scholarly journals Some Thermomagnetic and Mechanical Properties of Amorphous Fe75Zr4Ti3Cu1B17 Ribbons

Materials ◽  
2022 ◽  
Vol 15 (1) ◽  
pp. 368
Author(s):  
Mariusz Hasiak ◽  
Jan Świerczek
Keyword(s):  
Single Phase ◽  
Entropy Change ◽  
X Ray Diffraction ◽  
X Ray ◽  
Field Induction ◽  
Average Value ◽  
A Value ◽  
Amorphous Ferromagnet ◽  
Instrumental Hardness ◽  
Magnetizing Field

The microstructure, revealed by X-ray diffraction and transmission Mössbauer spectroscopy, magnetization versus temperature, external magnetizing field induction and mechanical hardness of the as-quenched Fe75Zr4Ti3Cu1B17 amorphous alloy with two refractory metals (Zr, Ti) have been measured. The X-ray diffraction is consistent with the Mössbauer spectra and is characteristic of a single-phase amorphous ferromagnet. The Curie point of the alloy is about 455 K, and the peak value of the isothermal magnetic entropy change, derived from the magnetization versus external magnetizing field induction curves, equals 1.7 J·kg−1·K−1. The refrigerant capacity of this alloy exhibits the linear dependence on the maximum magnetizing induction (Bm) and reaches a value of 110 J·kg−1 at Bm = 2 T. The average value of the instrumental hardness (HVIT) is about 14.5 GPa and is superior to other crystalline Fe-based metallic materials measured under the same conditions. HVIT does not change drastically, and the only statistically acceptable changes are visibly proving the single-phase character of the material.

MAGNETOCALORIC EFFECT IN THE INTERMETALLIC COMPOUND Gd3Ni8Al

2012 ◽  
Vol 26 (25) ◽  
pp. 1250167 ◽  
Author(s):  
M. X. WANG ◽  
H. FU ◽  
Q. ZHENG ◽  
J. TANG
Keyword(s):  
Intermetallic Compound ◽  
Magnetocaloric Effect ◽  
Single Phase ◽  
Magnetic Entropy Change ◽  
Magnetic Measurements ◽  
Entropy Change ◽  
Magnetic Entropy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Refrigerant Capacity

The magnetic properties and magnetocaloric effect of the polycrystalline Gd 3 Ni 8 Al intermetallic compound are studied in this paper. Powder X-ray diffraction shows that the alloy is CeNi 3-type single-phase structure. The magnetic measurements indicate that the compound is ferromagnetic and undergoes a second-order phase transition at 62 K. The maximum of magnetic entropy change reaches 11 J/kg K for the field change from 0 to 50 kOe and the refrigerant capacity of the titled compound is found to be 4.8×102 J/kg.

Structural and Electronic Properties of (CdTe)1−x(In2Te3)x Films Grown by Close-spaced vapor Transport Combined with Free Evaporation

2000 ◽  
Vol 15 (8) ◽  
pp. 1811-1815 ◽  
Author(s):  
M. Zapata-Torres ◽  
Y. P. Mascarenhas ◽  
M. A. Santana-Aranda ◽  
J. Luyo-Alvarado ◽  
M. Melé-Lirandez ◽  
...  
Keyword(s):  
Band Gap ◽  
Electronic Properties ◽  
Single Phase ◽  
Vapor Transport ◽  
X Ray Diffraction ◽  
X Ray ◽  
A Value ◽  
Structural And Electronic Properties ◽  
Direct Band ◽  
Transmission Measurements

The structural and electronic properties of (CdTe)1−x(In2Te3)x thin films as a function of substrate temperature were studied using x-ray diffraction, energy dispersive x-ray analysis, and Raman, transmission, and modulated transmission spectroscopies. The films were grown by the close-spaced vapor transport technique combined with free evaporation; CdTe and In2Te3 were used as sources. From x-ray diffraction the presence of mixed phases and differences in composition were detected, and good correlation with Raman spectroscopy was found. Transmission spectroscopy suggested the possibility of a modulation of the band gap of the alloy from a value as low as 0.5 eV up to 1.5 eV. Single-phase films presented a direct band gap of around 1.15 eV, as obtained from modulated transmission measurements.

Raman And Fluorescence Spectra Observed in Laser Microprobe Measurements of Several Compositions in the Ln-Ba-Cu-O System

1990 ◽  
Vol 48 (2) ◽  
pp. 278-279
Author(s):  
Edgar S. Etz ◽  
Thomas D. Schroeder ◽  
Winnie Wong-Ng
Keyword(s):  
Fluorescence Spectra ◽  
Single Phase ◽  
X Ray Diffraction ◽  
Ceramic Powders ◽  
Conventional Solid State Reaction ◽  
X Ray ◽  
Raman Microprobe ◽  
Methods Of Synthesis ◽  
Compositional Homogeneity ◽  
Processing Techniques

We are investigating by Raman microprobe measurements the superconducting and related phases in the LnBa2Cu3O7-x (for x=0 to 1) system where yttrium has been replaced by several of the lanthanide (Ln = Nd,Sm,Eu,Ho,Er) elements. The aim is to relate the observed optical spectra (Raman and fluorescence) to the compositional and structural properties of these solids as part of comprehensive materials characterization. The results are correlated with the methods of synthesis, the processing techniques of these materials, and their superconducting properties. Of relevance is the substitutional chemistry of these isostructural systems, the differences in the spectra, and their microanalytical usefulness for the detection of impurity phases, and the assessment of compositional homogeneity. The Raman spectra of most of these compounds are well understood from accounts in the literature.The materials examined here are mostly ceramic powders prepared by conventional solid state reaction techniques. The bulk samples are of nominally single-phase composition as determined by x-ray diffraction.

Observation of pseudo 10-fold symmetry in the ordered iron-zinc delta phase

1992 ◽  
Vol 50 (1) ◽  
pp. 36-37
Author(s):  
L. A. Giannuzzi ◽  
A. S. Ramani ◽  
P. R. Howell ◽  
H. W. Pickering ◽  
W. R. Bitler
Keyword(s):  
Single Phase ◽  
X Ray Diffraction ◽  
Rich Region ◽  
Average Cell ◽  
X Ray ◽  
Delta Phase ◽  
Cell Dimensions ◽  
Δ Phase ◽  
Morphological Differences ◽  
Concentration Discontinuity

The δ phase is a Zn-rich intermetallic, having a composition range of ∼ 86.5 - 92.0 atomic percent Zn, and is stable up to 665°C. The stoichiometry of the δ phase has been reported as FeZn7 and FeZn10 The deviation in stoichiometry can be attributed to variations in alloy composition used by each investigator. The structure of the δ phase, as determined by powder x-ray diffraction, is hexagonal (P63mc or P63/mmc) with cell dimensions a = 1.28 nm, c = 5.76 nm, and 555±8 atoms per unit cell. Later work suggested that the layer produced by hot-dip galvanizing should be considered as two distinct phases which are characterized by their morphological differences, namely: the iron-rich region with a compact appearance (δk) and the zinc-rich region with a columnar or palisade microstructure (δp). The sub-division of the δ phase was also based on differences in diffusion behavior, and a concentration discontinuity across the δp/δk boundary. However, work utilizing Weisenberg photographs on δ single crystals reported that the variation in lattice parameters with composition was small and hence, structurally, the δk phase and the δp phase were the same and should be thought of as a single phase, δ. Bastin et al. determined the average cell dimensions to be a = 1.28 nm and c = 5.71 nm, and suggested that perhaps some kind of ordering process, which would not be observed by x-ray diffraction, may be responsible for the morphological differences within the δ phase.

scholarly journals Preparation of high-entropy carbides by different sintering techniques

2021 ◽  
Vol 56 (19) ◽  
pp. 11237-11247 ◽  
Author(s):  
Johannes Pötschke ◽  
Manisha Dahal ◽  
Mathias Herrmann ◽  
Anne Vornberger ◽  
Björn Matthey ◽  
...  
Keyword(s):  
Grain Size ◽  
Single Phase ◽  
X Ray Diffraction ◽  
Vacuum Sintering ◽  
X Ray ◽  
High Entropy ◽  
Mean Grain Size ◽  
The Mean ◽  
Gas Pressure Sintering ◽  
Hardness Values

AbstractDense (Hf, Ta, Nb, Ti, V)C- and (Ta, Nb, Ti, V, W)C-based high-entropy carbides (HEC) were produced by three different sintering techniques: gas pressure sintering/sinter–HIP at 1900 °C and 100 bar Ar, vacuum sintering at 2250 °C and 0.001 bar as well as SPS/FAST at 2000 °C and 60 MPa pressure. The relative density varied from 97.9 to 100%, with SPS producing 100% dense samples with both compositions. Grain size measurements showed that the substitution of Hf with W leads to an increase in the mean grain size of 5–10 times the size of the (Hf, Ta, Nb, Ti, V,)C samples. Vacuum-sintered samples showed uniform grain size distribution regardless of composition. EDS mapping revealed the formation of a solid solution with no intermetallic phases or element clustering. X-ray diffraction analysis showed the structure of mostly single-phase cubic high-entropy carbides. Hardness measurements revealed that (Hf, Ta, Nb, Ti, V)C samples possess higher hardness values than (Ta, Nb, Ti, V, W)C samples.

scholarly journals Influence of Li2CO3 addition on electrical and magnetic properties of Ni0.6Mg0.4Fe2O4

2020 ◽  
Vol 10 (03) ◽  
pp. 2050003
Author(s):  
M. R. Hassan ◽  
M. T. Islam ◽  
M. N. I. Khan
Keyword(s):  
Magnetic Properties ◽  
Single Phase ◽  
Low Frequency ◽  
Solid State Reaction Method ◽  
Charge Carriers ◽  
X Ray Diffraction ◽  
X Ray ◽  
Electrical And Magnetic Properties ◽  
Frequency Regime ◽  
Xrd Patterns

In this research, influence of adding Li2CO3 (at 0%, 2%, 4%, 6%) on electrical and magnetic properties of [Formula: see text][Formula: see text]Fe2O4 (with 60% Ni and 40% Mg) ferrite has been studied. The samples are prepared by solid state reaction method and sintered at 1300∘C for 6[Formula: see text]h. X-ray diffraction (XRD) patterns show the samples belong to single-phase cubic structure without any impurity phase. The magnetic properties (saturation magnetization and coercivity) of the samples have been investigated by VSM and found that the higher concentration of Li2CO3 reduces the hysteresis loss. DC resistivity increases with Li2CO3 contents whereas it decreases initially and then becomes constant at lower value with temperature which indicates that the studied samples are semiconductor. The dielectric dispersion occurs at a low-frequency regime and the loss peaks are formed in a higher frequency regime, which are due to the presence of resonance between applied frequency and hopping frequency of charge carriers. Notably, the loss peaks are shifted to the lower frequency with Li2CO3 additions.

Impedance Spectroscopy Study of LiTaO3 Powder Synthesized via Sol-Gel Method

2012 ◽  
Vol 545 ◽  
pp. 275-278 ◽  
Author(s):  
Lili Widarti Zainuddin ◽  
Norlida Kamarulzaman
Keyword(s):  
Room Temperature ◽  
Single Phase ◽  
Sol Gel ◽  
Rhombohedral Structure ◽  
Spectroscopy Study ◽  
X Ray Diffraction ◽  
Gel Method ◽  
X Ray ◽  
Sol Gel Method ◽  
Impedance Spectroscopy Study

A ceramics sample of LiTaO3 was prepared using a sol-gel method. The sample is annealed at 750 °C for 48 hours. X-ray diffraction analysis indicate the formation of single phase, rhombohedral structure. An ac impedance study was used to analyse the conductivity of LiTaO3 at room temperature and at various temperatures.

Colossal Magnetoresistance in Thick La0.7Ca0.3MnO3 Films

1995 ◽  
Vol 384 ◽  
Author(s):  
Randolph E. Treece ◽  
P. Dorsey ◽  
M. Rubinstein ◽  
J. M. Byers ◽  
J. S. Horwitz ◽  
...  
Keyword(s):  
Colossal Magnetoresistance ◽  
Single Phase ◽  
Laser Deposition ◽  
Orthorhombic Structure ◽  
X Ray Diffraction ◽  
Post Deposition Annealing ◽  
X Ray ◽  
Mr Effect ◽  
Deposited Films ◽  
Post Deposition

ABSTRACTThick films (0.6 and 2.0 μm) of the colossal magnetoresistance (CMR) material, La0.7Ca0.3MnO3 (LCMO), have been grown by pulsed laser deposition (PLD). The films were grown from single-phase LCMO targets in 100 mTorr 02 pressures and the material deposited on (100) LaAlO3 substrates at deposition temperatures of 800°C. The deposited films were characterized by X-ray diffraction (XRD), magnetic field-dependent resistivity, and Rutherford backscattering spectroscopy (RBS). The LCMO films were shown by XRD to adopt an orthorhombic structure. Brief post-deposition annealing led to ~50,000% and ~12,000% MR effect in the 0.6 μm and 2.0 μm films, respectively.

INVESTIGATIONS ON Sm- AND Nb-SUBSTITUTED PZT CERAMICS

2006 ◽  
Vol 20 (29) ◽  
pp. 1879-1882 ◽  
Author(s):  
CHANDRA PRAKASH ◽  
J. K. JUNEJA
Keyword(s):  
Dielectric Constant ◽  
Single Phase ◽  
Xrd Analysis ◽  
Chemical Formula ◽  
X Ray Diffraction ◽  
Pzt Ceramics ◽  
Ceramic Method ◽  
X Ray ◽  
Niobium Doping ◽  
Constant Versus

In the present paper, we report the effect of Samarium substitution and Niobium doping on the properties of a PZT(52:48). The properties studied are: structural, dielectric and ferroelectric. The samples with chemical formula Pb 0.99 Sm 0.01 Zr 0.52 Ti 0.48 O 3 were prepared by solid-state dry ceramic method. Small amount (0.5 wt%) of Nb 2 O 5 was also added. X-ray diffraction (XRD) analysis showed formation of a single phase with tetragonal structure. Dielectric properties were studied as a function of temperature and frequency. Transition temperature, Tc, was determined from dielectric constant versus temperature plot. The material shows well-defined ferroelectric (PE) hysteresis loop.

Sign in / Sign up

Export Citation Format

Share Document