scholarly journals The Pilot Study of the Influence of Free Ammonia on Membrane Fouling during the Partial Nitrosation of Pig Farm Anaerobic Digestion Liquid

Membranes ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 894
Author(s):  
Hanxiao Bian ◽  
Zhiping Zhu ◽  
Qianwen Sui ◽  
Shunli Wang
Keyword(s):  
Membrane Fouling ◽  
Ammonia Oxidation ◽  
Operation Mode ◽  
Critical Role ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Free Ammonia ◽  
Transmembrane Pressure ◽  
Start Up ◽  
Pilot Scale Reactor

The problem of membrane fouling is a key factor restricting the application of the membrane bioreactor (MBR) in the partial nitrosation (PN) and anaerobic ammonia oxidation (anammox) processes. In this study, the pilot-scale continuous flow MBR was used to start up the partial nitrosation process in order to investigate the change trend of mid-transmembrane pressure (TMP) in the process of start-up, which was further explored to clarify the membrane fouling mechanism in the pilot-scale reactor. The results showed that the MBR system was in a stable operating condition during the partial nitrosation operation and that the online automatic backwash operation mode is beneficial in alleviating membrane fouling and reducing the cost of membrane washing. Particular attention was paid to the influence trend of free ammonia (FA)on membrane fouling, and it was found that the increase in FA concentration plays the most critical role in membrane fouling. The increase in FA concentration led to an increase in the extracellular polymer (EPS), dissolved microorganism product (SMP) and soluble chemical oxygen demand (SCOD) concentration. FA was extremely significantly correlated with EPS and SCOD, and the FA concentration was approximately 20.7 mg/L. The SCODeff (effluent SCOD concentration) concentration was approximately 147 mg/L higher than the SCODinf (influent SCOD concentration) concentration. FA mainly affects membrane fouling by affecting the concentration of EPS and SCOD.

Treatment of winery wastewaters in a membrane submerged bioreactor

2007 ◽  
Vol 56 (2) ◽  
pp. 63-69 ◽  
Author(s):  
P. Artiga ◽  
M. Carballa ◽  
J.M. Garrido ◽  
R. Méndez
Keyword(s):  
Tap Water ◽  
Oxygen Demand ◽  
Biomass Concentration ◽  
Pilot Scale ◽  
White Wine ◽  
Hollow Fibre ◽  
Organic Loading Rate ◽  
Wine Production ◽  
Solids Concentration ◽  
Start Up

Wine production is seasonal, and thus the wastewater flow and its chemical oxygen demand (COD) concentrations greatly vary during the vintage and non-vintage periods, as well as being dependant on the winemaking technologies used, e.g. red, white or special wines production. Due to this seasonal high variability in terms of organic matter load, the use of membrane biological reactors (MBR) could be suitable for the treatment of such wastewaters. MBR offers several benefits, such as rapid start up, good effluent quality, low footprint area, absence of voluminous secondary settler and its operation is not affected by the settling properties of the sludge. A pilot scale hollow fibre MBR system of 220 L was fed by adequately diluting white wine with tap water, simulating wastewaters generated in wineries. The COD in the influent ranged between 1,000 and 4,000 mg/L. In less than 10 days after the start up, the system showed a good COD removal efficiency. The COD elimination percentage was always higher than 97% regardless of the organic loading rate (OLR) applied (0.5–2.2 kg COD/m3 d), with COD concentrations in the effluent ranging between 20 and 100 mg/L. Although the biomass concentration in the reactor increased from 0.5 to 8.6 g VSS/L, the suspended solids concentration in the effluent was negligible. Apparent biomass yield was estimated in 0.14 g VSS/g COD.

Performance and membrane fouling in a pilot scale SBR process coupled with membrane

2003 ◽  
Vol 47 (1) ◽  
pp. 139-144 ◽  
Author(s):  
H. Shin ◽  
S. Kang
Keyword(s):  
Membrane Fouling ◽  
Batch Reactor ◽  
Pilot Scale ◽  
Nitrifying Bacteria ◽  
Endogenous Respiration ◽  
Aeration Time ◽  
Membrane Flux ◽  
Start Up ◽  
Cell Test ◽  
Stirred Cell

The performance of the pilot-scale submerged membrane coupled with sequencing batch reactor (SM-SBR) for upgrading effluent quality was investigated in this study. The reactor was operated with 3-hour cycle with alternating anoxic and aerobic conditions to treat organics, nitrogen and phosphate. Despite various influent characteristics, COD removal was always higher than 95%. Sufficient nitrification was obtained within a few weeks after start-up and during the stable period, complete nitrification occurred despite short aeration time. Total nitrogen (TN) removal efficiency was reached up to 85%. Membrane flux was critical for TN removal so that the decrease of flux by membrane fouling led to increase of HRT, and it caused the endogenous respiration of microorganisms such as nitrifying bacteria. The stirred cell test revealed the significant role of the soluble fraction in membrane permeability and dissolved solids played a major role in the short-term fouling mechanism. The cake resistance by the soluble COD fraction of supernatant or soluble microbial products (SMP) was investigated as a major part of total resistance.

Environmental performance of an integrated fixed-film activated sludge (IFAS) reactor treating actual municipal wastewater during start-up phase

2015 ◽  
Vol 72 (10) ◽  
pp. 1840-1850 ◽  
Author(s):  
Nitin Kumar Singh ◽  
Absar Ahmad Kazmi ◽  
Markus Starkl
Keyword(s):  
Activated Sludge ◽  
Pathogenic Bacteria ◽  
Municipal Wastewater ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Lessons Learned ◽  
Present System ◽  
Salmonella Spp ◽  
Start Up ◽  
Fixed Film

The present study summarizes the start-up performance and lessons learned during the start-up and optimization of a pilot-scale plant employing integrated fixed film activated sludge (IFAS) process treating actual municipal wastewater. A comprehensive start-up was tailored and implemented to cater for all the challenges and problems associated with start-up. After attaining desired suspended biomass (2,000–3,000 mg/L) and sludge age (∼7 days), the average biological oxygen demand (BOD) and chemical oxygen demand (COD) removals were observed as 77.3 and 70.9%, respectively, at optimized conditions, i.e. hydraulic retention time (HRT), 6.9 h; return sludge rate, 160%. The influent concentrations of COD, BOD, total suspended solids, NH3-N, total nitrogen and total phosphorus were found to be in the range of 157–476 mg/L, 115–283 mg/L, 152–428 mg/L, 23.2–49.3 mg/L, 30.1–52 mg/L and 3.6–7.8 mg/L, respectively, and the minimum effluent concentrations were achieved as ∼49 mg/L, 23 mg/L, 35 mg/L, 2.2 mg/L, 3.4 mg/L and 2.8 mg/L, respectively, at optimum state. The present system was found effective in the removal of pathogenic bacteria (Escherichia coli, 79%; Salmonella spp., 97.5%; Shigella spp., 92.9%) as well as coliforms (total coliforms, 97.65%; faecal coliforms, 80.35%) without any disinfection unit. Moreover it was observed that the time required for the stabilization of the plant was approximately 3 weeks if other parameters (sludge age, HRT and dissolved oxygen) are set to optimized values.

Optimization of a mainstream nitritation-denitritation process and anammox polishing

2015 ◽  
Vol 72 (4) ◽  
pp. 632-642 ◽  
Author(s):  
Pusker Regmi ◽  
Becky Holgate ◽  
Dana Fredericks ◽  
Mark W. Miller ◽  
Bernhard Wett ◽  
...  
Keyword(s):  
Retention Time ◽  
Pilot Plant ◽  
Municipal Wastewater ◽  
Ammonia Oxidation ◽  
Inorganic Nitrogen ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
High Rate ◽  
Anammox Bacteria ◽  
Tin Removal

This paper deals with an almost 1-year long pilot study of a nitritation-denitritation process that was followed by anammox polishing. The pilot plant treated real municipal wastewater at ambient temperatures. The effluent of high-rate activated sludge process (hydraulic retention time, HRT = 30 min, solids retention time = 0.25 d) was fed to the pilot plant described in this paper, where a constant temperature of 23 °C was maintained. The nitritation-denitritation process was operated to promote nitrite oxidizing bacteria out-selection in an intermittently aerated reactor. The intermittent aeration pattern was controlled using a strategy based on effluent ammonia and nitrate + nitrite concentrations. The unique feature of this aeration control was that fixed dissolved oxygen set-point was used and the length of aerobic and anoxic durations were changed based on the effluent ammonia and nitrate + nitrite concentrations. The anaerobic ammonia oxidation (anammox) bacteria were adapted in mainstream conditions by allowing the growth on the moving bed bioreactor plastic media in a fully anoxic reactor. The total inorganic nitrogen (TIN) removal performance of the entire system was 75 ± 15% during the study at a modest influent chemical oxygen demand (COD)/NH4+-N ratio of 8.9 ± 1.8 within the HRT range of 3.1–9.4 h. Anammox polishing contributed 11% of overall TIN removal. Therefore, this pilot-scale study demonstrates that application of the proposed nitritation-denitritation system followed by anammox polishing is capable of relatively high nitrogen removal without supplemental carbon and alkalinity at a low HRT.

Performance of SIDMBR for Emulsified Oil Wastewater Treatment

2013 ◽  
Vol 448-453 ◽  
pp. 478-481
Author(s):  
Zhi Yong Han ◽  
Si Su ◽  
Yan Lu ◽  
Wang Bing Du
Keyword(s):  
Wastewater Treatment ◽  
Membrane Fouling ◽  
Extracellular Polymeric Substances ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Ammonia Nitrogen ◽  
Dynamic Membrane ◽  
Emulsified Oil ◽  
Membrane Flux ◽  
Oil Wastewater

The Sequencing Inclined Dynamic Membrane Biological Reactor (SIDMBR) was investigated on a pilot scale for 60 days of emulsified oil wastewater treatment at zero excess sludge discharge. Results indicate that at hydraulic retention time of 24 h, the average removals of chemical oxygen demand (COD), ammonia nitrogen and oil are 66.83, 64.2 and 70.8% in 1~60 days, respectively. The membrane flux, biofilm quantity, and extracellular polymeric substances (EPS) content begin to change after 20th, which indicate that membrane fouling has occurred.

scholarly journals The color removal and fate of organic pollutants in a pilot-scale MBR-NF combined process treating textile wastewater with high water recovery

2015 ◽  
Vol 73 (6) ◽  
pp. 1426-1433 ◽  
Author(s):  
Kun Li ◽  
Chao Jiang ◽  
Jianxing Wang ◽  
Yuansong Wei
Keyword(s):  
Membrane Fouling ◽  
Oxygen Demand ◽  
Textile Wastewater ◽  
High Water ◽  
Pilot Scale ◽  
Water Yield ◽  
Water Recovery ◽  
Treatment Efficiency ◽  
Textile Mill ◽  
Refractory Compounds

A combination of membrane bioreactor (MBR) and nanofiltration (NF) was tested at pilot-scale treating textile wastewater from the wastewater treatment station of a textile mill in Wuqing District of Tianjin (China). The MBR-NF process showed a much better treatment efficiency on the removal of the chemical oxygen demand, total organic carbon, color and turbidity in comparison with the conventional processes. The water recovery rate was enhanced to over 90% through the recycling of NF concentrate to the MBR, while the MBR-NF showed a stable permeate water quality that met with standards and could be directly discharged or further reused. The recycled NF concentrate caused an accumulation of refractory compounds in the MBR, which significantly influenced the treatment efficiency of the MBR. However, the sludge characteristics showed that the activated sludge activity was not obviously inhibited. The results of fluorescence spectra and molecular weight distribution indicated that those recalcitrant pollutants were mostly protein-like substances and a small amount of humic acid-like substances (650–6,000 Da), which contributed to membrane fouling of NF. Although the penetrated protein-like substances caused the residual color in NF permeate, the MBR-NF process was suitable for the advanced treatment and reclamation of textile wastewater under high water yield.

scholarly journals Pilot-scale study to investigate the impact of rotating belt filter upstream of a MBR for nitrogen removal

2019 ◽  
Vol 79 (3) ◽  
pp. 458-465
Author(s):  
V. A. Razafimanantsoa ◽  
D. Adyasari ◽  
A. K. Sahu ◽  
B. Rusten ◽  
T. Bilstad ◽  
...  
Keyword(s):  
Organic Matter ◽  
Municipal Wastewater ◽  
Biogas Production ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Primary Treatment ◽  
Treated Wastewater ◽  
Transmembrane Pressure ◽  
Fine Mesh ◽  
The Impact

Abstract The goal of this study was to investigate what kind of impact the removal of particulate organic matter with 33μm rotating belt filter (RBF) (as a primary treatment) will have on the membrane bioreactor (MBR) performance. Two small MBR pilot plants were operated in parallel, where one train treated 2mm screened municipal wastewater (Train A) and the other train treated wastewater that had passed through a RBF with a 33μm filter cloth (Train B). The RBF was operated without a filter mat on the belt. About one third of the organic matter was removed by the fine mesh filter. The assessment of the overall performance showed that the two pilot plants achieved approximately the same removal efficiencies with regard to total suspended solids (TSS), chemical oxygen demand (COD), total phosphorus and total nitrogen. It was also observed that the system with 33μm RBF as a primary treatment produced more sludge, which could be used for biogas production, and required about 30% less aeration downstream. Transmembrane pressure was significantly lower for the train receiving 33μm primary treated wastewater compared to the control receiving 2mm screened wastewater.

scholarly journals Microbiological and physicochemical evaluation of the effluent quality in a membrane bioreactor system to meet the legislative limits for wastewater reuse

2017 ◽  
Vol 76 (7) ◽  
pp. 1796-1804 ◽  
Author(s):  
Konstantinos Azis ◽  
Charalampos Vardalachakis ◽  
Spyridon Ntougias ◽  
Paraschos Melidis
Keyword(s):  
Membrane Bioreactor ◽  
Municipal Wastewater ◽  
Wastewater Reuse ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Transmembrane Pressure ◽  
Permeate Flux ◽  
Effluent Quality ◽  
Mediterranean Countries

The aim of this study was to assess the efficacy and effluent quality of a pilot-scale intermittently aerated and fed, externally submerged membrane bioreactor (MBRes) treating municipal wastewater. The effluent quality of the MBRes was evaluated regarding system ability to comply with the Greek legislative limits for restricted and unrestricted wastewater reuse. The average permeate flux was 13.9 L m−2 h−1, while the transmembrane pressure remained above the level of −110 mbar. Experimental data showed that biochemical oxygen demand, chemical oxygen demand, total nitrogen, PO43−- P and total suspended solids removal efficiencies were 97.8, 93.1, 89.6, 93.2 and 100%, respectively, whereas turbidity was reduced by 94.1%. Total coliforms and Escherichia coli were fully eliminated by ultrafiltration and disinfection methods, such as chlorination and ultraviolet radiation. In agreement with the Greek legislation (Joint Ministerial Decree 145116/11) and the guidelines recommended for the Mediterranean countries, the disinfected effluent of the MBRes system can be safely reused directly for urban purposes.

scholarly journals Fouling membrane in an anaerobic membrane bioreactor treating municipal wastewater

2017 ◽  
Vol 12 (2) ◽  
pp. 314-321 ◽  
Author(s):  
A. Cerón-Vivas ◽  
A. Noyola
Keyword(s):  
Membrane Fouling ◽  
Municipal Wastewater ◽  
Scale Up ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Cod Removal ◽  
Anaerobic Sludge ◽  
Nitrogen Gas ◽  
Gas Bubbling ◽  
Anaerobic Sludge Blanket

An anaerobic membrane reactor (AnMBR) treating municipal wastewater was evaluated. The experiments were performed using a pilot-scale up-flow anaerobic sludge blanket reactor with a submerged tubular ultrafiltration membrane at a hydraulic retention time of 8 hours. The system worked at an intermittent filtration mode (4 min on/1 min off) with and without nitrogen gas bubbling during the relaxation time (IF4NP and IF4P, respectively). The chemical oxygen demand (COD) removal achieved by the AnMBR was 68.6% and 87.9% for IF4P and IF4NP. Nitrogen bubbling also improved the filtration performance, as the elapsed time to reach 40 kPa for IF4NP and IF4P were 443 and 108 hours, respectively. Results show that intermittent filtration combined with nitrogen bubbling during the period of relaxation was an effective operation strategy in order to minimize membrane fouling and to increase COD removal.

scholarly journals Tannery Wastewater Recalcitrant Compounds Foster the Selection of Fungi in Non-Sterile Conditions: A Pilot Scale Long-Term Test

2021 ◽  
Vol 18 (12) ◽  
pp. 6348
Author(s):  
Francesco Spennati ◽  
Salvatore La China ◽  
Giovanna Siracusa ◽  
Simona Di Gregorio ◽  
Alessandra Bardi ◽  
...  
Keyword(s):  
Oxygen Demand ◽  
Packed Bed ◽  
Pilot Scale ◽  
Packed Bed Reactor ◽  
Tannery Wastewater ◽  
Start Up ◽  
Quebracho Tannin ◽  
Entire Experiment ◽  
Bacteria And Fungi

This study demonstrated that a microbial community dominated by fungi can be selected and maintained in the long-term under non-sterile conditions, in a pilot-scale packed-bed reactor fed with tannery wastewater. During the start-up phase, the reactor, filled with 0.6 m3 of polyurethane foam cubes, was inoculated with a pure culture of Aspergillus tubingensis and Quebracho tannin, a recalcitrant compound widely used by tannery industry, was used as sole carbon source in the feeding. During the start-up, fungi grew attached as biofilm in carriers that filled the packed-bed reactor. Subsequently, the reactor was tested for the removal of chemical oxygen demand (COD) from an exhaust tanning bath collected from tanneries. The entire experiment lasted 121 days and average removals of 29% and 23% of COD and dissolved organic carbon (DOC) from the tannins bath were achieved, respectively. The evolution of the microbial consortium (bacteria and fungi) was described through biomolecular analyses along the experiment and also developed as a function of the size of the support media.

Sign in / Sign up

Export Citation Format

Share Document