scholarly journals Enhancement of Uniform Elongation by Temperature Change during Tensile Deformation in a 0.2C TRIP Steel

Metals ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 2053
Author(s):  
Noriyuki Tsuchida ◽  
Stefanus Harjo
Keyword(s):  
Tensile Test ◽  
Temperature Change ◽  
Deformation Behavior ◽  
Tensile Deformation ◽  
Uniform Elongation ◽  
True Strain ◽  
High Strength ◽  
Tensile Tests ◽  
Transformation Rate ◽  
Trip Effect

It is important to control the deformation-induced martensitic transformation (DIMT) up to the latter part of the deformation to improve the uniform elongation (U.El) through the TRIP effect. In the present study, tensile tests with decreasing deformation temperatures were conducted to achieve continuous DIMT up to the latter part of the deformation. As a result, the U.El was improved by approximately 1.5 times compared with that in the tensile test conducted at 296 K. The enhancement of the U.El in the temperature change test was discussed with the use of neutron diffraction experiments. In the continuous DIMT behavior, a maximum transformation rate of about 0.4 was obtained at a true strain (ε) of 0.2, which was larger than that in the tensile test at 296 K. The tensile deformation behavior of ferrite (α), austenite (γ), and deformation-induced martensite (α′) phases were investigated from the viewpoint of the fraction weighted phase stress. The tensile test with a decreasing deformation temperature caused the increase of the fraction weighted phase stress of α and that of α′, which was affected by the DIMT behavior, resulting in the increase in the work hardening, and also controlled the ductility of α and α′, resulting in the enhancement of the U.El. Especially, the α phase contributed to maintaining high strength instead of α′ at a larger ε. Therefore, not only the DIMT behavior but also the deformation behavior of γ, α, and α′ are important in order to improve U.El due to the TRIP effect.

Hot deformation behavior of low carbon advanced high strength steel (AHSS) microalloyed with boron

2009 ◽  
Vol 1243 ◽  
Author(s):  
I. Mejía ◽  
S. González-Sala ◽  
J.M. Cabrera
Keyword(s):  
High Temperature ◽  
Deformation Behavior ◽  
True Strain ◽  
High Strength ◽  
Tensile Tests ◽  
Strain Rates ◽  
Low Carbon ◽  
Compression Tests ◽  
Advanced High Strength Steel ◽  
Different Temperatures

ABSTRACTThis research work deals the influence of boron content on the high temperature deformation behavior of a low carbon advanced high strength steel (AHSS). For this purpose high temperature tensile and compression tests are carried out at different temperatures and constant true strain rates by using an Instron testing machine equipped with a radiant cylindrical furnace. Tensile tests are carried out at different temperatures (650, 750, 800, 900 and 1000°C) at a constant true strain rate of 0.001 s-1. Uniaxial hot compression tests are also performed over a wide range of temperatures (950, 1000, 1050 and 1100°C) and constant true strain rates (10-3, 10-2 and 10-1 s-1). In general, experimental results of hot tensile tests show an improvement of the hot ductility of the AHSS microalloyed with boron, although poor ductility at low temperatures (650 and 750°C). The fracture surfaces of the AHSS tested at temperatures showing the higher ductility (800, 900 and 1000°C) indicate that the fracture mode is a result of ductile failure, whereas in the region of poor ductility the fracture mode is of the ductile-brittle type failure. On the other hand, experimental results of hot compression tests show that both peak stress and peak strain tend to decrease in the AHSS microalloyed with boron, which indicates that boron generates a sort of solid solution softening effect in similar a way to other interstitial alloying elements in steel. Likewise, hot flow curves of the AHSS microalloyed with boron show an acceleration of the onset of dynamic recrystallization (DRX) and a delay of the recrystallization kinetics. Results are discussed in terms of boron segregation towards austenitic grain boundaries and second phase particles precipitation during plastic deformation and cooling.

scholarly journals Design of an Effective Heat Treatment Involving Intercritical Hardening for High Strength/High Elongation of 0.2C–3Al–(6–8.5)Mn–Fe TRIP Steels: Microstructural Evolution and Deformation Behavior

Metals ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 1275 ◽  
Author(s):  
Yanjie Mou ◽  
Zhichao Li ◽  
Xiaoteng Zhang ◽  
Devesh Misra ◽  
Lianfang He ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Stress Relaxation ◽  
Deformation Behavior ◽  
High Strength ◽  
Total Elongation ◽  
Trip Effect ◽  
High Ductility ◽  
Trip Steels ◽  
Effective Heat ◽  
High Elongation

High strength/high elongation continues to be the primary challenge and focus for medium-Mn steels. It is elucidated herein via critical experimental analysis that the cumulative contribution of transformation-induced plasticity (TRIP) and microstructural constituents governs high strength/high elongation in 0.2C–3Al–(6–8.5)Mn–Fe steels. This was enabled by an effective heat treatment involving a combination of intercritical hardening and tempering to obtain high strength/high ductility. An excellent combination of high ultimate tensile strength of 935–1112 MPa and total elongation of 35–40% was obtained when the steels were subjected to intercritical hardening in the temperature range of 700–750 °C and low tempering at 200 °C. The intercritical hardening impacted the coexistence of austenite, ferrite, and martensite, such that the deformation behavior varied with the Mn content. The excellent obtained properties of the steels are attributed to the cumulative contribution of the enhanced TRIP effect of austenite and the microstructural constituents, ferrite and martensite. The discontinuous TRIP effect during deformation involved stress relaxation, which was responsible for the high ductility. Lamellar austenite, unlike the equiaxed microstructure, is envisaged to induce stress relaxation during martensitic transformation, resulting in the discontinuous TRIP effect.

scholarly journals Thermomechanical response of Mg AZ31 at different levels of temperatures and strain rates

2019 ◽  
Vol 304 ◽  
pp. 01025
Author(s):  
Farid Abed ◽  
Wael Abuzaid ◽  
Yomna Morad
Keyword(s):  
True Strain ◽  
Weight Ratio ◽  
High Strength ◽  
Tensile Tests ◽  
Industrial Applications ◽  
Gauge Length ◽  
Image Correlation ◽  
Strain Rates ◽  
Localized Deformation ◽  
The Difference

Magnesium alloys’ mechanical behavior has received increasing attention because of its high strength to weight ratio making them ideal for various industrial applications, such as vehicle components, transportation and aerospace. The objective of this work is to closely investigate the thermo-mechanical properties of magnesium alloy AZ31 at different strain rates and temperatures. Tensile tests are conducted on a 30 mm gauge length MgAZ31 specimens at two quasi-static strain rates (1.11x10−3 s−1 and 0.28 s−1) at a range of temperatures between 25 ºC and 250 ºC. Digital Image Correlation (DIC) system was used to calculate the true strain and provide quantitative assessment of the localized deformation response at high levels of deformation. The stress-strain responses of MgAZ31 show that the yield stress as well as the ultimate stress decreases as temperature increases and strain rate decreases. Moreover, the difference between the yield and ultimate stresses at both strain rates increases rapidly as temperature increases. The material shows a significant increase in ductility as temperature increases while the modulus of elasticity remains independent of change in strain rates.

Mechanical Behavior of Materials under Tensile Loads

2004 ◽  
pp. 13-31
Keyword(s):  
Tensile Test ◽  
Mechanical Behavior ◽  
Tensile Deformation ◽  
True Strain ◽  
Strain Curve ◽  
Tensile Specimen ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Mathematical Expressions ◽  
Reduction In Area

Abstract This chapter focuses on mechanical behavior under conditions of uniaxial tension during tensile testing. It begins with a discussion on the parameters that are used to describe the engineering stress-strain curve of a metal, namely, tensile strength, yield strength or yield point, percent elongation, and reduction in area. This is followed by a section describing the parameters determined from the true stress-true strain curve. The chapter then presents the mathematical expressions for the flow curve. Next, it reviews the effect of strain rate and temperature on the stress-strain curve. The chapter then describes the instability in tensile deformation and stress distribution at the neck in the tensile specimen. It discusses the processes involved in ductility measurement and notch tensile test in tensile specimens. The parameter that is commonly used to characterize the anisotropy of sheet metal is covered. Finally, the chapter covers the characterization of fractures in tensile test specimens.

Predicting Edge Cracks on Shear-Cut High-Strength Steels by Modified Uniaxial Tensile Tests

2016 ◽  
Vol 703 ◽  
pp. 49-55 ◽  
Author(s):  
Martin Feistle ◽  
Isabella Pätzold ◽  
Roland Golle ◽  
Wolfram Volk
Keyword(s):  
Tensile Test ◽  
Measurement Method ◽  
High Strength Steels ◽  
High Strength ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Forming Process ◽  
Contact Measurement ◽  
Edge Cracks ◽  
Near Future

During the forming of high-strength steels, edge cracks occur unexpectedly on sheared edges e.g. during collar forming. A non-contact measurement method based on the well-known tensile test was developed. It allows the investigation of the formation of edge cracks under tensile loads and determining general criteria to predict the formation of edge cracks during a specific forming process. The criteria are validated experimentally by means of the collar-forming test. In conjunction with the proposed line-fit-method these criteria can be implemented easily in FEM software in the near future for the prediction of edge cracks.

Constitutive Modeling for Tensile Behaviors of Ultra-high-strength-steel BR1500HS at Different Temperatures and Strain Rates

2015 ◽  
Vol 34 (5) ◽  
Author(s):  
Guo-Zheng Quan ◽  
Dong-sen Wu ◽  
An Mao ◽  
Yan-dong Zhang ◽  
Yu-feng Xia ◽  
...  
Keyword(s):  
Constitutive Modeling ◽  
High Strength Steel ◽  
Deformation Behavior ◽  
Tensile Deformation ◽  
High Strength ◽  
Strain Rate Range ◽  
Strain Rates ◽  
Tensile Deformation Behavior ◽  
Ultra High Strength Steel ◽  
Different Temperatures

AbstractIn order to investigate the tensile deformation behavior of ultra-high-strength-steel BR1500HS, a series of isothermal tensile experiments were carried out in a temperature range of 1023˜1123 K and a strain rate range of 0.01˜10 s

Effects of Strain Rate on Tensile Deformation Behavior of Quenching and Partitioning Steel

2013 ◽  
Vol 749 ◽  
pp. 401-406 ◽  
Author(s):  
Chao Liu ◽  
Lei Wang ◽  
Yang Liu
Keyword(s):  
Strain Rate ◽  
Deformation Behavior ◽  
Retained Austenite ◽  
Tensile Deformation ◽  
Auto Industry ◽  
Trip Effect ◽  
Quenching And Partitioning ◽  
Tensile Deformation Behavior

The effects of strain rate on the tensile deformation behavior of quenching and partitioning (Q&P) steel applied to the auto industry were investigated. The results indicated that the strength of Q&P steel raised with increasing strain rate. The variation of elongation which presented the trend of declining (10-4 s-1~101 s-1) followed by rising to the peak (8×101 s-1) then falling again (102 s-1~103 s-1), is mainly caused by the transformation from retained austenite to martensite, namely the TRIP effect.

Finite Element Modeling of Deformation Behavior of Steel Specimens under Various Loading Scenarios

2015 ◽  
Vol 651-653 ◽  
pp. 969-974 ◽  
Author(s):  
Dilip Banerjee ◽  
Mark Iadicola ◽  
Adam Creuziger ◽  
Tim Foecke
Keyword(s):  
Finite Element ◽  
Deformation Behavior ◽  
Stress Measurement ◽  
High Strength Steels ◽  
High Strength ◽  
Tensile Tests ◽  
Image Correlation ◽  
Uniaxial Tensile ◽  
Fe Model ◽  
Strain Paths

Lightweighting materials (e.g., advanced high strength steels, aluminum alloys etc.) are increasingly being used by automotive companies as sheet metal components. However, accurate material models are needed for wider adoption. These constitutive material data are often developed by applying biaxial strain paths with cross-shaped (cruciform) specimens. Optimizing the design of specimens is a major goal in which finite element (FE) analysis can play a major role. However, verification of FE models is necessary. Calibrating models against uniaxial tensile tests is a logical first step. In the present study, reliable stress-strain data up to failure are developed by using digital image correlation (DIC) technique for strain measurement and X-ray techniques and/or force data for stress measurement. Such data are used to model the deformation behavior in uniaxial and biaxial tensile specimens. Model predictions of strains and displacements are compared with experimental data. The role of imperfections on necking behavior in FE modeling results of uniaxial tests is discussed. Computed results of deformation, strain profile, and von Mises plastic strain agree with measured values along critical paths in the cruciform specimens. Such a calibrated FE model can be used to obtain an optimum cruciform specimen design.

Mechanical Properties of Fine-Grained and Ultrafine-Grained Ti-6Al-4V with Equiaxed and Bimodal Microstructures

2016 ◽  
Vol 879 ◽  
pp. 344-349 ◽  
Author(s):  
Yan Chong ◽  
Nobuhiro Tsuji
Keyword(s):  
Mechanical Properties ◽  
Thermomechanical Processing ◽  
Uniform Elongation ◽  
True Strain ◽  
Tensile Tests ◽  
Initial Microstructure ◽  
Equiaxed Microstructure ◽  
Fine Grained ◽  
Ultrafine Grained ◽  
Mean Grain Size

With the purpose of fabricating equiaxed and bimodal Ti-6Al-4V alloy with different grain/primary α (αp) sizes, thermomechanical processing and additional annealing were carried out on samples with martensite initial microstructure. Deformation at 700°C with a strain rate of 0.01s-1 to a true strain of 0.8 could effectively break the martensite initial microstructure into ultrafine-grained (UFG) equiaxed microstructure (mean grain size of 0.51μm) with reasonable uniformity. Subsequent annealing at 930°C with different periods were conducted to change the equiaxed microstructure into bimodal microstructures. The holing time proved to be more critical than heating rate for determining the αp size. An UFG bimodal Ti-6Al-4V with the average αp size of 0.55μm was successfully obtained for the first time by annealing the UFG equiaxed Ti-6Al-4V at 930°C for 2 seconds. The mechanical properties of the equiaxed and bimodal Ti-6Al-4V with different grain/αp sizes were evaluated by tensile tests at room temperature. The bimodal Ti-6Al-4V showed superior balance between strength and uniform elongation than that of the equiaxed Ti-6Al-4V. Moreover, the uniform elongation in the bimodal Ti-6Al-4V was nearly unaffected by reduction of the αp size.

Effect of Pulse Current on Tensile Deformation Behavior of IN718 Alloy

2012 ◽  
Vol 509 ◽  
pp. 56-63 ◽  
Author(s):  
Yang Liu ◽  
Lei Wang ◽  
Fei Feng ◽  
Xu Dong Lu ◽  
Bei Jiang Zhang
Keyword(s):  
Tensile Test ◽  
Deformation Behavior ◽  
Room Temperature ◽  
Pulse Current ◽  
Tensile Deformation ◽  
Dislocation Motion ◽  
Deformation Resistance ◽  
Deformation Ability ◽  
Lower Temperature ◽  
Strength And Plasticity

The pulse current was performed on the IN718 alloy during tensile test at room temperature and elevated temperature in the present study. The effect of pulse current on the deformation behavior of the alloy and the mechanisms were investigated. The results show that the deformation resistance decreases and the elongation increases significantly of IN718 alloy during tensile test at room temperature and 1073 K with the increase of pulse current. And the effect of pulse current on the strength and plasticity of the alloy increases as pulse current energy increases. The electroplastic effect of pulse current can promote the dislocation motion, and thus decrease the deformation resistance of the alloy during the tensile deformation. The pulse current reduces the starting temperature of recrystallization, promotes the recrystalllization nucleation, and thus makes it possible that the dynamic recrystallization would occur at lower temperature than that in the conventional temperature field. This is the main reason for the decrease of deformation resistance and the increase of plastic deformation ability of IN718 alloy under pulse current.

Sign in / Sign up

Export Citation Format

Share Document