An analysis of the transport properties and mechanical stability of rapidly solidified Al-Sb alloy

2015 ◽  
Vol 10 (2) ◽  
pp. 2663-2681
Author(s):  
Rizk El- Sayed ◽  
Mustafa Kamal ◽  
Abu-Bakr El-Bediwi ◽  
Qutaiba Rasheed Solaiman

The structure of a series of AlSb alloys prepared by melt spinning have been studied in the as melt–spun ribbons  as a function of antimony content .The stability  of these structures has  been  related to that of the transport and mechanical properties of the alloy ribbons. Microstructural analysis was performed and it was found that only Al and AlSb phases formed for different composition.  The electrical, thermal and the stability of the mechanical properties are related indirectly through the influence of the antimony content. The results are interpreted in terms of the phase change occurring to alloy system. Electrical resistivity, thermal conductivity, elastic moduli and the values of microhardness are found to be more sensitive than the internal friction to the phase changes. 

2010 ◽  
Vol 667-669 ◽  
pp. 87-90
Author(s):  
Małgorzata Lewandowska ◽  
Henryk Dybiec ◽  
Mariusz Kulczyk ◽  
Jerzy Latuch ◽  
Krzysztof J. Kurzydlowski

The aim of the present work was to compare microstructures and mechanical properties of nano-Al alloys fabricated by two different methods: (i) SPD induced grain refinement, (ii) plastic consolidation of nano-powders or nano-crystalline ribbons. SPD grain refinement has been implemented by hydrostatic extrusion, HE. The ribbons were rapidly solidified using a melt spinning methods. Plastic consolidation of powder and ribbons was conducted by warm extrusion. The results of the studies show that by applying various fabrication routes for a given chemical composition, diverse nano-structures can be obtained, which differ in terms of grain size and shape, grain boundary character and dislocation density. As a result, the alloys also differ significantly in the mechanical properties. The findings are discussed in terms of the possibilities for optimizing properties of the bulk-nano-metals.


Instruments ◽  
2018 ◽  
Vol 2 (4) ◽  
pp. 27
Author(s):  
Levan Glonti ◽  
Temur Enik ◽  
Vladimir Kekelidze ◽  
Alexander Kolesnikov ◽  
Dmitry Madigozhin ◽  
...  

For the development of charged particle detectors based on straw tubes operating in vacuum, a special measurement technique is required for the evaluation of their mechanical properties. A summary of the known equations that govern straw behavior under internal pressure is provided, and a new experimental method of a strained pressurized straw tube study is presented in this paper. The Poisson’s ratio of the straw wall, which defines the stability conditions of a built-in tube, was measured for the NA62 spectrometer straw, and its minimum pre-tension was estimated.


2012 ◽  
Vol 9 (75) ◽  
pp. 2551-2562 ◽  
Author(s):  
Marjorie S. Austero ◽  
Amalie E. Donius ◽  
Ulrike G. K. Wegst ◽  
Caroline L. Schauer

Chitosan (CS), the deacetylated form of chitin, the second most abundant, natural polysaccharide, is attractive for applications in the biomedical field because of its biocompatibility and resorption rates, which are higher than chitin. Crosslinking improves chemical and mechanical stability of CS. Here, we report the successful utilization of a new set of crosslinkers for electrospun CS. Genipin, hexamethylene-1,6-diaminocarboxysulphonate (HDACS) and epichlorohydrin (ECH) have not been previously explored for crosslinking of electrospun CS. In this first part of a two-part publication, we report the morphology, determined by field emission scanning electron microscopy (FESEM), and chemical interactions, determined by Fourier transform infrared microscopy, respectively. FESEM revealed that CS could successfully be electrospun from trifluoroacetic acid with genipin, HDACS and ECH added to the solution. Diameters were 267 ± 199 nm, 644 ± 359 nm and 896 ± 435 nm for CS–genipin, CS–HDACS and CS–ECH, respectively. Short- (15 min) and long-term (72 h) dissolution tests (T 600 ) were performed in acidic, neutral and basic pHs (3, 7 and 12). Post-spinning activation by heat and base to enhance crosslinking of CS–HDACS and CS–ECH decreased the fibre diameters and improved the stability. In the second part of this publication, we report the mechanical properties of the fibres.


2010 ◽  
Vol 658 ◽  
pp. 372-375 ◽  
Author(s):  
Sang Yeop Lee ◽  
Jae Young Kwon ◽  
Tae Woong Kang ◽  
Yeon Gil Jung ◽  
Ung Yu Paik

Thermal barrier coating systems (TBCs) prepared by an air-plasma spray (APS) have been used to protect metallic components of gas turbines because of its economic advantage. To enhance the energy efficiency of gas turbine systems, the operating temperature is increased to over 1300 °C, which requires a new material with low thermal conductivity and an increase of TBC thickness. In this study we have focused the microstructure related to the thickness of TBC and their thermal properties, with specific attention to defect species as well as to its morphology with the thermal exposure time. Resintering of TBC happens during thermal exposure in a high temperature, resulting in the less strain tolerance and the higher thermal conductivity. In order to investigate the thermal properties of TBC related to the microstructural evolution, TBCs with different thicknesses of 200 µm, 400 µm, 600 µm, and 2000 µm were deposited on a flat graphite by the APS. The thermal exposure tests were conducted in different dwell time till 800h at 1100 °C. The thermal diffusivity is significantly increased after thermal exposures, depending on the thermal exposure time. Microstructural analysis clearly shows that the variation of thermal diffusivity is ascribed to the coalescence of small cracks and the resintering effect. The hardness values of TBCs are also increased as well. The relationship between mechanical properties and TBC thickness is discussed, including the effect of thickness on thermal properties.


2018 ◽  
Vol 2018 ◽  
pp. 1-10
Author(s):  
Tomáš Ficker

In the concrete foundations, materials come into contact with bedrocks. The surfaces of bedrocks are often covered by sharp protrusions called asperities. Although geotechnical engineers have developed a reliable theory for assessing the mechanical stability of rocky terrains, the stability of transition zones between concrete and sharp asperities remains unsolved. Due to the large pressures that exist in these transition zones, the invasive influence of sharp asperities on the integrity of the concrete raises a question about possible changes of the mechanical properties of concrete materials used in foundations. These circumstances have inspired experiments in which metallic needles of various lengths have been embedded into cement-based materials to assess the influence of the needles on the compressive strength. This influence has been quantified, and the critical limits identifying the changes of material integrity have been determined. It has been conjectured that sharp rock asperities or needle-like rods of steel reinforcement in concrete may cause similar changes of material integrity as the metallic needles used in the experiments performed.


2020 ◽  
Vol 8 (7_suppl6) ◽  
pp. 2325967120S0044
Author(s):  
Ryan Castile ◽  
Spencer Lake ◽  
Robert Brophy ◽  
Ronak Patel

Objectives: The anterolateral ligament (ALL) of the knee has recently emerged as a potential contributor to rotational stability of the knee, with growing interest in ALL reconstruction as a supplement to anterior cruciate ligament reconstruction. The prevalence of the ALL in the knee has varied in anatomic dissection and imaging studies, raising questions about its importance as a knee stabilizer. The purpose of this study was to assess the microstructural and mechanical properties of the anterolateral knee, to better understand the ALL structure compared to the surrounding anterolateral capsule (ALC) and lateral collateral ligament (LCL). A polarized light imaging technique was used to quantify collagen fiber alignment simultaneously with measurement of tensile mechanical properties. Our primary hypothesis was that there is no difference in the microstructural and mechanical properties between the ALL and ALC. Our secondary hypothesis was that the properties of the LCL are different from the ALL and ALC. Methods: Twenty-five knee specimens from sixteen donors (five males, eleven females; mean age 45.6 +/- 6.4; age range 35-59 years; mean BMI 26.5 +/- 8.4) were obtained as determined by a priori power analysis. The anatomic technique to dissect the anterolateral knee structures was performed as described previously. Three tissue samples (LCL, ALL, and ALC) were harvested (Fig. 1). The ALL was taken as a quadrilateral piece of tissue starting posterior/proximal from the lateral femoral epicondyle and ending at the lateral border of Gerdy’s tubercle. During gross dissection, the knee was assessed for the presence or absence of a distinct visible and palpable structure within the area defined as the ALL. Harvested samples were thinned to approximately 1-mm thick using a freezing-stage sliding microtome. Cross-sectional area was measured using a 3D laser scanning system. Four 0.8-mm diameter aluminum beads were attached to the sample surface to enable strain measurement. Mechanical testing was performed with preconditioning followed by both a stress-relaxation test and a quasi-static ramp to failure. Microstructural analysis was performed using transmitted circularly-polarized incident light and a high-resolution, division-of-focal-plane polarization camera. The average degree of linear polarization (AVG DoLP; i.e., mean strength of collagen alignment) and standard deviation of the angle of polarization (STD AoP; i.e., degree of variation in collagen angle orientation) were calculated for the region of interest of each sample. Statistical analysis was performed using Kruskal-Wallis test (assuming nonparametric data) with Dunn’s correction for multiple comparisons. Results: Mechanical analysis of elastic moduli for the toe- and linear-region of the stress-strain curves showed no difference between the ALL and ALC but were significantly higher for the LCL (p<0.0001; Fig. 2). Microstructural analysis of the ALL and ALC during quasi-static ramp to failure showed no difference in AVG DoLP and STD AoP values at all strain levels (Fig. 3). Larger DoLP values (i.e., stronger collagen fiber alignment) were observed for the LCL than both the ALL and ALC (p<0.0001). Larger STD AoP values (i.e., more variation in collagen orientation) were observed for the ALL and ALC compared to the LCL (p<0.0001; Fig. 3). When looking at correlations between mechanical and microstructural properties (Fig. 4), we found clustering of the LCL data points at high linear modulus and AVG DoLP while the ALL and ALC data points were clustered together. Similarly, we found clustering of the LCL at high linear modulus and low STD AoP while the ALL and ALC were clustered together. Only three of 25 knee specimens (12%) were observed to have a distinct, ligamentous structure in the region of the ALL. Interestingly, these distinct ALL samples (outlined in black on figures) showed relatively larger elastic moduli, higher AVG DoLP, and lower STD AoP (i.e., uniform and organized collagen alignment) across the stress-strain curve compared to samples harvested from knees without a distinct ALL. The distinct ALL tissues were also seen clustered near the LCL data points in the correlation plots. Conclusions: Overall, there were no differences in the mechanical and microstructural properties between the ALL and ALC, while the LCL demonstrated different properties compared to both the ALL and ALC. Both the ALC and ALL show significantly weaker collagen fiber alignment and more variation in the direction of collagen fiber alignment compared to the LCL. These findings suggest that the ALL has similar properties to capsule (i.e., ALC). However, when a distinct ALL was present at dissection (12%), the data indicates stronger and more uniform collagen alignment suggestive of more ligament-type qualities. Further research is needed to more precisely define the prevalence and properties of distinct ALLs in the knee.


2018 ◽  
Vol 3 (5) ◽  
pp. 71
Author(s):  
Joseph Temitope Stephen ◽  
Adeyinka Adebayo ◽  
Gbenga Joshua Adeyemi

This paper reports the influence of solidification rate and stress-relief annealing on the mechanical properties of cast 6063 Aluminium alloy (Al6063). Ingots of Al6063 were melted and then cast using sand and metal moulds. Some of the cast samples were heat treated and then cooled in natural air. Tensile test, hardness test, impact test and microstructural analysis were carried out on the samples. The results show substantial changes in the mechanical properties of the specimens. The ultimate tensile strength, yield strength and hardness percentage elongation of cast Al6063 increases with the use of casting method with high thermal conductivity and reduces when annealing is carried out on the specimens. The ultimate tensile strength of 146.7 MPa and 163.5 MPa were recorded for sand mould and metal mould samples, respectively and the values decreases by 10.3% and 7.5% for the respective moulds. In contrast, the values of impact strength and percentage elongation of cast Al6063 rod improved with the increase in thermal conductivity of casting method and annealing operation. The ductile increased by 51.01% and 45.82% for sand mould and metal mould samples, respectively, after they were annealed. Furthermore, microstructural analysis of cast Al6063 rod revealed a fine-grained structure with increase in thermal conductivity of casting method used; however, the annealing process encouraged grain growth as a result of the stress being relieved from the samples.


1983 ◽  
Vol 28 ◽  
Author(s):  
J.W. Zindel ◽  
J.T. Stanley ◽  
R.D. Field ◽  
H.L. Fraser

ABSTRACTAn investigation was performed to study the origin and stability of microstructures in rapidly solidified aluminum alloys. Al-Ni and Al-Fe base alloys were rapidly solidified by means of laser surface melting and melt spinning techniques. Microstructures were studied using optical and transmission electron microscopy. The effect of microstructure on mechanical properties was also studied using microhardness measurements. The origin of the observed microstructural constituents will be explained in terms of features of the metastable phase diagram. The effect of ternary additions on stability will also be considered.


2021 ◽  
Vol 1035 ◽  
pp. 337-343
Author(s):  
Rong Chen ◽  
Peng Chen ◽  
Xiao Wu Li

The cold-rolled Fe-8Mn-6Al-0.4C duplex low-density steel was annealed at different conditions to obtain ferrite + austenite duplex microstructure. The excellent mechanical properties (i.e., elongation of 52%, tensile strength of 785 MPa, and a product of tensile strength and elongation of 40.9 GPa·%) have been obtained by adjusting the volume fraction and the stability of austenite. The microstructure of the experimental steels was analyzed by scanning electron microscopy (SEM) and electron back-scatter diffraction (EBSD), and the volume fraction of austenite was estimated by the X-ray diffraction (XRD). The results show that the distribution of austenite grain size is inhomogeneous, and that the mechanical stability of austenite is mainly affected by the alloying partitioning and the variation of grain size during the annealing process. The increase of elongation is attributed to the degradation in mechanical stability of austenite, which can efficiently promote an occurrence of transformation induced plasticity (TRIP) effect.


2016 ◽  
Vol 12 (2) ◽  
pp. 4244-4254
Author(s):  
Sara Mosaad Mahlab ◽  
Mustafa Kamal ◽  
Abd El-Raouf Mansour

In the present study, Sn70-X at.% -Bi15 at.% -Sb15 at.%- Inx at.%  alloy ( x= 0, 2, 4, 6),  were prepared by melt spinning technique. Optical microscopy, scanning electron microscopy combined with energy dispersive X-ray analysis (SEM-EDX), X-ray diffraction analysis (XRD), and Vickers microhardness (Hv); were used to characterize the phase transformation and the microstructure evolution. The results contribute to the understanding of the microstructure evolution in alloys of the type prepared by melt spinning technique. This work reports on a comparative study of the rapidly solidified, in order to compare the microhardness and microstructural analysis. 


Sign in / Sign up

Export Citation Format

Share Document