scholarly journals The Influence of Ramp Shape Parameters on Performance of Overtopping Breakwater for Energy Conversion

2020 ◽  
Vol 8 (11) ◽  
pp. 875
Author(s):  
M. A. Musa ◽  
M. F. Roslan ◽  
M. F. Ahmad ◽  
A. M. Muzathik ◽  
M. A. Mustapa ◽  
...  
Keyword(s):  
Energy Conversion ◽  
Wave Energy ◽  
Shape Parameter ◽  
Wave Energy Converter ◽  
Geometrical Parameters ◽  
Shape Parameters ◽  
Energy Converter ◽  
Wave Condition ◽  
Is Integration ◽  
Wave Discharge

Overtopping breakwater for energy conversion (OBREC) is integration between breakwater and wave energy converter (WEC) that allows incoming waves to be stored in the reservoir. The higher the overtopping amount collected in a reservoir, the greater the energy generated will be. Hence, most of the overtopping concept has attempted to maximize the inclusion of water in the reservoir by optimizing geometrical parameters, particularly the ramp angle. However, the studies corresponding to ramp shapes geometries have not been adequately reviewed. Most studies only focused on the usage of linear overtopping ramp shape. There is still limited knowledge on the influence of different ramp shape parameters towards the overtopping wave. Thus, this paper aimed to push the border of available knowledge by investigating the influence of the ramp shape parameters to the overtopping wave discharge through simulation and experimenting approaches. Seven different ramp shapes have been tested under Malaysia’s wave condition and a new ramp shape parameter allowing for maximized overtopping wave on OBREC is presented.

scholarly journals Hydrodynamic Investigation of a Dual-Cylindrical OWC Wave Energy Converter Integrated into a Fixed Caisson Breakwater

Energies ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 896 ◽  
Author(s):  
Chang Wan ◽  
Can Yang ◽  
Qinghe Fang ◽  
Zaijin You ◽  
Jing Geng ◽  
...  
Keyword(s):  
Energy Conversion ◽  
Analytical Model ◽  
Wave Energy ◽  
Velocity Potential ◽  
Wave Energy Converter ◽  
Published Data ◽  
Geometrical Parameters ◽  
Linear Potential ◽  
Energy Converter ◽  
Cylindrical Column

A fixed dual cylindrical oscillating water column (OWC) acting as a breakwater-type wave energy converter (WEC) is proposed to harvest the wave energy effectively for shallow offshore sites. An analytical model is developed to investigate the hydrodynamic characteristics and the energy capture capacity of the cylindrical OWC device in severe waves. Based on the linear potential flow theory, the analytical solutions of the velocity potential in diffraction mode are solved by matching the Eigen-function expansion technique, and the continuous conditions of the velocity potential and fluid velocity between the computational sub-domains are involved in solving the problem for determining a solution. The proposed model is verified against the published data. The effects of the wave height, the angle of chamber clapboard and the radius of the inner and outer cylindrical column on the energy conversion efficiency are investigated in this paper. To improve the energy conversion performance and obtain a faster prediction for structural optimization of the cylindrical OWC, the geometrical parameters are further discussed in the analytical model. The results indicate that the geometrical parameters of the chamber have significant effects on the wave energy absorption efficiency. It is found that the effective frequency bandwidth of the dual cylindrical column can be broadened by improving the angle of the chamber clapboard and the inner–outer cylinder diameter ratio.

scholarly journals Design and Analysis for a Floating Oscillating Surge Wave Energy Converter

2014 ◽  
Author(s):  
Yi-Hsiang Yu ◽  
Ye Li ◽  
Kathleen Hallett ◽  
Chad Hotimsky
Keyword(s):  
Energy Conversion ◽  
Structure Analysis ◽  
Wave Energy ◽  
Integrated Design ◽  
Design Strategy ◽  
Wave Energy Converter ◽  
Wave Energy Conversion ◽  
Power Performance ◽  
Energy Converter ◽  
The Cost

This paper presents a recent study on the design and analysis of an oscillating surge wave energy converter (OSWEC). A successful wave energy conversion design requires balance between the design performance and cost. The cost of energy is often used as the metric to judge the design of the wave energy conversion (WEC) system, which is often determined based on the device’s power performance; the cost of manufacturing, deployment, operation, and maintenance; and environmental compliance. The objective of this study is to demonstrate the importance of a cost-driven design strategy and how it can affect a WEC design. A set of three oscillating surge wave energy converter designs was analyzed and used as examples. The power generation performance of the design was modeled using a time-domain numerical simulation tool, and the mass properties of the design were determined based on a simple structure analysis. The results of those power performance simulations, the structure analysis, and a simple economic assessment were then used to determine the cost-efficiency of selected OSWEC designs. Finally, we present a discussion on the environmental barrier, integrated design strategy, and the key areas that need further investigation.

scholarly journals An efficient multi-factor geometry optimization based on motion analysis and resonance response for hinged double-body floating wave energy converter

2020 ◽  
Vol 103 (3) ◽  
pp. 003685042095015
Author(s):  
Biao Li ◽  
Fangfang Sui ◽  
Bingsong Yang
Keyword(s):  
Motion Analysis ◽  
Wave Energy ◽  
Geometry Optimization ◽  
Geometric Optimization ◽  
Wave Energy Converter ◽  
Geometrical Parameters ◽  
Optimization Strategy ◽  
Energy Converter ◽  
Pitching Motion ◽  
Resonance Response

In the practical engineering applications of multi-body floating wave energy converter (WEC), the traditional geometric optimization is always expensive and time-consuming. This study aim to propose a more efficient geometry optimization strategy with a hinged double-body floating WEC as the study object. The influences of geometric parameters of the buoys on the pitching motion and energy conversion ability are analyzed by numerical simulation. Simulation results show that the resonance state of the pitching motion of the buoys mainly depends on their radius and draft rather than the length; But the length of the buoys, rather than the radius and draft, always has a significant effect on the pitching phase difference of the adjacent buoys. Based on the motion analysis and resonance response, an efficient multi-factor geometry optimization strategy is put forwarded. By the strategy, the sub-optimal and optimal geometrical parameters are solved out quickly at several typical wave conditions of China Seas. The results indicate that the optimal total length of WEC is approximately equal to the wave length. The optimal diameter of buoys is about 25% of the length of buoys. And the optimal draft should attain about 61% of the diameter.

scholarly journals Effective Mooring Rope Tension in Mechanical and Hydraulic Power Take-Off of Wave Energy Converter

2021 ◽  
Vol 13 (17) ◽  
pp. 9803
Author(s):  
Ji Woo Nam ◽  
Yong Jun Sung ◽  
Seong Wook Cho
Keyword(s):  
Energy Conversion ◽  
Wave Energy ◽  
Mechanical Energy ◽  
Electrical Energy ◽  
Energy Conversion Efficiency ◽  
Wave Energy Converter ◽  
Hydraulic Motor ◽  
Energy Converter ◽  
The Individual ◽  
Conversion Efficiencies

The InWave wave energy converter (WEC), which is three-tether WEC type, absorbs wave energy via moored cylindrical buoys with three ropes connected to a terrestrial power take-off (PTO) through a subsea pulley. In this study, a simulation study was conducted to select a suitable PTO when designing a three-tether WEC. The mechanical PTO transfers energy from the buoy to the generator using a gearbox, whereas the hydraulic PTO uses a hydraulic pump, an accumulator, and a hydraulic motor to convert mechanical energy into electrical energy. The hydraulic PTO has a lower energy conversion efficiency than that of the mechanical PTO owing to losses resulting from pipe friction and the individual efficiencies of the hydraulic pumps and motors. However, the efficiencies mentioned above are not the efficiency of the whole system. The efficiency of the whole system should be analyzed considering the tension of the rope and the efficiency of the generator. In this study, the energy conversion efficiencies of the InWave WEC installed the mechanical and hydraulic PTO devices are compared, and their behaviors are analyzed through numerical simulations. The mechanics of mechanical and hydraulic PTO applied to InWave are mathematically expressed, and the issues of the elements constituting the PTO are explained. Finally, factors to consider for PTO selection are presented.

scholarly journals Numerical simulation of a wave energy converter using linear generator

2013 ◽  
Vol 35 (2) ◽  
pp. 103-111 ◽  
Author(s):  
Dang The Ba
Keyword(s):  
Numerical Simulation ◽  
Wave Energy ◽  
Energy Demand ◽  
Wave Energy Converter ◽  
Linear Potential ◽  
Energy Converter ◽  
Wave Condition ◽  
Mechanics Model ◽  
South Central ◽  
Offshore Wave

This paper presents results of numerical simulation for a wave energy converter using linear permanent magnet generator. The use of linear permanent generator has advantages of simple structure, minimizing mechanical loose... On the base of mechanics model, a system of equations describing the operation of the device under linear potential wave was obtained. The magnetic field in generator was calculated by Flex-PDE software. The system of movement equations was numerically solved with Matlab.Various calculations were performed with different parameters of wave conditions and device's structures to determine the device’s configuration for a 300 W output power for the offshore wave condition in South-Central offshore of Vietnam. The results also show potential of developing the wave energy conversion to meet the energy demand in some coastal and island regions of Vietnam.

scholarly journals Analytical Study on an Oscillating Buoy Wave Energy Converter Integrated into a Fixed Box-Type Breakwater

2017 ◽  
Vol 2017 ◽  
pp. 1-9 ◽  
Author(s):  
Xuanlie Zhao ◽  
Dezhi Ning ◽  
Chongwei Zhang ◽  
Yingyi Liu ◽  
Haigui Kang
Keyword(s):  
Wave Energy ◽  
Wave Energy Converter ◽  
Hydrodynamic Performance ◽  
Maximum Efficiency ◽  
Width Ratio ◽  
Geometrical Parameters ◽  
Linear Potential ◽  
Energy Converter ◽  
Transmission Coefficients ◽  
Incident Waves

An oscillating buoy wave energy converter (WEC) integrated to an existing box-type breakwater is introduced in this study. The buoy is installed on the existing breakwater and designed to be much smaller than the breakwater in scale, aiming to reduce the construction cost of the WEC. The oscillating buoy works as a heave-type WEC in front of the breakwater towards the incident waves. A power take-off (PTO) system is installed on the topside of the breakwater to harvest the kinetic energy (in heave mode) of the floating buoy. The hydrodynamic performance of this system is studied analytically based on linear potential-flow theory. Effects of the geometrical parameters on the reflection and transmission coefficients and the capture width ratio (CWR) of the system are investigated. Results show that the maximum efficiency of the energy extraction can reach 80% or even higher. Compared with the isolated box-type breakwater, the reflection coefficient can be effectively decreased by using this oscillating buoy WEC, with unchanged transmission coefficient. Thus, the possibility of capturing the wave energy with the oscillating buoy WEC integrated into breakwaters is shown.

Sign in / Sign up

Export Citation Format

Share Document