scholarly journals Low Temperature One-Pot Hydrothermal Carbonization of Corn Straw into Hydrochar for Adsorbing Cadmium (II) in Wastewater

Energies ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 8503
Author(s):  
Heng Li ◽  
Yan Shi ◽  
Li Bai ◽  
Mingshu Chi ◽  
Xiuling Xu ◽  
...  
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Hydrothermal Reaction ◽  
Agricultural Waste ◽  
Hydrothermal Carbonization ◽  
Size Analysis ◽  
Order Kinetic ◽  
Corn Straw ◽  
Pore Size Analysis

Corn straw, a typical agricultural waste, was directly converted into hydrochar with a yield of 77.56% by hydrothermal carbonization at 140–230 °C for 2 h with a solid–liquid ratio of 1:20. The morphology and surface properties were characterized by elemental analysis, specific surface area and pore size analysis and Fourier transform infrared spectroscopy. The results showed that with the increase of hydrothermal reaction temperature, some physical and chemical properties such as the increase of hydrocarbon content, crystallinity, and specific surface area of hydrochar changed significantly. A series of chemical reactions such as dehydration, decarboxylation, and aromatization occurred in the hydrothermal carbonization process so that the prepared hydrochar had rich oxygen-containing functional groups (-HO, C-O-C, C=O) and unique porous structure made the hydrochar prepared at 170 °C had the best removal effect on Cd2+ in solution (5.84 mg/g). These specific conditions could remove Cd2+ and greatly improve the adsorption performance. The pseudo-second-order kinetic model and Freundlich isotherm model could better describe the adsorption behavior of Cd2+. Therefore, corn straw hydrochar as a potential adsorbent for removing Cd2+ from water.

scholarly journals Experimental Study on Influence of Al2O3, CaO and SiO2 on Preparation of Zinc Ferrite

Minerals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 396
Author(s):  
Jinlin Yang ◽  
Shuo Xu ◽  
Wentao Zhou ◽  
Pengyan Zhu ◽  
Jiguang Liu ◽  
...  
Keyword(s):  
Specific Surface ◽  
Pore Size ◽  
Surface Area ◽  
Specific Surface Area ◽  
Zinc Ferrite ◽  
Particle Surface ◽  
Molar Ratio ◽  
Size Analysis ◽  
Sulfide Deposit ◽  
Pore Size Analysis

Gossan ore of sulfide zinc deposit contains abundant zinc, iron, and other metal elements, which is a significant resource with complex components and can be utilized. In this study, a new technology of preparing zinc ferrite from zinc sulfide deposit gossan was proposed. The effects of Al2O3, CaO, and SiO2 in gossan on the formation of zinc ferrite were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), and specific surface area and pore size analysis (BET). The results show that the presence of Al2O3 and CaO could hinder the formation of zinc ferrite, while silica had no effect on the formation of zinc ferrite. Under the conditions of the molar ratio of ZnO and Fe2O3 to Al2O3, CaO, and SiO2 of 1:1:1, an activation time of 60 min, and a roasting temperature of 750 °C for 120 min, the products, which had good crystallinity, smooth particle surface, and uniform particle size could be obtained. In addition, compared to the roasted products with Al2O3 and CaO, the specific surface area, pore volume, and pore size of the products with SiO2 were the largest.

scholarly journals Development and Characterization of Composite Carbon Adsorbents with Photocatalytic Regeneration Ability: Application to Diclofenac Removal from Water

Catalysts ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 173
Author(s):  
Velma Beri Kimbi Yaah ◽  
Satu Ojala ◽  
Hamza Khallok ◽  
Tiina Laitinen ◽  
Marcin Selent ◽  
...  
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Functional Groups ◽  
Specific Surface Area ◽  
Palm Kernel ◽  
Hydrothermal Carbonization ◽  
Carbon Composite ◽  
Carbon Adsorbents ◽  
Regeneration Ability ◽  
Activation Temperature

This paper presents results related to the development of a carbon composite intended for water purification. The aim was to develop an adsorbent that could be regenerated using light leading to complete degradation of pollutants and avoiding the secondary pollution caused by regeneration. The composites were prepared by hydrothermal carbonization of palm kernel shells, TiO2, and W followed by activation at 400 °C under N2 flow. To evaluate the regeneration using light, photocatalytic experiments were carried out under UV-A, UV-B, and visible lights. The materials were thoroughly characterized, and their performance was evaluated for diclofenac removal. A maximum of 74% removal was observed with the composite containing TiO2, carbon, and W (HCP25W) under UV-B irradiation and non-adjusted pH (~5). Almost similar results were observed for the material that did not contain tungsten. The best results using visible light were achieved with HCP25W providing 24% removal of diclofenac, demonstrating the effect of W in the composite. Both the composites had significant amounts of oxygen-containing functional groups. The specific surface area of HCP25W was about 3 m2g−1, while for HCP25, it was 160 m2g−1. Increasing the specific surface area using a higher activation temperature (600 °C) adversely affected diclofenac removal due to the loss of the surface functional groups. Regeneration of the composite under UV-B light led to a complete recovery of the adsorption capacity. These results show that TiO2- and W-containing carbon composites are interesting materials for water treatment and they could be regenerated using photocatalysis.

scholarly journals New Electrodes Prepared from Mineral and Plant Raw Materials of Kazakhstan

2016 ◽  
Vol 18 (2) ◽  
pp. 141 ◽  
Author(s):  
A.A. Atchabarova ◽  
R.R. Tokpayev ◽  
A.T. Kabulov ◽  
S.V. Nechipurenko ◽  
R.A. Nurmanova ◽  
...  
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Electrode Materials ◽  
Raw Materials ◽  
Hydrothermal Carbonization ◽  
Walnut Shell ◽  
High Background ◽  
Plant Raw Materials ◽  
Developed Surface

<p>Electrode materials were prepared from activated carbonizates of walnut shell, apricot pits and shungite rock from “Bakyrchik” deposit, East Kazakhstan. Physicochemical characteristics of the obtained samples were studied by the Brunauer-Emett-Taylor method, scanning electron microscopy, Raman spectroscopy and other methods. Electrochemical properties of the obtained materials were studied by the method of cyclic voltammetry. It was found that the samples have an amorphous structure. Samples based on plant raw materials after hydrothermal carbonization at 240 °С during 24 h, have more homogeneous and developed surface. Specific surface area of carbon containing materials based on apricot pits is 1300 m<sup>2</sup>/g, for those on the based on mineral raw material, it is 153 m<sup>2</sup>/g. It was shown that materials after hydrothermal carbonization can be used for catalytic purposes and electrodes after thermal carbonization for analytical and electrocatalytic purposes. Electrode obtained by HTC have electrocatalytic activity. CSC 240 has high background current (slope i/Е is 43 mА V<sup>–1</sup> cm<sup>–2</sup>), low potential of the hydrogen electroreduction (more positive by ~ 0.5 V than samples based on plant raw materials). The reaction of DA determination is more pronounced on the electrodes obtained by HTC 240 °C, 24 h, due to the nature, carbon structure and high specific surface area of obtained samples.</p>

Facile Preparation of Iron-Manganese Oxide@Diatomite Composite for Effective Removal of Vanadium from Wastewater

2019 ◽  
Vol 72 (9) ◽  
pp. 717
Author(s):  
Junying Song ◽  
Zhanbin Huang ◽  
Fengzhi Yang
Keyword(s):  
Specific Surface ◽  
Manganese Oxide ◽  
Surface Area ◽  
Specific Surface Area ◽  
Photoelectron Spectroscopy ◽  
Pore Volume ◽  
Low Cost ◽  
Order Kinetic ◽  
Environmental Friendliness ◽  
Iron Manganese

Excess pentavalent vanadium(v) has severely degraded water quality and posed a huge threat to human health over the past several decades. Hence, it’s urgent and significant to explore a novel adsorbent which is low cost and efficient to treat vanadium pollution. In this work, a novel iron-manganese oxide@diatomite (MnFe2O4@DE) adsorbent with superior removal performance for simulated vanadium(v) wastewater was synthesised via a facile hydrothermal method. The as-prepared MnFe2O4@DE composite was characterised through different characterisation techniques. The results indicated that the MnFe2O4 nanoparticles were uniformly deposited on the surface of diatomite, resulting in a larger specific surface area and pore volume of the composite. In addition, the MnFe2O4@DE adsorbent exhibited the highest adsorption capacity for vanadium(v) (18.37mgg−1±0.5%), which was up to around 13.24 and 1.33 times as much as that of pure diatomite and MnFe2O4, respectively. This is mainly attributed to the enhanced specific surface area and pore volume. Furthermore, X-ray photoelectron spectroscopy (XPS) analysis demonstrated vanadium(v) could be reduced to low valence vanadium with low toxicity by the MnFe2O4@DE composite which could exist as VO2+ and VO+ cations in solution. The adsorption process was better fitted with a pseudo-second-order kinetic model and Langmuir model, which is spontaneous and endothermic. Overall, the novel MnFe2O4@DE composite could be applied as a promising adsorbent in addressing vanadium pollution issues due to its properties of low cost, effectiveness, and environmental friendliness.

scholarly journals PHYSICOCHEMICAL PROPERTIES AND POZZOLANIC PERFORMANCE OF ULTRAFINE TREATED RICE HUSK ASH (UFTRHA) AS ADDITIVE IN CONCRETE

2018 ◽  
Vol 16 ◽  
Author(s):  
Siti Asmahani Saad ◽  
Nasir Shafiq ◽  
Maisarah Ali
Keyword(s):  
Particle Size ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Rice Husk ◽  
Amorphous Silica ◽  
Rice Husk Ash ◽  
High Energy ◽  
Size Analysis ◽  
Pre Treatment

Rice husk ash (RHA) contains high amount of amorphous silica that is ubiquitous in the pozzolanic reaction of SCM in concrete. However, usage of conventional RHA is currently unfavourable in concrete industry due to its properties inconsistency. In this regard, improvement on the RHA properties by introduction of thermochemical pre-treatment prior to burning procedure is seen as an excellent way to reach the goal. In this paper, raw rice husk was pre-treated using 0.1N hydrochloric acid (HCl) and heated at 80oC. It was then mechanically activated by high energy planetary ball mill for 15 minutes at speed of 300rpmand ball-to-powder ratio (BPR) of 15:1. The chemical composition, mineralogical properties, particle size analysis, specific surface area as well as microstructure properties of ultrafine treated rice husk ash (UFTRHA) were determined accordingly. As for amorphous silica content of the optimum sample was recorded as 98.60% incinerated at 600oC with four hours of pre-treatment soaking duration. In terms of particle size and specific surface, it was also observed that, burning temperature of 600oC, pre-treated at four hours were recorded to produce finest size of UFTRHA where d(0.1), d(0.5) and d(0.9) were obtained as 1.416?m, 4.364 ?m and 14.043 ?m respectively. Largest specific surface area value was obtained at 219.58 m2/g with the similar pre-treatment conditions. Meanwhile, the strength activity of UFTRHA from the optimum pre-treatment process was measured by testing the compressive strength of mortars. The highest compression value obtained was 50.17MPa with 3% UFTRHA replacement at 28 days.

scholarly journals Ultrasound-Assisted Hydrazine Reduction Method for the Preparation of Nickel Nanoparticles, Physicochemical Characterization and Catalytic Application in Suzuki-Miyaura Cross-Coupling Reaction

Nanomaterials ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 632
Author(s):  
Adél Anna Ádám ◽  
Márton Szabados ◽  
Gábor Varga ◽  
Ádám Papp ◽  
Katalin Musza ◽  
...  
Keyword(s):  
Low Power ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Physicochemical Characterization ◽  
Coupling Reaction ◽  
Cross Coupling ◽  
Hydrazine Reduction ◽  
Cross Coupling Reaction ◽  
Pore Size Analysis

In the experimental work leading to this contribution, the parameters of the ultrasound treatment (temperature, output power, emission periodicity) were varied to learn about the effects of the sonication on the crystallization of Ni nanoparticles during the hydrazine reduction technique. The solids were studied in detail by X-ray diffractometry, dynamic light scattering, thermogravimetry, specific surface area, pore size analysis, temperature-programmed CO2/NH3 desorption and scanning electron microscopy. It was found that the thermal behaviour, specific surface area, total pore volume and the acid-base character of the solids were mainly determined by the amount of the nickel hydroxide residues. The highest total acidity was recorded over the solid under low-power (30 W) continuous ultrasonic treatment. The catalytic behaviour of the nanoparticles was tested in a Suzuki-Miyaura cross-coupling reaction over five samples prepared in the conventional as well as the ultrasonic ways. The ultrasonically prepared catalysts usually performed better, and the highest catalytic activity was measured over the nanoparticles prepared under low-power (30 W) continuous sonication.

Size Analysis Based on Sorption Study Data for Hydroxyapatite Nanoparticles

2021 ◽  
Vol 1031 ◽  
pp. 172-177
Author(s):  
Evgeniya Maraeva ◽  
Kamilya Khalugarova
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Chemical Deposition ◽  
Study Data ◽  
Size Analysis ◽  
Hydroxyapatite Nanoparticles ◽  
Sorption Method ◽  
Sorption Study

This work is devoted to the study on the possibility of applying the method of analyzing the particle size of hydroxyapatite at various stages of synthesis. A series of hydroxyapatite powders obtained by chemical deposition using microwave radiation is considered. Determination of the size of hydroxyapatite nanorods is carried out on the basis of data on the density and specific surface area. The specific surface area is analyzed by the sorption method. Determination of the ratio "length / diameter" of nanorods is based on the analysis of images obtained by scanning electron microscopy.

Preparation and Adsorption Properties of Rod MgNiAl-LDH

2019 ◽  
Vol 956 ◽  
pp. 294-304
Author(s):  
Guo Jun Ke ◽  
Hong Jun Tan ◽  
Peng Fei Yang ◽  
Pin Yu Zou
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Raw Materials ◽  
Magnesium Nitrate ◽  
Chloride Ions ◽  
Adsorption Properties ◽  
Order Kinetic ◽  
Nickel Aluminum ◽  
Order Kinetic Model

Using magnesium nitrate, nickel nitrate and aluminum nitrate as raw materials and urea as precipitant, magnesium nickel aluminum ternary hydrotalcites with large specific surface area were prepared by hydrothermal method. The prepared samples were characterized by SEM、XRD、BET and EDS etc., respectively. The adsorption properties of MgNiAl-LDHs, MgAl-LDHs and their calcined products (MgNiAl-LDOs, MgAl-LDOs) for chloride ions in solution were investigated. The results show that MgNiAl-LDHs are cubic with rod-like structure, with a specific surface area of 197.62 m2/g, which is much larger than that of MgAl-LDHs (102.82 m2/g). Under the same adsorption conditions, the saturated adsorption capacities of MgNiAl-LDHs and MgAl-LDHs for chloride ions are 130.06mg/g and 110.02 mg/g respectively. MgNiAl-LDOs showed better adsorption ability for chloride ions. By simulating the adsorption data, the results show that the adsorption kinetics and the adsorption isotherm are in accordance with the quasi-second-order kinetic model and the Langmuir isotherm model, respectively.

Study on Microstructure Variation Laws of Al-Pillared Montmorillonite

2010 ◽  
Vol 158 ◽  
pp. 248-255 ◽  
Author(s):  
Gui Fang Wang ◽  
Xian Jun Lu ◽  
Shuai Zhang ◽  
Shao Jian Ma ◽  
Jun Qiu ◽  
...  
Keyword(s):  
Specific Surface ◽  
Pore Size ◽  
Surface Area ◽  
Specific Surface Area ◽  
Interlayer Spacing ◽  
Volume Distribution ◽  
Pillared Montmorillonite ◽  
Bet Specific Surface Area ◽  
Pore Size Analysis ◽  
Porous Volume

Al3+/clay ratio is one of the important factors influencing microstructure of Al-pillared montmorillonite. Microstructure variation laws of Al-pillared montmorillonite prepared under the condition of different Al3+/clay ratio are systematically studied by XRD, FTIR, specific surface area and pore size analysis. The results show that the interlayer spacing and BET specific surface area of Al-pillared montmorillonite are remarkably affected by the Al3+/clay ratio. The interlayer spacing d(001) value and BET specific surface area of Al-pillared montmorillonite increase firstly and then decrease with the increases of the Al3+/clay ratio, and they reach to maximum when the Al3+/clay ratio is 10mmol/g. Besides, the BJH porous volume distribution of Al-pillared montmorillonite is the most probable distribution, and the most probable pore size is about 2 nm, which is attributed to mesopore. The porous structure of hydroxy-Al pillared montmorillonite is characterized as parallel plate slit or “house-of-cards” wedge-shaped pore which is formed by novel meso-microporous delaminated structure and fragments. With the increase of the Al3+/clay ratio, BJH total porous volume and mesoporous volume of hydroxy-Al pillared montmorillonite decreases, while the proportion of microporous volume in the total porous volume increases. The proportion of microporous specific surface area of all the hydroxy-Al pillared montmorillonite samples is about 62% and is much larger than that of Na-M and those of mesopore and macropore, indicating the main action of intercalation of hydroxy-Al pillaring solution into montmorillonite interlayer is to increase the micropore amount.

Sign in / Sign up

Export Citation Format

Share Document