scholarly journals Rydberg Level Shift due to the Electric Field Generated by Rydberg Atom Collision Induced Ionization in Cesium Atomic Ensemble

2020 ◽  
Vol 10 (16) ◽  
pp. 5646 ◽  
Author(s):  
Xin Wang ◽  
Jun He ◽  
Jiandong Bai ◽  
Junmin Wang
Keyword(s):  
Electric Field ◽  
Electromagnetically Induced Transparency ◽  
Signal To Noise Ratio ◽  
Classical Model ◽  
Rydberg Atom ◽  
Optical Excitation ◽  
Atomic Ensemble ◽  
High Signal ◽  
Level Shift ◽  
Atom Collision

We experimentally studied the Rydberg level shift caused by the electric field, which is generated by Rydberg atom collision induced ionization in a cesium atomic ensemble. The density of charged particles caused by collisions between Rydberg atoms is changed by controlling the ground-state atomic density and optical excitation process. We measured the Rydberg level shift using Rydberg electromagnetically-induced-transparency (EIT) spectroscopy, and interpreted the physical origin using a semi-classical model. The experimental results are in good agreement with the numerical simulation. These energy shifts are important for the self-calibrated sensing of microwave field by the employing of Rydberg EIT. Moreover, in contrast to the resonant excitation case, narrow-linewidth spectroscopy with high signal-to-noise ratio would be useful for high-precision measurements.

scholarly journals Improvement of Microwave Electric Field Measurement Sensitivity via Multi-Carrier Modulation in Rydberg Atoms

2020 ◽  
Vol 10 (22) ◽  
pp. 8110
Author(s):  
Shaohua Li ◽  
Jinpeng Yuan ◽  
Lirong Wang
Keyword(s):  
Electric Field ◽  
Electromagnetically Induced Transparency ◽  
Signal To Noise Ratio ◽  
Rydberg Atom ◽  
High Sensitivity ◽  
Modulation Scheme ◽  
Measurement Sensitivity ◽  
System A ◽  
Spectral Signal ◽  
Induced Transparency

The microwave electric field intensity is precisely measured by the Autler–Townes splitting of electromagnetically induced transparency spectrum in a 5S1/2−5P3/2−57D5/2−58P3/2 four-level ladder-type 85Rb atomic system. A robust multi-carrier modulation scheme is employed to improve the spectral signal-to-noise ratio, which determines the optical readout of Rydberg atom-based microwave electrometry. As a result, a factor of 2 measurement sensitivity improvement is clearly achieved compared with the on resonant Autler–Townes splitting case credit to the advantage of matched filtering. This research paves the way for building a high sensitivity, portable sensor and offers a platform for achieving compact and sensitive receiver.

scholarly journals Field Distortion and Optimization of a Vapor Cell in Rydberg Atom-Based Radio-Frequency Electric Field Measurement

Sensors ◽  
2018 ◽  
Vol 18 (10) ◽  
pp. 3205 ◽  
Author(s):  
Zhenfei Song ◽  
Wanfeng Zhang ◽  
Qi Wu ◽  
Huihui Mu ◽  
Xiaochi Liu ◽  
...  
Keyword(s):  
Electric Field ◽  
Radio Frequency ◽  
Electromagnetically Induced Transparency ◽  
Rydberg Atom ◽  
Field Measurements ◽  
Field Vector ◽  
Systematic Investigation ◽  
Vapor Cell ◽  
Field Distortion ◽  
Vapor Cells

Highly excited Rydberg atoms in a room-temperature vapor cell are promising for developing a radio-frequency (RF) electric field (E-field) sensor and relevant measurement standards with high accuracy and sensitivity. The all-optical sensing approach is based on electromagnetically-induced transparency and Autler-Townes splitting induced by the RF E-field. Systematic investigation of measurement uncertainty is of great importance for developing a national measurement standard. The presence of a dielectric vapor cell containing alkali atoms changes the magnitude, polarization, and spatial distribution of the incident RF field. In this paper, the field distortion of rubidium vapor cells is investigated, in terms of both field strength distortion and depolarization. Full-wave numerical simulation and analysis are employed to determine general optimization solutions for minimizing such distortion and validated by measuring the E-field vector distribution inside different vapor cells. This work can improve the accuracy of atom-based RF E-field measurements and contributes to the development of related RF quantum sensors.

A compact guided-wave EMAT with pulsed electromagnet for ferromagnetic tube inspection

2020 ◽  
Vol 64 (1-4) ◽  
pp. 951-958
Author(s):  
Tianhao Liu ◽  
Yu Jin ◽  
Cuixiang Pei ◽  
Jie Han ◽  
Zhenmao Chen
Keyword(s):  
Power Plants ◽  
Signal To Noise Ratio ◽  
Small Diameter ◽  
Performance Testing ◽  
Guided Wave ◽  
High Signal ◽  
Receiver Coil ◽  
Signal To Noise ◽  
Corrosion Defects

Small-diameter tubes that are widely used in petroleum industries and power plants experience corrosion during long-term services. In this paper, a compact inserted guided-wave EMAT with a pulsed electromagnet is proposed for small-diameter tube inspection. The proposed transducer is noncontact, compact with high signal-to-noise ratio and unattractive to ferromagnetic tubes. The proposed EMAT is designed with coils-only configuration, which consists of a pulsed electromagnet and a meander pulser/receiver coil. Both the numerical simulation and experimental results validate its feasibility on generating and receiving L(0,2) mode guided wave. The parameters for driving the proposed EMAT are optimized by performance testing. Finally, feasibility on quantification evaluation for corrosion defects was verified by experiments.

Application of Novel Low Current OBIRCH Amplifier and Nanoprobing to Identify Subtle Leakages in Advanced Node Technologies

2018 ◽  
Author(s):  
Satish Kodali ◽  
Liangshan Chen ◽  
Yuting Wei ◽  
Tanya Schaeffer ◽  
Chong Khiam Oh
Keyword(s):  
Signal To Noise Ratio ◽  
Semiconductor Industry ◽  
Fault Isolation ◽  
Ring Oscillator ◽  
High Signal ◽  
The Novel ◽  
Resistance Change ◽  
Three Samples ◽  
Relative Threshold ◽  
First Time

Abstract Optical beam induced resistance change (OBIRCH) is a very well-adapted technique for static fault isolation in the semiconductor industry. Novel low current OBIRCH amplifier is used to facilitate safe test condition requirements for advanced nodes. This paper shows the differences between the earlier and novel generation OBIRCH amplifiers. Ring oscillator high standby leakage samples are analyzed using the novel generation amplifier. High signal to noise ratio at applied low bias and current levels on device under test are shown on various samples. Further, a metric to demonstrate the SNR to device performance is also discussed. OBIRCH analysis is performed on all the three samples for nanoprobing of, and physical characterization on, the leakage. The resulting spots were calibrated and classified. It is noted that the calibration metric can be successfully used for the first time to estimate the relative threshold voltage of individual transistors in advanced process nodes.

scholarly journals VS2 as saturable absorber for Q-switched pulse generation

Nanophotonics ◽  
2020 ◽  
Vol 9 (8) ◽  
pp. 2569-2576 ◽  
Author(s):  
Lu Li ◽  
Lihui Pang ◽  
Qiyi Zhao ◽  
Yao Wang ◽  
Wenjun Liu
Keyword(s):  
Saturable Absorber ◽  
Nonlinear Optical ◽  
Modulation Depth ◽  
Signal To Noise Ratio ◽  
Transition Metal Dichalcogenides ◽  
Laser Cavity ◽  
Pulse Generation ◽  
High Signal ◽  
Power Pulse ◽  
Metal Dichalcogenides

AbstractTransition metal dichalcogenides have been widely utilized as nonlinear optical materials for laser pulse generation applications. Herein, we study the nonlinear optical properties of a VS2-based optical device and its application as a new saturable absorber (SA) for high-power pulse generation. Few-layer VS2 nanosheets are deposited on the tapered region of a microfiber to form an SA device, which shows a modulation depth of 40.52%. After incorporating the microfiber-VS2 SA into an Er-doped fiber laser cavity, passively Q-switched pulse trains could be obtained with repetition rates varying from 95 to 233 kHz. Under the pump power of 890 mW, the largest output power and shortest pulse duration are measured to be 43 mW and 854 ns, respectively. The high signal-to-noise ratio of 60 dB confirms the excellent stability of the Q-switching state. To the best of our knolowdge, this is the first illustration of using VS2 as an SA. Our experimental results demonstrate that VS2 nanomaterials have a large potential for nonlinear optics applications.

scholarly journals Rydberg Atom Electric Field Sensors for Communications and Sensing

2021 ◽  
Vol 2 ◽  
pp. 1-13
Author(s):  
Charles T. Fancher ◽  
David R. Scherer ◽  
Marc C. St. John ◽  
Bonnie L. Schmittberger Marlow
Keyword(s):  
Electric Field ◽  
Rydberg Atom ◽  
Electric Field Sensors

scholarly journals Detection and localization of multiple small damages in beam

2021 ◽  
Vol 13 (1) ◽  
pp. 168781402098732
Author(s):  
Ayisha Nayyar ◽  
Ummul Baneen ◽  
Syed Abbas Zilqurnain Naqvi ◽  
Muhammad Ahsan
Keyword(s):  
Frequency Response ◽  
Natural Frequencies ◽  
Signal To Noise Ratio ◽  
Moving Average ◽  
A Priori ◽  
Damage Index ◽  
High Signal ◽  
Frequency Range ◽  
Spatial Locality ◽  
System Frequency

Localizing small damages often requires sensors be mounted in the proximity of damage to obtain high Signal-to-Noise Ratio in system frequency response to input excitation. The proximity requirement limits the applicability of existing schemes for low-severity damage detection as an estimate of damage location may not be known  a priori. In this work it is shown that spatial locality is not a fundamental impediment; multiple small damages can still be detected with high accuracy provided that the frequency range beyond the first five natural frequencies is utilized in the Frequency response functions (FRF) curvature method. The proposed method presented in this paper applies sensitivity analysis to systematically unearth frequency ranges capable of elevating damage index peak at correct damage locations. It is a baseline-free method that employs a smoothing polynomial to emulate reference curvatures for the undamaged structure. Numerical simulation of steel-beam shows that small multiple damages of severity as low as 5% can be reliably detected by including frequency range covering 5–10th natural frequencies. The efficacy of the scheme is also experimentally validated for the same beam. It is also found that a simple noise filtration scheme such as a Gaussian moving average filter can adequately remove false peaks from the damage index profile.

Sign in / Sign up

Export Citation Format

Share Document