis and Moore [1982]. The vortices are distributed asymmetrically downstream of the rib and are not of equal strength as in the freestream case. However, the sliding-wall case shows no tendency to develop cycle-to-cycle variations at higher Reynolds numbers, as observed in the freestream and fixed-wall cases. Thus, while the moving wall causes the flow past the rib to become unsteady at a lower Reynolds number than in the fixed-wall case, it also acts to stabilize or “lock-in” the vortex-shedding frequency. This is attributed to the additional source of positive vorticity immediately downstream of the rib on the sliding wall.

Numerical Investigation on Turbulence Statistics and Heat Transfer of a Circular Jet Impinging on a Roughened Flat Plate

2021 ◽  
Vol 13 (4) ◽  
Author(s):  
Abdulrahman Alenezi ◽  
Abdulrahman Almutairi ◽  
Hamad Alhajeri ◽  
Abdulaziz Gamil ◽  
Faisal Alshammari
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Numerical Study ◽  
Roughness Element ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Target Plate ◽  
Cross Sectional ◽  
Flow Physics ◽  
Baseline Case

Abstract A detailed heat transfer numerical study of a three-dimensional impinging jet on a roughened isothermal surface is presented and is investigated from flow physics vantage point under the influence of different parameters. The effects of the Reynolds number, roughness location, and roughness dimension on the flow physics and heat transfer parameters are studied. Additionally, the relations between average heat transfer coefficient (AHTC) and flow physics including pressure, wall shear and flow vortices with thermodynamic nonequilibrium are offered. This paper studies the effect of varying both location and dimension of the roughness element which took the shape of square cross-sectional continuous ribs to deliver a favorable trade-off between total pressure loss and heat transfer rate. The roughness element was tested for three different radial locations (R/D) = 1, 1.5, and 2 and at each location its height (i.e., width) (e) was changed from 0.25 to 1 mm in incremental steps of 0.25. The study used a jet angle (α) of 90 deg, jet-to-target distance (H/D = 6), and Re ranges from 10,000 to 50,000, where H is the vertical distance between the target plate and jet exit. The results show that the AHTC can be significantly affected by changing the geometry and dimensions of the roughness element. This variation can be either an augmentation of, or decrease in, the (HTC) when compared with the baseline case. An enhancement of 12.9% in the AHTC was achieved by using optimal location and dimensions of the roughness element at specific Reynolds number. However, a diminution between 10% and 30% in (AHTC) was attained by the use of rib height e = 1 mm at Re = 50k. The variation of both rib location and height showed better contribution in increasing heat transfer for low-range Reynolds numbers.

scholarly journals Numerical Study of Flow Characteristics Around Confined Cylinder using OpenFOAM

2018 ◽  
Vol 7 (4.35) ◽  
pp. 617
Author(s):  
P. Mathupriya ◽  
L. Chan ◽  
H. Hasini ◽  
A. Ooi
Keyword(s):  
Reynolds Number ◽  
Vortex Shedding ◽  
Numerical Study ◽  
Vortex Formation ◽  
Plane Channel ◽  
Flow Characteristics ◽  
Strong Interactions ◽  
Two Dimensional ◽  
Computational Fluid Dynamics Cfd ◽  
Shedding Frequency

The numerical study of the flow over a two-dimensional cylinder which is symmetrically confined in a plane channel is presented to study the characteristics of vortex shedding. The numerical model has been established using direct numerical simulation (DNS) based on the open source computational fluid dynamics (CFD) code named OpenFOAM. In the present study, the flow fields have been computed at blockage ratio, β of 0.5 and at Reynolds number, Re of 200 and 300. Two-dimensional simulations investigated on the effects of Reynolds number based on the vortex formation and shedding frequency. It was observed that the presence of two distinct shedding frequencies appear at higher Reynolds number due to the confinement effects where there is strong interactions between boundary layer, shear layer and the wake of the cylinder. The range of simulations conducted here has shown to produce results consistent with that available in the open literature. Therefore, OpenFOAM is found to be able to accurately capture the complex physics of the flow.

Sign in / Sign up

Export Citation Format

Share Document