scholarly journals The Development of a Low-Cost Method for Monitoring Methane Leakage from the Subsurface of Natural Gas Fields

Methane ◽  
2021 ◽  
Vol 1 (1) ◽  
pp. 24-37
Author(s):  
Muhammad Alfiza Farhan ◽  
Yuichi Sugai ◽  
Nuhindro Priagung Widodo ◽  
Syafrizal Syafrizal
Keyword(s):  
Activated Carbon ◽  
Natural Gas ◽  
Methane Concentration ◽  
Low Cost ◽  
Gas Field ◽  
Methane Leakage ◽  
Wide Scale ◽  
Adsorbed Methane ◽  
In The Beginning ◽  
Gas Fields

The leakage of methane from the subsurface on the coalfield or natural gas field invariably becomes an important issue nowadays. In notable addition, materials such as activated carbon, zeolites, and Porapak have been successfully identified as adsorbents. Those adsorbents could adsorb methane at atmospheric pressure and room temperature. Therefore, in this scholarly study, a new method using adsorbents to detect points of methane leakage that can cover a wide-scale area was developed. In the beginning, the most capable adsorbent should be determined by quantifying adsorbed methane amount. Furthermore, checking the possibility of adsorption in the column diffusion and desorption method of adsorbents is equally necessary. The most capable adsorbent was activated carbon (AC), which can adsorb 1.187 × 10−3 mg-CH4/g-AC. Hereinafter, activated carbon successfully can adsorb methane through column diffusion, which simulates the situation of on-site measurement. The specific amount of adsorbed methane when the initial concentrations of CH4 in a bag were 200 ppm, 100 ppm, and 50 ppm was found to be 0.818 × 10−3 mg-CH4/g-AC, 0.397 × 10−3 mg-CH4/g-AC, 0.161 × 10−3 mg-CH4/g-AC, respectively. Desorption of activated carbon analysis shows that methane concentration increases during an hour in the temperature bath under 80 °C. In conclusion, soil methane leakage points can be detected using activated carbon by identifying the observed methane concentration increase.

Natural gas separation at CO2CRC's Otway National Research Facility

2019 ◽  
Vol 59 (2) ◽  
pp. 803
Author(s):  
Abdul Qader ◽  
Jai Kant Pandit
Keyword(s):  
Natural Gas ◽  
Gas Separation ◽  
Cost Effective ◽  
Commercial Application ◽  
Research Facility ◽  
Gas Field ◽  
South Wales ◽  
Effective Manner ◽  
Gas Fields ◽  
The University

CO2CRC, in collaboration with the University of Melbourne and the University of New South Wales, is testing two novel CO2 capture technologies designed for both on-shore and off-shore natural gas applications in a state-of-the-art experimental capture rig at CO2CRC’s Otway National Research Facility. The goal is to develop robust and compact technology for high pressure natural gas separation over a range of adjusted high CO2 concentrations mimicking various gas field conditions. These technologies would facilitate developing new gas fields to recover methane in a cost-effective manner which is currently uneconomical with conventional technologies. In the first stage of testing, commercially available materials (adsorbents and membranes) were used for benchmarking. Results from both adsorbent and membrane technologies are encouraging with respect to recovery and purity of CO2 and methane with the prospect of commercial application.

scholarly journals Adsorption of CO2 and Methane on Covalent Organic Polymer

2018 ◽  
Vol 43 ◽  
pp. 01001 ◽  
Author(s):  
Siew-Pei Lee ◽  
N. Mellon ◽  
Azmi M. Shariff ◽  
Jean-Marc Leveque
Keyword(s):  
Natural Gas ◽  
Selective Adsorption ◽  
Low Cost ◽  
Atmospheric Condition ◽  
Organic Polymer ◽  
Co2 Uptake ◽  
Co2 Removal ◽  
Gas Field ◽  
Adsorbent Regeneration ◽  
Adsorption Of Co2

Development of covalent organic polymer (COP) is a potential new class of adsorbent for CO2 separation from natural gas mainly due to their good hydrothermal stability, chemical tuning flexibility and low cost. CO2 and methane adsorption on COP-1 was studied under atmospheric condition (101.3 kPa, 298 K). COP-1 was synthesized via catalyst-free polycondensation of cyanuric chloride and piperazine. The properties of COP-1 were characterized using several analytical methods such as Fourier Transform Infra-Red (FTIR), N2 adsorption and desorption measurement and Field Transmission Electron Microscopy in coupled of Energy Dispersive X-ray Spectroscopy (FESEM-EDS). Reversible CO2 adsorption isotherm on COP-1 reflects low heat of adsorption which is beneficial to energy minimization in adsorbent regeneration process. Furthermore, moderate specific surface area COP-1 (88.5 m2/g) shows about nine times CO2 uptake higher than methane. The highly selective adsorption performance provides a promising insight in application of COP adsorbent for CO2 removal in natural gas field.

scholarly journals Spectrometric measurements of atmospheric propane (C<sub>3</sub>H<sub>8</sub>)

2021 ◽  
Vol 21 (13) ◽  
pp. 10727-10743
Author(s):  
Geoffrey C. Toon ◽  
Jean-Francois L. Blavier ◽  
Keeyoon Sung ◽  
Katelyn Yu
Keyword(s):  
New Mexico ◽  
Natural Gas ◽  
Absorption Feature ◽  
Strongly Correlated ◽  
Permian Basin ◽  
Gas Field ◽  
Solar Absorption ◽  
Back Trajectories ◽  
Oil And Natural Gas ◽  
Gas Fields

Abstract. We report measurements of atmospheric C3H8 from analysis of ground-based solar absorption spectra from the Jet Propulsion Laboratory (JPL) MkIV interferometer. Using the strong Q-branch absorption feature at 2967 cm−1, we can measure C3H8 in locations where its abundance is enhanced by proximity to sources (e.g., large natural gas fields, megacities). A case study of MkIV C3H8 measurements from Fort Sumner, New Mexico, shows that amounts are strongly correlated with ethane (C2H6) and with back-trajectories from SE New Mexico and western Texas, where the Permian Basin oil and natural gas field is located. Measurements from JPL, California, also show large C3H8 enhancements on certain days but more correlated with CO than C2H6. From high-altitude balloon-borne MkIV solar occultation measurements, C3H8 was not detected at any altitude (5–40 km) in any of the 25 flights.

scholarly journals Geological structure, sedimentary environments and oil and gas potential of Oligocene-Miocene and Pliocene-Pleistocene deposits in the Levant basin

Georesursy ◽  
2019 ◽  
Vol 21 (2) ◽  
pp. 80-93
Author(s):  
Aleksandr I. Konyukhov ◽  
Vadim F. Sharafutdinov ◽  
Vasiliy V. Kalabin
Keyword(s):  
Natural Gas ◽  
Oil And Gas ◽  
Geological Structure ◽  
Carbonate Reservoir ◽  
Gas Field ◽  
Economic Interests ◽  
Biogenic Methane ◽  
Sedimentary Environments ◽  
Levant Basin ◽  
Gas Fields

An extensive sedimentary-rock basin is located within the continental margin of the Levant, where, since 2008, numerous natural gas fields have been discovered, including Tamar, Tannin, Dalit and Leviathan in the offshore zone of Israel, and Aphrodite in the zone of economic interests of Cyprus. Deposits of biogenic methane, located in the deep-water Levantine depression, are confined to terrigenous sandstones of late Oligocene-Early Miocene age. The discovery of another gas field Zohr in 2015 in the area of the underwater uplift of Eratosthenes caused a real boom among petroleum geologists. The fact is that natural gas deposit with reserves of about 30 trillion cubic feet is not in the terrigenous, but carbonate reservoir of the reef genesis, which opens significant prospects for the discovery of new large gas accumulations in the area of this major uplift. All the above-mentioned deposits are located in the same range of sea depths (1600-2000 m) in the propagation zone of the Messinian evaporites, that serves as a regional screen. An analysis of the materials currently published suggests that in the epochs of the sediments formation in which gas deposits are located, the depths of the seabed in the southern regions of the Levant depression were significantly lower compared to modern ones. Currently, there is no doubt that in the Levant region there is the largest gas-bearing basin in the Mediterranean region, with gas reserves of several hundred trillion cubic feet.

scholarly journals Spectrometric measurements of atmospheric propane (C<sub>3</sub>H<sub>8</sub>)

2020 ◽  
Author(s):  
Geoffrey C. Toon ◽  
Jean-Francois L. Blavier ◽  
Keeyoon Sung ◽  
Katelyn Yu
Keyword(s):  
New Mexico ◽  
Natural Gas ◽  
Absorption Feature ◽  
Strongly Correlated ◽  
Permian Basin ◽  
Gas Field ◽  
Solar Absorption ◽  
Back Trajectories ◽  
Oil And Natural Gas ◽  
Gas Fields

Abstract. We report measurements of atmospheric C3H8 from analysis of ground-based, solar absorption spectra from the JPL MkIV interferometer. Using the strong Q-branch absorption feature at 2967 cm−1, we can measure C3H8 in locations where its abundance is enhanced by proximity to sources (e.g., large natural gas fields, mega-cities). A case study of MkIV C3H8 measurements from Ft. Sumner, New Mexico, show large variations that are strongly correlated with ethane (C2H6) amounts and with back-trajectories from SE New Mexico and West Texas, where the Permian Basin oil and natural gas field is located. Measurements from JPL, California, also show large C3H8 enhancements on certain days, but more correlated with CO than C2H6. From MKIV solar occultation measurements from balloon, C3H8 was not detected at any altitude in any flight.

scholarly journals Lithological composition and reservoir properties of Lower Ordovician Majiagou formation in the gas field Tabamiao (Ordos Basin, China)

2016 ◽  
pp. 81-86
Author(s):  
Y. Wang
Keyword(s):  
Natural Gas ◽  
Ordos Basin ◽  
Reservoir Properties ◽  
Gas Field ◽  
The Core ◽  
Lower Ordovician ◽  
Definition Of ◽  
Lithological Composition ◽  
Gas Fields ◽  
Carbonate Deposits

Ordos Basin is concentrated rich areas of coal, natural gas and oil. In last years it is becoming an important mineral resource and energy base of China. To the most well-known and good studied gas fields belong Sulige and Tabamiao, where natural gas takes place in carbonate rocks of Early Ordovician time. As the result of an investigation that made by author, there is a definition of five types of reservoirs which lay in the core of weathering of Ordovician carbonate deposits.

scholarly journals Experimental Measurement of Bulk Thermal Conductivity of Activated Carbon with Adsorbed Natural Gas for ANG Energy Storage Tank Design Application

Energies ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 682 ◽  
Author(s):  
Atila Ertas ◽  
Christopher T. R. Boyce ◽  
Utku Gulbulak
Keyword(s):  
Thermal Conductivity ◽  
Activated Carbon ◽  
Natural Gas ◽  
Storage Tanks ◽  
Adsorbed Natural Gas ◽  
Adsorbed Methane ◽  
Temperature And Pressure ◽  
Tank Design ◽  
Change Material ◽  
Effective Design

The development of adsorptive natural gas storage tanks for vehicles requires the synthesis of many technologies. The design for an effective Adsorbed Natural Gas (ANG) tank requires that the tank be filled isothermally within a five-minute charge time. The heat generated within the activated carbon is on the order of 150 MJ/m 3 of storage volume. The tank can be effectively buffered using Phase Change Material (PCM) to absorb the heat. The effective design of these tanks requires knowledge of the thermal properties of activated carbon with adsorbed methane. This paper discusses experimental measurements of the thermal conductivity of activated carbon with adsorbed methane. It was found that within the tank the thermal conductivity remains almost constant within the temperature and pressure ranges that ANG tanks will operate.

Geoeconomic Leverage of Natural Gas Resources in the Mediterranean

2019 ◽  
Vol 12 (4) ◽  
pp. 141-155 ◽  
Author(s):  
Ahmed Mahdi
Keyword(s):  
Natural Gas ◽  
Economic Resources ◽  
Tel Aviv ◽  
Economic Influence ◽  
The Mediterranean ◽  
Influence Attempts ◽  
Gas Fields

This article examines the claim that Israel’s natural gas exports from its Mediterranean gas fields will give geopolitical leverage to Tel Aviv over the importing countries. Using the geoeconomic tradition of Klaus Knorr and others who wrote about applying leverage using economic resources to gain geopolitical advantage, it is argued that certain criteria have to be satisfied for economic influence attempts, and that Israel’s gas exports do not satisfy these criteria. They include the importer’s supply vulnerability, the supplier’s demand vulnerability, and the salience of energy as an issue between both countries. Israeli gas exports to Egypt are used as a case study.

scholarly journals Na0.76V6O15/Activated Carbon Hybrid Cathode for High-Performance Lithium-Ion Capacitors

Materials ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 122
Author(s):  
Renwei Lu ◽  
Xiaolong Ren ◽  
Chong Wang ◽  
Changzhen Zhan ◽  
Ding Nan ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Energy Density ◽  
Power Density ◽  
Cathode Materials ◽  
Low Cost ◽  
Lithium Ion ◽  
High Energy ◽  
Cycling Stability ◽  
High Energy Density ◽  
Artificial Graphite

Lithium-ion hybrid capacitors (LICs) are regarded as one of the most promising next generation energy storage devices. Commercial activated carbon materials with low cost and excellent cycling stability are widely used as cathode materials for LICs, however, their low energy density remains a significant challenge for the practical applications of LICs. Herein, Na0.76V6O15 nanobelts (NaVO) were prepared and combined with commercial activated carbon YP50D to form hybrid cathode materials. Credit to the synergism of its capacitive effect and diffusion-controlled faradaic effect, NaVO/C hybrid cathode displays both superior cyclability and enhanced capacity. LICs were assembled with the as-prepared NaVO/C hybrid cathode and artificial graphite anode which was pre-lithiated. Furthermore, 10-NaVO/C//AG LIC delivers a high energy density of 118.9 Wh kg−1 at a power density of 220.6 W kg−1 and retains 43.7 Wh kg−1 even at a high power density of 21,793.0 W kg−1. The LIC can also maintain long-term cycling stability with capacitance retention of approximately 70% after 5000 cycles at 1 A g−1. Accordingly, hybrid cathodes composed of commercial activated carbon and a small amount of high energy battery-type materials are expected to be a candidate for low-cost advanced LICs with both high energy density and power density.

Sign in / Sign up

Export Citation Format

Share Document