scholarly journals A 2.1 GHz, 210 μW, —189 dBc/Hz DCO with Ultra Low Power DCC Scheme

Electronics ◽  
2021 ◽  
Vol 10 (7) ◽  
pp. 805
Author(s):  
Shi Zuo ◽  
Jianzhong Zhao ◽  
Yumei Zhou
Keyword(s):  
Low Power ◽  
Current Efficiency ◽  
Phase Noise ◽  
Duty Cycle ◽  
Semiconductor Manufacturing ◽  
Figure Of Merit ◽  
Room Temperature ◽  
Cmos Process ◽  
Ultra Low Power ◽  
Measured Phase

This article presents a low power digital controlled oscillator (DCO) with an ultra low power duty cycle correction (DCC) scheme. The DCO with the complementary cross-coupled topology uses the controllable tail resistor to improve the tail current efficiency. A robust duty cycle correction (DCC) scheme is introduced to replace self-biased inverters to save power further. The proposed DCO is implemented in a Semiconductor Manufacturing International Corporation (SMIC) 40 nm CMOS process. The measured phase noise at room temperature is −115 dBc/Hz at 1 MHz offset with a dissipation of 210 μμW at an oscillating frequency of 2.12 GHz, and the resulin figure-of-merit is s −189 dBc/Hz.

A 400 μW Near-Threshold Feedback Class-C VCO with Auto Amplitude Control

2018 ◽  
Vol 27 (05) ◽  
pp. 1850072
Author(s):  
Chenggang Yan ◽  
Chen Hu
Keyword(s):  
Low Power ◽  
Phase Noise ◽  
Feedback Loop ◽  
Cmos Process ◽  
Voltage Controlled Oscillator ◽  
Amplitude Control ◽  
Ultra Low Power ◽  
Class C ◽  
Low Phase Noise ◽  
Near Threshold

A 400[Formula: see text][Formula: see text]W near-threshold supply class-C voltage controlled oscillator (VCO) with amplitude feedback loop and auto amplitude control (AAC) is proposed in this paper. The amplitude feedback loop and AAC ensure the robust startup of the proposed VCO and automatically adapts it to the class-C mode in steady state. Consequently, ultra-low power can be achieved in AAC mode and low phase noise, high swing can be achieved in AAC off mode. The proposed VCO with AAC gets ultra-low power consumption by limiting the oscillating amplitude and driving the proposed VCO into the deep Class-C mode. Additionally, the peak value detector is employed in this work to boost the controlling voltage of capacitors bank. Thus, a low on resistance of switch transistors is obtained, which increases the Q value of capacitors bank. The simulated phase noise is [Formula: see text]124.5[Formula: see text]dBc/Hz at 1[Formula: see text]MHz offset with the 1.16[Formula: see text]GHz oscillation frequency. In this case, the figure-of-merit including tuning range (FOMT) of proposed VCO is [Formula: see text]195[Formula: see text]dBc/Hz. The proposed VCO is fabricated in SMIC 40[Formula: see text]nm CMOS process and consumes 0.62[Formula: see text]mA from 0.65[Formula: see text]V supply. The measured phase noise is [Formula: see text]109[Formula: see text]dBc/Hz and FOMT is [Formula: see text]179[Formula: see text]dBc/Hz.

A NOVEL ULTRA-LOW POWER TWO-TERMINAL ZENER VOLTAGE REFERENCE

2012 ◽  
Vol 21 (06) ◽  
pp. 1240017
Author(s):  
CHIANG LIANG KOK ◽  
LITER SIEK ◽  
WEI MENG LIM
Keyword(s):  
Low Power ◽  
Output Voltage ◽  
Room Temperature ◽  
Analog Circuit ◽  
Cmos Process ◽  
Threshold Region ◽  
Voltage Reference ◽  
Ultra Low Power ◽  
Average Temperature ◽  
Load Regulation

A novel ultra-low power two terminal zener voltage reference is designed and implemented. It realizes the concept of using sub-threshold region of the MOSFET to achieve a very low and stable output voltage within a two terminal circuit topology. This proposed voltage reference was fabricated with Global Foundries 0.18-μm CMOS process, consuming only a very small die area of 0.0009 mm2. Experimental results, carried out on five different silicon samples, explicitly show that it can yield a stable output voltage of 0.22 V at room temperature. It achieves an average temperature coefficient of 6.4 ppm/°C across a wide temperature range from 0°C to 150°C with a standard deviation of 2 ppm/°C. Furthermore, it achieves an ultra-low power consumption of 2 μW. The load regulation is 20 mV/V. This simple and innovative two terminal device can be used to provide a very low and constant voltage difference between any two nodes in an analog circuit.

scholarly journals An Ultra-Low-Power K-Band 22.2 GHz-to-26.9 GHz Current-Reuse VCO Using Dynamic Back-Gate-Biasing Technique

Electronics ◽  
2021 ◽  
Vol 10 (8) ◽  
pp. 889
Author(s):  
Xiaoying Deng ◽  
Peiqi Tan
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Tuning Range ◽  
Frequency Tuning ◽  
Cmos Process ◽  
Voltage Controlled Oscillator ◽  
Back Gate ◽  
Ultra Low Power ◽  
Current Reuse ◽  
K Band

An ultra-low-power K-band LC-VCO (voltage-controlled oscillator) with a wide tuning range is proposed in this paper. Based on the current-reuse topology, a dynamic back-gate-biasing technique is utilized to reduce power consumption and increase tuning range. With this technique, small dimension cross-coupled pairs are allowed, reducing parasitic capacitors and power consumption. Implemented in SMIC 55 nm 1P7M CMOS process, the proposed VCO achieves a frequency tuning range of 19.1% from 22.2 GHz to 26.9 GHz, consuming only 1.9 mW–2.1 mW from 1.2 V supply and occupying a core area of 0.043 mm2. The phase noise ranges from −107.1 dBC/HZ to −101.9 dBc/Hz at 1 MHz offset over the whole tuning range, while the total harmonic distortion (THD) and output power achieve −40.6 dB and −2.9 dBm, respectively.

scholarly journals A 0.3 V Rail-to-Rail Ultra-Low-Power OTA with Improved Bandwidth and Slew Rate

2021 ◽  
Vol 11 (2) ◽  
pp. 19
Author(s):  
Francesco Centurelli ◽  
Riccardo Della Sala ◽  
Pietro Monsurrò ◽  
Giuseppe Scotti ◽  
Alessandro Trifiletti
Keyword(s):  
Low Power ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Process ◽  
Slew Rate ◽  
Large Signal ◽  
Output Stage ◽  
Ultra Low Power ◽  
Input Stage ◽  
Rail To Rail

In this paper, we present a novel operational transconductance amplifier (OTA) topology based on a dual-path body-driven input stage that exploits a body-driven current mirror-active load and targets ultra-low-power (ULP) and ultra-low-voltage (ULV) applications, such as IoT or biomedical devices. The proposed OTA exhibits only one high-impedance node, and can therefore be compensated at the output stage, thus not requiring Miller compensation. The input stage ensures rail-to-rail input common-mode range, whereas the gate-driven output stage ensures both a high open-loop gain and an enhanced slew rate. The proposed amplifier was designed in an STMicroelectronics 130 nm CMOS process with a nominal supply voltage of only 0.3 V, and it achieved very good values for both the small-signal and large-signal Figures of Merit. Extensive PVT (process, supply voltage, and temperature) and mismatch simulations are reported to prove the robustness of the proposed amplifier.

scholarly journals A 219-µW ultra-low power low-noise amplifier for IEEE 802.15.4 based battery powered, portable, wearable IoT applications

2021 ◽  
Vol 3 (4) ◽  
Author(s):  
S. Chrisben Gladson ◽  
Adith Hari Narayana ◽  
V. Thenmozhi ◽  
M. Bhaskar
Keyword(s):  
Low Power ◽  
Ieee 802.15.4 ◽  
Low Voltage ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Cmos Process ◽  
Process Technology ◽  
Ultra Low Power ◽  
Power Mode ◽  
Noise Amplifier

AbstractDue to the increased processing data rates, which is required in applications such as fifth-generation (5G) wireless networks, the battery power will discharge rapidly. Hence, there is a need for the design of novel circuit topologies to cater the demand of ultra-low voltage and low power operation. In this paper, a low-noise amplifier (LNA) operating at ultra-low voltage is proposed to address the demands of battery-powered communication devices. The LNA dual shunt peaking and has two modes of operation. In low-power mode (Mode-I), the LNA achieves a high gain ($$S21$$ S 21 ) of 18.87 dB, minimum noise figure ($${NF}_{min.}$$ NF m i n . ) of 2.5 dB in the − 3 dB frequency range of 2.3–2.9 GHz, and third-order intercept point (IIP3) of − 7.9dBm when operating at 0.6 V supply. In high-power mode (Mode-II), the achieved gain, NF, and IIP3 are 21.36 dB, 2.3 dB, and 13.78dBm respectively when operating at 1 V supply. The proposed LNA is implemented in UMC 180 nm CMOS process technology with a core area of $$0.40{\mathrm{ mm}}^{2}$$ 0.40 mm 2 and the post-layout validation is performed using Cadence SpectreRF circuit simulator.

Sign in / Sign up

Export Citation Format

Share Document