scholarly journals Effects of Discontinuous Thermal Conductivity of a Substrate Surface on Ice Adhesion Strength

2021 ◽  
Vol 9 (11) ◽  
pp. 1209
Author(s):  
Tingkun Chen ◽  
Yiying Chen ◽  
Luquan Ren ◽  
Jingfu Jin ◽  
Qian Cong ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Aluminum Alloy ◽  
Adhesion Strength ◽  
Silicone Rubber ◽  
Substrate Surface ◽  
Freezing Process ◽  
Material Surface ◽  
The Stability ◽  
Surface Ice ◽  
Ice Adhesion

This study proposes a novel anti-icing model in which silicone rubber with low thermal conductivity is coated at different positions on a material surface to change the continuity of the thermal conductivity of the surface. During the test, the surfaces of aluminum alloy and polymethyl methacrylate (PMMA) are discontinuously coated with silicone rubber. Repeated experiments are conducted to verify the anti-icing effect of the proposed model. Results showed that compared to the conventional surface ice adhesion strength, the rate of reduction of the ice adhesion strength of the aluminum alloy and PMMA could reach 75.07% and 76.70%, respectively, when the novel method is used. Because of the different levels of thermal conductivity at different positions on the material surface, the water attached to the surface locations without the coated silicone rubber had other freezing times. Combined with the heat and phase change of water during the freezing process, changing the stability of the interface between the ice and substrate could act as an active anti-icing power. The ice adhesion strength on the material surface could then be reduced. Compared with the conventional anti-icing methods, the anti-icing method proposed in this study could significantly increase the active anti-icing characteristics of the material and provide a novel anti-icing method for use in engineering applications.

scholarly journals Fabrication of Ultralow Ice-Adhesion Slippery Liquid Infused Porous Surfaces on Aluminum Alloy (7075-T651)

Coatings ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1025
Author(s):  
Yuan Yuan ◽  
Liang Wang ◽  
Guoyong Liu ◽  
Ruijin Liao
Keyword(s):  
Aluminum Alloy ◽  
Adhesion Strength ◽  
Water Drop ◽  
Mechanical Damage ◽  
Phosphoric Acid Solution ◽  
Uv Exposure ◽  
Performance Tests ◽  
Porous Surfaces ◽  
Aluminum Alloy 7075 ◽  
Ice Adhesion

Slippery liquid infused porous surfaces (SLIPS) have been considered to be potential and effective method for anti-icing. Much work needed to be done for the application in field. In this study, SLIPS were successfully fabricated on 7075-T651 aluminum alloy by anodizing in phosphoric acid solution with three different voltage parameters and coating lubricant. Then the most suitable anodization parameters of samples were selected through the anti-icing performance tests. The best as-prepared surface exhibited ultralow ice-adhesion strength, which reduced from 261 to 6 kPa. Meanwhile, the freezing time of water-drop on aluminum alloy surfaces have been dramatically delayed at −5 and −10 °C (humidity of 75% ± 5%), respectively. Moreover, the durability of the SLIPS have also been investigated. Cycles of icing/deicing, mechanical damage, thermal and UV exposure were used to investigate the durability of SLIPS, and SLIPS could still show low ice-adhesion strength.

An Experimental Investigation on Thermal Conductivity and Viscosity of Graphene doped CNTs /TiO2 Nanofluid

2020 ◽  
Vol 17 (3) ◽  
Author(s):  
A.M. Zetty Akhtar ◽  
M.M. Rahman ◽  
K. Kadirgama ◽  
M.A. Maleque
Keyword(s):  
Thermal Conductivity ◽  
Zeta Potential ◽  
Base Fluid ◽  
Minimum Quantity Lubrication ◽  
Cutting Fluid ◽  
Cutting Zone ◽  
Observation Method ◽  
The Stability ◽  
The Relationship ◽  
Zeta Potential Analysis

This paper presents the findings of the stability, thermal conductivity and viscosity of CNTs (doped with 10 wt% graphene)- TiO2 hybrid nanofluids under various concentrations. While the usage of cutting fluid in machining operation is necessary for removing the heat generated at the cutting zone, the excessive use of it could lead to environmental and health issue to the operators. Therefore, the minimum quantity lubrication (MQL) to replace the conventional flooding was introduced. The MQL method minimises the usage of cutting fluid as a step to achieve a cleaner environment and sustainable machining. However, the low thermal conductivity of the base fluid in the MQL system caused the insufficient removal of heat generated in the cutting zone. Addition of nanoparticles to the base fluid was then introduced to enhance the performance of cutting fluids. The ethylene glycol used as the base fluid, titanium dioxide (TiO2) and carbon nanotubes (CNTs) nanoparticle mixed to produce nanofluids with concentrations of 0.02 to 0.1 wt.% with an interval of 0.02 wt%. The mixing ratio of TiO2: CNTs was 90:10 and ratio of SDBS (surfactant): CNTs was 10:1. The stability of nanofluid checked using observation method and zeta potential analysis. The thermal conductivity and viscosity of suspension were measured at a temperature range between 30˚C to 70˚C (with increment of 10˚C) to determine the relationship between concentration and temperature on nanofluid’s thermal physical properties. Based on the results obtained, zeta potential value for nanofluid range from -50 to -70 mV indicates a good stability of the suspension. Thermal conductivity of nanofluid increases as an increase of temperature and enhancement ratio is within the range of 1.51 to 4.53 compared to the base fluid. Meanwhile, the viscosity of nanofluid shows decrements with an increase of the temperature remarks significant advantage in pumping power. The developed nanofluid in this study found to be stable with enhanced thermal conductivity and decrease in viscosity, which at once make it possible to be use as nanolubricant in machining operation.

An analysis of the transport properties and mechanical stability of rapidly solidified Al-Sb alloy

2015 ◽  
Vol 10 (2) ◽  
pp. 2663-2681
Author(s):  
Rizk El- Sayed ◽  
Mustafa Kamal ◽  
Abu-Bakr El-Bediwi ◽  
Qutaiba Rasheed Solaiman
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Melt Spinning ◽  
Elastic Moduli ◽  
Mechanical Stability ◽  
Microstructural Analysis ◽  
Alloy System ◽  
Antimony Content ◽  
The Stability ◽  
Rapidly Solidified

The structure of a series of AlSb alloys prepared by melt spinning have been studied in the as melt–spun ribbons  as a function of antimony content .The stability  of these structures has  been  related to that of the transport and mechanical properties of the alloy ribbons. Microstructural analysis was performed and it was found that only Al and AlSb phases formed for different composition.  The electrical, thermal and the stability of the mechanical properties are related indirectly through the influence of the antimony content. The results are interpreted in terms of the phase change occurring to alloy system. Electrical resistivity, thermal conductivity, elastic moduli and the values of microhardness are found to be more sensitive than the internal friction to the phase changes. 

850.0 and 852.0 ALUMINUM ALLOY BEARING BARS

Alloy Digest ◽  
1988 ◽  
Vol 37 (9) ◽  
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Corrosion Resistance ◽  
Aluminum Alloy ◽  
Heat Treating ◽  
Light Metal ◽  
General Purpose ◽  
High Ductility ◽  
Higher Temperature ◽  
Bearing Alloy

Abstract 850.0 ALUMINUM Alloy can be considered the general purpose light metal bearing alloy. Its good thermal conductivity keeps operating temperatures low. It has high ductility. In many applications it has been found to be superior to steel backed bearings. 852.0 ALUMINUM Alloy has higher mechanical properties making it suitable for heavier load and higher temperature applications. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and shear strength. It also includes information on corrosion resistance as well as heat treating and machining. Filing Code: Al-290. Producer or source: Federated Bronze Products Inc..

Evaluation of Ice Adhesion Strength on the Oxidation of Transmission Line ACSR Cable

2019 ◽  
Vol 29 (6) ◽  
pp. 378-384 ◽  
Author(s):  
Hui Jae Cho ◽  
◽  
You Sub Kim ◽  
Yong Chan Jung ◽  
Soo Yeol Lee
Keyword(s):  
Transmission Line ◽  
Adhesion Strength ◽  
Ice Adhesion

scholarly journals Investigation of Hydrothermally Stressed Silicone Rubber/Silica Micro and Nanocomposite for the Coating High Voltage Insulation Applications

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3567
Author(s):  
Faiza Faiza ◽  
Abraiz Khattak ◽  
Safi Ullah Butt ◽  
Kashif Imran ◽  
Abasin Ulasyar ◽  
...  
Keyword(s):  
Silicone Rubber ◽  
Structural Changes ◽  
Polymer Chains ◽  
Hydrothermal Conditions ◽  
Silica Filler ◽  
Before And After ◽  
Aging Conditions ◽  
The Stability ◽  
Micro Silica ◽  
Applied Stresses

Silicone rubber is a promising insulating material that has been performing well for different insulating and dielectric applications. However, in outdoor applications, environmental stresses cause structural and surface degradations that diminish its insulating properties. This effect of degradation can be reduced with the addition of a suitable filler to the polymer chains. For the investigation of structural changes and hydrophobicity four different systems were fabricated, including neat silicone rubber, a micro composite (with 15% micro-silica filler), and nanocomposites (with 2.5% and 5% nanosilica filler) by subjecting them to various hydrothermal conditions. In general, remarkable results were obtained by the addition of fillers. However, nanocomposites showed the best resistance against the applied stresses. In comparison to neat silicone rubber, the stability of the structure and hydrophobic behavior was better for micro-silica, which was further enhanced in the case of nanocomposites. The inclusion of 5% nanosilica showed the best results before and after applying aging conditions.

scholarly journals Study on the Influence of Surface Temperature Field of Aluminum Alloy Etched by Laser Water Jet Composite Machining

Materials ◽  
2020 ◽  
Vol 13 (14) ◽  
pp. 3206
Author(s):  
Xuehui Chen ◽  
Xin Xu ◽  
Wei Liu ◽  
Lei Huang ◽  
Hao Li ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Temperature Field ◽  
Surface Temperature ◽  
Process Parameters ◽  
Water Jet ◽  
Laser Machining ◽  
Material Surface ◽  
Laser Etching ◽  
Surface Temperature Field

This paper studies the compound effect of liquid medium and laser on the workpiece and analyses the law of material surface temperature change during the processing. Taking 7075-T6 aluminum alloy as the research object, the surface temperature field of aluminum alloy processed using water-jet-assisted laser machining under different process parameters was simulated using finite element software. In addition, the temperature field of the material surface was detected in real-time using the self-built water-jet-assisted laser machining temperature field detection system, and the processing results were observed and verified using an optical microscope, scanning electron microscope, and energy spectrum analyzer. The results show that when the water jet inflow angle is 45°, the heat-affected area of the material surface is the smallest, and the cooling effect of the temperature field of the material surface is better. Considering the liquidus melting point of 7075 aluminum alloys, it is concluded that the processing effect is better when the water jet velocity is 14 m·s−1, the laser power is 100 W, and the laser scanning speed is 1.2 mm·s−1. At this time, the quality of the tank is relatively good, there are no cracks in the bottom of the tank, and there is less slag accumulation. Compared with anhydrous laser etching, water-jet-assisted laser etching can reduce the problems of micro-cracks, molten slag, and the formation of a recast layer in laser etching and improve the quality of the workpiece, and the composition of the bottom slag does not change. This study provides theoretical guidance and application support for the selection and optimization of process parameters for water-jet-assisted laser etching of aluminum alloy and further enriches the heat transfer mechanism of multi-field coupling in the process of water-jet-assisted laser machining.

Sign in / Sign up

Export Citation Format

Share Document