Effects of Homogenization on Microstructures and Mechanical Properties of as Cast AZ91 Mg Alloy

2011 ◽  
Vol 217-218 ◽  
pp. 1123-1128
Author(s):  
Jun Wei Liu ◽  
Shi Qiang Lu ◽  
Xian Juan Dong ◽  
Xuan Xiao
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Microstructural Evolution ◽  
Peak Stress ◽  
Mg Alloy ◽  
Second Phase ◽  
Compression Process ◽  
Heat Treated ◽  
Microstructures And Mechanical Properties

The microstructural evolution and mechanical properties of as cast AZ91 Mg alloy enduring different homogenization conditions were researched. The results show that the peak stress and plasticity obtain improvement with the increase of heat treated time and temperature until 693K. When the temperature is higher than 743K, the sample will occur the over-burned and directly lead to the decrease of mechanical properties. Otherwise, with the increase of heat treated time and temperatures, the second phase gradually precipitate from the solution, while the grain evolution is not obvious. In the compression process for the samples after heat treatment, some twins could be found in the grains.

Microstructural Evolution and Mechanical Properties of Modified 9%Cr-1%Mo Steel upon Isothermal Heat-Treatment

2005 ◽  
Vol 475-479 ◽  
pp. 81-84
Author(s):  
Sung Kang Hur ◽  
Kee Sam Shin ◽  
Jung Hoon Yoo ◽  
Ja Min Koo ◽  
Soo Lee ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Mechanical Property ◽  
Microstructural Evolution ◽  
Heat Treating ◽  
Air Cooling ◽  
Isothermal Heat Treatment ◽  
Martensitic Structure ◽  
Heat Treated ◽  
Evolution Of Microstructure

The evolution of microstructure and its effects on the mechanical properties of modified 9%Cr-1%Mo steel during heat-treating at 1050°C for 15 min and then isothermal heat treatment at 380~760°C with subsequent air-cooling have been investigated. For the microstructural and mechanical property analyses, OM, SEM, EDS, XRD, hardness and impact tests were used. In accordance with the severity of the heat-treatment, the microstructure evolved from the untransformed martensite to the partially transformed dual phases of martensite and ferrite, and then fully transformed to ferrite. Impact values at ambient temperature for specimens isothermally heat-treated at 320 - 380°C, predominantly at about 350°C were lower than others’ with similar martensitic structure. The partially transformed specimens with dual phases of martensite and ferrite also showed lower impact values than samples with untransformed with martensitic, and transformed with ferritic structures.

Tensile Properties of Friction Stir Welded AZ31B Mg Alloy

2007 ◽  
Vol 124-126 ◽  
pp. 1357-1360
Author(s):  
Seon Mi Ha ◽  
Sang Shik Kim ◽  
Dong Yim Chang ◽  
Chang Gil Lee ◽  
Sung Joon Kim
Keyword(s):  
Heat Treatment ◽  
Tensile Properties ◽  
Microstructural Evolution ◽  
Tensile Ductility ◽  
Tensile Behavior ◽  
Mg Alloy ◽  
Reduction Mechanism ◽  
Friction Stir ◽  
Heat Treated ◽  
Optical Micrographs

The effect of prior T4 heat treatment and subsequent microstructural evolution on tensile behavior of friction stir welded (FSWed) AZ31B-H24 alloy was examined in this study. Selected AZ31B-H24 plates were prior T4 heat treated at 400 for 24 hours and subsequently friction stir welded. The tensile properties, optical micrographs and SEM fractographs for FSWed AZ31B-T4 specimens were compared with those for the H24 counterparts. Prior T4 heat treatment tended to decrease the tensile ductility reduction in FSWed AZ31B-H24 specimen. The tensile ductility reduction mechanism as associated with prior T4 heat treatment is discussed based on detailed micrographic and fractographic observations.

scholarly journals Effect of Heat Treatment on the Microstructure, Phase Distribution, and Mechanical Properties of AlCoCuFeMnNi High Entropy Alloy

2017 ◽  
Vol 2017 ◽  
pp. 1-6 ◽  
Author(s):  
Gulhan Cakmak
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Yield Strength ◽  
Phase Distribution ◽  
Cast Alloy ◽  
Lattice Parameters ◽  
High Entropy Alloy ◽  
Second Phase ◽  
High Entropy ◽  
Heat Treated

The present paper reports the synthesis of AlCoCuFeMnNi high entropy alloy (HEA) with arc melting process. The as-cast alloy was heat treated at 900°C for 8 hours to investigate the effect of heat treatment on the structure and properties. Microstructural and mechanical properties of the alloy were analyzed together with the detailed phase analysis of the samples. The initially as-cast sample was composed of two separate phases with BCC and FCC structures having lattice parameters of 2.901 Å and 3.651 Å, respectively. The heat-treated alloy displays microsized rod-shaped precipitates both in the matrix and within the second phase. Rietveld refinement has shown that the structure was having three phases with lattice parameters of 2.901 Å (BCC), 3.605 Å (FCC1), and 3.667 Å (FCC2). The resulting phases and distribution of phases were also confirmed with the TEM methods. The alloys were characterized mechanically with the compression and hardness tests. The yield strength, compressive strength, and Vickers hardness of the as-cast alloy are 1317 ± 34 MPa, 1833 ± 45 MPa, and 448 ± 25 Hv, respectively. Heat treatment decreases the hardness values to 419 ± 26 Hv. The maximum compressive stress of the alloy increased to 2123 + 41 MPa while yield strength decreased to 1095 ± 45 with the treatment.

Effect of post-heat treatment on microstructure and mechanical properties of laser welded Al-Cu-Mg alloy

2021 ◽  
Vol 64 ◽  
pp. 620-632
Author(s):  
Alexander Malikov ◽  
Anatoly Orishich ◽  
Igor Vitoshkin ◽  
Evgeniy Karpov ◽  
Alexei Ancharov
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Mg Alloy ◽  
Post Heat Treatment ◽  
Microstructure And Mechanical Properties

scholarly journals Influence of Post Weld Heat Treatment on the Grain Size, and Mechanical Properties of the Alloy-800H Rotary Friction Weld Joints

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4366
Author(s):  
Saqib Anwar ◽  
Ateekh Ur Rehman ◽  
Yusuf Usmani ◽  
Ali M. Al-Samhan
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Heat Affected Zone ◽  
Tensile Testing ◽  
Weld Zone ◽  
Alloy 800H ◽  
Weld Joints ◽  
Heat Treated ◽  
Friction Weld

This study evaluated the microstructure, grain size, and mechanical properties of the alloy 800H rotary friction welds in as-welded and post-weld heat-treated conditions. The standards for the alloy 800H not only specify the composition and mechanical properties but also the minimum grain sizes. This is because these alloys are mostly used in creep resisting applications. The dynamic recrystallization of the highly strained and plasticized material during friction welding resulted in the fine grain structure (20 ± 2 µm) in the weld zone. However, a small increase in grain size was observed in the heat-affected zone of the weldment with a slight decrease in hardness compared to the base metal. Post-weld solution heat treatment (PWHT) of the friction weld joints increased the grain size (42 ± 4 µm) in the weld zone. Both as-welded and post-weld solution heat-treated friction weld joints failed in the heat-affected zone during the room temperature tensile testing and showed a lower yield strength and ultimate tensile strength than the base metal. A fracture analysis of the failed tensile samples revealed ductile fracture features. However, in high-temperature tensile testing, post-weld solution heat-treated joints exhibited superior elongation and strength compared to the as-welded joints due to the increase in the grain size of the weld metal. It was demonstrated in this study that the minimum grain size requirement of the alloy 800H friction weld joints could be successfully met by PWHT with improved strength and elongation, especially at high temperatures.

Application of Tailored Heat Treated Blanks under Quasi Series Conditions

2007 ◽  
Vol 344 ◽  
pp. 383-390 ◽  
Author(s):  
Marion Merklein ◽  
Uwe Vogt
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Local Heat ◽  
Strength Distribution ◽  
Process Window ◽  
Short Term ◽  
Forming Process ◽  
Heat Treated ◽  
Set Up ◽  
The Impact

Tailored Heat Treated Blanks (THTB) are blanks that exhibit locally different strength specifically optimized for the succeeding forming process. The strength distribution is set by a local, short-term heat treatment modifying the mechanical properties of the material. Hence, THTB allow enhancing forming limits significantly leading to shorter and more robust manufacture process chains. In order to qualify the use of THTB under quasi series conditions, the interdependencies of the blank’s local heat treatment and the entire process chain of the car body manufacture have to be analyzed. In this respect, the impact of a short-term heat treatment on the mechanical properties of AA6181PX, a commonly used aluminum alloy in today’s car bodies, was studied. Also the influence of a short-term heat treatment on the coil lubricant, usually already applied by the material supplier, was given a closer look. Based on these experiments process restrictions for the application of THTB in an industrial automotive environment were derived and a process window for the THTB design was set up. In conclusion, strategies were defined how to enhance the found process boundaries leading to a more robust process window.

Effect of heat treatment on mechanical properties of 3D printed polylactic acid parts

2021 ◽  
Vol 63 (1) ◽  
pp. 73-78
Author(s):  
Pulkin Gupta ◽  
Sudha Kumari ◽  
Abhishek Gupta ◽  
Ankit Kumar Sinha ◽  
Prashant Jindal
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Polylactic Acid ◽  
Recrystallization Temperature ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Dog Bone ◽  
Heat Treated ◽  
Maximum Decrease ◽  
3D Printed

Abstract Fused deposition modelling (FDM) is a layer-by-layer manufacturing process type of 3D-printing (3DP). Significant variation in the mechanical properties of 3D printed specimens is observed because of varied process parameters and interfacial bonding between consecutive layers. This study investigates the influence of heat treatment on the mechanical strength of FDM 3D printed Polylactic acid (PLA) parts with constant 3DP parameters and ambient conditions. To meet the objectives, 7 sets, each containing 5 dog-bone shaped samples, were fabricated from commercially available PLA filament. Each set was subjected to heat treatment at a particular temperature for 1 h and cooled in the furnace itself, while one set was left un-treated. The temperature for heat treatment (Th) varied from 30 °C to 130 °C with increments of 10 °C. The heat-treated samples were characterized under tensile loading of 400 N and mechanical properties like Young’s modulus (E), Strain % ( ε ) and Stiffness (k) were evaluated. On comparing the mechanical properties of heat-treated samples to un-treated samples, significant improvements were observed. Heat treatment also altered the geometries of the samples. Mechanical properties improved by 4.88 % to 10.26 % with the maximum being at Th of 110 °C and below recrystallization temperature (Tr) of 65 °C. Deformations also decreased significantly at higher temperatures above 100 °C, by a maximum of 36.06 %. The dimensions of samples showed a maximum decrease of 1.08 % in Tr range and a maximum decrease of 0.31 % in weight at the same temperature. This study aims to benefit the society by establishing suitable Th to recover the lost strength in PLA based FDM 3D printed parts.

Influence of Heat Treatment on Microstrudture and Mechanical Properties of AZ31B Magnesium Alloy Prepared by Solid-State Recycling

2012 ◽  
Vol 271-272 ◽  
pp. 17-20
Author(s):  
Shu Yan Wu ◽  
Ze Sheng Ji ◽  
Chun Ying Tian ◽  
Ming Zhong Wu
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid State ◽  
Magnesium Alloy ◽  
Static Recrystallization ◽  
Annealing Treatment ◽  
Az31b Magnesium Alloy ◽  
Heat Treated ◽  
Elongation To Failure ◽  
Strength And Ductility

This work is to study the influence of heat treatment on microstrudture and mechanical properties of AZ31B magnesium alloy prepared by solid -state recycling. AZ31B magnesium alloy chips were recycled by hot extruding. Three different heat treatments were conducted for recycled alloy. Mechanical properties and microstructure of the recycled specimen and heat treated specimen were investigated. 300°C×2h annealing specimen exhibits finer grain due to static recrystallization, and microstructure of 400°C×2h annealing specimen becomes more coarse. 300°C×2h annealing treatment improves obviously strength and ductility of recycled alloy. Ultimate tensile strength of alloy decreases and elongation to failure increases after 400°C×2h annealing. Grain size, dislocation density and bonding of chips have an effect on the elongation of recycled materials. 190°C×8h ageing has no influence on microstructure and mechanical properties of recycled alloy.

Sign in / Sign up

Export Citation Format

Share Document