scholarly journals Fabrication and Characterization of Clay-Polyethylene Composite Opted for Shielding of Ionizing Radiation

Crystals ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 1068
Author(s):  
S. F. Olukotun ◽  
S. T. Gbenu ◽  
K. O. Oyedotun ◽  
O. Fasakin ◽  
M. I. Sayyed ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Ionizing Radiation ◽  
Testing Machine ◽  
Xrd Analysis ◽  
Radiation Shielding ◽  
Aluminum Silicate ◽  
Displacement Effect ◽  
X Ray ◽  
Polyethylene Composite

This study fabricated and characterized a self-sustaining hydrogenous content clay-polyethylene composite opted for ionizing radiation shielding. Composites designated A–G were fabricated each containing 0–30 wt% of recycled low density polyethylene (LDPE), respectively. To know the effects of the incorporated LDPE on the morphology, microstructural, compressive strength, thermal property and displacement effect on the vital elements were studied using scanning electron microscopy (SEM), X-ray diffractometry (XRD), universal mechanical testing machine, differential thermal analysis (DTA), Rutherford backscattering (RBS) technique and particle induced X-ray emission (PIXE), respectively. The bulk densities of the clay composites ranged between 1.341 and 2.030 g/cm3. The samples’ XRD analysis revealed similar patterns, with a sharp and prominent peak at angle 2θ equals ~26.11°, which matched with card number 16-0606 of the Joint Committee on Powder Diffraction Standards (JCPDS) that represents Aluminum Silicate Hydroxide (Al2Si2O5(OH)4), a basic formula for Kaolin clay. The compressive strength ranged between 2.52 and 5.53 MPa. The ratio of Si to Al in each composite is about 1:1. The dehydroxylation temperature for samples ranged between 443.23 °C and 555.23 °C.

Preparation and Characterization of n-HA/PA66/CS Biocomposite

2007 ◽  
Vol 330-332 ◽  
pp. 463-466 ◽  
Author(s):  
Hong Zhao Xiang ◽  
Yu Bao Li ◽  
Yuan Hua Mu ◽  
Xue Jiang Wang ◽  
Hua Nan Wang ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Testing Machine ◽  
Xrd Analysis ◽  
High Heat ◽  
Precipitation Method ◽  
High Heat Resistance ◽  
Co Precipitation ◽  
Different Content ◽  
Chitosan Composite

Nano-hydroxyapatite/polyamide66/chitosan composite (n-HA/PA66/CS) was prepared by a co-precipitation method, and was characterized by TG/DTG, TEM, IR, XRD and Universal mechanical testing machine. TEM test showed that some rod like crystals were formed and distributed uniformly into polymer matrix, with a size of about Φ30nm×80nm. IR and XRD analysis showed that some chemical bonds and electrostatic interaction existed between n-HA and polymers. TG/DTG curves indicated that the composites possessed a talent of high heat-resistance. The compressive strength of composite changed with different content of three compounds, the maximum compressive strength of composite (70MPa) could be acquired.

Characterization and A Preliminary Study of TiO2 Synthesis from Lampung Iron Sand

2020 ◽  
Vol 849 ◽  
pp. 113-118
Author(s):  
Yayat Iman Supriyatna ◽  
Slamet Sumardi ◽  
Widi Astuti ◽  
Athessia N. Nainggolan ◽  
Ajeng W. Ismail ◽  
...  
Keyword(s):  
Food Packaging ◽  
Xrd Analysis ◽  
Major Elements ◽  
Raw Material ◽  
Solid Residue ◽  
X Ray Diffraction ◽  
X Ray ◽  
Leaching Solution ◽  
Ti Content

The purpose of this study is to characterize Lampung iron sand and to conduct preliminary experiments on the TiO2 synthesis which can be used for the manufacturing of functional food packaging. The iron sand from South Lampung Regency, Lampung Province that will be utilized as raw material. The experiment was initiated by sieving the iron sand on 80, 100, 150, 200 and 325 mesh sieves. Analysis using X-Ray Fluorescence (XRF) to determine the element content and X-Ray Diffraction (XRD) to observe the mineralization of the iron sand was conducted. The experiment was carried out through the stages of leaching, precipitation, and calcination. Roasting was applied firstly by putting the iron sand into the muffle furnace for 5 hours at a temperature of 700°C. Followed by leaching using HCl for 48 hours and heated at 105°C with a stirring speed of 300 rpm. The leaching solution was filtered with filtrate and solid residue as products. The solid residue was then leached using 10% H2O2 solution. The leached filtrate was heated at 105°C for 40 minutes resulting TiO2 precipitates (powder). Further, the powder was calcined and characterized. Characterization of raw material using XRF shows the major elements of Fe, Ti, Mg, Si, Al and Ca. The highest Ti content is found in mesh 200 with 9.6%, while iron content is about 80.7%. While from the XRD analysis, it shows five mineral types namely magnetite (Fe3O4), Rhodonite (Mn, Fe, Mg, Ca) SiO3, Quart (SiO2), Ilmenite (FeOTiO2) and Rutile (TiO2). The preliminary experiment showed that the Ti content in the synthesized TiO2 powder is 21.2%. The purity of TiO2 is low due to the presence of Fe metal which is dissolved during leaching, so that prior to precipitation purification is needed to remove impurities such as iron and other metals.

scholarly journals Preparation and Characterization of Immobilized Molybdenum Complex on Pillared Montmorillonite K-10

2018 ◽  
Vol 1 (1) ◽  
Author(s):  
Farah Wahida Harun ◽  
Siti Balkis Mahamat Nor ◽  
Siti Salhah Othman
Keyword(s):  
Structural Characteristics ◽  
Xrd Analysis ◽  
Attenuated Total Reflection ◽  
Basal Spacing ◽  
Molybdenum Complex ◽  
X Ray ◽  
Pillared Montmorillonite ◽  
Sem Micrograph ◽  
Pillaring Solution

This study was carried out to immobilize molybdenyl (VI) acetylacetonate (MoO2(acac)2) complex on alumina pillared montmorillonite K-10 (MMT K-10). Pillar MMT K-10 was produced by introducing MMT K-10 with a hydrolysis solution of NaOH with AlCl3. Different concentrations of pillaring solution were prepared in terms of OHto Al3+ ratio (0.5, 1.0, 1.5 and 2.0) to observe the structural characteristics of MMT K-10. The pillared materials were then immobilized with 0.1 M MoO2(acac)2 and were characterized using X-ray diffractometry (XRD), scanning electron microscopy coupled in an energy dispersive X-ray spectrometer (SEM-EDX) and Fourier transform infrared spectroscopy with attenuated total reflection (FTIR-ATR) techniques. FTIR bands at ca. 890 – 930 cm-1 indicate that the Mo complex was immobilized on the surface of pillared MMT K-10 not in between the layers. This is supported by the SEM and XRD analysis where the SEM micrograph showed deposition of Mo on the surface of MMT K-10 as well as no modification of basal spacing was observed by XRD. Meanwhile, the d(001) spacing of the alumina pillared MMT K10 samples were seen to increase slightly as the concentration of OH/Al3+ increased.

Production and Characterization of HVOF Sprayed NiCr-TiC Coatings Using SHS Powder Feedstock

2000 ◽  
Author(s):  
M.T. Blatchford ◽  
A.J. Horlock ◽  
D.G. McCartney ◽  
P.H. Shipway ◽  
J.V. Wood
Keyword(s):  
Thermal Spraying ◽  
Xrd Analysis ◽  
Powder Size ◽  
Coating Properties ◽  
X Ray Diffraction ◽  
Hvof Spraying ◽  
X Ray ◽  
Wear Rates ◽  
Powder Feedstock

Abstract In this paper, the production of NiCr-TiC powder by SHS, suitable for HVOF spraying, is discussed together with results on the microstructure and coating properties. Compacts for SHS were prepared by mixing elemental Ti and C with pre-alloyed Ni-20wt.% Cr powder to give an overall composition of 35wt.% NiCr and 65wt.% TiC. These were then ignited and a self-sustaining reaction proceeded to completion. Reacted compacts were crushed, sieved, and classified to give feedstock powders in size ranges of 10-45 µm and 45-75 µm. All powder was characterized prior to spraying based on particle size distribution, x-ray diffraction (XRD), and scanning electron microscopy (SEM/EDS). Thermal spraying was performed using both H2 and C3H6 as fuel gases in a UTP/Miller Thermal HVOF system. The resulting coatings were characterized by SEM and XRD analysis, and the microstructures correlated with powder size and spray conditions. Abrasive wear was determined by a modified 'dry sand rubber wheel' (DSRW) test and wear rates were measured. It has been found that wear rates comparable to those of HVOF sprayed WC-17wt% Co coatings can be achieved.

scholarly journals Effects of strain on La0.67-x Prx Ca0.33 MnO3, LaMn1-x Cox O3 and LaMn1-x Nix O3 magnetite samples

DYNA ◽  
2019 ◽  
Vol 86 (211) ◽  
pp. 278-287
Author(s):  
Javier Alberto Olarte Torres ◽  
María Cristina Cifuentes Arcila ◽  
Harvey Andrés Suárez Moreno
Keyword(s):  
Compressive Strength ◽  
Magnetic Susceptibility ◽  
Sol Gel ◽  
Morphological Characterization ◽  
Electric Resistivity ◽  
The Other ◽  
X Ray Diffraction ◽  
Metal Insulator ◽  
X Ray

This paper presents the results obtained from the synthesis and morphological characterization of different magnetite samples:  La0.67-x Prx Ca0.33 MnO3.LaMn1-x Cox O3 and LaMn1-x Nix O3 at 0.13 ≤ 𝑥𝑥 ≤ 0.67 produced by a solid-state reaction mechanism and 𝐿𝐿𝐿𝐿𝑀𝑀𝑀𝑀1−𝑥𝑥(𝐶𝐶𝐶𝐶/𝑁𝑁𝑁𝑁)𝑥𝑥𝑂𝑂3 at 0.0 ≤ 𝑥𝑥 ≤ 0.5 produced by the sol-gel method. These samples were characterized using X-ray diffraction spectroscopy and by measuring electric resistivity and magnetic susceptibility which were carried out as a function of temperature. Notably, the effects of strain and compressive strength on the lattices of magnetite samples were highly dependent on the concentration of 𝑃𝑃𝑟𝑟, 𝐶𝐶𝐶𝐶, and 𝑁𝑁𝑁𝑁. Moreover, the transition temperatures of metal-insulator and ferromagnetic-paramagnetic phases also largely depend on these strength effects, e.g., at higher concentrations of 𝑃𝑃𝑟𝑟, effects of increased strain strength were observed, relocating the shifts of ferromagnetic-paramagnetic transitions to lower temperatures. On the other hand, effects of increased compressive strength were observed at higher concentrations of 𝑁𝑁𝑁𝑁 and 𝐶𝐶𝐶𝐶, relocating the shifts of ferromagnetic-paramagnetic and metal-insulator transitions to higher temperatures.

Three-Dimensional Characterization of the Microstructure of Bioglass/Polyethylene Composite by X-Ray Microtomography

2007 ◽  
Vol 330-332 ◽  
pp. 503-506
Author(s):  
Xiao Wei Fu ◽  
Jie Huang ◽  
E.S. Thian ◽  
Serena Best ◽  
William Bonfield
Keyword(s):  
Spatial Distribution ◽  
Volume Fraction ◽  
Three Dimensional ◽  
X Ray ◽  
Polyethylene Composite ◽  
Bioactive Properties ◽  
Recent Developments ◽  
3D Information

A Bioglass® reinforced polyethylene (Bioglass®/polyethylene) composite has been prepared, which combines the high bioactivity of Bioglass® and the toughness of polyethylene. The spatial distribution of Bioglass® particles within the composite is important for the performance of composites in-vivo. Recent developments in X-ray microtomography (XμT) have made it possible to visualize internal and microstructural details with different X-ray absorbencies, nondestructively, and to acquire 3D information at high spatial resolution. In this study, the volume fraction and 3D spatial distribution of Bioglass® particles has been acquired quantitatively by XμT. The information obtained provides a foundation for understanding the mechanical and bioactive properties of the Bioglass®/polyethylene composites.

scholarly journals Characterization of Slag Reprocessing Tailings-Based Geopolymers in Marine Environment

Minerals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 832 ◽  
Author(s):  
Jie Wu ◽  
Jing Li ◽  
Feng Rao ◽  
Wanzhong Yin
Keyword(s):  
Compressive Strength ◽  
Marine Environment ◽  
Copper Slag ◽  
X Ray Diffraction ◽  
Strength Measurement ◽  
X Ray ◽  
Sodium Aluminosilicate ◽  
Marine Concrete ◽  
Sodium Aluminosilicate Hydrate

In this study, copper slag reprocessing tailings (CSRT) were synthesized into geopolymers with 40%, 50% and 60% metakaolin. The evolution of compressive strength and microstructures of CSRT-based geopolymers in a marine environment was investigated. Except for compressive strength measurement, the characterizations of X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), nuclear magnetic resonance (NMR) and scanning electron microscopy (SEM) were included. It was found that marine conditions changed the Si/Al ratio in the sodium-aluminosilicate-hydrate (N-A-S-H) gel backbone, promoted the geopolymerization process, led to more Q4(3Al), Q4(2Al) and Q4(1Al) gel formation and a higher compressive strength of the geopolymers. This provided a basis for the preparation of CSRT-based geopolymers into marine concrete.

Microstructural Characterization of Glass-to-Metal Brazed Joint

2012 ◽  
Vol 616-618 ◽  
pp. 1732-1735 ◽  
Author(s):  
Xi Hai Shen ◽  
Yu Gang Zheng ◽  
Liang Chang ◽  
Jin Jia Guo ◽  
Song Bin Ye ◽  
...  
Keyword(s):  
Thermal Power ◽  
Microstructural Characterization ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Solar Thermal Power ◽  
Brazed Joints ◽  
Brazed Joint ◽  
Scanning Electron

Aiming at the glass-to-metal seals serving in the Solar Thermal Power (STP), glass-to-metal vacuum brazed joints were studied. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis were performed to examine the microstructure and element contents of interface seam on the glass-to-metal vacuum brazed joints. Also, the compositional concentration of the interface seam was measured by using energy dispersive spectroscopy (EDS).

Sign in / Sign up

Export Citation Format

Share Document