scholarly journals Effect of Ca Addition on Corrosion Behavior of Wrought AM60 Magnesium Alloy in Alkaline Solutions

Metals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1172
Author(s):  
Polina Metalnikov ◽  
Guy Ben-Hamu ◽  
Kwang Seon Shin ◽  
Amir Eliezer

Magnesium (Mg) alloys possess the lowest density among structural materials, and their application in the automotive and aircraft industries might enhance fuel efficiency. The mechanical properties can be improved by the addition of alloying elements. However, since Mg and its alloys are very susceptible to corrosion degradation, it is important to study the effect of these elements on the alloys’ corrosion behavior. In this study, 1 wt% of calcium (Ca) was added to wrought AM60 Mg alloy, and the electrochemical corrosion behavior of the alloys in alkaline solutions with and without Cl− ions was compared. The corrosion behavior was investigated by means of immersion tests, gravimetric measurements and potentiodynamic polarization (PDP); the characteristics of the oxide layer were studied by electrochemical impedance spectroscopy (EIS) and X-ray photoelectron spectroscopy (XPS). The addition of Ca resulted in precipitation of the ternary aluminum-rich (Mg-Al)2Ca phase. Scanning Kelvin probe force microscope (SKPFM) identified that this phase has a cathodic behavior relative to the α-Mg matrix; hence it can serve as additional sites for initiation of pitting corrosion. As a result, the corrosion resistance of wrought AM60 alloy with 1 wt% Ca addition deteriorated in a NaCl solution. However, in the absence of Cl− ions, alloying with Ca improves the corrosion resistance of wrought AM60 alloy due to the stabilization of the corrosion products layer. The effect of long-period immersion time on the corrosion behavior and alloy oxidation is discussed.

2018 ◽  
Vol 69 (1) ◽  
pp. 86-90 ◽  
Author(s):  
Ioana Arina Gherghescu ◽  
Daniela Ionita ◽  
Sorin Ciuca ◽  
Ruxandra Elena Dumitrescu

This paper presents some electrochemical impedance spectroscopy research results concerning the corrosion resistance of a shape memory Ni50Ti48Nb2 alloy. This one was previously studied by SEM and DSC [1,2] but some new research features had to be made clear in order to be able to explain its electrochemical corrosion behavior. The chemical composition Ni50Ti48Nb2 was chosen in order to obtain a shape memory alloy having a wider hysteresis than equiatomic NiTi, for the purpose of achieving a better thermomechanical stability. Cryogenic applications are aimed. After processing the cast ingot, two samples, S1 and S2, were further annealed at 800�C/12 h and, respectively, at 900�C/12h. Scanning electron micrographs together with the chemical elements mapping results were obtained. They were related to the previous results concerning the informations on the structure of the different phases found in this NiTiNb alloy: austenite, martensite and secondary phases, as well as some primary compounds [1,2]. Considering the size and shape of the complex precipitate particles of NiTiNb in the two differently heat treated samples, these were found responsible for some changes in the transformation temperatures [3] but the electrochemical corrosion behavior of the alloy seems to be influenced to a lesser extent by the heat treatments. Both samples exhibit good values of corrosion resistance, however S2 shows better values than S1. Thus lower transformation temperatures and a slightly better corrosion resistance make the Ni50Ti48Nb2 alloy annealed at 900�C/12h subsequently submitted to thermal cycling to be the right choice for producing couplings in the cryogenic industry.


Coatings ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 986
Author(s):  
Jozef Minda ◽  
Stanislava Fintová ◽  
Branislav Hadzima ◽  
Pavel Doležal ◽  
Michaela Hasoňová ◽  
...  

Pure Mg samples were prepared by powder metallurgy using the cold and hot compacting methods. Cold compacted pure Mg (500 MPa/RT) was characterized by 5% porosity and the mechanical bonding of powder particles. Hot compacted samples (100 MPa/400 °C and 500 MPa/400 °C) exhibited porosity below 0.5%, and diffusion bonding combined with mechanical bonding played a role in material compaction. The prepared pure Mg samples and wrought pure Mg were subjected to corrosion tests using electrochemical impedance spectroscopy. Similar material corrosion behavior was observed for the samples compacted at 500 MPa/RT and 100 MPa/400 °C; however, hot compacted samples processed at 500 MPa/400 °C exhibited longer corrosion resistance in 0.9% NaCl solution. The difference in corrosion behavior was mainly related to the different binding mechanisms of the powder particles. Cold compacted samples were characterized by a more pronounced corrosion attack and the creation of a porous layer of corrosion products. Hot compacted samples prepared at 500 MPa/400 °C were characterized by uniform corrosion and the absence of a layer of corrosion products on the specimen surface. Powder-based cold compacted samples exhibited lower corrosion resistance compared to the wrought pure Mg, while the corrosion behavior of the hot compacted samples prepared at 500 MPa/400 °C was similar to that of wrought material.


CORROSION ◽  
10.5006/3490 ◽  
2021 ◽  
Author(s):  
Caiyun Bai ◽  
Peifeng Li ◽  
Tieqiang Gang ◽  
Jian Li ◽  
Min Wei ◽  
...  

Ti-6Al-4V alloys are typically used for biomedical implants, aerospace components and offshore equipment, where corrosion resistance is critical. In the present paper, the electrochemical corrosion behaviors of Ti-6Al-4V alloys made by different traditional processing and 3D printing technologies in seawater, 3.5 wt.% NaCl, 3.5 wt.% HCl, 5 wt.% HCl and 10 wt.% HCl solutions were studied through polarization curve and electrochemical impedance spectra (EIS) analyses. The influences of microstructure and printing parameters on the corrosion behaviors of Ti-6Al-4V alloys were analyzed. In addition, the corrosion current density, film resistance and charge transfer resistance of traditionally processed Ti-6Al-4V and 3D printed Ti-6Al-4V in the five solutions were compared. The results show that Ti-6Al-4V possesses a better corrosion resistance in seawater than in 3.5 wt.% NaCl, and that the corrosion rate increases with the HCl concentration. Besides, 3D printed Ti-6Al-4V shows a higher corrosion rate in comparison with traditionally processed Ti-6Al-4V because pores are effortless to enrich Cl-. Finally, the ratio of laser power to its scanning speed and the phase constituent composition of the alloy have slight influences on its electrochemical corrosion behavior. It is suggested that for the 3D printed alloy, the deterioration of mechanical properties induced by corrosion damage during servicing should be assessed and considered.


2020 ◽  
Vol 10 (13) ◽  
pp. 4568
Author(s):  
Hany S. Abdo ◽  
Asiful H. Seikh ◽  
Jabair A. Mohammed ◽  
Monis Luqman ◽  
Sameh A. Ragab ◽  
...  

Reinforced steel bars (rebar) are extensively used in construction, and the main challenge is in minimizing corrosion due to oxide or passive layer breakdown. In contrast, dual-phase (DP) steel has good corrosion resistance. This study investigated the effect of Cl− ions on the electrochemical corrosion behavior of DP rebar and conventional rebar. Corrosion behavior studies and electrochemical measurements were conducted on DP rebar and conventional rebar in simulated concrete pore solution with different concentrations of Cl− ions. Microstructure analysis, surface morphology analysis, and corroded surface characterization were performed using optical microscopy, field emission scanning electron microscopy, and Raman spectroscopy, respectively. Potentiodynamic polarization and electrochemical impedance spectroscopy measurements revealed that DP rebar has good passivity, leading to better corrosion resistance and greater strength compared to ordinary rebar. In addition, DP rebar showed better passivity behavior compared to conventional rebar in alkaline solution. Therefore, the presence of a dual phase (ferrite and martensite) in reinforced concrete structured steel induces good corrosion resistance.


2014 ◽  
Vol 1033-1034 ◽  
pp. 1258-1262 ◽  
Author(s):  
Xia Wen Le ◽  
Dan Ji ◽  
Qing Dong Zhong ◽  
Qiong Yu Zhou ◽  
Tong Mo ◽  
...  

Different compositions to prepare the Fe3Al intermetallic were analyzed through the microstructure and electrochemical corrosion behavior. The structure and microstructure were analyzed by X-ray and scanning electron microstructure (SEM). The corrosion resistance of samples was evaluated by potentiodynamic polarization (Tafel) and electrochemical impedance spectroscopy (EIS). Results show that the alloy with a composition of pure aluminum with pure iron shows a higher corrosion resistance.


2021 ◽  
Vol 904 ◽  
pp. 519-524
Author(s):  
Gui Yun Zhang ◽  
Yong Wang ◽  
Tian Wei Zhang ◽  
Chen Yu Zhao

Sea water resources are extensive and can be used to extinguish fires, but their corrosiveness is a major problem. Using the method of electrochemical workstation, the electrochemical corrosion behavior of aluminum sheet in artificial sea water solution and silica-coated artificial seawater was studied; by analyzing the surface morphology, polarization curve and electrochemical impedance spectroscopy, the electrochemical corrosion behavior of aluminum sheets under different immersion times and different immersion media is obtained. The conclusion is that the coating of nanosilica powder has a certain corrosion protection effect on artificial seawater.


2014 ◽  
Vol 906 ◽  
pp. 275-282
Author(s):  
Zhu Huan Yu ◽  
Jun Feng Qiang ◽  
Hui Lu Li

The effect of graphite shapes on the electrochemical corrosion behavior of cast iron was studied by means of weight loss tests, electrochemical measurements and electron microscopy. It was found that the electrochemical corrosion behavior of graphite is significantly different from one other, and the corrosive potential difference between carbide ad the matrix is the main driving force of the different phase corrosions. Among them, the center A type and edge D type graphite exhibited the highest corrosion resistance. The corrosion of white iron is worst, because there are so many type carbides in white iron and so there is an obvious tendency to produce micro-cell in white iron.


Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 950 ◽  
Author(s):  
Zequn Yu ◽  
Yuecheng Dong ◽  
Xin Li ◽  
Jingzhe Niu ◽  
Igor Alexandrov ◽  
...  

The aim of this study was to investigate the corrosion resistance of ultrafine-grained (UFG) Ti-6Al-7Nb fabricated by equal channel angular pressing (ECAP) and coarse-grained (CG) Ti- 6Al- 7Nb. The microstructure of each specimen was investigated by the electron backscattered diffraction (EBSD) method. The corrosion behavior of each specimen was determined by electrochemical measurement in Ringer’s solution. The surface corroded morphologies and oxide film formed on Ti-6Al-7Nb alloy after electrochemical measurement were investigated by scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). EBSD investigation shows that the grain size of UFG Ti-6Al-7Nb decreased to ~0.4 µm, accompanied by low angle grain boundaries (LAGBs) accounting for 39%. Potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) results indicated that UFG Ti-6Al-7Nb alloy possessed a better corrosion resistance. The surface corroded morphologies revealed many small and shallow corrosion pits, which can be attributed to the good compactness of the oxide film and a rapid self- repairing ability of the UFG Ti-6Al-7Nb alloy.


2012 ◽  
Vol 189 ◽  
pp. 36-39
Author(s):  
Hai Jiao Yang ◽  
Sheng Tao Zhang ◽  
Lei Zhang

The corrosion behavior of copper in halide solutions was investigated by cyclic voltammetry, potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). On this basis, the mechanism of electrochemical corrosion behavior of Cu in halide solutions has been analyzed. The study explores the corrosive effect of the halide ions on copper materials and provides a theoretical basis for the inhibition of halide ions on the corrosion of copper materials.


2020 ◽  
Vol 67 (5) ◽  
pp. 465-472
Author(s):  
Wei Luo ◽  
Lei Hu ◽  
Yimin Xv ◽  
Jian Zhou ◽  
Wentao Xv ◽  
...  

Purpose This paper aims to focus on an assessment of the electrochemical corrosion performance of bulk NC copper in a variety of corrosion environments. Design/methodology/approach The electrochemical corrosion behavior of bulk nanocrystalline (NC) copper prepared by inert gas condensation and in situ warm compress technique was studied by using potentiodynamic polarization and electrochemical impedance spectroscopy tests in de-aerated 0.1 M NaOH solution. Findings NC copper exhibited a typical active-passive-transpassive behavior with the formation of duplex passive films, which was qualitatively similar to coarse-grain (CG) copper. Although a compact passive film formed on NC copper surface, the corrosion resistance of NC copper was lower in comparison with CG copper. The increase in corrosion rate for NC copper was mainly attributed to the high activity of surface atoms and intergranular atoms. These atoms led to an enhancement of passive ability and an increase of dissolution rate of passive film in oxygen-deficiency solution. For NC copper, the corrosion resistance decreased as grain size increased in NC range. Originality/value The difference in corrosion resistance between bulk NC copper and its CG counterpart is dependent upon the corrosion solution. In a previous work, the potentiodynamic polarization tests revealed that NC copper bulks (grain size 48, 68, 92 nm) had identical corrosion resistance to CG copper bulk in naturally aerated 0.1 M NaOH solution. The results might be related to the dissolved oxygen in the medium.


Sign in / Sign up

Export Citation Format

Share Document