scholarly journals Modification of Collagen Properties with Ferulic Acid

Materials ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3419 ◽  
Author(s):  
Beata Kaczmarek ◽  
Katarzyna Lewandowska ◽  
Alina Sionkowska
Keyword(s):  
Thin Films ◽  
Mechanical Properties ◽  
Ferulic Acid ◽  
Surface Properties ◽  
Apparent Viscosity ◽  
Young Modulus ◽  
Shear Tests ◽  
Elongation At Break ◽  
Collagen Solution ◽  
Significant Difference

Collagen materials are widely used in biomedicine and in cosmetics. However, their properties require improvement for several reasons. In this work, collagen solution as well as collagen films were modified by the addition of ferulic acid (FA). Thin collagen films containing FA were obtained by solvent evaporation. The properties of collagen solution have been studied by steady shear tests. The structure and surface properties of collagen thin films were studied. It was found that for collagen solution with 5% addition of FA, the apparent viscosity was the highest, whereas the collagen solutions with other additions of FA (1%, 2%, and 10%), no significant difference in the apparent viscosity was observed. Thin films prepared from collagen with 1 and 2% FA addition were homogeneous, whereas films with 5% and 10% FA showed irregularity in the surface properties. Mechanical properties, such as maximum tensile strength and elongation at break, were significantly higher for films with 10% FA than for films with smaller amount of FA. Young modulus was similar for films with 1% and 10% FA addition, but bigger than for 2% and 5% of FA in collagen films. The cross-linking of collagen with ferulic acid meant that prepared thin films were elastic with better mechanical properties than collagen films.

scholarly journals Thermal and Mechanical properties of epoxy-jute fiber composite

2014 ◽  
Vol 27 (2) ◽  
pp. 77-82 ◽  
Author(s):  
H Ahmad ◽  
MA Islam ◽  
MF Uddin
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Tensile Strength ◽  
Fiber Length ◽  
Epoxy Composite ◽  
Fiber Composite ◽  
Young Modulus ◽  
Fiber Content ◽  
Jute Fiber ◽  
Elongation At Break

Chopped jute fiber-epoxy composites with varying fiber length (2-12 mm) and mass fraction (0.05-0.35) had been prepared by a heat press unit. The cross-linked product was characterized in terms of specific gravity, thermal conductivity, tensile strength, Young modulus and elongation at break. The transverse thermal conductivities for randomly oriented fibers in the composite were investigated by Lees and Charlton’s method. The tensile strength, Young modulus and elongation at break were investigated by a Universal Tensile Tester. With an increase in the fiber content (irrespective of the fiber length), the thermal conductivity of the composite decreases; the decreasing rate being highest for the fiber length of 2 mm followed by that for the fiber length of 6 and 12 mm. The decreasing rate of the thermal conductivity of the jute-epoxy composite is comparatively higher to that reported in literature for acrylic polymer hemp fiber composite. The tensile strength also decreases with the increase of the fiber content in the composite. The fiber length does not show to have significant effect on the tensile strength of the composite; the variation in strength being masked within experimental error. The Young modulus increases with the increase of fiber content within elastic limit; showing the highest values for the fiber length of 6 mm followed by those for the fiber length of 2 mm and 12 mm. The elongation at break shows slightly increasing trend up to 15% fiber content, but beyond that it decreases drastically. The specific gravity decreases with the increase in the fiber content and thus the recalculated specific tensile strength is found to keep at a stable level of 36MPa up to the fiber content of 20%, and beyond that the specific tensile strength decreases with the increase in the fiber content. It is concluded that jute fiber-epoxy composite could be used as a good heat-insulating material. Further investigation is recommended on the improvement of the thermal insulation keeping the mechanical properties unchanged or even improved. The TGA study is also required to ascertain the field of application of the material. DOI: http://dx.doi.org/10.3329/jce.v27i2.17807 Journal of Chemical Engineering, IEB Vol. ChE. 27, No. 2, December 2012: 77-82

scholarly journals Research Regarding the Mechanical Properties of Some Biodegradable Polymeric Composites for Food Packaging Products

2018 ◽  
Vol 55 (4) ◽  
pp. 498-501
Author(s):  
Constantin Gheorghe Opran ◽  
Elena Grosu ◽  
Marius Enachescu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Injection Molding ◽  
Biodegradable Polymers ◽  
Food Packaging ◽  
Young Modulus ◽  
Important Application ◽  
Elongation At Break ◽  
Amorphous Character ◽  
Sem Analyses

Biodegradable polymers became one of the most important materials with large applicability, as they do not generate wastes after life cycle. An important application is food packaging fabricated by injection molding processing. In this paper, we present the investigation of the mechanical properties of some biodegradable polymers based on PLA composites obtained by melting processing and their morphology studied by SEM analyses, in comparison to polypropylene and neat PLA. We found out that tensile strength, elongation at break and Young modulus exhibit values appropriate to injection molding processing and they are very close related to crystalline or amorphous character of the materials.

scholarly journals Comparative study of sucrose plasticised bioplastic derivatives with selected petro-plastics

2020 ◽  
Vol 12 (1) ◽  
pp. 386-394
Author(s):  
E.C. Agwamba
Keyword(s):  
Mechanical Properties ◽  
High Density Polyethylene ◽  
Production Cost ◽  
Young Modulus ◽  
Raw Material ◽  
Significant Difference ◽  
High Production ◽  
Bulk Matrix ◽  
High Production Cost ◽  
Hcl Concentration

The major setback with most bioplastics is their inherent inability to compete with Petro-plastics in terms of high production cost, and there poor mechanical properties like low tensile strength and percentage extension. This study explore the availability and affordability of mango starch as raw material for bioplastic production and compared some of its mechanical properties with High density Polyethylene (HDPE), Low density polyethylene (LDPE), polyvinyl chloride (PVC), and Polyurethane (PU). Mango starch was used to synthesize bioplastic derivatives, with variable levels of sucrose as plasticiser, aqueous HCl concentration and Carboxymethyl cellulose (CMC) as additive and the mechanical properties of the derived biofilms was measured and compared with the selected Petro-plastics films. It was observed that B1 thermoplastic derivatives have the higher young modulus of 5.658 GPa than that obtained for PVC (4.682 GPa), and PU (3.771 GPa) but show no significant difference and significantly higher than that of HDPE (0.049 GPa), and LDPE (0.063 GPa) (p < 0.05). B2 and B3 indicated a young modulus that is significantly lower than PU and PVC, but showed a young modulus that is higher than LDPE and HDPE with no significant difference (p < 0.05). The FTIR spectra indicate that hydrogen bond was formed in the bulk matrix of the bioplastic derivatives at a band region of 3600 -600 cm-1 wavenumber with broad discrete peaks. Keywords: Petro-plastics; Bioplastics; Mechanical Properties; Plasticization; Mango Starch

Atomic Structure and Mechanical Properties of Defective Carbon Nanotube (7,7)

2016 ◽  
Vol 843 ◽  
pp. 78-84
Author(s):  
Sergey Anatolevich Sozykin ◽  
Valeriy Petrovich Beskachko ◽  
G.P. Vyatkin
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotube ◽  
Atomic Structure ◽  
Young Modulus ◽  
Vacancy Defect ◽  
First Principle ◽  
Single Vacancy ◽  
Elongation At Break ◽  
Vacancy Defects ◽  
Defect Type

The article presents the results of first-principle modeling of a defectless (7,7) carbon nanotube and (7,7) nanotubes containing single and double vacancy defects, as well as Stone–Wales defects. These types of defects are often found in real nanotubes and affect their properties. We have established that reliable results can be obtained by using models of more than 1.5 nm in length. It turned out that a single vacancy defect has the least influence on Young modulus, and double n type vacancy defect in the most influential. The elongation at break also depends on the defect type and is 30-60% less than for perfect tubes.

scholarly journals Development of Electrically Conductive Nanocrystalline Thin Film for Optoelectronic Applications

2013 ◽  
Vol 15 ◽  
pp. 90-101 ◽  
Author(s):  
Sujan Kumar Das ◽  
Jahid M.M. Islam ◽  
Monirul Hasan ◽  
Humayun Kabir ◽  
Md Abdul Gafur ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electrical Properties ◽  
Composite Films ◽  
Young Modulus ◽  
Electrically Conductive ◽  
Elongation At Break ◽  
Ohmic Behavior ◽  
Nanocrystalline Thin Film ◽  
Electrically Conductive Composite

Sodium alginate (TiO2) sand composites were prepared by solution casting. Purified sand was added in the composite films to increase electrical conductivity. Electrical properties such as conductivity, capacitance, dielectric constant, and loss tangent of the composites were investigated. The current voltage characteristics for all the composites showed ohmic behavior. All the electrical properties have been found to improve with the incorporation of sand (SiO2) but 6% sand containing composite exhibits the best electrical properties. The mechanical properties tensile strength (TS), elongation at break (Eb) and Young modulus for 6% sand containing composite film are found to be 4.445 MPa, 9.76%, and 72.8 MPa respectively. The experimental results reveal that the blended films exhibit higher stability and improved mechanical properties of both tensile strength and elongation at break in dry state. Water absorption properties of the composites are found to decrease with the increase of sand content. Lowest water uptake properties and highest stability were demonstrated by 6% sand containing sample. Electrically conductive composite films have useful applications for solar cells and optoelectronics. Thus, this study is very much expected to aid in the design and selection of proper composite for the potential application of solar cell and optoelectronics.

Synthesis, Characterization and Antibacterial Activity of ε-Polylysine/PVA Biodegradable Film

2013 ◽  
Vol 834-836 ◽  
pp. 96-99 ◽  
Author(s):  
Zhi Lei Tan ◽  
Miao Miao Xia ◽  
Shi Ru Jia ◽  
Fang Lian Yao
Keyword(s):  
Mechanical Properties ◽  
Antibacterial Activity ◽  
Young Modulus ◽  
Biodegradable Films ◽  
Biodegradable Film ◽  
Neat Polymer ◽  
Elongation At Break ◽  
Good Antibacterial Activity ◽  
Potential Applications ◽  
Packaging Industry

ε-polylysine (ε-PL) was blended with polyvinyl alcohol (PVA) to obtain biodegradable films. Blends and neat polymer films (PVA) were characterized for their structural and mechanical properties as well as antibacterial activity. The addition of ε-polylysine reduced Young modulus (Eyoung), tensile strength (TS) and elongation at break (%E) of the ε-polylysine/PVA film. The ε-polylysine/PVA film shows good antibacterial activity and therefore has potential applications in packaging industry.

scholarly journals Hybrid Nanocarbons Reinforced Rubber Nanocomposites: Detailed insights about Mechanical, Dynamical Mechanical Properties, Payne and Mullin Effects

2018 ◽  
Author(s):  
Suneel Kumar Srivastava ◽  
Yogendra Kumar Mishra
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Young Modulus ◽  
Expanded Graphite ◽  
Dynamic Mechanical Properties ◽  
Multiwalled Carbon ◽  
Elongation At Break ◽  
Hybrid Fillers ◽  
Rubber Nanocomposites ◽  
Walled Carbon Nanotubes

The reinforcing ability of the fillers results in significant improvements in properties of polymer matrix at extremely low filler loadings compared to conventional fillers. In view of this, present review article describes the different methods used in preparation of different rubber nanocomposites reinforced with nanodimensional individual carbonaceous fillers, such as graphene, expanded graphite, single walled carbon nanotubes, multiwalled carbon nanotubes and graphite oxide, graphene oxide and hybrid fillers consisting combination of individual fillers. This is followed by review of mechanical properties (tensile strength, elongation at break, Young modulus, and fracture toughness) and dynamic mechanical properties (glass transition temperature, crystallization temperature, melting point) of these rubber nanocomposites. Finally, Payne and Mullin Effects have also been reviewed in rubber filled with different carbon based nanofillers.

scholarly journals Nanocarbon Reinforced Rubber Nanocomposites: Detailed Insights about Mechanical, Dynamical Mechanical Properties, Payne, and Mullin Effects

Nanomaterials ◽  
2018 ◽  
Vol 8 (11) ◽  
pp. 945 ◽  
Author(s):  
Suneel Srivastava ◽  
Yogendra Mishra
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Young Modulus ◽  
Expanded Graphite ◽  
Dynamic Mechanical Properties ◽  
Multiwalled Carbon ◽  
Elongation At Break ◽  
Hybrid Fillers ◽  
Rubber Nanocomposites ◽  
Walled Carbon Nanotubes

The reinforcing ability of the fillers results in significant improvements in properties of polymer matrix at extremely low filler loadings as compared to conventional fillers. In view of this, the present review article describes the different methods used in preparation of different rubber nanocomposites reinforced with nanodimensional individual carbonaceous fillers, such as graphene, expanded graphite, single walled carbon nanotubes, multiwalled carbon nanotubes and graphite oxide, graphene oxide, and hybrid fillers consisting combination of individual fillers. This is followed by review of mechanical properties (tensile strength, elongation at break, Young modulus, and fracture toughness) and dynamic mechanical properties (glass transition temperature, crystallization temperature, melting point) of these rubber nanocomposites. Finally, Payne and Mullin effects have also been reviewed in rubber filled with different carbon based nanofillers.

About the Mechanical Properties for Composites Reinforced with Felt

2021 ◽  
Vol 42 ◽  
pp. 30-35
Author(s):  
Alexandru Ioan Rădoi ◽  
Cosmin Mihai Miriţoiu ◽  
Alexandru Bolcu ◽  
Valeriu Ionică ◽  
Alina Elena Romanescu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Testing Machine ◽  
Young Modulus ◽  
Optical Microscope ◽  
Elongation At Break ◽  
The Matrix ◽  
Static Mechanical ◽  
Static Mechanical Properties ◽  
Made In

In this paper we present some researches about the static mechanical properties for some composites made in this way: the reinforcement is made from two types of felt and the matrix is from epoxy resin Resoltech 1050 with its hardener Resoltech 1055. There are built some plates from felt/epoxy resin and from these plates there are cut some samples. The samples are tensile loaded on an universal testing machine Instron 1000 HDX which is assisted by a BlueHill software. There are determined the next mechanical properties: Young modulus, yield strength, elongation at break and breaking strength. By using an optical microscope, there are presented some images with the breaking sections.

scholarly journals Preparation of Biodegradable Materials by Reactive Extrusion

2008 ◽  
Vol 587-588 ◽  
pp. 520-524 ◽  
Author(s):  
Isabel Moura ◽  
Ana Vera Machado ◽  
Fernando M. Duarte ◽  
Gabriela Botelho ◽  
Regina Nogueira
Keyword(s):  
Mechanical Properties ◽  
High Density Polyethylene ◽  
Young Modulus ◽  
Polymeric Materials ◽  
Reactive Extrusion ◽  
Biodegradable Materials ◽  
Screw Extruder ◽  
Elongation At Break ◽  
Twin Screw ◽  
Poly Caprolactone

This work aimed to prepare biodegradable polymeric materials based on blends of a synthetic high density polyethylene (HDPE) and biodegradable polymers such as polylactic acid (PCL) and poly(caprolactone) (PLA), in a co-rotating twin-screw extruder. A polyethylene modified with maleic anhydride was used as compatibiliser. The mechanical results showed that the addition of PLA improves the blends stiffness while the addition of PCL leads to materials with a greater elongation at break and a lower Young modulus. This feature is related with the mechanical properties of each material as well as the adhesion between them. Concerning the biodegradability tests, it was found that HDPE/PCL blend presents the highest degree of biodegradability.

Sign in / Sign up

Export Citation Format

Share Document