scholarly journals Influences of the Flow Cut and Axial Lift of the Impeller on the Aerodynamic Performance of a Transonic Centrifugal Compressor

Energies ◽  
2019 ◽  
Vol 12 (23) ◽  
pp. 4503
Author(s):  
Kun Park ◽  
In Jung ◽  
Sung You ◽  
Seung Lee ◽  
Ali Zamiri ◽  
...  
Keyword(s):  
Flow Rate ◽  
Centrifugal Compressor ◽  
Total Pressure ◽  
Relative Velocity ◽  
Axial Direction ◽  
Aerodynamic Performance ◽  
Design Flow ◽  
Design Point ◽  
Transonic Centrifugal Compressor ◽  
Design Flow Rate

In this study, the influences of the flow cut and axial lift of the impeller on the aerodynamic performance of a transonic centrifugal compressor were analyzed. The flow cut is a method to reduce the flow rate by decreasing the impeller passage height. The axial lift is a method of increasing the impeller passage height in the axial direction, which increases the impeller exit width (B2) and increases the total pressure. A NASA CC3 transonic centrifugal compressor with a backswept angle was used as a base compressor. After applying the flow cut, the total pressure at the target flow rate was lower than the total pressure at the design point due to the increase in the relative velocity at the impeller exit. After applying the axial lift, the total pressure at the design flow rate was increased, which was caused by the reduction in the relative velocity as the passage area at the impeller exit was increased. By applying the flow cut and axial lift methods, it was shown that the variation in relative velocity at the impeller exit has a significant effect on the variation in total pressure. In addition, it was found that the relative velocity at the impeller exit of the target flow rate is maintained similar to the base impeller when the flow cut and the axial lift are combined. Therefore, by combining the flow cut and the axial lift, three transonic centrifugal impellers with flow fractions of 0.7, 0.8, and 0.9 compared to the design flow rate were newly designed.

Compressible Simulation of Flow and Sound Around a Small Axial-Flow Fan With Flow Through Casing Slits

2020 ◽  
Vol 142 (10) ◽  
Author(s):  
Hiroshi Yokoyama ◽  
Katsutake Minowa ◽  
Kohei Orito ◽  
Masahito Nishikawara ◽  
Hideki Yanada
Keyword(s):  
Flow Field ◽  
Flow Rate ◽  
Aerodynamic Performance ◽  
Design Flow ◽  
Low Flow ◽  
Axial Fan ◽  
Flow Rates ◽  
Blade Tip ◽  
Flow Through ◽  
Design Flow Rate

Abstract Small axial fans are used for cooling electronic equipment and are often installed in a casing with various slits. Direct aeroacoustic simulations and experiments were performed with different casing opening ratios to clarify the effects of the flow through the casing slits on the flow field and acoustic radiation around a small axial fan. Both the predicted and measured results show that aerodynamic performance deteriorates at and near the design flow rate and is higher at low flow rates by completely closing the casing slits compared with the fan in the casing with slits. The predicted flow field shows that the vortical structures in the tip vortices are spread by the suppression of flow through the slits at the design flow rate, leading to the intensification of turbulence in the blade wake. Moreover, the pressure fluctuations on the blade surface are intensified, which increases the aerodynamic sound pressure level. The suppression of the outflow of pressurized air through the downstream part of the slits enhances the aerodynamic performance at low flow rates. Also, the predicted surface streamline at the design flow rate shows that air flows along the blade tip for the fan with slits, whereas the flow toward the blade tip appears for the fan without slits. As a result, the pressure distributions on the blade and the torque exerted on the fan blade are affected by the opening ratio of slits.

Effects of Upstream Bend on Aerodynamic Performance of a Transonic Centrifugal Compressor

2019 ◽  
Author(s):  
Kazutoyo Yamada ◽  
Masato Furukawa ◽  
Hiromitsu Arai ◽  
Sasuga Ito
Keyword(s):  
Flow Rate ◽  
Centrifugal Compressor ◽  
Leading Edge ◽  
Aerodynamic Performance ◽  
Circumferential Velocity ◽  
Low Flow ◽  
Inlet Pipe ◽  
Reversed Flow ◽  
Transonic Centrifugal Compressor ◽  
Bent Pipe

Abstract This paper describes the influence of a bent inlet pipe installed immediately upstream of a transonic centrifugal compressor on the aerodynamic performance and the stability. In order to clarify the influence of the bent inlet pipe, the internal flow fields in the inlet pipe, the impeller, and the diffuser of the compressor have been numerically investigated by a DES (Detached Eddy Simulation). For the purpose of comparison, the simulation was also conducted for the case of uniform axial inflow using a straight pipe. In order to make clear the influence of non-uniform flow with a bent pipe as far as possible, a 90-degree bent pipe was installed immediately upstream of the compressor, that is 0.86 times the inlet inner diameter. In the case of installing the bent pipe on the upstream of the compressor, the pressure ratio decreased on the high flow rate side in the compressor performance characteristic, whereas it increased at the low flow rate side. At the low flow rate operating point, there is a reversed flow occurring in the compressor impeller on the shroud side near the blade leading-edge. Installation of the bent pipe promotes mixing between the reversed flow and the main flow at the inlet of the compressor thanks to occurrence of a secondary flow. Since the reversed flow comes out from inside of the impeller, it has a high circumferential velocity. Therefore, the mixing of the reversed flow makes the compressor inlet flow a pre-swirl flow, and thereby the incidence decreases. As a result, leading-edge separation on the blade tip side of the impeller is suppressed, and the flow field inside the impeller is improved. In the diffuser section, when the bent pipe is installed, the circumferential velocity of the impeller exit flow increases on the hub side, whereas the radial velocity decreases. As a result, the diffuser performance is deteriorated and the diffuser stall tends to occur.

Experimental Investigation of Surge Phenomena in a Transonic Centrifugal Compressor With Inlet Distortion

2020 ◽  
Author(s):  
Sasuga Ito ◽  
Masato Furukawa ◽  
Satoshi Gunjishima ◽  
Takafumi Ota ◽  
Kazuhito Konishi ◽  
...  
Keyword(s):  
Flow Rate ◽  
Centrifugal Compressor ◽  
Flow Instability ◽  
Pressure Sensors ◽  
Low Flow ◽  
Inlet Distortion ◽  
Transonic Centrifugal Compressor ◽  
Response Pressure ◽  
Surge Phenomena ◽  
Low Flow Rate

Abstract Inlet distortion has influence on the aerodynamic performance of turbomachinery such as compressors, turbines and fans. On turbochargers, bent pipes are installed around the compressor due to the spatial limitations in the engine room of the vehicle. As the result, the compressor is operated with the distorted inflow. In the low flow rate operation, the distorted inflow also affects the flow instability like stall and surge. Especially, the operation range on the low flow rate side is defined based on the flow rate where surge occurs, so it is important to investigate the effect of the distorted inflow on surge. In this study, the effect of the inlet distortion to surge phenomena has been investigated by the experiments with a transonic centrifugal compressor. A bent pipe has been installed at the upstream of the compressor to generate a distorted flow. Experiments have been also conducted under the condition that a straight pipe was installed upstream of the compressor, and unsteady measurements with high response pressure sensors and an I-type hot wire probe have been carried out to each experiments. In addition, Fast Fourier transform (FFT) and Wavelet transform have been applied to the unsteady measurement results obtained from each experiment.

1D and 3D-Design Strategies for Pressure Slope Optimization of High-Flow Transonic Centrifugal Compressor Impellers

2018 ◽  
Author(s):  
A. Hildebrandt ◽  
T. Ceyrowsky
Keyword(s):  
Centrifugal Compressor ◽  
High Flow ◽  
Flow Coefficient ◽  
Design Parameters ◽  
Angle Distribution ◽  
Compressor Stage ◽  
Impeller Blade ◽  
Design Point ◽  
Centrifugal Compressor Stage ◽  
Transonic Centrifugal Compressor

The present paper deals with the numerical and theoretical investigations of the effect of geometrical dimensions and 1D-design parameters on the impeller pressure slope of a transonic centrifugal compressor stage for industrial process application. A database being generated during the multi-objective and multi-point design process of a high flow coefficient impeller, comprising 545 CFD (Computational Fluid Dynamics) designs is investigated in off-design and design conditions by means of RANS (Reynolds Averaged Navier Stokes) simulation of an impeller with vaneless diffuser. For high flow coefficients of 0.16 < phi < 0.18, the CFD-setup has been validated against measurement data regarding stage and impeller performance taken from MAN test rig experimental data for a centrifugal compressor stage of similar flow coefficient. The paper aims at answering the question how classical design parameter, such as the impeller blade angle distribution, impeller suction diameter and camber line length affect the local and total relative diffusion and pressure slope towards impeller stall operation. A second order analysis of the CFD database is performed by cross-correlating the CFD data with results from impeller two-zone 1D modelling and a rapid loading calculation process by Stanitz and Prian. The statistical covariance of first order 1D-analysis parameters such as the mixing loss of the impeller secondary flow, the slip factor, impeller flow incidence is analyzed, thereby showing strong correlation with the design and off-design point efficiency and pressure slope. Finally, guide lines are derived in order to achieve either optimized design point efficiency or maximum negative pressure slope characteristics towards impeller stall operation.

scholarly journals Modeling Study of Design Flow Rates for Cascade Water Supply Systems in Residential Skyscrapers

Water ◽  
2019 ◽  
Vol 11 (12) ◽  
pp. 2580
Author(s):  
Yang Zhou ◽  
Eric Lee ◽  
Ling-Tim Wong ◽  
Kwok-Wai Mui
Keyword(s):  
Water Supply ◽  
Mathematical Models ◽  
Flow Rate ◽  
Supply System ◽  
Water Supply System ◽  
Design Flow ◽  
Water Volume ◽  
Water Supply Systems ◽  
Supply Systems ◽  
Design Flow Rate

Skyscrapers are common nowadays around the world, especially in cities with limited development area. In order to pump water up to the higher level of a skyscraper, a cascade water supply system has to be installed. Currently, cascade water supply systems are mainly designed based on practical experiences or requirements of existing standards/guidelines that, in fact, are not specifically for skyscrapers. However, thorough studies on cascade water supply system designs are still limited in the literature. This study proposes mathematical models and uses Monte Carlo simulations to evaluate the design flow rate of a typical cascade water supply system that feeds various appliances in a residential skyscraper in Hong Kong. Graphs that showed the correlations between the inflow rate in the supply pipe and water volume in the tank are obtained. While tank storage volume is confirmed, the design flow rate of the cascade water supply system can be determined from these graphs. The proposed mathematical models can also be applied to evaluate the design flow rate of cascade water supply systems in other types of skyscrapers (e.g., office, commercial building) as well as with the changes in water demand patterns in the models.

scholarly journals Experimental Analysis on Pressure Fluctuation Characteristics of a Centrifugal Pump with Vaned-Diffuser

Water ◽  
2019 ◽  
Vol 12 (1) ◽  
pp. 126
Author(s):  
Houlin Liu ◽  
Ruichao Xia ◽  
Kai Wang ◽  
Yucheng Jing ◽  
Xianghui He
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Fluctuation ◽  
Dominant Frequency ◽  
Design Flow ◽  
Signal Source ◽  
Vaned Diffuser ◽  
Impeller Outlet ◽  
Variation Tendency ◽  
Design Flow Rate

Experimental measurements to analyze the pressure fluctuation performance of a centrifugal pump with a vaned-diffuser, which its specific speed is 190. Results indicate that the main cause of pressure fluctuation is the rotor-stator interference at the impeller outlet. The head of the pump with vaned-diffuser at the design flow rate is 15.03 m, and the efficiency of the pump with a vaned-diffuser at the design flow rate reaches 71.47%. Pressure fluctuation decreases gradually with increasing distance from the impeller outlet. Along with the increase of the flow rate, amplitude of pressure fluctuation decreases. The amplitude of pressure fluctuation at the measuring points near the diffusion section of the pump body is larger than other measuring points. The variation tendency of pressure fluctuation at P1–P10 is the same, while there are wide frequency bands with different frequencies. The dominant frequency of pressure fluctuation is the blade passing frequency. The rotor-stator interference between the impeller and the vaned-diffuser gives rise to the main signal source of pressure fluctuation.

Clocking effect in a centrifugal pump with a vaned diffuser

2020 ◽  
Vol 34 (26) ◽  
pp. 2050286
Author(s):  
Fen Lai ◽  
Xiangyuan Zhu ◽  
Yongqiang Duan ◽  
Guojun Li
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Loss ◽  
Total Pressure ◽  
Radial Force ◽  
Design Flow ◽  
Total Pressure Loss ◽  
Inlet Section ◽  
Centrifugal Pumps ◽  
Installation Angle

The performance and service life of centrifugal pumps can be influenced by the clocking effect. In this study, 3D numerical calculations based on the k-omega shear stress transport model are conducted to investigate the clocking effect in a centrifugal pump. Time-averaged behavior and transient behavior are analyzed. Results show that the optimum diffuser installation angle in the centrifugal pump is [Formula: see text] due to the minimum total pressure loss and radial force acting on the impeller. Total pressure loss, particularly in the volute, is considerably influenced by the clocking effect. The difference in total pressure loss in the volute at different clocking positions is 2.75 m under the design flow rate. The large total pressure loss in the volute is primarily caused by the large total pressure gradient within the vicinity of the volute tongue. The radial force acting on the impeller is also considerably affected by the clocking effect. When the diffuser installation angle is [Formula: see text], flow rate fluctuations in the volute and impeller passage are minimal, and flow rate distribution in the diffuser passage is more uniform than those in other diffuser installation angles. Moreover, static pressure fluctuations in the impeller midsection and the diffuser inlet section are at the minimum value. These phenomena explain the minimum radial force acting on the impeller. The findings of this study can provide a useful reference for the design of centrifugal pumps.

scholarly journals Multicondition Optimization and Experimental Measurements of a Double-Blade Centrifugal Pump Impeller

2012 ◽  
Vol 135 (1) ◽  
Author(s):  
Houlin Liu ◽  
Kai Wang ◽  
Shouqi Yuan ◽  
Minggao Tan ◽  
Yong Wang ◽  
...  
Keyword(s):  
Objective Function ◽  
Flow Rate ◽  
Performance Characteristic ◽  
Weighted Average ◽  
Design Flow ◽  
Meridional Plane ◽  
Original Design ◽  
Piv Measurements ◽  
Average Efficiency ◽  
Design Flow Rate

In order to improve internal unsteady flow in a double-blade centrifugal pump (DBCP), this study used major geometric parameters of the original design as the initial values, heads at three conditions (i.e., 80% design flow rate, 100% design flow rate, and 120% design flow rate) as the constraints conditions, and the maximum of weighted average efficiency at the three conditions as the objective function. An adaptive simulated annealing algorithm was selected to solve the energy performance calculation model and the supertransitive approximation method was applied to fix optimal weight factors of individual objectives. On the basis of hydraulic performance optimization, three-condition automatic computational fluid dynamics (CFD) optimization of impeller meridional plane for the DBCP was realized by means of Isight software integrated Pro/E, Gambit, and Fluent software. The shroud arc radii R0 and R1, shroud angle T1, hub arc radius R2, and hub angle T2 on the meridional plane were selected as the design variables and the maximum of weighted average hydraulic efficiency at the three conditions was chosen as the objective function. Performance characteristic test and particle image velocimetry (PIV) measurements of internal flow in the DBCP were conducted. Performance characteristic test results show that the weighted average efficiency of the impeller after the three-condition optimization has increased by 1.46% than that of original design. PIV measurements results show that vortex or recirculation phenomena in the impeller are distinctly improved under the three conditions.

Turbulence Measurements in a Centrifugal Pump With a Synchronously Orbiting Impeller

1991 ◽  
Author(s):  
Ronald D. Flack ◽  
Steven M. Miner ◽  
Ronald J. Beaudoin
Keyword(s):  
Centrifugal Pump ◽  
Reynolds Stress ◽  
Flow Rate ◽  
Cross Product ◽  
Design Flow ◽  
Low Flow ◽  
Rate Variation ◽  
Flow Rates ◽  
The Individual ◽  
Design Flow Rate

Turbulence profiles were measured in a centrifugal pump with an impeller with backswept blades using a two directional laser velocimeter. Data presented includes radial, tangential, and cross product Reynolds stresses. Blade to blade profiles were measured at four circumferential positions and four radii within and one radius outside the four bladed impeller. The pump was tested in two configurations; with the impeller running centered within the volute, and with the impeller orbiting with a synchronous motion (ε/r2 = 0.016). Flow rates ranged from 40% to 106% of the design flow rate. Variation in profiles among the individual passages in the orbiting impeller were found. For several regions the turbulence was isotropic so that the cross product Reynolds stress was low. At low flow rates the highest cross product Reynolds stress was near the exit. At near design conditions the lowest cross product stress was near the exit, where uniform flow was also observed. Also, near the exit of the impeller the highest turbulence levels were seen near the tongue. For the design flow rate, inlet turbulence intensities were typically 9% and exit turbulence intensities were 6%. For 40% flow capacity the values increased to 18% and 19%, respectively. Large local turbulence intensities correlated with separated regions. The synchronous orbit did not increase the random turbulence, but did affect the turbulence in the individual channels in a systematic pattern.

Sign in / Sign up

Export Citation Format

Share Document