scholarly journals Effect of Fiber Shape on the Tribological, Mechanical, and Morphological Behaviors of Sisal Fiber-Reinforced Resin-Based Friction Materials: Helical, Undulated, and Straight Shapes

Materials ◽  
2021 ◽  
Vol 14 (18) ◽  
pp. 5410
Author(s):  
Siyang Wu ◽  
Jiale Zhao ◽  
Mingzhuo Guo ◽  
Jian Zhuang ◽  
Qian Wu
Keyword(s):  
Composite Materials ◽  
Sisal Fiber ◽  
High Recovery ◽  
Promising Candidate ◽  
Different Shapes ◽  
Fiber Matrix Interface ◽  
Sisal Fibers ◽  
The Impact ◽  
Adhesion Condition ◽  
Shaped Fibers

In this paper, we aim to evaluate the tribological, mechanical, and morphological performance of resin-based friction composites reinforced by sisal fibers with different shapes, namely helical, undulated, and straight shapes. The experimental results show that the shape of the sisal fibers exerts a significant effect on the impact property of the composite materials but no obvious influence on the density and hardness. The friction composite containing the helical-shaped sisal fibers exhibits the best overall tribological behaviors, with a relatively low fade (9.26%), high recovery (98.65%), and good wear resistance (2.061 × 10−7 cm3∙N−1∙m−1) compared with the other two composites containing undulated-shaped fibers and straight-shaped fibers. The impact fracture surfaces and worn surfaces of the composite materials were inspected by scanning electron microscopy, and we demonstrate that adding helical-shaped sisal fibers into the polymer composites provides an enhanced fiber–matrix interface adhesion condition and reduces the extent of fiber debonding and pullout, effectively facilitating the presence of more secondary plateaus on the friction surface, which are responsible for the enhanced tribological and mechanical properties. The outcome of this study reveals that sisal fibers with a helical shape could be a promising candidate as a reinforcement material for resin-based brake friction composite applications.

Effects of Weave Type and Fiber Content on Physical Properties of Sisal Fiber/Epoxy Composites

2010 ◽  
Vol 123-125 ◽  
pp. 1139-1142 ◽  
Author(s):  
Sawitri Srisuwan ◽  
Pranee Chumsamrong
Keyword(s):  
Impact Strength ◽  
Physical Properties ◽  
Epoxy Resin ◽  
Flexural Modulus ◽  
Fiber Content ◽  
Epoxy Composites ◽  
Sisal Fiber ◽  
Pure Epoxy ◽  
Sisal Fibers ◽  
The Impact

In this study, the effects of weave type and fiber content on the physical properties of woven sisal fiber/epoxy composites were investigated. Sisal fibers used in this work were obtained from Nakhon Ratchasima, Thailand. Both untreated and alkali-treated fibers were employed. The woven sisal fibers were manufactured by hand weaving process. The fiber content in sisal fiber/epoxy composites were 3 wt.%, 5 wt.% and 10 wt.%. The composites were cured at room temperatures. In order to determine mechanical properties of the composites, flexural and impact tests were applied. Flexural strength and flexural modulus of all composites were higher than those of pure epoxy resin and tended to increase with increasing fiber content. The impact strength of all composites was lower than that of pure epoxy resin. The composites containing 10 wt.% sisal fibers showed the highest impact strength. There was no definite influence of weave type on flexural properties of the composites. At 3 and 5 wt.% fiber, the composites containing plain weave fibers seemed to show a higher impact strength than the composites containing other weave types.

scholarly journals Bio-Based Polyurethane Composites and Hybrid Composites Containing a New Type of Bio-Polyol and Addition of Natural and Synthetic Fibers

Materials ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2028 ◽  
Author(s):  
Adam Olszewski ◽  
Paulina Kosmela ◽  
Aleksandra Mielewczyk-Gryń ◽  
Łukasz Piszczyk
Keyword(s):  
Hybrid Composites ◽  
Sem Analysis ◽  
Sisal Fiber ◽  
Synthetic Fibers ◽  
The Matrix ◽  
New Type ◽  
Liquefaction Process ◽  
Sisal Fibers ◽  
Polyurethane Composites ◽  
The Impact

This article describes how new bio-based polyol during the liquefaction process can be obtained. Selected polyol was tested in the production of polyurethane resins. Moreover, this research describes the process of manufacturing polyurethane materials and the impact of two different types of fibers—synthetic and natural (glass and sisal fibers)—on the properties of composites. The best properties were achieved at a reaction temperature of 150 °C and a time of 6 h. The hydroxyl number of bio-based polyol was 475 mg KOH/g. Composites were obtained by hot pressing for 15 min at 100 °C and under a pressure of 10 MPa. Conducted researches show the improvement of flexural strength, impact strength, hardness, an increase of storage modulus of obtained materials, and an increase of glass transition temperature of hard segments with an increasing amount of fibers. SEM analysis determined better adhesion of sisal fiber to the matrix and presence of cracks, holes, and voids inside the structure of composites.

scholarly journals Impact resistance of sisal fiber reinforced concrete

2018 ◽  
Vol 7 (2) ◽  
pp. 742
Author(s):  
Sabapathy Y K ◽  
Ramya Sajeevan ◽  
Rekha J ◽  
Vishal V ◽  
Sabarish S ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Impact Load ◽  
Impact Resistance ◽  
Fiber Reinforced Concrete ◽  
Sisal Fiber ◽  
Impact Loads ◽  
Fiber Reinforced ◽  
Impact Machine ◽  
Sisal Fibers ◽  
The Impact

Concrete is typically a brittle material which is prone to damage when subjected to heavy impact loads. To overcome this weakness, concrete is reinforced with fibers as fibers are effective in withstanding heavy impact loads. The main objective of this experimental investigation is to study the influence of sisal fibers in concrete under impact load. The impact specimens are prepared using three grades of concrete- M20, M30 and M40 with five varying percentage of fibers- 0%, 0.5%, 1%, 1.5% and 2%. The mix designs of the respective grades of concrete are made as per the Indian standards. The specimens after curing for 28 days were subjected to impact loads using the standard drop weight impact machine confining to ASTM standards. Also cube and cylinder specimens are prepared and tested to ascertain the compressive and tensile strength of the sisal fiber reinforced concrete. The results indicated that the sisal fibers are effective in increasing the impact strength of concrete.

scholarly journals MECHANICAL PROPERTIES OF THE VIET NAM SISAL FIBRE REINFORCED POLYPROPYLENE COMPOSITE

2011 ◽  
Vol 14 (2) ◽  
pp. 29-36
Author(s):  
Nieu Huu Nguyen ◽  
Binh Thanh Phan ◽  
Sau Huynh
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Loss Modulus ◽  
Flexural Modulus ◽  
Dynamic Mechanical Properties ◽  
Sisal Fiber ◽  
Sisal Fibre ◽  
Dynamic Mechanical ◽  
Sisal Fibers ◽  
The Impact

The static mechanical and dynamic mechanical properties of the treated sisal fiber reinforced polypropylene composites were improved by adding the compatiblizer PPgMA (polypropylene-grafted-maleic anghydride). The mechanical properties of the composites have been evaluated. By increasing PPgMA dosages from 2% and 3.5% by weight of PP matrix; the impact strength of the composites were significantly improved by 27% and 38%; the elongation increased by 21% and 36%; the tensile strength increased by 35% and 95%; the elastic modulus increased by 21% and 94% and the flexural modulus increased by 2% and 83% respectively. The dynamic mechanical properties (the storage modulus E’, the loss modulus E” and the loss factor tanδ) have been investigated in relation to the compatibility between the PP matrix and the treated sisal fibers. E’ and E” increased by increasing dosage of PPgMA and Tg decreased a little when increasing the contents of PPgMA. At higher temperatures, tanδ increased and at lower temperature tanδ decreased when increasing dosage of PPgMA. It is shown that PP/treated sisal fibers/PPgMA composites have shown the effects of cohesion when increasing the PPgMA. The fiber dispersion was studied by the transmission optical microscope (TOM). The morphology of the composites samples fractured by the impact strength tests have been studied using scanning electronic microscopy (SEM). The results show the improvement of the interaction forces between treated sisal fibers and PP matrix at higher levels of PPgMA.

scholarly journals Impact of microorganisms on mechanical properties changes of composite materials with organic filler

2021 ◽  
Author(s):  
Jarosław Szuszkiewicz
Keyword(s):  
Composite Materials ◽  
Impact Strength ◽  
Rapid Development ◽  
Fungal Spores ◽  
Polymer Materials ◽  
Sisal Fiber ◽  
Processing Temperature ◽  
Natural Conditions ◽  
Research Results ◽  
The Impact

The beginning of the XXIst century is characterized by rapid development of polymer materials, including polymer composite materials, which consist of a natural organic filler (wood flour, sawdust, cellulose fiber, flax fiber, sisal fiber) and reinforcement carrier. In case of that kind of the fillers under the influence of weathering (humidity, temperature) they might be subject to biodegradation due to effect of microorganisms, including funguses, which are responsible for degradation of natural organic fillers. In case of the low melting temperature polymers (e.g. PE-LD) the processing temperature does not entirely eliminate some of the fungal spores. The paper has presented the research results of twelve months. The development of the microorganisms in the natural conditions was examined in a pure filler (sawdust) as well as in a composite. Simultaneously, change of one of the fundamental strength properties, which is the impact strength, was being tested. For the investigated composite the PE-LD as the matrix and a sawdust mixture of pine, larch and oak were used. The sawdust formed the composite in 30 %. The research results confirmed that in the natural conditions the microorganisms development depends on weathering which varies in the time of the year. The value of the V notch impact strength changed from 12.5 kJ/m2 for the composite in initial phase to the value of 6.7 kJ/m2 after twelve months operation, which is 50 %.

scholarly journals The Effect of Superabsorbent Polymers on the Microstructure and Self-Healing Properties of Cementitious-Based Composite Materials

2021 ◽  
Vol 11 (2) ◽  
pp. 700
Author(s):  
Irene A. Kanellopoulou ◽  
Ioannis A. Kartsonakis ◽  
Costas A. Charitidis
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Hybrid Structure ◽  
The Self ◽  
Self Healing ◽  
Cementitious Composite ◽  
Superabsorbent Polymers ◽  
Porosity Reduction ◽  
Environment Control ◽  
The Impact

Cementitious structures have prevailed worldwide and are expected to exhibit further growth in the future. Nevertheless, cement cracking is an issue that needs to be addressed in order to enhance structure durability and sustainability especially when exposed to aggressive environments. The purpose of this work was to examine the impact of the Superabsorbent Polymers (SAPs) incorporation into cementitious composite materials (mortars) with respect to their structure (hybrid structure consisting of organic core—inorganic shell) and evaluate the microstructure and self-healing properties of the obtained mortars. The applied SAPs were tailored to maintain their functionality in the cementitious environment. Control and mortar/SAPs specimens with two different SAPs concentrations (1 and 2% bwoc) were molded and their mechanical properties were determined according to EN 196-1, while their microstructure and self-healing behavior were evaluated via microCT. Compressive strength, a key property for mortars, which often degrades with SAPs incorporation, in this work, practically remained intact for all specimens. This is coherent with the porosity reduction and the narrower range of pore size distribution for the mortar/SAPs specimens as determined via microCT. Moreover, the self-healing behavior of mortar-SAPs specimens was enhanced up to 60% compared to control specimens. Conclusively, the overall SAPs functionality in cementitious-based materials was optimized.

scholarly journals Research on a Rice Counting Algorithm Based on an Improved MCNN and a Density Map

Entropy ◽  
2021 ◽  
Vol 23 (6) ◽  
pp. 721
Author(s):  
Ao Feng ◽  
Hongxiang Li ◽  
Zixi Liu ◽  
Yuanjiang Luo ◽  
Haibo Pu ◽  
...  
Keyword(s):  
Grain Weight ◽  
Gaussian Kernel ◽  
Density Level ◽  
Thousand Grain Weight ◽  
Original Algorithm ◽  
Different Types ◽  
Different Shapes ◽  
Density Map ◽  
Important Basis ◽  
Adhesion Condition

The thousand grain weight is an index of size, fullness and quality in crop seed detection and is an important basis for field yield prediction. To detect the thousand grain weight of rice requires the accurate counting of rice. We collected a total of 5670 images of three different types of rice seeds with different qualities to construct a model. Considering the different shapes of different types of rice, this study used an adaptive Gaussian kernel to convolve with the rice coordinate function to obtain a more accurate density map, which was used as an important basis for determining the results of subsequent experiments. A Multi-Column Convolutional Neural Network was used to extract the features of different sizes of rice, and the features were fused by the fusion network to learn the mapping relationship from the original map features to the density map features. An advanced prior step was added to the original algorithm to estimate the density level of the image, which weakened the effect of the rice adhesion condition on the counting results. Extensive comparison experiments show that the proposed method is more accurate than the original MCNN algorithm.

Experimental Examination of the Impact of Tool Radius on Specific Energy in Microcutting of Granite

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
Miloš Pjević ◽  
Ljubodrag Tanović ◽  
Goran Mladenović ◽  
Biljana Marković
Keyword(s):  
Cutting Force ◽  
Penetration Depth ◽  
Specific Energy ◽  
Brittle Materials ◽  
Experimental Examination ◽  
Workpiece Surface ◽  
Different Shapes ◽  
Tip Radius ◽  
The Impact ◽  
Force Intensity

The paper presents experimental results of microcutting brittle materials (granite). The analysis was conceived on the observed interaction between the workpiece and two tools of different shapes. Experiment was based on scratching the workpiece surface with diamond tools. Applied tools had tip radius R0.2 and R0.15 mm. The experiment determined the changes in the value of perpendicular and tangential components of the cutting force based on the geometric properties of tools, as well as the changes of the specific energy of microcutting granite (Jošanica and Bukovik types). The experiment has shown that reduction of tool radius causes reduction of the cutting force intensity and specific cutting energy. Because of its physical/mechanical properties, more energy is required for micromachining granite “Jošanica” than “Bukovik.” Based on the topography of the surface, the value of critical tool penetration depth was established, after which the brittle fracture is no longer present. For granite “Jošanica” values of critical penetration depth are 6 and 5 μm when micromachining with tools R0.2 and R0.15 mm, while for Bukovik those values are 6.5 and 5.5 μm. The paper should form the basis for understanding the phenomena which occur during microcutting brittle materials.

scholarly journals Rationalizing the impact of aging on fiber–matrix interface and stability of cement-based composites submitted to carbonation at early ages

2016 ◽  
Vol 51 (17) ◽  
pp. 7929-7943 ◽  
Author(s):  
G. H. D. Tonoli ◽  
V. D. Pizzol ◽  
G. Urrea ◽  
S. F. Santos ◽  
L. M. Mendes ◽  
...  
Keyword(s):  
Matrix Interface ◽  
Fiber Matrix Interface ◽  
Fiber Matrix ◽  
The Impact

An Introduction to the Impact Behaviour of Polymer Composites Using Simplified Beam Models

1998 ◽  
Vol 26 (2) ◽  
pp. 89-110 ◽  
Author(s):  
R. A. W. Mines
Keyword(s):  
Composite Materials ◽  
Undergraduate Students ◽  
Progressive Collapse ◽  
Structural Response ◽  
Sandwich Beams ◽  
Three Point Bending ◽  
The Past ◽  
Structural Case ◽  
The University ◽  
The Impact

The paper describes a final-year undergraduate course that has been taught at the University of Liverpool for the past three years. The main aims of the course are to introduce the student to the design of structures using multi-component (composite) materials and to the performance of such structures under impact loading. Given the complexity of generalized composite behaviour and of structural crashworthiness, a simple structural case is considered, namely, a beam subject to three-point bending. A feature of the course is that not only is linear structural response considered but also non-linear (progressive) structural collapse is covered. The course is split into four parts, namely: (i) analysis of composite laminae, (ii) analysis of laminated beams, (iii) local and global effects in sandwich beams, and (iv) post-failure and progressive collapse of sandwich beams. Static and impact loadings are considered. Comments are made on how the theories are simplified and communicated to the undergraduate students.

Sign in / Sign up

Export Citation Format

Share Document