scholarly journals The Assessment of Strength of Cementitious Materials Impregnated Using Hydrophobic Agents Based on Near-Surface Hardness Measurements

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4583
Author(s):  
Martyna Nieświec ◽  
Łukasz Sadowski
Keyword(s):  
Compressive Strength ◽  
Cement Paste ◽  
Concrete Structures ◽  
Surface Hardness ◽  
Cementitious Materials ◽  
Schmidt Hammer ◽  
Near Surface ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
The Impact

Recently, the surfaces of concrete structures are impregnated to protect them against the environment in order to increase their durability. It is still not known how the use of these agents affects the near-surface hardness of concrete. This is especially important for experts who use the near-surface hardness of concrete for estimating its compressive strength. The impregnation agents are colorless and, thus, without knowledge of their use, mistakes can be made when testing the surface hardness of concrete. This paper presents the results of investigations concerning the impact of impregnation on the subsurface hardness concrete measured using a Schmidt hammer. For this research, samples of cement paste with a water–cement ratio of 0.4 and 0.5 were used. The samples were impregnated with one, two, and three layers of two different agents. The first agent has been made based on silanes and siloxanes and the second agent has been made based on based on polymers. The obtained research results allow for the conclusion that impregnation affects the near-surface hardness of concrete. This research highlights the fact that a lack of knowledge about the applied impregnation of concrete when testing its near-surface hardness, which is then translated into its compressive strength, can lead to serious mistakes.

Research of Performance of Low Amount of Cement Manufactured-Sand Concrete

2013 ◽  
Vol 357-360 ◽  
pp. 1200-1205
Author(s):  
Chun Hui Yu ◽  
Gu Hua Li ◽  
Jin Liang Gao ◽  
Qun Wei ◽  
Da Zhen Xu
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Grain Shape ◽  
Great Influence ◽  
Cementitious Materials ◽  
Natural Sand ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Manufactured Sand

Compared with natural sand, manufactured-sand is of small porosity, poor grain shape and graded, which impacts mixes workability and the properties after hardening. In Concrete, playing the role of retaining moisture water is mainly powder, including cement, powder in the sand and fly ash etc. The amount of powder has a great influence on the properties of concrete, especially on its workability. This paper mainly discusses the influence of amount of cement, cementitious materials, fly ash, water-cement ratio and other factors on the workability, compressive strength and shrinkage of concrete. The experiments show that, in the case of the low amount of cement, workability of the manufactured-sand concrete mixture, compressive strength and shrinkage deformation of test block all meet the actual requirements.

Effect of Admixed Recycled Aggregate on Properties of Recycled Concrete

2012 ◽  
Vol 174-177 ◽  
pp. 743-746
Author(s):  
Ya Jun Zhao ◽  
Ying Gao ◽  
Li Li He
Keyword(s):  
Compressive Strength ◽  
Design Method ◽  
Orthogonal Design ◽  
Plain Concrete ◽  
Recycled Concrete ◽  
Recycled Aggregate ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Influence Of Water ◽  
The Impact

The mixture proportion of recycled concrete was discussed by orthogonal design method. The influence of water-cement ratio, recycled aggregate quantity on workability, cube compressive strength of recycled concrete was analyzed. The experimental results indicated that，Recycled concrete mix proportion design should consider the impact of the water absorption of recycled aggregate. Unit water amount of recycled concrete should be plain concrete unit water consumption and recycled aggregate additional amount of water. Sand ratio should increase in the corresponding ordinary aggregate concrete sand ratio on the basis of 1 to 3 percent. When the water-cement ratio is 0.36 and construction waste content of 40% slag content of 20%, 28d compressive strength of concrete is 48.1MPa, slightly higher than the reference concrete (48.0MPa).

Study of Manufacture Process and Properties of Tailings and Slag Based Mine Filling Cementitious Materials

2013 ◽  
Vol 734-737 ◽  
pp. 1077-1081 ◽  
Author(s):  
Jin Xia Zhang ◽  
Shu Xian Liu ◽  
Jun Xie
Keyword(s):  
Compressive Strength ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Raw Materials ◽  
Cementitious Materials ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Manufacture Process ◽  
Alkali Activated

The tailings and slag based mine filling cementitious materials was prepared by sodium silicate and sodium hydroxide alkali-activated tailings and slag. Through the test that the cementing materials in the best ratio of raw materials: when slag and tailings admixture is 1.25, the content of NaOH was 50%, the amount of sodium hydroxide for 50%, water cement ratio of 0.22, under the condition of normal temperature curing 7 days, eventually making a compressive strength of 52.3MPa cementing materials.

scholarly journals Effects of Using Silica Fume and Polycarboxylate-Type Superplasticizer on Physical Properties of Cementitious Grout Mixtures for Semiflexible Pavement Surfacing

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Suhana Koting ◽  
Mohamed Rehan Karim ◽  
Hilmi Mahmud ◽  
Nuha S. Mashaan ◽  
Mohd Rasdan Ibrahim ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Silica Fume ◽  
High Strength ◽  
Flexible Pavement ◽  
Cementitious Materials ◽  
Flow Properties ◽  
Cement Ratio ◽  
Paired Sample ◽  
Water Cement Ratio ◽  
Porous Pavement

Semi-flexible pavement surfacing is a composite pavement that utilizes the porous pavement structure of the flexible bituminous pavement, which is subsequently grouted with appropriate cementitious materials. This study aims to investigate the compressive strength, flexural strength, and workability performance of cementitious grout. The grout mixtures are designed to achieve high strength and maintain flow properties in order to allow the cement slurries to infiltrate easily through unfilled compacted skeletons. A paired-samplet-test was carried out to find out whether water/cement ratio, SP percentages, and use of silica fume influence the cementitious grout performance. The findings showed that the replacement of 5% silica fume with an adequate amount of superplasticizer and water/cement ratio was beneficial in improving the properties of the cementitious grout.

Pastes Prepared with Sulfonate, Chalcedony and Sugar

2012 ◽  
Vol 517 ◽  
pp. 338-341
Author(s):  
Ulisses Targino Bezerra ◽  
Normando Perazzo Barbosa
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Compression Strength ◽  
Cementitious Materials ◽  
Important Conclusion ◽  
Cement Pastes ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Good Workability ◽  
Portland Cement Paste

Papers presented at ICPIC 2010, Madeira Island, Portugal, dealing with the use of polymers in cementitious materials, show the need to combine different admixtures to optimize the properties of cement. This work is a continuation of a paper presented at NOCMAT 2010, Cairo-Egypt, about the incorporation of several materials in Portland cement to increase mechanical properties and workability. The best performance admixtures were chosen and they were combined considering the superposition of effects. Cement pastes were prepared with chalcedony and sulfonate (to increase compressive strength) and sugar (to increase workability). Two percent of cement was replaced by the admixtures. The water/cement ratio was constant and equal to 0.44. Results show that the combination of 0.05% of sugar and 1.95% of sulfonate and 0.10% of sugar and 1.90% of chalcedony produced a paste with the greatest compressive strength and good workability. Compression strength was respectively 27.4 MPa and 36.6 MPa, which represent increases of 33.5% and 78.6%, respectively, relative to the reference paste without admixtures. While increasing the paste compression strength with sulfonate has been significant, the results of the paste with chalcedony were the more surprising because the water/cement ratio of pastes was kept constant. The chalcedony is a type of crystalline silica, which shows deformation in their structure. So because of crystalline structure of chalcedony, there should be, probably, no significant reactivity of it with the cement hydrates, just the fact that its structure be deformed can explain this reactivity. The most important conclusion concerns is that the combinations of admixtures can improve a lot the properties of Portland cement paste.

scholarly journals A new approach to estimate compressive strength of concrete by the UPV method

2016 ◽  
Vol 9 (3) ◽  
pp. 395-402 ◽  
Author(s):  
M. A. P. Irrigaray ◽  
R. C. de A. Pinto ◽  
I. J. Padaratz
Keyword(s):  
Compressive Strength ◽  
Cement Paste ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Concrete Compressive Strength ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Concrete Mixtures ◽  
Unique Relationship

ABSTRACT Although the ultrasonic pulse velocity (UPV) method has been extensively used to estimate concrete compressive strength, the relationship between UPV and concrete strength is mixture dependent. As a result, the applicability of this method to estimate strength is well known to be limited. Aggregate type, cement type, mixture proportions, and water-cement ratio influence such a relationship. Nevertheless, UPV and strength are both governed by cement hydration, and thus, a relationship between UPV in the cement paste phase and concrete compressive strength would be expected to exist. By not taking into account the type and volume content of aggregates, this relationship could be the same for concrete mixtures with same type of cement and water-cement ratio, regardless the aggregate type used. This study investigates the existence of such a relationship. Concrete mixtures with water-cement ratios of 0.48, 0.55 and 0.64, with different paste volumes were prepared in the laboratory. For each mixture, compressive strength and ultrasonic pulse velocity were evaluated at various ages. The UPV of each concrete phase: paste, fine aggregate, and coarse aggregate, was obtained through paste and mortar specimens. This study indicated that it is possible to establish a unique relationship between the UPV in cement paste phase and the concrete compressive strength. This unique relationship could be applied to several concrete mixtures, greatly expanding the use of the UPV method to estimate compressive strength.

scholarly journals Investigations of the Influence of Polystyrene Foamed Granules on the Properties of Lightweight Concrete

2019 ◽  
Vol 9 (1) ◽  
pp. 19-24 ◽  
Author(s):  
Suman Kumar Adhikary ◽  
Zymantas Rudzionis ◽  
Marijus Zubrus
Keyword(s):  
Compressive Strength ◽  
Cement Paste ◽  
Lightweight Concrete ◽  
Microscopic Analysis ◽  
Hydrated Lime ◽  
Curing Process ◽  
Polystyrene Foam ◽  
Cement Pastes ◽  
Cement Ratio ◽  
Water Cement Ratio

Abstract This paper deals with the behaviour of cement paste upon the addition of crushed polystyrene foam. Crushed polystyrene foam waste with a fill density of 13.97 kg/m3 and hydrated lime were used to prepare the foam. Three different types of samples S-1, S-2, and S-3 were prepared to observe the behaviour of cement pastes after the addition of different doses of foam in constant water/cement ratio. The volumetric ratio of EPS and cement paste were 1: 1.294; 1: 0.863; and 1: 0.647. In each type of sample, 0.28 water/cement ratio is maintained. Slump test was carried out in the fresh state and it has been found slump value was decreasing by increasing foam content in concrete sample. On the 7th and 28th day of curing process, the compressive strength test was carried out. Compressive strength and density of concrete samples also decreasing by addition of higher foam content. In addition, water absorption test and microscopic analysis tests were carried out on the 28th day of curing process. It has been found from the study that samples thermal conductivity is working proportionally.

Probabilistic Modelling and the k-Value Concept

2014 ◽  
Vol 635 ◽  
pp. 198-203
Author(s):  
Břetislav Teplý ◽  
Markéta Chromá ◽  
Pavla Rovnaníková ◽  
Alfred Strauss
Keyword(s):  
Mathematical Models ◽  
Concrete Structures ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Probabilistic Modelling ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Class A ◽  
Durability Assessment ◽  
Value Concept

The durability of concrete structures is an important issue. Eurocode EN 206-1 introduces the k-value concept for concretes made with supplementary cementitious materials; a prescriptive concept that recommends limiting water/cement ratio values for a specified exposure class. A more advanced performance-based concept directly requires that concrete be designed in terms of performance-related parameters, an approach which seems to be more suitable when durability must be achieved. The application of mathematical models in durability assessment is advocated, and an example is shown.

scholarly journals Fluidity Influencing Factors Analysis and Ratio Optimization of New Sealing Materials Based on Response Surface Method

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Xin Guo ◽  
Sheng Xue ◽  
Yaobin Li ◽  
Chunshan Zheng ◽  
Gege Yang
Keyword(s):  
Compressive Strength ◽  
Setting Time ◽  
Expansion Rate ◽  
Key Factors ◽  
Gas Drainage ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Sealing Material ◽  
The Impact ◽  
Sealing Materials

The borehole sealing material is one of the key factors affecting the gas drainage effect of a borehole. This paper takes the compressive strength, fluidity, expansion rate, and setting time of the sealing material as the main research indicators and explores the influence of each key influencing factor on the performance of the high-fluid sealing material through the single factor experiment method. Using the Design-Expert 8.0.5 Trial software designed orthogonal experiments and establishing a quadratic model between liquidity and each test factor, which showed the impact of each key factor on the fluidity. Finally, by adjusting the amount of admixtures, the optimal ratio of high-fluidity borehole sealing materials was obtained. The results showed that the key factors had the following order of significance: water – cement   reducing   agent > water – cement   ratio > retarder > expansion   agent . With the water-cement ratio and the amount of water reducing agent increase, the fluidity of the material will increase; and with the increase of the retarder and expansion agent, the fluidity will decrease. In actual use, the fluidity is the main factor, but the expansion rate, compressive strength, and setting time are also considered. The optimal percentages were found for the high-fluidity borehole sealing material: a water-cement ratio of 1, along with 0.03% retarder, 0.5% water reducer, and 8% expansion agent. These research results could provide a reference for improving the performance of gas drainage borehole sealing materials and enhancing the effect of gas drainage.

scholarly journals Use of Nondestructive Testing of Ultrasound and Artificial Neural Networks to Estimate Compressive Strength of Concrete

Buildings ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 44
Author(s):  
Fernando A. N. Silva ◽  
João M. P. Q. Delgado ◽  
Rosely S. Cavalcanti ◽  
António C. Azevedo ◽  
Ana S. Guimarães ◽  
...  
Keyword(s):  
Neural Networks ◽  
Compressive Strength ◽  
Artificial Neural Networks ◽  
Cross Sections ◽  
Influential Factors ◽  
Average Error ◽  
Ann Model ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Artificial Neural

The work presents the results of an experimental campaign carried out on concrete elements in order to investigate the potential of using artificial neural networks (ANNs) to estimate the compressive strength based on relevant parameters, such as the water–cement ratio, aggregate–cement ratio, age of testing, and percentage cement/metakaolin ratios (5% and 10%). We prepared 162 cylindrical concrete specimens with dimensions of 10 cm in diameter and 20 cm in height and 27 prismatic specimens with cross sections measuring 25 and 50 cm in length, with 9 different concrete mixture proportions. A longitudinal transducer with a frequency of 54 kHz was used to measure the ultrasonic velocities. An ANN model was developed, different ANN configurations were tested and compared to identify the best ANN model. Using this model, it was possible to assess the contribution of each input variable to the compressive strength of the tested concretes. The results indicate an excellent performance of the ANN model developed to predict compressive strength from the input parameters studied, with an average error less than 5%. Together, the water–cement ratio and the percentage of metakaolin were shown to be the most influential factors for the compressive strength value predicted by the developed ANN model.

Sign in / Sign up

Export Citation Format

Share Document