scholarly journals Novel Biocompatible Zr-Based Alloy with Low Young’s Modulus and Magnetic Susceptibility for Biomedical Implants

Materials ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5130
Author(s):  
Renhao Xue ◽  
Dong Wang ◽  
Dawei Yang ◽  
Ligang Zhang ◽  
Xiaoning Xu ◽  
...  
Keyword(s):  
Magnetic Susceptibility ◽  
Young’S Modulus ◽  
Blood Compatibility ◽  
Young's Modulus ◽  
Emission Spectrometry ◽  
Biomedical Implants ◽  
Ion Release ◽  
Mg63 Cells ◽  
Ti Addition

The microstructure, mechanical properties, magnetic susceptibility, electrochemical corrosion performance, in vitro cell compatibility and blood consistency of Zr-16Nb-xTi (x = 0, 4, 8, 12 and 16 wt.%) materials were investigated as potential materials for biomedical implants. X-ray diffraction (XRD) and Transmission electron microscopy (TEM) analyses revealed the secondary phase martensite α’ formed during the quenching process. The phase composition contained metastable β and martensite α’, resulting from Ti addition. These phase constitutions were the main causes of a low Young’s modulus and magnetic susceptibility. The in vitro cytocompatibility analysis illustrated that the MG63 cells maintained high activity (from 91% to 97%) after culturing in Zr-16Nb-xTi extraction media for 12 days due to the high internal biocompatibility of Zr, Nb and Ti elements, as well as the optimal corrosion resistance of Zr-16Nb-xTi. On the basis of Inductively coupled plasma optical emission spectrometry (ICP-OES) ion release studies, the concentration of Zr, Nb and Ti was noted to reach the equipment detective limit of 0.001 mg/L, which was much lower than pure Ti. With respect to the corrosion behavior in Hank’s solution, Zr-16Nb-16Ti displayed superior properties, possessing the lowest corrosion current density and widest passivation region, attributed to the addition of Ti. The blood compatibility test illustrated that the Zr-16Nb-xTi materials were nonhemolytic, and the platelets maintained a spherical shape, with no aggregation or activation on Zr-16Nb-xTi. Overall, Ti addition has obvious effects on the developed Zr-16Nb-xTi alloys, and Zr-16Nb-4Ti exhibited low magnetic susceptibility, low modulus, good biocompatibility and proper corrosion properties, demonstrating the potential of use as implant biomaterials.

scholarly journals Effect of dissolution rate and subsequent ion release on cytocompatibility properties of borophosphate glasses

2019 ◽  
Vol 5 (1) ◽  
pp. 85-97
Author(s):  
Nusrat Sharmin ◽  
Mohammad S. Hasan ◽  
Md. Towhidul Islam ◽  
Chengheng Pang ◽  
Fu Gu ◽  
...  
Keyword(s):  
Dissolution Rate ◽  
Laser Scanning ◽  
Laser Scanning Microscopy ◽  
Confocal Laser ◽  
Ion Release ◽  
Scanning Calorimetry ◽  
Cell Culture Study ◽  
Borophosphate Glasses ◽  
Mg63 Cells

AbstractPresent work explores the relationship between the composition, dissolution rate, ion release and cytocompatibility of a series of borophosphate glasses. While, the base glass was selected to be 40mol%P2O5-16mol%CaO-24mol%MgO-20mol%Na2O, three B2O3 modified glass compositions were formulated by replacing Na2O with 1, 5 and 10 mol% B2O3. Ion release study was conducted using inductively coupled plasma atomic emission spectroscopy (ICP-AES). The thermal scans of the glasses as determined by differential scanning calorimetry (DSC) revealed an increment in the thermal properties with increasing B2O3 content in the glasses. On the other hand, the dissolution rate of the glasses decreased with increasing B2O3 content. To identify the effect of boron ion release on the cytocompatibility properties of the glasses, MG63 cells were cultured on the surface of the glass discs. The in vitro cell culture study suggested that glasses with 5 mol% B2O3 (P40B5) showed better cell proliferation and metabolic activity as compares to the glasses with 10 mol% (P40B10) or with no B2O3 (P40B0). The confocal laser scanning microscopy (CLSM) images of live/dead stained MG63 cells attached to the surface of the glasses also revealed that the number of dead cells attached to P40B5 glasses were significantly lower than both P40B0 and P40B10 glasses.

scholarly journals AFM-based Analysis of Wharton’s Jelly Mesenchymal Stem Cells

2019 ◽  
Vol 20 (18) ◽  
pp. 4351
Author(s):  
Renata Szydlak ◽  
Marcin Majka ◽  
Małgorzata Lekka ◽  
Marta Kot ◽  
Piotr Laidler
Keyword(s):  
Stem Cells ◽  
Mesenchymal Stem Cells ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Wharton’S Jelly ◽  
In Vitro Cultivation ◽  
Multipotent Stem Cells ◽  
Wharton's Jelly ◽  
Migration Potential

Wharton’s jelly mesenchymal stem cells (WJ-MSCs) are multipotent stem cells that can be used in regenerative medicine. However, to reach the high therapeutic efficacy of WJ-MSCs, it is necessary to obtain a large amount of MSCs, which requires their extensive in vitro culturing. Numerous studies have shown that in vitro expansion of MSCs can lead to changes in cell behavior; cells lose their ability to proliferate, differentiate and migrate. One of the important measures of cells’ migration potential is their elasticity, determined by atomic force microscopy (AFM) and quantified by Young’s modulus. This work describes the elasticity of WJ-MSCs during in vitro cultivation. To identify the properties that enable transmigration, the deformability of WJ-MSCs that were able to migrate across the endothelial monolayer or Matrigel was analyzed by AFM. We showed that WJ-MSCs displayed differences in deformability during in vitro cultivation. This phenomenon seems to be strongly correlated with the organization of F-actin and reflects the changes characteristic for stem cell maturation. Furthermore, the results confirm the relationship between the deformability of WJ-MSCs and their migration potential and suggest the use of Young’s modulus as one of the measures of competency of MSCs with respect to their possible use in therapy.

Mechanical Properties and Microarchitecture of Nanoporous Hydroxyapatite Bioceramic Nanoparticle Coatings on Ti and TiN

2006 ◽  
Vol 975 ◽  
Author(s):  
Andrei Stanishevsky ◽  
Shafiul Chowdhury ◽  
Nathaniel Greenstein ◽  
Helene Yockell-Lelievre ◽  
Jari Koskinen
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Biological Response ◽  
Dip Coating ◽  
Nano Crystalline ◽  
Ceramic Manufacturing ◽  
Nanoparticle Coatings

ABSTRACTThe hydroxyapatite (HA) based bioceramic materials are usually prepared at high sintering temperatures to attain suitable mechanical properties. The sintering process usually results in a material which is compositionally and morphologically different from nonstoichiometric nano-crystalline HA phase of hard tissue. At the same time, HA particulates used as precursors in ceramic manufacturing are often very similar to the natural HA nanocrystals. It has been shown that synthetic nanoparticle HA (nanoHA) based materials improve the biological response in vitro and in vivo, but the information on mechanical properties of these materials is scarce.In this work we studied the HA nanoparticle (10 – 80 nm mean size) coatings with 30 – 70% porosity prepared by a dip-coating technique on Ti and TiN substrates. It has been found that the mechanical properties of HA nanoparticle coatings are strongly influenced by the initial size, morphology, and surface treatment of nanoparticles. The nanoindentation Young's modulus and hardness of as–deposited nanoHA coatings were in the range of 2.5 – 6.9 GPa and 80 – 230 MPa, respectively. The coatings were stable after annealing up to at least 600 °C, reaching the Young's modulus up to 23 GPa and hardness up to 540 MPa, as well as in simulated body fluids.

scholarly journals Comparative investigations of in vitro and in vivo bioactivity of titanium vs. Ti–24Nb–4Zr–8Sn alloy before and after sandblasting and acid etching

RSC Advances ◽  
2020 ◽  
Vol 10 (40) ◽  
pp. 23582-23591
Author(s):  
Xin Liu ◽  
Yumei Niu ◽  
Weili Xie ◽  
Daqing Wei ◽  
Qing Du
Keyword(s):  
Young’S Modulus ◽  
Young's Modulus ◽  
Stress Shielding ◽  
Acid Etching ◽  
Implant Material ◽  
Before And After ◽  
New Type

To avoid the failure of clinical surgery due to “stress shielding” and the loosening of an implant, a new type of alloy, Ti–24Nb–4Zr–8Sn (TNZS), with a low Young's modulus acted as a new implant material in this work.

Role of pH on stability and mechanical properties of gelatin films

2012 ◽  
Vol 27 (1) ◽  
pp. 67-77 ◽  
Author(s):  
Michela Gioffrè ◽  
Paola Torricelli ◽  
Silvia Panzavolta ◽  
Katia Rubini ◽  
Adriana Bigi
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Triple Helix ◽  
Young's Modulus ◽  
In Vitro Tests ◽  
Diffraction Reflection ◽  
X Ray Diffraction ◽  
Solution Ph ◽  
Gelatin Films

The effect of the film-forming solution pH on the triple-helix content, thermal stability, and mechanical properties of gelatin films was investigated. The films were prepared from solutions at different pHs of type A pigskin gelatin, and their mechanical characteristics were determined. At pHs higher than 9 and lower than 5, Young’s modulus, E, and the stress at break, σb, of the films decreased significantly. Cross-linking with genipin reduced deformation at break, ϵb, and increased Young’s modulus. The intensity of the 1.1-nm X-ray diffraction reflection and the denaturation enthalpy decreased at these pHs, indicating that the triple helix reduced. Preliminary in vitro tests on the cross-linked samples indicated good cell proliferation and viability.

Effects of endodontic treatment on apparent Young’s modulus of human teeth: in vitro study using speckle interferometry

2012 ◽  
Vol 17 (4) ◽  
pp. 048002 ◽  
Author(s):  
Rolando J. González-Peña ◽  
Rosario Salvador ◽  
Rosa M. Cibrián ◽  
René A. Martinez-Celorio ◽  
Francisco J. López ◽  
...  
Keyword(s):  
Young’S Modulus ◽  
Young's Modulus ◽  
In Vitro Study ◽  
Speckle Interferometry ◽  
Endodontic Treatment ◽  
Vitro Study ◽  
Human Teeth

scholarly journals Development and characterization of k-carrageenan platforms as periodontal intra-pocket films

2021 ◽  
Vol 18 (9) ◽  
pp. 1791-1798
Author(s):  
Ola Tarawneh ◽  
Ameen Rasheed Al-Ass ◽  
Rania Hamed ◽  
Suhair Sunoqrot ◽  
Lina Hasan ◽  
...  
Keyword(s):  
Drug Release ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Viable Count ◽  
Efficient Treatment ◽  
Thermal Analyser ◽  
Noticeable Reduction ◽  
Microbial Adherence

Purpose: To prepare emulsion-based Intrapocket polymeric films for the treatment of periodontitis. Method: Films were fabricated by dehydration of an emulsion containing k-carrageenan (KC) in aqueous phase and Compritol® 888 ATO (Compritol® ) or Dimodan® UJ (DU® ) or different ratios of both. The resulting films were characterized by mechanical texture analyser to determine Young’s modulus and tensile strength. Glass transition temperature (Tg) of the films was evaluated by dynamic mechanical and thermal analyser while surface morphology was evaluated using scanning electron microscope. In-vitro drug release was conducted in pre-warmed phosphate buffer. Bacterial adherence was assessed after 24 h. Results: Young’s modulus was highest for KC films to which no lipid was added (5.33 ± 0.38 GPa) and decreased following lipid incorporation. Tg was highest in KC films (106.25 ± 4.53 ° C) but decreased upon addition of lipids. The surface of KC was smooth but roughness increased with increasing Compritol® load. Drug release from KC films was complete (99.80 ± 8.43 %) after 2 h; however, upon adding lipid, the release was extended 8 h and was affected by lipid type and ratio. Microbiologic assay demonstrated noticeable reduction in viable count compared to control and was affected by lipid type and ratio. The film formulated from a combination of DU® and Compritol® in a ratio of 80:20 was strong, flexible and reduced microbial adherence. Moreover, it showed a smooth surface and extended release for over 8 h. Conclusion: Intra-pocket films were prepared by drying emulsion-based films. Resulted films were strong, flexible, prolonged drug release over 8 h and could lower bacterial growth. The prepared film may offer efficient treatment in periodontitis patients.

Biodegradation of Poly(3-Hydroxybutyrate) and Poly(3-Hydroxybutyrate-Co-3-Hydroxy-4-Methylvalerate) Films by Porcine Pancreatic Lipase

2018 ◽  
Vol 779 ◽  
pp. 57-63
Author(s):  
Vsevolod Zhuikov ◽  
Alexey Rusakov ◽  
Alexey Useinov ◽  
Elizaveta Akulina ◽  
Vera Voinova
Keyword(s):  
Molecular Weight ◽  
Weight Loss ◽  
Young’S Modulus ◽  
Pancreatic Lipase ◽  
Degradation Rate ◽  
Great Increase ◽  
Young's Modulus ◽  
Porcine Pancreatic Lipase ◽  
Film Properties

In the current work, the degradation of poly (3-hydroxybutyrate) (PHB) and poly (3-hydroxybutyrate-co-3-hydroxy-4-methylvalerate) (PHB4MV) films was studied in vitro by pancreatic lipase. The changes in film properties were traced by several analytical methods: the change of weight, molecular weight, and Young’s modulus (by nanoindentation) were measured. During the six months of polymer films degradation the weight of samples decreased slightly, while a great increase in Young's modulus due to the relatively fast degradation of the amorphous areas was observed, as well as molecular weight of polymers decreased significantly. Weight loss of PHB4MV is faster than degradation rate of PHB, but the molecular weight of PHB 1700 decrease rapidly than PHB4MV; the Young’s modulus of polymers remained relatively unchanged.

Sign in / Sign up

Export Citation Format

Share Document