scholarly journals The Use of Composite Materials in 3D Printing

2020 ◽  
Vol 4 (2) ◽  
pp. 42 ◽  
Author(s):  
Ignazio Blanco
Keyword(s):  
Composite Materials ◽  
3D Printing ◽  
Rapid Prototyping ◽  
Polymer Matrix ◽  
Chemical Properties ◽  
Modified Polymer ◽  
Research Activities ◽  
Physico Chemical ◽  
3D Printed ◽  
Limited Spectrum

Nowadays, all production, from the smallest ones to large companies, and research activities are affected by the use of 3D printing technology. The major limitation, in order to cover as many fields of application as possible, is represented by the set of 3D printable materials and their limited spectrum of physico-chemical properties. To expand this spectrum and employ the 3D-printed objects in areas such as biomedical, mechanical, electronical and so on, the introduction of fibers or particles in a polymer matrix has been widely studied and applied. In this review, all those studies that proposed modified polymer presenting advantages associated with rapid prototyping are reported.

Mechanical Properties of 3D-Printed Wood-Plastic Composites

2018 ◽  
Vol 777 ◽  
pp. 499-507 ◽  
Author(s):  
Ossi Martikka ◽  
Timo Kärki ◽  
Qing Ling Wu
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
3D Printing ◽  
Impact Strength ◽  
Polylactic Acid ◽  
Wood Plastic Composite ◽  
Wood Plastic Composites ◽  
Plastic Composite ◽  
Plastic Composites ◽  
3D Printed

3D printing has rapidly become popular in both industry and private use. Especially fused deposition modeling has increased its popularity due to its relatively low cost. The purpose of this study is to increase knowledge in the mechanical properties of parts made of wood-plastic composite materials by using 3D printing. The tensile properties and impact strength of two 3D-printed commercial wood-plastic composite materials are studied and compared to those made of pure polylactic acid. Relative to weight –mechanical properties and the effect of the amount of fill on the properties are also determined. The results indicate that parts made of wood-plastic composites have notably lower tensile strength and impact strength that those made of pure polylactic acid. The mechanical properties can be considered sufficient for low-stress applications, such as visualization of prototypes and models or decorative items.

scholarly journals Novel 3D-Printed MEMS Magnetometer with Optical Detection

Proceedings ◽  
2018 ◽  
Vol 2 (13) ◽  
pp. 783 ◽  
Author(s):  
Matthias Kahr ◽  
Wilfried Hortschitz ◽  
Harald Steiner ◽  
Michael Stifter ◽  
Andreas Kainz ◽  
...  
Keyword(s):  
3D Printing ◽  
Product Development ◽  
Rapid Prototyping ◽  
Low Cost ◽  
High Accuracy ◽  
Structural Performance ◽  
Sensitivity Measurement ◽  
Optical Readout ◽  
3D Printed ◽  
Working Principle

This paper reports a novel 3D printed MEMS magnetometer with optical readout, which demonstrates the advantages of 3D printing technology in terms of rapid prototyping. Low-cost and fast product development cycles favour 3D printing as an effective tool. Sensitivity measurement with such devices indicate high accuracy and good structural performance, considering material and technological uncertainties. This paper is focusing on the novelty of the rapid, 3D-printing prototyping approach and verification of the working principle for printed MEMS magnetometers.

scholarly journals Wet-chemical method for the metallization of a para-aramid filament yarn wound on a cylindrical dyeing package

2016 ◽  
Vol 87 (10) ◽  
pp. 1192-1202 ◽  
Author(s):  
Toty Onggar ◽  
Gosbert Amrhein ◽  
Anwar Abdkader ◽  
Rolf-Dieter Hund ◽  
Chokri Cherif
Keyword(s):  
Composite Materials ◽  
High Performance ◽  
Glass Fibers ◽  
Chemical Properties ◽  
Filament Yarn ◽  
Silver Layer ◽  
Physico Chemical ◽  
Before And After ◽  
Physical Examinations ◽  
Wet Chemical

High-performance yarns such as aramid fibers are nowadays used to reinforce composite materials due to their advantageous physico-chemical properties and their low weight. They are also resistant to heat and fire. Para-aramid filament yarns (p-AFs) wound on a cylindrical dyeing package have been silvered successfully by means of a newly developed wet-chemical filament yarn metallization process on a laboratory scale. The surface morphology of untreated and silvered p-AF was determined by means of scanning electron microscopy. The chemical structure of the surfaces (contents of carbon, oxygen, nitrogen and silver) was determined by means of energy-dispersive X-ray spectroscopy (EDX). The eliminated and newly formed groups of p-AF before and after silvering were detected by infrared spectroscopy (Fourier transform—attenuated total reflectance). After metallization, the silver layer thickness, the mass-related silver content and washing and rubbing fastness were assessed. Furthermore, textile-physical examinations concerning Young's modulus, elongation at break and electrical conductivity were performed. Subsequently, the electrically conductive p-AFs were integrated in thermoset composite materials reinforced by glass fibers and para-aramid.

scholarly journals Development and Evaluation of Amorphous Oral Thin Films Using Solvent-Free Processes: Comparison between 3D Printing and Hot-Melt Extrusion Technologies

Pharmaceutics ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1613
Author(s):  
Jiaxiang Zhang ◽  
Anqi Lu ◽  
Rishi Thakkar ◽  
Yu Zhang ◽  
Mohammed Maniruzzaman
Keyword(s):  
Thin Films ◽  
3D Printing ◽  
Drug Release ◽  
Hot Melt Extrusion ◽  
Dosage Forms ◽  
Solvent Free ◽  
Melt Extrusion ◽  
Physico Chemical ◽  
3D Printed ◽  
Hot Melt

Conventional oral dosage forms may not always be optimal especially for those patients suffering from dysphasia or difficulty swallowing. Development of suitable oral thin films (OTFs), therefore, can be an excellent alternative to conventional dosage forms for these patient groups. Hence, the main objective of the current investigation is to develop oral thin film (OTF) formulations using novel solvent-free approaches, including additive manufacturing (AM), hot-melt extrusion, and melt casting. AM, popularly recognized as 3D printing, has been widely utilized for on-demand and personalized formulation development in the pharmaceutical industry. Additionally, in general active pharmaceutical ingredients (APIs) are dissolved or dispersed in polymeric matrices to form amorphous solid dispersions (ASDs). In this study, acetaminophen (APAP) was selected as the model drug, and Klucel™ hydroxypropyl cellulose (HPC) E5 and Soluplus® were used as carrier matrices to form the OTFs. Amorphous OTFs were successfully manufactured by hot-melt extrusion and 3D printing technologies followed by comprehensive studies on the physico-chemical properties of the drug and developed OTFs. Advanced physico-chemical characterizations revealed the presence of amorphous drug in both HME and 3D printed films whereas some crystalline traces were visible in solvent and melt cast films. Moreover, advanced surface analysis conducted by Raman mapping confirmed a more homogenous distribution of amorphous drugs in 3D printed films compared to those prepared by other methods. A series of mathematical models were also used to describe drug release mechanisms from the developed OTFs. Moreover, the in vitro dissolution studies of the 3D printed films demonstrated an improved drug release performance compared to the melt cast or extruded films. This study suggested that HME combined with 3D printing can potentially improve the physical properties of formulations and produce OTFs with preferred qualities such as faster dissolution rate of drugs.

scholarly journals Property Analysis of Photo-Polymerization-Type 3D-Printed Structures Based on Multi-Composite Materials

2021 ◽  
Vol 11 (18) ◽  
pp. 8545
Author(s):  
So-Ree Hwang ◽  
Min-Soo Park
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Composite Materials ◽  
3D Printing ◽  
Bending Test ◽  
3D Printer ◽  
Complex Structures ◽  
Photo Polymerization ◽  
Anisotropic Structures ◽  
3D Printed

Additive manufacturing, commonly called 3D printing, has been studied extensively because it can be used to fabricate complex structures; however, polymer-based 3D printing has limitations in terms of implementing certain functionalities, so it is limited in the production of conceptual prototypes. As such, polymer-based composites and multi-material 3D printing are being studied as alternatives. In this study, a DLP 3D printer capable of printing multiple composite materials was fabricated using a movable separator and structures with various properties were fabricated by selectively printing two composite materials. After the specimen was fabricated based on the ASTM, the basic mechanical properties of the structure were compared through a 3-point bending test and a ball rebound test. Through this, it was shown that structures with various mechanical properties can be fabricated using the proposed movable-separator-based DLP process. In addition, it was shown that this process can be used to fabricate anisotropic structures, whose properties vary depending on the direction of the force applied to the structure. By fabricating multi-joint grippers with varying levels of flexibility, it was shown that the proposed process can be applied in the fabrication of soft robots as well.

Magnetic Field-Assisted 3D Printing of Limpet Teeth Inspired Polymer Matrix Composite With Compression Reinforcement

2021 ◽  
Vol 144 (4) ◽  
Author(s):  
Dylan Joralmon ◽  
Evangeline Amonoo ◽  
Yizhen Zhu ◽  
Xiangjia Li
Keyword(s):  
Magnetic Field ◽  
3D Printing ◽  
Polymer Matrix ◽  
Mechanical Performance ◽  
Polymer Matrix Composites ◽  
Cost Effective ◽  
Industrial Applications ◽  
Mechanical Reinforcement ◽  
3D Printed ◽  
Geometric Morphology

Abstract Lightweight and cost-effective polymer matrix composites (PMCs) with extraordinary mechanical performance will be a key to the next generation of diverse industrial applications, such as aerospace, electric automobile, and biomedical devices. Limpet teeth made of mineral-polymer composites have been proved as nature’s strongest material due to the unique hierarchical architectures of mineral fiber alignment. Here, we present an approach to build limpet teeth inspired structural materials with precise control of geometric morphologies of microstructures by magnetic field-assisted 3D printing (MF-3DP). α-Iron (III) oxide-hydroxide nanoparticles (α-FeOOHs) are aligned by the magnetic field during 3D printing and aligned α-FeOOHs (aFeOOHs) bundles are further grown to aligned goethite-based bundles (aGBs) by rapid thermal treatment after printing. The mechanical reinforcement of aGBs in PMCs can be modulated by adjusting the geometric morphology and alignment of α-FeOOHs encapsulated inside the 3D printed PMCs. In order to identify the mechanical enhancement mechanism, physics-based modeling, simulation, and tests were conducted, and the results further guided the design of bioinspired goethite-based PMCs. The correlation of the geometric morphology of self-assembled α-FeOOHs, curing characteristics of α-FeOOHs/polymer composite, and process parameters were identified to establish the optimal design of goethite-based PMCs. The 3D printed PMCs with aGBs show promising mechanical reinforcement compared with PMCs without aGBs. This study opens intriguing perspectives for designing high strength 3D printed PMCs on the basis of bioinspired architectures with customized configurations.

scholarly journals AN INVESTIGATION OF THE STRUCTURAL STRENGTH OF TRANSTIBIAL SOCKETS FABRICATED USING CONVENTIONAL METHODS AND RAPID PROTOTYPING TECHNIQUES

2019 ◽  
Author(s):  
Brittany Pousett ◽  
Aimee Lizcano ◽  
Silvia Ursula Raschke
Keyword(s):  
3D Printing ◽  
Rapid Prototyping ◽  
Ultimate Strength ◽  
Stance Phase ◽  
Structural Strength ◽  
Static Strength ◽  
Strength Test ◽  
Manufacturing Method ◽  
Strength Tests ◽  
3D Printed

BACKGROUND: Rapid Prototyping is becoming an accessible manufacturing method but before clinical adoption can occur, the safety of treatments needs to be established. Previous studies have evaluated the static strength of traditional sockets using ultimate strength testing protocols outlined by the International Organization for Standardization (ISO). OBJECTIVE: To carry out a pilot test in which 3D printed sockets will be compared to traditionally fabricated sockets, by applying a static ultimate strength test. METHODOLOGY: 36 sockets were made from a mold of a transtibial socket shape,18 for cushion liners with a distal socket attachment block and 18 for locking liners with a distal 4-hole pattern. Of the 18 sockets, 6 were thermoplastic, 6 laminated composites & 6 3D printed Polylactic Acid. Sockets were aligned in standard bench alignment and placed in a testing jig that applied forces simulating individuals of different weight putting force through the socket both early and late in the stance phase. Ultimate strength tests were conducted in these conditions. If a setup passed the ultimate strength test, load was applied until failure. FINDINGS: All sockets made for cushion liners passed the strength tests, however failure levels and methods varied. For early stance, thermoplastic sockets yielded, laminated sockets cracked posteriorly, and 3D printed socket broke circumferen-tially. For late stance, 2/3 of the sockets failed at the pylon. Sockets made for locking liners passed the ultimate strength tests early in stance phase, however, none of the sockets passed for forces late in stance phase, all broke around the lock mechanism.  CONCLUSION: Thermoplastic, laminated and 3D printed sockets made for cushion liners passed the ultimate strength test protocol outlined by the ISO for forces applied statically in gait. This provides initial evidence that 3D printed sockets are statically safe to use on patients and quantifies the static strength of laminated and thermoplastic sockets. However, all set-ups of sockets made for locking liners failed at terminal stance. While further work is needed, this suggests that the distal reinforcement for thermoplastic, laminated and 3D printed sockets with distal cylindrical locks may need to be reconsidered. LAYMAN’S ABSTRACT 3D printing is a new manufacturing method that could be used to make prosthetic sockets (the part of the prosthesis connected to the individual). However, very little is known about the strength of 3D printed sockets and if they are safe to use. As Prosthetists are responsible for providing patients with safe treatments, the strength of 3D printed sockets needs to be established before they can be used in clinical practice. The strength of sockets made using current manufacturing methods was compared to those made using 3D printing. Strength was tested using the static portion of the ISO standard most applicable for this situation which outlines the forces a socket must take at 2 points in walking–when the foot is placed on the ground (early stance) and when the foot pushed off the ground (late stance). Sockets made for two prosthetic designs (cushion and locking) were tested to determine if one is safer than the other. All sockets made for cushion liners passed the standard for forces applied statically. However, different materials failed in different ways. At early stance, thermoplastic sockets yielded, laminated composite sockets cracked and 3D printed sockets broke circumferentially. At late stance other components failed 2/3 of the time before the sockets were affected. This provides initial evidence that sockets made for cushion liners are statically safe to use on patients. Sockets made for locking liners failed around the end, showing that 3D printing should not be used to create sockets with the design tested in this study. Article PDF Link: https://jps.library.utoronto.ca/index.php/cpoj/article/view/31008/24937 How to Cite: Pousett B, Lizcano A, Raschke S.U. An investigation of the structural strength of transtibial sockets fabricated using conventional methods and rapid prototyping techniques. Canadian Prosthetics & Orthotics Journal. 2019; Volume2, Issue1, No.2. DOI: https://doi.org/10.33137/cpoj.v2i1.31008 CORRESPONDING AUTHORBrittany Pousett, BSc, MSc, Certified Prosthetist,Head of Research at Barber Prosthetics Clinic,540 SE Marine Dr, Vancouver, British Colombia V5X 2T4, Canada.Email: [email protected]

scholarly journals Investigations on physico-chemical properties of TSPCU nonwoven for application as prosthetic venous valve

2021 ◽  
Vol 7 (2) ◽  
pp. 613-616
Author(s):  
Julia Schubert ◽  
Daniela Arbeiter ◽  
Andreas Götz ◽  
Kerstin Lebahn ◽  
Wolfram Schmidt ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Chemical Properties ◽  
Storage Conditions ◽  
Valve Leaflet ◽  
Venous Valve ◽  
Sem Images ◽  
Venous Valves ◽  
Prosthetic Valves ◽  
Physico Chemical ◽  
3D Printed

Abstract Electrospinning is used for producing nonwovens for medical polymer-based implants, such as prosthetic valves or covered scaffolds. In this study, nonwovens for prosthetic venous valves are investigated regarding their morphology and mechanics in physiological medium. Spinning molds were developed based on previous venous valve leaflet designs, 3D printed in different sizes and covered with electrospun nonwovens. Samples were stored in a physiological 0.9% saline at 37°C to investigate the influence of fiber rearrangement and swelling in medium for several weeks. Two different nonwovens of thermoplastic silicone-based polycarbonaturethane (TSPCU) were compared. Tensile test results show that storage in medium has a relevant influence on the mechanical properties. SEM images of TSPCU show substantially increased fiber diameters after 8 days stored in medium. After detaching the valve leaflet nonwovens from the molds, shrinkage of the material of approximately 12% was detected. A suitable valve size could be identified for joining with the stent structure into an interventional prosthetic venous valve. The results demonstrate the influence of storage conditions on the morphological and mechanical properties of electrospun TSPCU nonwovens. For development and dimensioning of venous valve leaflets, this change in mechanical behavior and possible shrinkage of the material has to be considered.

Magnetic Field Assisted 3D Printing of Limpet Teeth Inspired Polymer Matrix Composite With Compression Reinforcement

2021 ◽  
Author(s):  
Dylan Joralmon ◽  
Evangeline Amonoo ◽  
Yizhen Zhu ◽  
Xiangjia Li
Keyword(s):  
Magnetic Field ◽  
3D Printing ◽  
Polymer Matrix ◽  
Mechanical Performance ◽  
Polymer Matrix Composites ◽  
Cost Effective ◽  
Industrial Applications ◽  
Mechanical Reinforcement ◽  
3D Printed ◽  
Geometric Morphology

Abstract Lightweight and cost-effective polymer matrix composites (PMCs) with extraordinary mechanical performance will be a key to the next generation of diverse industrial applications such as aerospace, electric automobile, and biomedical devices. Limpet teeth made of mineral-polymer composites have been proved as nature’s strongest material due to the unique hierarchical architectures of mineral fiber alignment. Here, we present an approach to build limpet teeth inspired structural materials with precise control of geometric morphologies of microstructures by magnetic field-assisted 3D printing (MF-3DP). α-Iron (III) oxide-hydroxide nanoparticles (α-FeOOHs) are aligned by the magnetic field during 3D printing and aligned α-FeOOHs bundles are further grown to aligned goethite-based bundles (aGBs) by rapid thermal treatment after printing. The mechanical reinforcement of goethite-based fillers in PMCs can be modulated by adjusting the geometric morphology and alignment of mineral particles encapsulated inside the 3D printed PMCs. In order to identify the mechanical enhancement mechanism, physics-based modeling, simulation, and tests were conducted and the results further guided the design of bioinspired goethite-based PMCs. The correlation of the geometric morphology of self-assembled α-FeOOHs, curing characteristics of α-FeOOHs/polymer composite, and process parameters were identified to establish the optimal design of goethite-based PMCs. The 3D-printed PMCs with aGBs show promising mechanical reinforcement. This study opens intriguing perspectives for designing high strength 3D printed PMCs on the basis of bioinspired architectures with customized configurations.

Sign in / Sign up

Export Citation Format

Share Document