scholarly journals Isolation Improvement in UWB-MIMO Antenna System Using Slotted Stub

Electronics ◽  
2020 ◽  
Vol 9 (10) ◽  
pp. 1582
Author(s):  
Ahsan Altaf ◽  
Amjad Iqbal ◽  
Amor Smida ◽  
Jamel Smida ◽  
Ayman A. Althuwayb ◽  
...  
Keyword(s):  
Multiple Input Multiple Output ◽  
Equivalent Circuit Model ◽  
Wide Band ◽  
Antenna System ◽  
Circuit Model ◽  
Antenna Element ◽  
Performance Parameters ◽  
Mimo Antenna ◽  
High Isolation ◽  
Large Bandwidth

Multiple-input multiple-output (MIMO) scheme refers to the technology where more than one antenna is used for transmitting and receiving the information packets. It enhances the channel capacity without more power. The available space in the modern compact devices is limited and MIMO antenna elements need to be placed closely. The closely spaced antennas undergo an undesirable coupling, which deteriorates the antenna parameters. In this paper, an ultra wide-band (UWB) MIMO antenna system with an improved isolation is presented. The system has a wide bandwidth range from 2–13.7 GHz. The antenna elements are closely placed with an edge to edge distance of 3 mm. In addition to the UWB attribute of the system, the mutual coupling between the antennas is reduced by using slotted stub. The isolation is improved and is below −20 dB within the whole operating range. By introducing the decoupling network, the key performance parameters of the antenna are not affected. The system is designed on an inexpensive and easily available FR-4 substrate. To better understand the working of the proposed system, the equivalent circuit model is also presented. To model the proposed system accurately, different radiating modes and inter-mode coupling is considered and modeled. The EM model, circuit model, and the measured results are in good agreement. Different key performance parameters of the system and the antenna element such as envelope correlation coefficient (ECC), diversity gain, channel capcity loss (CCL) gain, radiation patterns, surface currents, and scattering parameters are presented. State-of-the-art comparison with the recent literature shows that the proposed antenna has minimal dimensions, a large bandwidth, an adequate gain value and a high isolation. It is worth noticeable that the proposed antenna has high isolation even the patches has low edge-to-edge gap (3 mm). Based on its good performance and compact dimensions, the proposed antenna is a suitable choice for high throughput compact UWB transceivers.

scholarly journals A Graphene-Assembled Film Based MIMO Antenna Array with High Isolation for 5G Wireless Communication

2021 ◽  
Vol 11 (5) ◽  
pp. 2382
Author(s):  
Rongguo Song ◽  
Xiaoxiao Chen ◽  
Shaoqiu Jiang ◽  
Zelong Hu ◽  
Tianye Liu ◽  
...  
Keyword(s):  
Antenna Array ◽  
Antenna Arrays ◽  
Multiple Input Multiple Output ◽  
Frequency Selective Surface ◽  
Antenna System ◽  
Antenna Element ◽  
Mimo Antenna ◽  
High Isolation ◽  
Input Multiple Output ◽  
Alternative Material

With the development of 5G, Internet of Things, and smart home technologies, miniaturized and compact multi-antenna systems and multiple-input multiple-output (MIMO) antenna arrays have attracted increasing attention. Reducing the coupling between antenna elements is essential to improving the performance of such MIMO antenna system. In this work, we proposed a graphene-assembled, as an alternative material rather than metal, film-based MIMO antenna array with high isolation for 5G application. The isolation of the antenna element is improved by a graphene assembly film (GAF) frequency selective surface and isolation strip. It is shown that the GAF antenna element operated at 3.5 GHz has the realized gain of 2.87 dBi. The addition of the decoupling structure improves the isolation of the MIMO antenna array to more than 10 dB and corrects the antenna radiation pattern and operating frequency. The isolation between antenna elements with an interval of 0.4λ is above 25 dB. All experimental results show that the GAF antenna and decoupling structure are efficient devices for 5G mobile communication.

scholarly journals Dual-Band 2 × 2 MIMO Antenna with Compact Size and High Isolation Based on Half-Mode SIW

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Abubaker Ahmed Elobied ◽  
Xue-Xia Yang ◽  
Ningjie Xie ◽  
Steven Gao
Keyword(s):  
Multiple Input Multiple Output ◽  
Dual Band ◽  
Antenna Element ◽  
Mimo Antenna ◽  
High Isolation ◽  
Rectangular Patch ◽  
Compact Size ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Proximity Coupling

This paper presents a close-spaced dual-band 2 × 2 multiple-input multiple-output (MIMO) antenna with high isolation based on half-mode substrate integrated waveguide (HMSIW). The dual-band operation of the antenna element is achieved by loading a rectangular patch outside the radiating aperture of an HMSIW cavity. The HMSIW cavity is excited by a coaxial probe, whereas the rectangular patch is energized through proximity coupling by the radiating aperture of HMSIW. The antenna elements can be closely placed using the rotation and orthogonal arrangement for a 2 × 2 array. Small neutralization lines at the center of the MIMO antenna can increase the isolation among its elements by around 10 dB in the lower band and 5 dB in the higher band. A prototype of the MIMO antenna is fabricated and its performance is measured. The measured results show that the resonant frequencies are centered at 4.43 and 5.39 GHz with bandwidths of 110 and 80 MHz and peak gains of 6 and 6.4 dBi, respectively. The minimum isolation in both bands is greater than 35 dB. The envelope correlation coefficient is lower than 0.005 within two operating bands.

scholarly journals Modified U-Shaped Resonator as Decoupling Structure in MIMO Antenna

Electronics ◽  
2020 ◽  
Vol 9 (8) ◽  
pp. 1321
Author(s):  
Amjad Iqbal ◽  
Ahsan Altaf ◽  
Mujeeb Abdullah ◽  
Mohammad Alibakhshikenari ◽  
Ernesto Limiti ◽  
...  
Keyword(s):  
Multiple Input Multiple Output ◽  
Equivalent Circuit Model ◽  
Separation Distance ◽  
Antenna System ◽  
Parametric Modelling ◽  
Mimo Antenna ◽  
Antenna Performance ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Simple Assembly

This paper presents an isolation enhancement of two closely packed multiple-input multiple-output (MIMO) antenna system using a modified U-shaped resonator. The modified U-shaped resonator is placed between two closely packed radiating elements resonating at 5.4 GHz with an edge to edge separation distance of 5.82 mm (λ∘/10). Through careful adjustment of parametric modelling, the isolation level of −23 dB among the densely packed elements is achieved. The coupling behaviour of the MIMO elements is analysed by accurately designing the equivalent circuit model in each step. The antenna performance is realized in the presence and absence of decoupling structure, and the results shows negligible effects on the antenna performance apart from mutual coupling. The simple assembly of the proposed modified U-shaped isolating structure makes it useful for several linked applications. The proposed decoupling structure is compact in nature, suppress the undesirable coupling generated by surface wave and nearby fields, and is easy to fabricate.

scholarly journals A High Isolation MIMO Antenna without Decoupling Structure for LTE 700 MHz

2015 ◽  
Vol 2015 ◽  
pp. 1-7 ◽  
Author(s):  
Yanjie Wu ◽  
Yunliang Long
Keyword(s):  
Impedance Matching ◽  
Multiple Input Multiple Output ◽  
Monopole Antenna ◽  
Antenna Element ◽  
Mimo Antenna ◽  
High Isolation ◽  
Antenna Performance ◽  
Measurement Results ◽  
Multiple Input ◽  
Input Multiple Output

This paper presents a long-term evolution (LTE) 700 MHz band multiple-input-multiple-output (MIMO) antenna, and high isolation between the two symmetrical antenna elements is obtained without introducing extra decoupling structure. Each antenna element is a combination antenna of PIFA and a meander monopole antenna. The end of the PIFA and the meander monopole antenna are, respectively, overlapped with the 50 Ω microstrip feed line, the two overlapping areas produce additional capacitance which can be considered decoupling structures to enhance the isolation for the MIMO antenna, as well as the impedance matching of the antenna elements. The MIMO antenna is etched on FR4 PCB board with dimensions of 71 × 40 × 1.6 mm3; the edge-to-edge separation of the two antenna elements is only nearly 0.037 λat 700 MHz. Both simulation and measurement results are used to confirm the MIMO antenna performance; the operating bandwidth is 698–750 MHz withS11≤−6 dB andS21≤−23 dB.

Cordate-shaped UWB-MIMO antenna with notch band characteristic and high isolation

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Preeti Pannu ◽  
Devendra Kumar Sharma
Keyword(s):  
Multiple Input Multiple Output ◽  
Small Variation ◽  
Wide Band ◽  
Antenna System ◽  
Data Rate ◽  
Impedance Bandwidth ◽  
Defected Ground Structure ◽  
Content Type ◽  
Mimo Antenna ◽  
Good Agreement

Purpose This paper aims to design a most demanding low profile and compact ultra-wide band (UWB) antenna system for various wireless applications. The performance (in terms of data rate) of UWB system is improved by using multiple-input-multiple-output (MIMO) technology with it. Owing to the overlap of other existing licensed bands with that of UWB, electromagnetic signals can interfere. So, notched band UWB MIMO antenna system reported here which is highly compact, bandwidth efficient, superior data rate and high inter-element isolation comparatively to other reported designs. Design/methodology/approach A 49 × 49 × 1.6 mm3 quad-port UWB MIMO antenna with specific bandwidth elimination property is designed. The proposed planar MIMO configuration comprises unique four identical “Cordate-shaped” monopole radiators fed by 2.3-mm thick microstrip-lines. The radiators are located right-angled to each other to enhance inter-element isolation. Further, a different approach of slitted-substrate is applied to minimize the overall size and mutual coupling of the MIMO antenna, as a substitute of decoupling and matching structures. The defected ground structure is used to obtain −10 dB impedance bandwidth in entire UWB band, without compromising with the lower cut-off frequency response. Further, to eliminate the undesired resonant band (WLAN at 5.5 GHz) from UWB, a rounded split ring resonator is introduced in monopole patch. Findings In the entire operating band of 2.8 to 11 GHz, isolation among elements is more than 24 dB, envelope correlation coefficient less than 0.002, diversity gain greater than 9.99 dB and TARC less than −7 dB are obtained at all 4-ports. Research limitations/implications The measured parameters of the fabricated prototype antenna on FR4 substrate are found in good agreement with the simulated results. The small variation in software results and hardware results are observed due to hardware design limitations. Practical implications The proposed design may be used for any wireless application following in the range of UWB. Originality/value It can be shown from graphs of measured parameters of the fabricated prototype antenna. They found to be in good agreement with the simulated results.

scholarly journals Eight Element Side Edged Framed MIMO Antenna Array for Future 5G Smart Phones

Micromachines ◽  
2020 ◽  
Vol 11 (11) ◽  
pp. 956 ◽  
Author(s):  
Saad Hassan Kiani ◽  
Ahsan Altaf ◽  
Mujeeb Abdullah ◽  
Fazal Muhammad ◽  
Nosherwan Shoaib ◽  
...  
Keyword(s):  
Liquid Crystal Display ◽  
Multiple Input Multiple Output ◽  
Cost Effective ◽  
Antenna System ◽  
Human Hand ◽  
Single Element ◽  
Performance Parameters ◽  
Mimo Antenna ◽  
Principal Performance ◽  
On Chip

This paper presents a novel design of a Multiple Input Multiple Output (MIMO) antenna system for next generation sub 6 GHz 5G and beyond mobile terminals. The proposed system is composed of a main board and two side boards. To make the design cost-effective, FR4 is used as a substrate. The design is based on a unit monopole antenna etched at the side substrate. The single element is resonating at 3.5 GHz attaining a 10 dB bandwidth of 200 MHz and a 6 dB bandwidth of 400 MHz. The single element is then transformed into an MIMO array of 8-elements with an overall dimension of 150 mm × 75 mm × 7 mm, providing pattern diversity characteristics and isolation better than −12 dB for any two radiating elements. A number of studies such as effects of human hand on the system that includes single hand mode and dual mode scenarios and the effects of Liquid Crystal Display (LCD) over the principal performance parameters of the system are presented. The envelop correlation coefficient (ECC) is computed for all the scenarios and it is found that ECC is less than 0.1 for any case and maximum channel capacity is 38.5 bps/Hz within the band of interest. The main advantage of the proposed design over available designs in the literature is that almost all of the main substrate is empty providing wide space for different sensors, systems, and mobile technology components. A brief literature comparison of the proposed system is also presented. To validate the proposed model, a prototype is fabricated and results are presented. This design can be applied on higher frequencies to future micromachines for on chip communications using same theocratical approach as the space for higher frequencies in mmwave spectrum has been reserved. The simulated results are in an excellent agreement with the measured results. All the main performance parameters of the design are calculated and compared with the measured results wherever possible.

scholarly journals Compact Fractal MIMO antenna for UWB applications

2021 ◽  
Vol 20 ◽  
pp. 146-151
Author(s):  
Edgar Alejandro Andrade-Gonzalez ◽  
Juan Carlos Ordoñez-Martínez ◽  
Mario Reyes-Ayala ◽  
José Alfredo Tirado Méndez ◽  
Hilario Terres-Peña
Keyword(s):  
Multiple Input Multiple Output ◽  
Wide Band ◽  
Antenna System ◽  
Wide Frequency Range ◽  
Frequency Range ◽  
Mimo Antenna ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Uwb Applications ◽  
Uwb Communication

In this article, a compact ultra-wide band (UWB) multiple input multiple output (MIMO) antenna system is showed. This antenna is based on fractal Fibonacci circles and operates over wide frequency range from 2.9 to 14.51 GHz. The dielectric used was Duroid substrate with dielectric constant εr = 2.2 and thickness of substrate 1.27 mm. This UWB MIMO antenna is simulated by HFSS. In order to improve the isolation between the elements of the antenna a parasitic structure is used, getting S12 and very low ECC. Also, the Total Active reflection Coefficient (TARC) was obtained. Proposed antenna can be used for UWB communication applications and its size is 64 × 38mm2

scholarly journals CSRR Loaded 2x1 Triangular MIMO Antenna for LTE Band Operation

2017 ◽  
Vol 6 (3) ◽  
pp. 78 ◽  
Author(s):  
C. J. Malathi ◽  
D. Thiripurasundari
Keyword(s):  
Patch Antenna ◽  
Ground Plane ◽  
Multiple Input Multiple Output ◽  
Split Ring Resonator ◽  
Antenna System ◽  
Antenna Element ◽  
Single Element ◽  
Mimo Antenna ◽  
Antenna Miniaturization ◽  
Input Multiple Output

A 2´1 (two-element) multiple-input multiple-output (MIMO) patch antenna system is designed and fabricated for (2.43 – 2.57) GHz LTE band 7 operation. It uses comple-mentary split -ring resonator (CSRR) loading on its ground plane for antenna miniaturization. This reduces the single-element antenna size by 76%. The total board size of the proposed MIMO antenna system, including the GND plane is 50´50´0.8mm3, while the single-patch antenna element has a size of 18.5 ´16mm2. The antenna is fabricated and tested. Measured results are in good agreement with simulations. A minimum measured isolation of 10 dB is obtained given the close interelement spacing of 0.17λ.

scholarly journals Highly Compact MIMO Antenna System for LTE/ISM Applications

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
Lingsheng Yang ◽  
Tao Li ◽  
Su Yan
Keyword(s):  
Multiple Input Multiple Output ◽  
Antenna System ◽  
Antenna Element ◽  
Radiation Characteristics ◽  
Total Size ◽  
Mimo Antenna ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Operating Bandwidth ◽  
Planar Monopole Antenna

Planar monopole antenna is proposed as the antenna element to form a compact dual-element multiple-input-multiple-output (MIMO) antenna system for LTE2300 (used in Asia and Africa) and ISM band operation. The system can cover a 310 MHz (2.20–2.51 GHz) operating bandwidth, with the total size of 15.5 mm × 18 mm × 1.6 mm. Measured isolation higher than 16 dB is obtained without any specially designed decoupling structures, while the edge-to-edge element spacing is only 7.8 mm (0.08λat 2.20 GHz). Radiation characteristics, correlation coefficient, and the performance of the whole system with a metal sheet and a plastic housing show this system is competitive for practical MIMO applications. The antenna element is further used to build an eight-element MIMO antenna system; also good results are achieved.

scholarly journals MIMO­­­-CSRR Antenna for ISM Band Applications

2021 ◽  
Author(s):  
satish kumar ◽  
Gunasekaran Thangavel ◽  
Said Amer Salim Al Ismaili Ismaili ◽  
Balambigai Subramanian
Keyword(s):  
Ground Plane ◽  
Multiple Input Multiple Output ◽  
Split Ring Resonator ◽  
Antenna System ◽  
Antenna Element ◽  
Mimo Antenna ◽  
Ism Band ◽  
Complementary Split Ring Resonator ◽  
Single Antenna ◽  
Input Multiple Output

Abstract For the operation of 2.45GHz ISM band, a 2x2 Multiple Input Multiple Output (MIMO) antenna system is designed and fabricated. Complementary Split Ring Resonator (CSRR) is used in the MIMO patch and loaded on its ground plane to miniaturize the single antenna element. The single patch antenna element of 14x18 mm2 is fixed in a board of the Designed MIMO antennae system measuring 100x50x0.8 mm3. The antenna is tested by measuring radiation pattern, gain, VSWR, mutual coupling and return loss. The results of the Designed antenna systems are in good agreement with the simulations. In comparison to a conventional microstrip antenna, the Designed antenna achieves a 75% reduction in the resonant frequency.

Sign in / Sign up

Export Citation Format

Share Document