scholarly journals Identification of the Physical and Mechanical Properties of Moroccan Sisal Yarns Used as Reinforcements for Composite Materials

Fibers ◽  
2021 ◽  
Vol 9 (2) ◽  
pp. 13
Author(s):  
Zineb Samouh ◽  
Omar Cherkaoui ◽  
Damien Soulat ◽  
Ahmad Rashed Labanieh ◽  
François Boussu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Contact Angle ◽  
Thermal Properties ◽  
Elastic Modulus ◽  
Composite Materials ◽  
Twist Angle ◽  
Physical And Mechanical Properties ◽  
Sisal Fiber ◽  
Method Show

This work aims to investigate the physical and mechanical properties of sisal fiber and yarn of Moroccan origin. The cellulosic and non-cellulosic constituents of the Moroccan sisal fiber were identified by FTIR spectroscopy. The thermal properties were studied by thermogravimetric analysis. The hydrophilicity of the fiber was evaluated by the contact angle. The results show that the sisal fiber has a low thermal stability. The mechanical properties of the fiber analyzed by the Impregnated Fiber Bundle Test (IFBT) method show that the porosity of the impregnated yarns and the twist angle of the yarns influence the elastic modulus of the sisal fiber. The physical and mechanical properties of the manufactured sisal yarns were also characterized and analyzed. The obtained results reveal an interesting potential to use the Moroccan sisal fiber in development of bio-sourced composite materials.

Effect of Wood Filler Concentration on Physical and Mechanical Properties of PLA-Based Composites

2021 ◽  
Vol 887 ◽  
pp. 110-115
Author(s):  
G.A. Sabirova ◽  
R.R. Safin ◽  
N.R. Galyavetdinov
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Composite Materials ◽  
Impact Strength ◽  
Wood Flour ◽  
Experimental Studies ◽  
Physical And Mechanical Properties ◽  
Filler Concentration ◽  
High Concentration

This paper presents the findings of experimental studies of the physical and mechanical properties of wood-filled composites based on polylactide (PLA) and vegetable filler in the form of wood flour (WF) thermally modified at 200-240 °C. It also reveals the dependence of the tensile strength, impact strength, bending elastic modulus, and density of composites on the amount of wood filler and the temperature of its thermal pre-modification. We established that an increase in the concentration of the introduced filler and the degree of its heat treatment results in a decrease of the tensile strength, impact strength and density of composite materials, while with a lower binder content, thermal modification at 200 °C has a positive effect on bending elastic modulus. We also found that 40 % content of a wood filler heated to 200 °C is sufficient to maintain relatively high physical and mechanical properties of composite materials. With a higher content of a wood filler, the cost can be reduced but the quality of products made of this material may significantly deteriorate. However, depending on the application and the life cycle of this product, it is possible to develop a formulation that includes a high concentration of filler.

scholarly journals Physical and Mechanical Properties of Natural Leaf Fiber-Reinforced Epoxy Polyester Composites

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1369
Author(s):  
Sanjeev Kumar ◽  
Lalta Prasad ◽  
Vinay Kumar Patel ◽  
Virendra Kumar ◽  
Anil Kumar ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Synthetic Fibre ◽  
Low Cost ◽  
Fibre Length ◽  
Physical And Mechanical Properties ◽  
Natural Fibres ◽  
Risk Environment ◽  
Insulation Property ◽  
Natural Leaf

In recent times, demand for light weight and high strength materials fabricated from natural fibres has increased tremendously. The use of natural fibres has rapidly increased due to their high availability, low density, and renewable capability over synthetic fibre. Natural leaf fibres are easy to extract from the plant (retting process is easy), which offers high stiffness, less energy consumption, less health risk, environment friendly, and better insulation property than the synthetic fibre-based composite. Natural leaf fibre composites have low machining wear with low cost and excellent performance in engineering applications, and hence established as superior reinforcing materials compared to other plant fibres. In this review, the physical and mechanical properties of different natural leaf fibre-based composites are addressed. The influences of fibre loading and fibre length on mechanical properties are discussed for different matrices-based composite materials. The surface modifications of natural fibre also play a crucial role in improving physical and mechanical properties regarding composite materials due to improved fibre/matrix adhesion. Additionally, the present review also deals with the effect of silane-treated leaf fibre-reinforced thermoset composite, which play an important role in enhancing the mechanical and physical properties of the composites.

scholarly journals High modulus polyimide particle-reinforcement of epoxy composites

2021 ◽  
Author(s):  
Johannes Essmeister ◽  
M. Josef Taublaender ◽  
Thomas Koch ◽  
D. Alonso Cerrón-Infantes ◽  
Miriam M. Unterlass ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Composite Materials ◽  
Epoxy Matrix ◽  
Epoxy Composites ◽  
High Modulus ◽  
Particle Reinforcement

A novel class of fully organic composite materials with well-balanced mechanical properties and improved thermal stability was developed by incorporating highly crystalline, hydrothermally synthesized polyimide microparticles into an epoxy matrix.

scholarly journals Effect of Structural Differences on the Mechanical Properties of 3D Integrated Woven Spacer Sandwich Composites

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4284
Author(s):  
Lvtao Zhu ◽  
Mahfuz Bin Rahman ◽  
Zhenxing Wang
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Three Dimensional ◽  
Sheet Thickness ◽  
Physical And Mechanical Properties ◽  
Sandwich Composites ◽  
Computed Tomography Images ◽  
And Performance ◽  
Industrial Textiles ◽  
Load Conditions

Three-dimensional integrated woven spacer sandwich composites have been widely used as industrial textiles for many applications due to their superior physical and mechanical properties. In this research, 3D integrated woven spacer sandwich composites of five different specifications were produced, and the mechanical properties and performance were investigated under different load conditions. XR-CT (X-ray computed tomography) images were employed to visualize the microstructural details and analyze the fracture morphologies of fractured specimens under different load conditions. In addition, the effects of warp and weft direction, face sheet thickness, and core pile height on the mechanical properties and performance of the composite materials were analyzed. This investigation can provide significant guidance to help determine the structure of composite materials and design new products according to the required mechanical properties.

Expanded vermiculite-filled flexible polymer composites

2021 ◽  
pp. 009524432110290
Author(s):  
Mukaddes Sevval Cetin ◽  
Ozan Toprakci ◽  
Omer Suat Taskin ◽  
Abdullah Aksu ◽  
Hatice Aylin Karahan Toprakci
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Contact Angle ◽  
Polymer Composites ◽  
Flame Retardancy ◽  
Composite Films ◽  
Filler Concentration ◽  
High Shear ◽  
Flexible Polymer ◽  
Shear Mixing

This study focuses on the fabrication and characterization of vermiculite-filled flexible polymer composites. Exfoliated vermiculite was incorporated into triblock thermoplastic elastomer copolymer, styrene- b-(ethylene- co-butylene)- b-styrene (SEBS), at various levels from 1 to 15 wt% by a high shear mixer. The composite films were obtained by the combination of solvent casting and compression molding. The morphological, structural, thermal, and mechanical properties and contact angle of the composites were determined. Some micro-morphological differences were observed between the samples and the difference was assumed to be caused by high shear mixing and filler concentration. High shear mixing was found effective in terms of the detachment of vermiculite layers at all concentrations. However, at low filler loading, that behavior was more obvious. At 1 wt% filler concentration, mechanical properties increased that was probably caused by good filler-matrix interaction stemmed from smaller particle size. At higher vermiculite concentrations, fillers found to show agglomerations that led to a decrease in mechanical strength and strain at break. Elastic and secant modulus showed an increasing trend. Contact angle measurements were carried out to determine the oleophilic character of the samples. An increase in the vermiculite content resulted in higher oleophilic character and the lowest contact angle was obtained at 15 wt% VMT loading. In addition to these, thermal stability, thermal dimensional stability and flame retardancy were improved by the incorporation of VMT. 15 wt% vermiculite-filled sample showed the best performance in terms of thermal stability and flame retardancy.

scholarly journals METHOD OF SAMPLE MANUFACTURING FROM MULTILAYER COMPOSITE MATERIALS FOR STUDYING THEIR MECHANICAL PROPERTIES

2018 ◽  
pp. 16-23
Author(s):  
Alsaid Mazen ◽  
Ali Salamekh
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Polymer Composite ◽  
Testing Machine ◽  
Physical And Mechanical Properties ◽  
Polymer Composite Materials ◽  
Technological Parameters ◽  
Cutting Out ◽  
Method Of Production ◽  
Economic Considerations

In the last decades there is increasing the need to apply polymer composite materials in different industries, particularly in shipbuilding. There are developing single structures made from polymer composite materials to be used on board ships. The article focuses on technology of manufacturing slabs from polymer composite materials to carry out mechanical testing in the laboratory special standard units. Mechanical properties of polymer composite materials depend on molding technologies. There has been described a technology of sample manufacturing from polymer composite materials reinforced with glass fiber mat with fiberglass plastics. The technique of testing the specified samples for tensile strength has been considered. The sizes and shapes of the samples as well as the technological parameters of the manufacturing process have been validated, depending on the standard requirements and the technological features of the testing machine. The physical and mechanical properties of the components that make up the composite materials are considered. The sequence of stacking layers for preparation of plates from composite materials is indicated. The dimensions of the plates for cutting out finished samples are determined, depending on the method of production. The way of laying plates from composite materials has been chosen on the base of economic considerations and conditions of accessibility. The obtained results of mechanical properties can be used in solving problems of application of polymer composite materials in shipbuilding, for example, in manufacturing superstructures of some dry cargo vessels.

The influence of functionalization time of carbon nanotube on the mechanical properties of the epoxy composites

2017 ◽  
Vol 51 (12) ◽  
pp. 1693-1701 ◽  
Author(s):  
EA Zakharychev ◽  
EN Razov ◽  
Yu D Semchikov ◽  
NS Zakharycheva ◽  
MA Kabina
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Carbon Nanotube ◽  
Composite Materials ◽  
Polymer Composites ◽  
Epoxy Composites ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

This paper investigates the structure, length, and percentage of functional groups of multi-walled carbon nanotubes (CNT) depending on the time taken for functionalization in HNO3 and H2SO4 mixture. The carbon nanotube content and influence of functionalization time on mechanical properties of polymer composite materials based on epoxy matrix are studied. The extreme dependencies of mechanical properties of carbon nanotube functionalization time of polymer composites were established. The rise in tensile strength of obtained composites reaches 102% and elastic modulus reaches 227% as compared to that of unfilled polymer. The composites exhibited best mechanical properties by including carbon nanotube with 0.5 h functionalization time.

METAL COMPOSITE MATERIALS BASED ON TITANIUM ALLOYS, REINFORCED WITH REFRACTORY PARTICLES (review)

2021 ◽  
pp. 36-45
Author(s):  
E.I. Krasnov ◽  
◽  
V.M. Serpova ◽  
L.G. Khodykin ◽  
A.V. Gololobov ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Composite Materials ◽  
Literature Review ◽  
Titanium Alloys ◽  
Chemical Nature ◽  
Physical And Mechanical Properties ◽  
Metal Composite ◽  
The Matrix ◽  
Metal Composite Materials

Presents a literature review in the field of methods for strengthening titanium and its alloys by introducing various refractory particles into the matrix. The main problematic issues related to the chemical nature of refractory particles and titanium alloys that arise during hardening are briefly described. The main structural, physical and mechanical properties and morphology of such metal composite materials are described. The dependence of the influence of various refractory particles and their amount, as well as the effect of heat treatment on the physical and mechanical properties of microns based on titanium alloys, is presented.

Comparative experimental study on physical and mechanical properties of quartz sandstone after water-cooling and natural-cooling under high temperature

2021 ◽  
pp. qjegh2020-181
Author(s):  
Haopeng Jiang ◽  
Annan Jiang ◽  
Fengrui Zhang
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Uniaxial Compressive Strength ◽  
Heating Temperature ◽  
Physical And Mechanical Properties ◽  
P Wave ◽  
Water Cooling ◽  
Average Value ◽  
Cooling Methods

Experimental tests were conducted to study the influence of natural cooling and water cooling on the physical and mechanical properties of quartz sandstone. This study aims to understand the effect of different cooling methods on the physical and mechanical properties of quartz sandstone (such as mass, volume, density, P-wave velocity, elastic modulus, uniaxial compressive strength, etc.). The results show that the uniaxial compressive strength (UCS) and elastic modulus(E) of the specimens cooled by natural-cooling and water-cooling decrease with heating temperature. At 800℃, after natural cooling and water cooling, the average value of UCS decreased by 34.65% and 57.90%, and the average value of E decreased by 87.66% and 89.05%, respectively. Meanwhile, scanning electron microscope (SEM) images were used to capture the development of microcracks and pores within the specimens after natural-cooling and water-cooling, and it was found that at the same temperature, water cooling treatment was more likely to cause microcracks and pores, which can cause more serious damage to the quartz sandstone. These results confirm that different cooling methods have different effects on the physical and mechanical properties of quartz sandstone, and provide a basis for the stability prediction of rock mass engineering such as tunnel suffering from fire.

Sign in / Sign up

Export Citation Format

Share Document