scholarly journals Cooperative Effect of Li Content and Equal-Channel Angular Pressing on Microstructure and Mechanical Properties of Al-Mg-Li Alloy

Metals ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 840
Author(s):  
Ting Yuan ◽  
Jinghua Jiang ◽  
Yuna Wu ◽  
Zhipeng Yuan ◽  
Aibin Ma ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Equal Channel Angular Pressing ◽  
High Performance ◽  
Cast Alloy ◽  
Cooperative Effects ◽  
Specific Strength ◽  
Aerospace Applications ◽  
Angular Pressing ◽  
Al Matrix Composites ◽  
Li Content

This paper investigated the cooperative effects of Li addition and warm Equal Channel Angular Pressing (ECAP) on improving the mechanical properties of an Al-Mg-Li alloy for further weight reduction. The results showed that more Li addition could obviously refine the grains of the as-cast alloy and reduce its density value to only 2.37 g/cm3 when Li content reached 2.5% (about 12.6% lighter than commercial Al alloys). It also had a pronounced influence on the precipitations in the Al-5.5Mg-xLi-0.1Zr alloy, i.e., the number density and size of Al2MgLi and δ’-Al3Li phases. The yield strength of the as-cast alloy was increased with increasing Li, but the elongation deteriorated due to primary network intergranular Al2MgLi and more δ’ particles in the high Li-containing alloy. The warm multi-pass ECAP process was found to simultaneously improve the strength and ductility of the Al-Mg-Li alloys, and greatly alleviate the detrimental effect of Li addition on the elongation, thereby making the ultrafine-grained (UFG) alloys, a good combination of lightweight and high performance, very attractive for aerospace applications for much higher specific strength than both Al matrix composites and Mg alloys.

scholarly journals Microstructure and Properties of Mg-Zn-Y Alloy Powder Compacted by Equal Channel Angular Pressing

Materials ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 1678 ◽  
Author(s):  
Chun Chiu ◽  
Hong-Min Huang
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Equal Channel Angular Pressing ◽  
Volume Fraction ◽  
Cast Alloy ◽  
Milled Powder ◽  
Microstructural Characterization ◽  
Compressive Yield Strength ◽  
Lpso Phase ◽  
Angular Pressing

Mg97Zn1Y2 (at %) alloy with a long period stacking ordered (LPSO) phase has attracted a great deal of attention due to its excellent mechanical properties. It has been reported that this alloy could be fabricated by warm extrusion of rapid solidified alloy powders. In this study, an alternative route combining mechanical milling and equal channel angular pressing (ECAP) was selected to produce the bulk Mg97Zn1Y2 alloy. Microstructural characterization, mechanical properties and corrosion behavior of the ECAP-compacted alloys were studied. The as-cast alloy contained α-Mg and LPSO-Mg12Zn1Y1 phase. In the as-milled powder, the LPSO phase decomposed and formed Mg24Y5 phase. The ECAP-compacted alloy had identical phases to those of the as-milled sample. The compacted alloy exhibited a hardness of 120 HV and a compressive yield strength of 308 MPa, which were higher than those of the as-cast counterpart. The compacted alloy had better corrosion resistance, which was attributed to the reduced volume fraction of the secondary phase resulting in lower microgalvanic corrosion in the compacted alloy. The increase in Y content in the α-Mg matrix also contributed to the improvement of corrosion resistance.

scholarly journals Effects of equal channel angular pressing and heat treatments on the microstructures and mechanical properties of selective laser melted and cast AlSi10Mg alloys

2021 ◽  
Vol 21 (3) ◽  
Author(s):  
Przemysław Snopiński ◽  
Mariusz Król ◽  
Marek Pagáč ◽  
Jana Petrů ◽  
Jiří Hajnyš ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Equal Channel Angular Pressing ◽  
Heat Treatments ◽  
Electron Backscattered Diffraction ◽  
Angular Pressing ◽  
Low Temperature Annealing ◽  
Transmission Electron ◽  
Before And After ◽  
The Impact

AbstractThis study investigated the impact of the equal channel angular pressing (ECAP) combined with heat treatments on the microstructure and mechanical properties of AlSi10Mg alloys fabricated via selective laser melting (SLM) and gravity casting. Special attention was directed towards determining the effect of post-fabrication heat treatments on the microstructural evolution of AlSi10Mg alloy fabricated using two different routes. Three initial alloy conditions were considered prior to ECAP deformation: (1) as-cast in solution treated (T4) condition, (2) SLM in T4 condition, (3) SLM subjected to low-temperature annealing. Light microscopy, transmission electron microscopy, X-ray diffraction line broadening analysis, and electron backscattered diffraction analysis were used to characterize the microstructures before and after ECAP. The results indicated that SLM followed by low-temperature annealing led to superior mechanical properties, relative to the two other conditions. Microscopic analyses revealed that the partial-cellular structure contributed to strong work hardening. This behavior enhanced the material’s strength because of the enhanced accumulation of geometrically necessary dislocations during ECAP deformation.

Microstructures and Mechanical Properties of AZ61 Mg Alloy Processed by Equal Channel Angular Pressing

2012 ◽  
Vol 468-471 ◽  
pp. 2124-2127 ◽  
Author(s):  
Shao Feng Zeng ◽  
Kai Huai Yang ◽  
Wen Zhe Chen
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Equal Channel Angular Pressing ◽  
Uniform Elongation ◽  
Considerable Decrease ◽  
Angular Pressing ◽  
Az61 Magnesium Alloy ◽  
Average Grain Size ◽  
Microstructures And Mechanical Properties ◽  
Bimodal Grain Size

Equal channel angular pressing (ECAP) was applied to a commercial AZ61 magnesium alloy for up to 8 passes at temperatures as low as 473K. Microstructures and mechanical properties of as-received and ECAP deformed samples were investigated. The microstructure was initially not uniform with a “bimodal” grain size distribution but became increasingly homogeneous with further ECAP passes and the average grain size was considerably reduced from over 26 μm to below 5 μm. The ultimate tensile strength (UTS) decreases clearly after one pass, but increases significantly up to two passes, and then continuously slowly decreases up to six passes, and again increases slightly up to eight passes. In contrast, the uniform elongation increased significantly up to 3 passes, followed by considerable decrease up to 8 passes. These observations may be attributed to combined effects of grain refinement and texture development.

Morphology of Rigid-Rod Molecular Composites: An Overview

1988 ◽  
Vol 134 ◽  
Author(s):  
Stephen J. Krause
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
Morphological Characterization ◽  
High Ratio ◽  
Structure Property ◽  
Chain Polymer ◽  
Specific Strength ◽  
Composite Systems ◽  
Molecular Composites ◽  
Rigid Rod

ABSTRACTRigid-rod molecular composites are a new class of high performance structural polymers which have high specific strength and modulus and also high thermal and environmental resistance. A rigid-rod, extended chain polymer component is used to reinforce a matrix of a ductile polymer with the intent of achieving a “composite” on the molecular level. After synthesis, the key to producing a molecular composite is to control morphology to disperse the reinforcing rod molecules as finely as possible in the matrix polymer. Individual rod molecules or bundles of molecular rods must have dimensions which result in a high ratio of length to width (aspect ratio) for efficient reinforcement. To achieve this, the reinforcing rod component must not phase separate at any stage of processing. Morphological characterization techniques, which can measure the orientation and dispersion (or, conversely, the degree of phase separation) of rod molecules provide the tools for correlating theoretically predicted and experimentally observed mechanical properties. Various morphological techniques which have been applied to molecular composite systems will be reviewed, including wide angle x-ray scattering and scanning and transmission electron microscopy. Structure-property correlations for molecular composite systems will be discussed with regard to models for mechanical properties. Application of new morphological techniques will also be discussed.

Sign in / Sign up

Export Citation Format

Share Document