scholarly journals Alloying Elements Effects on Electrical Conductivity and Mechanical Properties of Newly Fabricated Al Based Alloys Produced by Conventional Casting Process

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3971
Author(s):  
Hany S. Abdo ◽  
Asiful H. Seikh ◽  
Jabair Ali Mohammed ◽  
Mahmoud S. Soliman
Keyword(s):  
Mechanical Properties ◽  
Electrical Conductivity ◽  
Pure Aluminum ◽  
Casting Process ◽  
Graphite Crucible ◽  
Alloying Elements ◽  
Mg Alloy ◽  
Age Hardening ◽  
Heat Treated ◽  
Alloying Additives

The present investigation deals with a comprehensive study on the production of aluminum based alloys with the incorporation of different alloying elements and their effect on its electrical conductivity and mechanical properties. Casting of pure aluminum with different concentration and combinations of alloying additives such as cupper (Cu), magnesium (Mg) and silver (Ag) were carried out using a graphite crucible. The as-cast microstructure was modified by hot rolling followed by different heat-treated conditions viz., annealing, normalizing, quenching, and age hardening. The mechanical properties and electrical conductivity of the produced heat-treated alloys sheets under various processing conditions were carried out using tensile testing, hardness, and electrical resistivity measurements. It was found that by increasing the alloying elements content, yield strength results increased significantly by more than 250% and 500% for the as rolled and 8 h aged Al-Cu-Mg alloy, respectively. On the other hand, the electrical conductivity reduces slightly with −14.6% and −16.57% for the as rolled and 8 h aged of the same Al-Cu-Mg alloy, respectively.

Comparison of Microstructure and Mechanical Properties of Semi-Solid Castings Produced Using Billets Made by EMS and SEED

2014 ◽  
Vol 217-218 ◽  
pp. 332-339 ◽  
Author(s):  
Xiao Kang Liang ◽  
Da Quan Li ◽  
Pascal Côté ◽  
Stephen P. Midson ◽  
Qiang Zhu
Keyword(s):  
Mechanical Properties ◽  
Cross Section ◽  
Dendritic Structure ◽  
Casting Process ◽  
Grain Structure ◽  
High Quality ◽  
Microstructure And Mechanical Properties ◽  
Grain Structures ◽  
Heat Treated ◽  
Semi Solid

The spheroidal grains in billets used for semi-solid casting are generally manufactured by electromagnetic stirring (EMS) during the casting process. This method however, is not economically applicable for small quantities of the thixo billets. Swirled Enthalpy Equilibration Device (SEED) has been developed as a rheocasting process, and the SEED process is of interest for developing new thixo alloys, as well as for optimizing the thixocasting processes for high quality components. The objective of this paper is to compare the microstructure and mechanical properties of aluminum alloy 319s billets and castings produced using EMS and SEED feed materials. The experimental results show that for as-cast billets made from SEED process, a well-developed spheroidal grain structure is distributed throughout the cross-section of the billet, while for as-cast EMS billets, the grain structure is inhomogeneous, i.e., a dendritic structure was present adjacent to the surface of the billet, while a uniform, spheroidal structure was present at the centre. After the thixocasting process, however, the both SEED and EMS billets have well-developed, spheroidal grain structures. Mechanical properties of thixocast and T61 heat treated components are comparable for the both SEED and EMS billets.

scholarly journals Asymmetric Twin-Roll Casting of an Al-Mg-Si-Alloy

2018 ◽  
Vol 918 ◽  
pp. 48-53 ◽  
Author(s):  
Olexandr Grydin ◽  
Mykhailo Stolbchenko ◽  
Maria Bauer ◽  
Mirko Schaper
Keyword(s):  
Mechanical Properties ◽  
Casting Process ◽  
Rolling Process ◽  
Age Hardening ◽  
Process Conditions ◽  
Shear Stresses ◽  
Asymmetric Rolling ◽  
Twin Roll Casting ◽  
Roll Casting ◽  
Twin Roll

The industrial application of high-alloyed Al-Mg-Si alloys for the production of thin strips by means of twin-roll casting is limited due to the structural inhomogeneity and segregation formation. To reach the highest mechanical properties of the finished product, a direct influence on the strip formation conditions during the twin-roll casting can be applied. Analogous to the asymmetric rolling process, additional shear stresses were created in the strip forming zone by using different circumferential velocities and torques of the caster rolls. To provide the asymmetric process conditions, only one caster roll was left driven and the second one was left idling during the casting process. The microstructure and the mechanical properties of the strips in the as-cast state as well as after the homogenization and subsequent age-hardening were analyzed. A comparison of the test results showed a positive influence of the asymmetry conditions on the strips’ properties.

Effects of Post Weld Heat Treatments (PWHT) on Friction Stir Welded AA2219-T87 Joints

2017 ◽  
Author(s):  
Mohammad W. Dewan ◽  
Muhammad A. Wahab ◽  
Khurshida Sharmin
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloys ◽  
Yield Strength ◽  
Solution Treatment ◽  
Welding Process ◽  
Alloying Elements ◽  
Age Hardening ◽  
Experimental Program ◽  
Friction Stir ◽  
Aging Period

Friction Stir Welding (FSW) offers significantly better performance on aluminum alloy joints compared to the conventional fusion arc welding techniques; however, plastic deformation, visco-plastic flow of metals, and complex non-uniform heating cycles during FSW processes, result in dissolution of alloying elements, intrinsic microstructural changes, and post-weld residual stress development. As a consequence, about 30% reduction in ultimate strength (UTS) and 60% reduction in yield strength (YS) were observed in defect-free, as-welded AA2219-T87 joints. PWHT is a common practice to refine grain-coarsened microstructures which removes or redistributes post-weld residual stresses; and improves mechanical properties of heat-treatable welded aluminum alloys by precipitation hardening. An extensive experimental program was undertaken on PWHT of FS-welded AA2219-T87 to obtain optimum PWHT conditions and improvement of the tensile properties. Artificial age-hardening (AH) helped in the precipitation of supersaturated alloying elements produced around weld nugget area during the welding process. As a result, an average 20% improvement in YS and 5% improvements in UTS was observed in age-hardened (AH-170°C-18h) specimens as compared to AW specimens. To achieve full benefit of PWHT, solution-treatment followed by age-hardening (STAH) was performed on FS-welded AA2219-T87 specimens. Solution-treatment (ST) helps in the grain refinement and formation of supersaturated precipitates in aluminum alloys. Age-hardening of ST specimens help in the precipitation of alloying elements around grain boundaries and strengthen the specimens. Optimum aging period is important to achieve better mechanical properties. For FS-welded AA2219-T87 peak aging time was 5 hours at 170°C. STAH-170°C -5h treated specimens showed about 78% JE based on UTS, 61% JE based on yield strength, and 36% JE based on tensile toughness values of base metal.

scholarly journals Microstructure as an essential aspect of EN AW 7075 aluminum alloy quality influenced by electromagnetic field during continuous casting process

2021 ◽  
Vol 75 (1) ◽  
pp. 31-37
Author(s):  
Aleksandra Pataric ◽  
Marija Mihailovic ◽  
Branislav Markovic ◽  
Miroslav Sokic ◽  
Andreja Radovanovic ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Electrical Conductivity ◽  
Electromagnetic Field ◽  
Aluminum Alloy ◽  
Continuous Casting ◽  
Cast Alloy ◽  
Casting Process ◽  
Cast Aluminum Alloy ◽  
Cast Aluminum ◽  
Continuous Casting Process

Microstructure assessment is crucial for the design and production of high-quality alloys such as cast aluminum alloy ingots. Along with the effect of a more homogeneous microstructure to result in much better mechanical properties, better as-cast alloy quality indicates a higher efficiency of the aluminum alloys production process. During the aluminum alloy solidification process many microstructural defects can occur, which deteriorate the mechanical properties and hence decrease the usability of such an ingot. Application of the electromagnetic field during the vertical continuous casting process significantly reduces occurrence of these defects. In the present study, EN AW 7075 alloy samples were cast with and without application of an electromagnetic field and examined regarding the microstructure, electrical conductivity, and changes in the phase composition. The obtained results clearly show that it is possible to decrease or avoid casting defects by the electromagnetic field application as verified by the microstructure characterization and quantification, electrical conductivity tests and differential thermal analysis (DTA).

scholarly journals Creep properties of 1.25Cr-1Mo-0.25V steels for turbine casings

2005 ◽  
Vol 58 (2) ◽  
pp. 165-173
Author(s):  
Sergio G. Hernández ◽  
Alberto N. Conejo
Keyword(s):  
Mechanical Properties ◽  
Rupture Strength ◽  
Casting Process ◽  
Resistant Steel ◽  
Heat Resistant Steel ◽  
Creep Properties ◽  
Rapid Estimation ◽  
Heat Treated ◽  
Short Time ◽  
Quenching And Tempering

A heat resistant steel, 1.25Cr-1Mo-0.25V, produced by a casting process and used in the manufacture of turbine casings, has been heat treated with a combination of thermal cycles that involve annealing, quenching and tempering in order to obtain high mechanical properties - in particular, rupture-strength at high temperatures. The Larson-Miller Parameter has been used to predict results from short-time tests (50 hours) with those obtained at longer times (3000-20000 hours). The predictions resulted in higher rupture-times. However, the current methodology can provide a rapid estimation of creep-behavior at longer times from short-time tests in order to take corrective actions during the manufacturing process.

Microstructural and Vickers Microhardness Evolution of Heat Treated Secondary Aluminium Cast Alloy

2013 ◽  
Vol 586 ◽  
pp. 137-140 ◽  
Author(s):  
Lenka Hurtalová ◽  
Eva Tillová ◽  
Mária Chalupová
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Artificial Aging ◽  
Vickers Microhardness ◽  
Cast Alloy ◽  
Solution Treatment ◽  
Holding Time ◽  
Age Hardening ◽  
Structural Components ◽  
Heat Treated

Secondary aluminium alloys are made out of aluminium scrap and aluminium-processable waste by recycling. These alloys contain different alloying elements such as Al, Cu, Fe, Si and Mg that form intermetallic phases in aluminium matrix and influence on the microstructure, basic mechanical properties and microhardness evolution in aluminium cast alloy. As experimental material was used secondary aluminium cast alloy AlSi9Cu3. Material was subjected to heat treatment (age-hardening) consisting of a solution treatment at temperature 515 °C with holding time 4 hours, than water quenching at 40 °C and artificial aging by different temperature 130 °C, 150 °C and 170 °C with different holding time (2, 4, 8, 16 and 32 hours). The age-hardening led to changes in the morphology of structural components, but also leads to precipitation of finer hardening phases in the material substructure. As optimal age-hardening mode for secondary aluminium cast alloy AlSi9Cu3 was determined mode consisting of solution treatment at temperature 515 °C with holding time 4 hours and artificial aging at temperature 170 °C with holding time 16 hours. After this heat treatment cast alloy shows the best changes in microstructure and mechanical properties. These changes are comparable with changes by primary AlSi9Cu3 cast alloy.

Effects of Homogenization on Microstructures and Mechanical Properties of as Cast AZ91 Mg Alloy

2011 ◽  
Vol 217-218 ◽  
pp. 1123-1128
Author(s):  
Jun Wei Liu ◽  
Shi Qiang Lu ◽  
Xian Juan Dong ◽  
Xuan Xiao
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Microstructural Evolution ◽  
Peak Stress ◽  
Mg Alloy ◽  
Second Phase ◽  
Compression Process ◽  
Heat Treated ◽  
Microstructures And Mechanical Properties

The microstructural evolution and mechanical properties of as cast AZ91 Mg alloy enduring different homogenization conditions were researched. The results show that the peak stress and plasticity obtain improvement with the increase of heat treated time and temperature until 693K. When the temperature is higher than 743K, the sample will occur the over-burned and directly lead to the decrease of mechanical properties. Otherwise, with the increase of heat treated time and temperatures, the second phase gradually precipitate from the solution, while the grain evolution is not obvious. In the compression process for the samples after heat treatment, some twins could be found in the grains.

Sign in / Sign up

Export Citation Format

Share Document