scholarly journals Application of Waterborne Acrylic and Solvent-Borne Polyester Coatings on Plasma-Treated Fir (Abies alba M.) Wood

Materials ◽  
2022 ◽  
Vol 15 (1) ◽  
pp. 370
Author(s):  
Hadi Gholamiyan ◽  
Behnam Gholampoor ◽  
Reza Hosseinpourpia
Keyword(s):  
Plasma Treatment ◽  
Treated Wood ◽  
Abies Alba ◽  
Untreated Wood ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Accelerated Weathering ◽  
Water Contact ◽  
Before And After ◽  
Carbon Dioxide Co2

This research investigates the effect of plasma treatment with air, nitrogen (N2), and carbon dioxide (CO2) gases on the performance of waterborne (acrylic) and solvent-borne (polyester) coated fir (Abies alba M.) wood samples. The properties of the plasma-coated samples were analyzed before and after exposure to accelerated weathering and compared with those of untreated and solely treated ones. According to pull-off testing, the coating adhesion of the wood samples was considerably improved by plasma treatment, and obvious differences were observed between different plasma gases. The effect was more pronounced after the weathering test. Similar results were obtained for the abrasion resistance of the samples. The water contact angle measurement illustrated more hydrophilic character in the solely plasma-treated wood in comparison with the untreated wood. The application of coatings, however, strongly improved its hydrophobic character. The performances of waterborne and solvent-borne coatings on plasma-treated wood were comparable, although slightly better values were obtained by the waterborne system. Our results exhibit the positive effect of plasma treatment on coating performances and the increased weather resistance of the waterborne and solvent-borne coating systems on plasma-treated wood.

Wettability measurements on two sandstones: an experimental investigation before and after CO2 flooding

2020 ◽  
Vol 60 (1) ◽  
pp. 117
Author(s):  
Cut Aja Fauziah ◽  
Emad A. Al-Khdheeawi ◽  
Ahmed Barifcani ◽  
Stefan Iglauer
Keyword(s):  
Contact Angle ◽  
Co2 Storage ◽  
Contact Angle Measurement ◽  
Contact Angles ◽  
Angle Measurement ◽  
Co2 Injection ◽  
Co2 Flooding ◽  
Berea Sandstone ◽  
Before And After ◽  
Carbon Dioxide Co2

Wettability of rock–fluid systems is an important for controlling the carbon dioxide (CO2) movement and the capacities of CO2 geological trapping mechanisms. Although contact angle measurement is considered a potentially scalable parameter for evaluation of the wettability characteristics, there are still large uncertainties associated with the contact angle measurement for CO2–brine–rock systems. Thus, this study experimentally examined the wettability, before and after flooding, of two different samples of sandstone: Berea and Bandera grey sandstones. For both samples, several sets of flooding of brine (5 wt % NaCl + 1 wt % KCl in deionised water), CO2-saturated (live) brine and supercritical CO2 were performed. The contact angle measurements were conducted for the CO2–sandstone system at two different reservoir pressures (10 and 15 MPa) and at a reservoir temperature of 323 K. The results showed that both the advancing and receding contact angles of the sandstone samples after flooding were higher than that measured before flooding (i.e. after CO2 injection the sandstones became more CO2-wet). Moreover, the Bandera grey samples had higher contact angles than Berea sandstone. Thus, we conclude that CO2 flooding altered the sandstone wettability to be more CO2-wet, and Berea sandstone had a higher CO2 storage capacity than Bandera grey sandstone.

Dual Functionality of TPU Nonwoven Prepared by Argon Plasma Treatment: A Method Forming Asymmetric Surface

2017 ◽  
Vol 381 ◽  
pp. 3-7
Author(s):  
Ko Shao Chen ◽  
Shao Hsuan Tsao ◽  
Rui Wen Sung ◽  
Ying Chen Ye ◽  
Bo Han Zeng ◽  
...  
Keyword(s):  
Plasma Treatment ◽  
Ion Beam ◽  
Argon Plasma ◽  
Hydrophobic Surface ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Water Contact ◽  
Lower Electrode ◽  
Atomic Force ◽  
High Elasticity

Thermoplastic urethane (TPU) nonwoven is characterized by high elasticity, tensile strength, large elongation and structural stability and widely used in biomaterial. However, the hydrophobic nature of TPU nonwoven restricts its application. To improve surface hydrophilicity and hydrophobicity, the surface modification of materials is carried out by plasma treatment or ion-beam irradiation. According to the wettability treatment experiences that substrate usually using two processing or more to get one side hydrophilic and another side hydrophobic. In this study, use of cold plasma treatment in enhancing surface wettability of TPU nonwoven was studied. The surface properties of plasma treated films are characterized by Atomic Force Microscope (AFM), water contact angle measurement, and scanning electron microscopy (SEM). This study has demonstrated that Argon plasma treatment produces hydrophobic or hydrophilic surface on the TPU nonwoven. The method is performed by first placing a hydrophobic material on one side of substrate and bring this side to face the lower electrode. By controlling the RF power of the reactor, hydrophilic or hydrophobic surface can be prepared on the other side. This technique can be applied to wound dressing.

Fabrication of superhydrophobic cotton fabrics through wrapping silica with plasma-induced grafting polymerization

2017 ◽  
Vol 89 (3) ◽  
pp. 401-410 ◽  
Author(s):  
Yongqiang Li ◽  
Chao Zou ◽  
Jianzhong Shao ◽  
Ya’nan Li
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Cotton Fabric ◽  
Photoelectron Spectroscopy ◽  
Contact Angle Measurement ◽  
Cotton Fabrics ◽  
Angle Measurement ◽  
Water Contact ◽  
Washing Durability ◽  
Before And After

Cotton fabric is commonly used in daily life, but it is easily wetted and contaminated by liquid. Herein, we present a simple and environmentally friendly plasma technology for hydrophobic modification of cotton fabric. In order to endow superhydrophobicity to cotton fabric, helium plasma inducing graft polymerization of 1,3,5,7-tetravinyl-1,3,5,7-tetramethylcyclotetrasiloxane (D4Vi) was utilized to wrap SiO2 particles on cotton fabrics. Cotton fabrics were successively dipped in silica sol and D4Vi, then treated by plasma. Cotton fabrics before and after modification were characterized by using field emission scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and water contact angle measurement. The experimental results showed that the cotton-SiO2-D4Vi consisted of nanoscale SiO2 protrusions and low-surface-energy film polymerized by D4Vi. In addition, the one wrapped SiO2 of 161 nm presented excellent hydrophobicity, washing durability, and repellency toward different types of liquids with a water contact angle of 152°.

Metallization Process for Polydimethylsiloxane (PDMS) Rubber

2007 ◽  
Vol 1009 ◽  
Author(s):  
Stéphane Béfahy ◽  
Sami Yunus ◽  
Véronique Burguet ◽  
Jean-Sébastien Heine ◽  
Etienne Dague ◽  
...  
Keyword(s):  
Plasma Treatment ◽  
Photoelectron Spectroscopy ◽  
Soxhlet Extraction ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Oxygen Plasma Treatment ◽  
Water Contact ◽  
Electrical Failure ◽  
Static Water ◽  
Hydrophobic Recovery

AbstractA process to fabricate stretchable and adherent gold tracks on flat silicone rubber substrates is studied by X-ray photoelectron spectroscopy (XPS), static water contact angle measurement, atomic force microscopy (AFM) and scanning electron microscopy (SEM). The process involves several steps: curing flat silicone substrate; removing uncured oligomers by hexane Soxhlet extraction; pre-stretching the substrate; activating the strained silicone surface by an oxygen plasma treatment; coating the strained substrate with 5nm titanium and 80nm gold layers by e-beam evaporation; and finally releasing the sample. The plasma treatment creates a thin brittle silica-like layer that temporarily increases the substrate's surface energy. Indeed the plasma treatment is followed by a hydrophobic recovery. As a consequence, the delay between plasma treatment and metal deposition has to be reduced as much as possible. The silica-like layer can be nicely observed after release. Its thickness is estimated to be around 20nm to 50nm. The entire process allows us to obtain stretchable metallized samples that remain conductive even after an excessive deformation leading to electrical failure.

Effects of Surface Treatments of Polycaprolactone Scaffolds on their Properties

2013 ◽  
Vol 747 ◽  
pp. 178-181 ◽  
Author(s):  
Wasana Kosorn ◽  
Boonlom Thavornyutikarn ◽  
Wanida Janvikul
Keyword(s):  
Contact Angle ◽  
Plasma Treatment ◽  
Alkaline Hydrolysis ◽  
Photoelectron Spectroscopy ◽  
Atomic Ratio ◽  
Contact Angle Measurement ◽  
Contact Angles ◽  
Angle Measurement ◽  
Water Contact ◽  
Oh Groups

Polycaprolactone (PCL) was surface modified with alkaline hydrolysis by NaOH and/or low pressure oxygen (O2) plasma treatment. The hydrolysis was conducted in two different stages: one was performed prior to PCL scaffold fabrication by a high pressure supercritical CO2 technique; the other was carried out after the fabrication. The resulting hydrolyzed PCL scaffolds, with pore sizes in the range of 150-250 μm, were denoted as pre-HPCL and post-HPCL, respectively. Both non-hydrolyzed and hydrolyzed PCL scaffolds were subsequently subjected to the plasma treatment, to further enhance the hydrophilicity of the scaffolds. The surface morphology, wettability and chemical composition of all PCL scaffolds were analyzed by scanning electron microscopy (SEM), water contact angle measurement, and X-ray photoelectron spectroscopy (XPS), respectively. It was found that the surface of the scaffolds turned from fairly smooth to highly rough after the hydrolysis and plasma treatment, particularly when both treatments were in use. The post-hydrolysis induced more surface roughness, compared to the pre-hydrolysis. In addition, the water contact angles on the scaffolds enormously reduced after the treatments; plasma treatment, however, showed a more prominent effect than the alkaline hydrolysis. Although expressing a zero-degree contact angle, the plasma-treated pre-HPCL scaffold was wetted more readily than the plasma-treated post-HPCL. These were in good agreement with the XPS results; interestingly, the plasma-treated pre-HPCL scaffold exhibited the greatest O/C atomic ratio among the PCL scaffolds. This indicated its highest extent of PCL chain oxidation, a degradation of ester groups into-COOH and-OH groups.

scholarly journals Superhydrophobic functionalized cellulosic paper by copper hydroxide nanorods for oils purification

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Ahmed S. Belal ◽  
Jehan El Nady ◽  
Azza Shokry ◽  
Shaker Ebrahim ◽  
Moataz Soliman ◽  
...  
Keyword(s):  
Contact Angle ◽  
Filter Paper ◽  
Separation Efficiency ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Absorption Capacity ◽  
Morphological Properties ◽  
Copper Hydroxide ◽  
Immersion Method ◽  
Water Contact

AbstractOily water contamination has been sighted as one of the most global environmental pollution. Herein, copper hydroxide nanorods layer was constructed onto cellulosic filter paper surface cured with polydopamine, Ag nanoparticles, and Cu NPs through immersion method. This work has been aimed to produce a superhydrophobic and superoleophilic cellulosic filter paper. The structure, crystalline, and morphological properties of these modified cellulosic filter paper were investigated. Scanning electron microscope images confirmed that the modified surface was rougher compared with the pristine surface. The contact angle measurement confirmed the hydrophobic nature of these modified surfaces with a water contact angle of 169.7°. The absorption capacity was 8.2 g/g for diesel oil and the separation efficiency was higher than 99%. It was noted that the flux in the case of low viscosity solvent as n-hexane was 9663.5 Lm−2 h−1, while for the viscous oil as diesel was 1452.7 Lm−2 h−1.

Plasma Pre-Treatment of Polyethylene Terephthalate Substrate Influence on the Properties of ZnO Thin Film

2014 ◽  
Vol 895 ◽  
pp. 41-44
Author(s):  
Seiw Yen Tho ◽  
Kamarulazizi Ibrahim
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Polyethylene Terephthalate ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Zno Thin Films ◽  
Zno Thin Film ◽  
Water Contact ◽  
Pre Treatment ◽  
Pet Substrate

In this work, the influences of plasma pre-treatment on polyethylene terephthalate (PET) substrate to the properties of ZnO thin film have been carried out. ZnO thin films were successfully grown on PET substrate by spin coating method. In order to study the effects of plasma pre-treatment, a comparison of treated and untreated condition was employed. Water contact angle measurement had been carried out for PET wettability study prior to ZnO thin film coating. Morphology study of ZnO thin film was performed by scanning probe microscope (SPM). Besides, optical study of the ZnO thin film was done by using UV-vis spectrophotometer. All the measured results show that plasma pre-treatment of PET substrate plays an important role in enhancing the wettability of PET and optical properties of the ZnO thin films. In conclusion, pre-treatment of PET surface is essential to produce higher quality ZnO thin film on this particular substrate in which would pave the way for the integration of future devices.

Curing Time and Water Repellent Properties of Dammar-Titanium Dioxide Thin Film

2015 ◽  
Vol 1112 ◽  
pp. 359-362
Author(s):  
Aisyah Nor Hasnan ◽  
Azizah Hanom Ahmad
Keyword(s):  
Contact Angle ◽  
Titanium Dioxide ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Water Repellent ◽  
Coating System ◽  
Curing Time ◽  
Coating Surface ◽  
Natural Resin ◽  
Before And After

Dammar plant resin is a local natural resin that can be bled from Dipterocaupacea sp of tree. It can be found abundantly in Malaysia’s tropical forest especially in Sarawak. Dammar and Titanium Dioxide was mixed in a various wt% to produce Dammar-modified Titanium Dioxide coating system. The modified coating systems were then spin-coated onto Aluminium Q-panel as the substrate. Coated Q-panels were left to cure at room temperature. The curing time was evaluated using dust free stage. The addition of Titanium Dioxide into the coating system fastens the curing time taken for the coated Q-panel to be cure. It only took about 11-12 minutes to dry compared to the coating system before the addition of Titanium Dioxide where a quite long duration required, 32 minutes. Contact angle measurement was also carried out in order to determine the wettability of the coating system. The surface coated with dammar-modified titanium dioxide found to be hydrophobic where a quite large contact angle obtained for the sample with 3 wt% of Titanium Dioxide (PDT3). The water droplets actually rest on the coating surface without wetting the surface. Water absorption test was done to strengthen the contact angle results where coated substrate was soaked into distilled water for 24 hours and being weighed before and after soaking. The difference of before and after soaking weigh showed that the coating surface does not absorb that much water where only approximately 0.02% of water being absorbed by the coating system for 3 wt%. It proved that the coating systems applied are hydrophobic.

Preparation of TiO2–SiO2 Hybrid Nanosols Coated Flame-Retardant Polyester Fabric Possessing Dual Contradictory Characteristics of Superhydrophobicity and Self Cleaning Ability

2020 ◽  
Vol 20 (3) ◽  
pp. 1780-1789 ◽  
Author(s):  
Priyanka Katiyar ◽  
Shraddha Mishra ◽  
Anurag Srivastava ◽  
N. Eswara Prasad
Keyword(s):  
Electron Microscopy ◽  
Contact Angle ◽  
Flame Retardant ◽  
Protective Clothing ◽  
Sol Gel ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Water Contact ◽  
Vis Spectroscopy ◽  
Self Cleaning

TiO2, SiO2 and their hybrid nanocoatings are prepared on inherent flame retardant textile substrates from titanium(IV)iso-proproxide (TTIP) and tetraethoxysilane (TEOS) precursors using a sol–gel process followed by hydrothermal treatment. The coated samples are further functionalized by hexadecyltrimethoxysilane (HDTMS) to impart superhydrophobicity. Sample characterization of the nanosols, nanoparticles and coated samples are investigated using, X-ray diffractometer, transmission electron microscopy, scanning electron microscopy, UV-Vis spectroscopy, contact angle measurement. Stain degradation test under mild UV irradiation shows almost 54% degradation of coffee stain within 4 hours measured by Spectrophotometer. UV-Vis Absorption Spectroscopy demonstrates complete degradation of methyl orange colorant within 3 hours. Hybrid nanosol coated and HDTMS modified inherent flame retardant polyester surfaces show apparent water contact angle as ~145°, which is much closer to proximity of superhydrophobic surfaces. Thus, the novelty of present work is, by using sol–gel technique, a bi-functional textile surface has been developed which qualifies the very specific requirements of protective clothing like self-cleaning property (imparted by TiO2 nanoparticles) and superhydrophobicity (imparted by SiO2 nanoparticles and further surface modification by HDTMS), which are entirely contradictory in nature, in a single fabric itself. Thus developed textile surfaces also possess the other attributes of protective clothing like flame retardancy and air permeability.

scholarly journals High Loading Capacity and Wear Resistance of Graphene Oxide/Organic Molecule Assembled Multilayer Film

2021 ◽  
Vol 9 ◽  
Author(s):  
Li Chen ◽  
Gang Wu ◽  
Yin Huang ◽  
Changning Bai ◽  
Yuanlie Yu ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
Multilayer Films ◽  
Thickness Measurement ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Film Structure ◽  
Silicon Substrates ◽  
Water Contact ◽  
Macro Scale

Taking advantage of the strong charge interactions between negatively charged graphene oxide (GO) sheets and positively charged poly(diallyldimethylammonium chloride) (PDDA), self-assembled multilayer films of (GO/PDDA)n were created on hydroxylated silicon substrates by alternating electrostatic adsorption of GO and PDDA. The formation and structure of the films were analyzed by means of water contact angle measurement, thickness measurement, atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). Meanwhile, tribological behaviors in micro- and macro- scale were investigated by AFM and a ball-on-plate tribometer, respectively. The results showed that (GO/PDDA)n multilayer films exhibited excellent friction-reducing and anti-wear abilities in both micro- and macro-scale, which was ascribed to the special structure in (GO/PDDA)n multilayer films, namely, a well-stacked GO–GO layered structure and an elastic 3D crystal stack in whole. Such a film structure is suitable for design molecular lubricants for MEMS and other microdevices.

Sign in / Sign up

Export Citation Format

Share Document